Search Documents

By R. F. Mehl, C. E. Birchenall

SINCE Maxwell1 first considered the self-diffusion process in 1872 its importance in the kinetic theory of matter has been recognized. Until the discovery of isotopes in 1913, a direct measurement of this quantity seemed impossible. The only information that could be gathered indirectly was for gaseous systems for which the kinetic theory was well developed. When methods of direct observation be-came available, investigations on self-diffusion were carried out in condensed phases. In metals these data are presumably of potential importance in the study of recovery, recrystallization, creep, sintering, and related phenomena. Following the pioneer work of Von Hevesy2 and his collaborators, who determined the rate of self-diffusion in lead with the naturally occurring thorium B isotope, several metals have been investigated. Pb, Ag³, Au.6,5, and Cu6,7,8,9 are examples of isotropic crystals existing in only one phase modification. Anisotropy of diffusion has been demonstrated in Bil6 and Znll. This paper is a study of a single metal in two allotropic forms and also of self-diffusion in a body-centered cubic lattice. Despite the fact that the measurements in each of the papers cited on self-diffusion in copper seem to be internally consistent to about 10 to 15 pet, the curves reported by different authors differ by factors of 2 to 4 at the same temperatures. This uncertainty may account, in part, for the failure to establish a successful correlation between the self-diffusion rates and other physical characteristics of the metals. No satisfactory theory of metallic self- diffusion has as yet been proposed to account for all the existing data and to permit estimation in other metals. Experimental Part: Two units of radioactive iron were used in these experiments, each a mixture of Fe53 and Fe59 (12). Fe53 decays by K electron capture and the emission of an X ray with a half life of about 4 years. Fe59 emits two beta spectra, one with a maximum energy of 0.26 Mev, the other 0.46 Mev, and gamma rays of 1.1 and 1.3 Mev, with a half life of about 44 days. They were present in nearly equal concentration initially. The composite half life started at about 50 days and increased as the Fe59 decayed, leaving Fe55 relatively more abundant. After aging a year, the half life was too long to measure significant decay in a month. The absorption properties also changed with time. Because of the importance of the absorption coefficient in the diffusion calculations, it was necessary to determine this quantity frequently over the period during which these experiments were carried out. This correction was unsuspected at the time of publication of notesl3 on this work and accounts for the discrepancy in alpha iron and for part of the discrepancy in gamma iron.* * The data in the present paper supersede those given in the notes entirely. In one note the scale of log D was inadvertently reversed. In addition to the correction for the drift in absorption coefficient, the D values for gamma iron at low temperatures were high owing to insuficient correction for diffusion occurring during heating and cooling through the high temperature part of the alpha range at a rate much slower than that employed in the runs reported here. The high temperature alpha rates are much higher than the low temperature gamma rates and correspond to large equivalent times at these temperatures. These experiments were discarded and new measurements taken. Independent experiments with the same activity units indicated a radioactive contaminant in the iron, but exhaustive attempts to isolate and identify it chemically failed. These experiments? indicate † These experiments will be discussed in a later publication from this laboratory. that the contaminant represented only a trace of little importance in the diffusion results. The active iron was plated from an iron chloride solution. Enough of the solution was dropped on a 1% in. square of filter paper to wet it thoroughly.

Jan 1, 1951

First Session BRASS Wednesday, A.M., Nov. 29 Co-Chairmen: CARTER S. COLE, Staff Engineer, A.S.T.M. E. A. ANDERSON, Chief of Metals Section, Research Div., New Jersey Zinc Co. (of Pa.) Second Session BRASS Wednesday, P.M., Nov. 29 Co-Chairmen: D. K. CRAMPTON, Director of Research, Chase Brass and Copper Co., Inc. A. W. TRACY, Metallurgist, The American Brass Co. Dinner and Technical Session Wednesday Evening, Nov. 29 Toastmaster: N. L. MOCHEL, Manager Metallurgical Engineering, Westinghouse Electric Corp. Talk on "How Do Things Look Today and For the Future" RALPH KELLY, President, Baldwin Locomotive Works Technical Paper on Stress-Corrosion Cracking E. H. Dix, JR., Assistant Director of Research and Chief Metallurgist, Aluminum Company of America Third Session BRASS Thursday, A.M., Nov. 30 Co-Chairmen: W. B. PRICE, Director of Research, Scovill Manufacturing Co. A. L. JAMIESON, Associate Metallurgist, Frankford Arsenal First Session LIGHT METALS Thursday, P.M., Nov. 30 Co-Chairmen: L. L. WYMAN, Metallurgist, General Electric Co. M. A. HUNTER, Professor of Metallurgical Engineering and Head, Dept. of Metallurgical Engineering, Rensselaer Polytechnic Institute Second Session LIGHT METALS Thursday Evening, Nov. 30 Co-Chairmen: R. T. WOOD, Chief Metallurgist, American Magnesium Corp. J. D. HANAWALT, Director, Metallurgical Dept., Dow Chemical Co. First Session STEEL Friday A.M., Dec. I Co-Chairmen: H. S. RAWDON, Chief, Division of Metallurgy, National Bureau of Standards A. L. FEILD, Director of Research, Rustless Iron and Steel Corp. First Session MISCELLANEOUS METALS Friday P.M., Dec. I Co-Chairmen: E. A. ANDERSON, Chief of Metals Section, Research Div., New Jersey Zinc Co. (of Pa.) CARTER S. COLE, Staff Engineer, A.S.T.M.

Jan 1, 1945

By B. E. Sundquist

The various methods based on solution models for obtaining free energies of mixing from miscibility-gap data have been applied to a number of binary-alloy systems. For nine of these systems there exist experimental thermodynamic data that permit a comparison of the results to experiment. It was found that the method of van der Toorn and Tiedema almost invariably leads to results that are physically unacceptable and that vary drastically with small changes in the miscibility-gap parameters. The subregular solution model is found in all cases, except the Al-Zn, Fe-Cr, and Cu-Pb systems, to exaggerate the free energy of mixing by 30 pct or more. The model developed by Lumsden is found to give results that are often in excellent agreement with experiment and which exaggerate the free energy of mixing by no more than 30 pct. These results and others give evidence that the Lumsden treatment of the effect of unequal atomic sizes and of imperfect configurational randomness due to deviations of AB bond energies from the mean of AA and BB bond energies is adequate for most systems. ANALYTIC expressions are frequently proposed for the dependence on composition of the activities of the components of a solution. Because the development of solution theory is incomplete, these expressions contain parameters which must be determined by experiment. The measurement of activities is often difficult and consequently such measurements are less readily available than are measurements of phase equilibria which, under certain conditions, can also be used to evaluate these parameters. For example, suppose it is known that two structurally dissimilar phases, each of known composition, in an n-com-ponent system are at equilibrium at a given temperature and pressure. n equations can be set up in terms of these parameters expressing the equality of the chemical potential of each component in the two phases. In addition, one can write the Gibbs-Duhem equation for each phase that also contains these parameters. Thus, if these n + 2 equations contain n + 2 parameters, these parameters can be determined (at the temperature in question) from the phase diagram alone. If the average number of parameters in each expression for the activity of a given component in a given phase is V then there will be 2nV parameters involved. Equating 2nV to n + 2 shows that, for n + 2, V = 1. If the temperature dependence of each parameter were to be expressed in some explicit form one could use equilibrium conditions at a number of temperatures to increase V. The situation is much improved when the two phases in equilibrium are structurally similar. It can then be assumed that, stably or metastably, two phases will become one at higher temperatures. Thus the number of parameters involved becomes nV instead of 2nV. Hence, V = 2 for n = 2 using only one temperature. (It is implied here that the activity expressions used are valid over the entire composition range.) In this investigation only the equilibrium of two structurally similar, two-component phases (miscibility-gap systems) will be considered. The various proposed solution models will be applied to a number of these systems and the results compared with available experimental results. All of the analytic expressions that have been proposed for the free energy of mixing of a two-component system are of the form where ?Gmix is the free energy of mixing per mole of solution, N1 and N2 are the mole fractions of components 1 and 2, respectively, and f(Ni, T) is some function of composition and temperature. In the "ideal" solution model f = 0. In the "regular" solution model f = a constant. Since these two models permit only a symmetric equilibrium diagram they will not be considered further here. The simplest model that permits a nonsymmetric miscibility envelope is the so-called "subregular" solution model proposed by Hardy.1 This model gives where the Ci(T) are functions of temperature only. The same expression for f is obtained from the "linear a function" model proposed by Darken and Gurry2 and applied to miscibility-gap systems by Wriedt.3 This model requires that the a function defined by be a linear function of composition (yi is the activity coefficient of component i). This model is not purely hypothetical for it has been found2 to hold true for a number of systems. It is readily shown3 that the f(Nl, T) obtained from this model is of the form given in Eq. [2]. It will be noted that the subregular solution model contains only two parameters and hence both of them can be determined at any desired temperature below the critical temperature, Tc, for a miscibility-gap systems in the manner described previously. At T, the two constants can be determined by equating the second and third derivatives of ?Cmix with composition to zero. Another two-parameter model was proposed by Lumsden4 who set

Jan 1, 1967

By George K. Foster, Charles D. Borror

THE Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest openpit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. THE ORE BODY The ore body is a serpentinized peridotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur perpendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber [ ]

Jan 1, 1946

By O. D. Sherby, J. E. Dorn

For elevated temperature-constant load creep tests of a solid solution alloys, the creep strain is a function of a temperature-compensated time parameter 0 = je H/RT dt. The activation energy H is equal to o constant of about 36,000 cal per mol. The substructures resulting from a given creep stress condition are functions of the creep strain independent of temperature. Each new creep stress gives a new unique set of grain substructures; this is one of the factors responsible for the failure of the mechanical equation of state for creep. IN this report an attempt is made to correlate the creep properties of dilute a: solid solutions in aluminum with the subgrain structures that are developed during creep. The possibilities of such correlations have already been suggested by Wood et al. and others1-" who demonstrated that the subgrain structures are functions of the creep stress, creep strain, rate of creep, and temperature. Investigations by Sherby and Dorn' have shown that the creep strain, E, at constant load for dilute a solid solutions of aluminum is given by the functional relationship: e = f(8,u,) [1] where: 0 equals te-AH/RT = temperature-compensated time; t, time; AH, activation energy, - 35,800 cal per mol; R, gas constant; T, absolute temperature, above 400°K; and u,, initial creep stress. Consequently, it was anticipated that the subgrain structure that develops during a constant load creep test should also correlate with any two of the three significant variables C, 8, and Another possible correlation between the subgrain structure and the creep variables is obtained by differentiating Eq. 1 with respect to time, whence the creep rate, 2, becomes: = (2L) (2) =f (, u,) e-AHRT [2] or: e = F (c e H/RT, 0) [3] For the minimum creep rate, ;,, 8 is solely a function of U, as revealed by Eq. 1. Consequently, at the minimum creep rate Eq. 3 reduces to: = F (eAH/RT) [41 Correlations between U, and i, eAH/RT were found valid for solid solution alloys of aluminum where AH was a constant of about 35,800 cal per mol. The parameter ;, eH/RT is identical to the Zener-Hollo-mon parameter8," used by them in evaluating the tensile properties of copper and other metals. Eq. 4 suggests that the subgrain structure developed during secondary creep might be correlatable with either of the two variables 2, e H/RT or u,. Some of the solid solution aluminum alloys which were discussed in an earlier report' were also used in the present investigation. Sheets of these alloys were homogenized, cold rolled from 0.100 to 0.070 in. in thickness and then recrystallized to about the same grain size. Their chemical composition and grain size are recorded in Table I. Creep specimens were selected with their tensile axes in the rolling direction. The details for creep testing have been described10 and will not be repeated here. All creep tests were performed under constant load conditions. Experimental Results and Discussion Metallographic Structure of Creep Specimens: In order to obtain a preliminary concept of creep on the metallographic structure of high purity aluminum, the various ruptured specimens previously used to obtain the creep data for pure aluminum were polished and etched electrolytically in a dilute solution of fluoroboric acid. Oblique illumination was used to reveal the substructures which, for convenience, are shown in correlation with the vs. ;, eH/RT curve in Fig. 1. It is necessary to emphasize that the data for the curve refer to the various secondary stages of creep whereas the micrographs refer to the fractured creep specimens. Nevertheless a regular and systematic correlation is observed between E, eAH/RT (or the creep stress) and the micro-structure at fracture. For In (e, eAH/RT) = 42.3, which refers to creep at a high creep rate and a low creep temperature, the fractured aluminum specimen, as shown by the micrograph in the upper right-hand corner of Fig. 1, exhibited extensive deforma-

Jan 1, 1954

By Thomas C. Patton, Eric S. Cheney

L-D gold mine is 3 miles south of Wenatchee, central Washington. Recognition of locally mappable conglomerates, sandstones, and shales within the Paleocene (?) Swauk formation led to the discovery that the known epithermal gold mineraliza¬tion is limited to a previously unknown imbricate thrust zone of unknown displace¬ment cutting the open folds o f the area. Hypabyssal intrusions also are most nu¬merous along the trace of the thrust faults. Yakima basalt of Miocene age uncon¬formably overlies the Swauk formation, thrust faults, and the intrusions. The L-D mine is in a northwesterly trending imbricate fault block of nearly vertical strata. Microscopic native gold, electrum, and naumannite occur in quartz veins and as low¬grade disseminations in the well-silicified portions of arkosic sandstones. Fault gouge on the "footwall fissure" limits ore to the hanging-wall block of the fault. Epithermal mineralization and alteration are spatially related to the nearby intrusions. Right lateral north-south faults offset the ore a maximum of 300-400 ft along any one fault. From 1949 until January 1967, when the L-D mine closed, 1,036,572 dry tons of ore valued at $14,962,305 and averaging 0.396 oz Au per ton and 0.607 oz Ag per ton were mined. Recognition of the structural control of the mineralization and altera¬tion within the Swauk formation suggests several areas within and outside of the mine that warrant further exploration. For example, the high-angle faults, imbricate thrusts, and the intrusions of this area are on strike with similar features along the major Entiat fault zone 10 miles to the northwest. The L-D gold mine (previously called Squilchuck, Wenatchee, Golden King, Gold King, and Lovitt) is located in Squilchuck Canyon about three miles south of Wenatchee, Chelan County, Wash. (Fig. 1) on the eastern edge of the Cascade Mountains. The major stratigraphic unit in the area is the nonmarine early Tertiary Swauk formation, which is predominantly com¬posed of arkosic sandstone. The lack of laterally per¬sistent units and the paucity of outcrops heretofore have precluded all but the grossest subdivision of the Swauk.' As a result, the true significance of the open folds in the Wenatchee area was not recognized, and although the geology within the mine was known, the structural setting of the mine was virtually unknown. During the present investigation, several locally map¬pable units were discovered within the Swauk which, in conjunction with mine maps, indicate an imbricate thrust zone. The epithermal gold mineralization, most of the hypabyssal intrusions, and the zones of hydrother¬mal alteration are located within or near this thrust zone. The purpose of this paper is to: (1) to describe this structural setting, rather than the detailed mine geology already presented by Lovitt and Skerl,2 and (2) to sug¬gest that from an exploration standpoint, this struc¬tural setting may be repeated in areas inside and outside of the mine area. Stratigraphy and Structure of the Swauk Formation General: The Swauk formation contains three distinct lithologies. Typical Swauk sandstone is gray on fresh surfaces, poorly sorted, weathers tan, and is cross¬bedded; it consists of 40-60% quartz, 20-40% feldspar, and up to 10% muscovite and biotite 9 The typical shale is gray to dark brown, very soft, and interbedded with silty sandstones; sharp contacts exist between the

Jan 1, 1972

By D. L. Creighton, S. A. Hoenig

The field-emission microscope has been adapted for the study of microcrack growth during the early stages of fracture in metal wires. Cracks as small as 6 1 in length can be detected and their growth can be followed to specimen failure. The system is quite useful in searching for microcracks since only sharp-edged surface defects will emit electrons under the experimental conditions. THE conditions leading to brittle fracture were discussed a number of years ago by Griffith1 and the term Griffith Cracks is often used for the small surface cracks which are responsible for brittle fracture. Griffith's theory has been modified by stroh2 and more recent results on metals are discussed by Allen,3 pp. 123-40. At present the phenomenon is not completely understood but there is general agreement that at least in certain materials the sequence leading to brittle fracture involves several stages. The initial microcracks are present because of cooling or working stresses, Hahn et al.,3 p. 95. When a stress is applied to the specimen the cracks grow slowly until the release of stored elastic energy is large enough to accelerate the crack and provide the necessary surface energy for crack growth. At this point the growth rate appears to increase rapidly to some new equilibrium velocity, and failure occurs. Since the microcracks are usually about the size of a single metallic grain (Ref. 3, p. 99) it is not easy to find them and it is very difficult to follow their growth under stress. This paper will report on the use of a cylindrical field-emission microscope for observation of the formation and growth of microcracks. I) THE FIELD-EMISSION MICROSCOPE The field-emission microscope (FEM) has a high magnification and resolution and is almost uniquely suited for observations of microcracks. Since the FEM is relatively new as a metallurgical instrument, a short description will be given here. Normally metals at room temperature do not emit electrons; however in the presence of a strong electric-field gradient, electrons can tunnel out through the reduced potential barrier. Since this tunneling is a function of the local field gradient and the local work function, the emitted electrons can be used to produce a highly magnified image of the surface by allowing them to strike a phosphor screen. Because the electron emission is dependent upon the local field gradient, smooth surfaces emit few electrons except at very high fields. On the other hand cracks, extrusions, or other surface defects, having sharp edges, emit strongly since the field gradient is very high in the vicinity of these defects. This indicates that the FEM should be most useful for detection of microcracks on otherwise smooth surfaces. A field-emission microscope was first used by Muller4 in 1936 for observation of metal surfaces, and recent reviews have been given by Muller5 and Gomer.6 The instrument has been used for metallurgical studies in the area of surface diffusion,= recrystallization,7 and grain growth 8 (Ref. 8 is directed specifically at metallurgists). In the work of Muller4,5 and Gomer 6 the specimen was in the form of a sharp metal point at the center of a phosphor-coated glais sphere. The impact of the emitted electrons on the phosphor produced a highly magnified image of the specimens. Such a system is not practical for applying a controlled stress to the specimen and a cylindrical geometry has been used in this investigation. This allowed the application of a controlled tensile stress to the wire specimen. Normally a cylindrical FEM geometry produces magnification only in the radial direction. This is the case because a smooth wire at the center of a cylinder produces a purely radial electrical field. However, if there is a break in the smooth surface of the inner cylinder, the field near the break becomes three-dimensional and the area of the break is highly magnified. The reason for this is clear if it is recalled that the field gradient depends on the relative radii of the inner and outer cylinders; if a crack forms, its edge radii are of atomic dimensions and a very high field gradient is formed near these crack edges. Since the electrons receive most of their acceleration near the crack edge and are always traveling perpendicular to the field lines, they tend to spread out and produce the magnified image observed in the cylindrical field-emission microscope. 11) BRITTLE-FRACTURE STUDIES A) Experimental Apparatus. The geometrical arrangement chosen was that used earlier by Gifford

Jan 1, 1965

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production; and to produce electricity. Because it is our nation's most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health arid environmental goals are rapidly emerging. These technologies will allow coal's use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981

By Jack Green

Within three major tectonic time frames of earth history: Microplate (±3.8 - ±2.6 billion years), intraplate (±2.6 - ±1.3 b.y.), and macroplate (=1.3 b.y. - present), precious - metal deposits are confined to specific structural, depositional and physico-chemical environments. Precambrian primary gold deposits are localized in two microplate greenstone episodes (±3.7 and ±2.7 b.y.); secondary gold in Witwatersrand placers (±2.6 b.y.). Precambrian primary platinum group metals are in anorthositic facies of layered mafic intrusions (±2.8, ±1.8 and ±1.0 b.y.). Most radioisotope mineral dates cluster - at these times and are coincident with inflections on polar wandering curves. These coincidences may reflect episodicity in lunar tidal disruptions and global deceleration effects in crust and outer core during micro- and intra- plate phases. Macroplate tectonics and an oxygenated atmosphere created favorable conditions for strata-hosted and plate suture gold and silver deposits. "Black smokers" at constructive plate margins and calc-alkalic calderas at destructive plate margins are loci for hydrothermal gold and silver.

Jan 1, 1984

"NAME…""Utah"" is derived from the name of the Indian tribe, variously spelled ""Yuta, “Ute"" ""Youta,"" ""Uta,"" ""Eutaw,"" and finally ""Utah."" It means ""in the tops of the mountains,"" or ""on the heights."" The state emblem is the ""Beehive,"" typical of industry. State nickname is ""Beehive State.""AREA…Utah is the tenth state in area. It contains 84,990 square miles, of which 2,806 miles are water. When admitted as a territory in 1850, Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.TOPOGRAPHY…Utah is generally mountainous, with several main ranges and also detached groups of mountains. The valleys are broad and level. The mean altitude of the state is 6,100 feet above sea level, which makes the state the third highest of the Union. The highest point in Utah is King's Peak (13,498) in the Uinta range. The lowest point is Beaverdam Creek (2,000) in Washington county.CLIMATE…The climate is diversified between mild temperate in the northern portion to semitropical in the southern portion. There are four distinct seasons. Snowfall is heavy at the greater altitudes and rare in the southern portion. Rainfall is moderate throughout the state. Extremes of heat and cold are unusual."

Jan 1, 1925

By F. Twyman, D. M. Smith

Those chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates may be checked as often as desired. If, possessing these advantages, the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards 19cientific Paper No. 444. The Development of Analysis by Spectrogbaphy Fig. 1 shows, by means of photographs taken with a quartz spectro-graph, what a valuable region of the spectrum is excluded if one has a visual instrument only. Wave length 4023 is about the end of the visible spectrum, the region from 3800 to 1854 being invisible. It is easy to understand then how it is that the vigorous resuscitation of spectrum analysis which has commenced in the last few years has been associated with the use of the quartz spectrograph; notwithstanding that the most useful instrument for the general inorganic chemist to have at his elbow, after the balance, is a good visual spectrometer.(1) 1 The revival of spectrum analysis is to be attributed chiefly to the work of W. N. Hartley with his co-workers, and to A. de Gramont. Hartley,

John Duer Irving, who left his post as Professor of Economic Geology at the Sheffield Scientific School, New Haven, Conn., to join the Eleventh Regiment of Engineers shortly after the declaration of war, died in France, July 26, 1918, from an attack of pneumonia. Through the initiative of Mr. Benjamin B. Lawrence, a memorial service to Captain Irving was held at St. Paul's Chapel, Columbia University, on Sunday afternoon, August 4, which was' attended by members of Captain Irving's family, and about four hundred of his friends from Columbia, Yale, the American Institute of Mining Engineers and the Association of the 11th Regiment of Engineers. Professor James F. Kemp delivered the memorial address, and has prepared for the Institute the following account of Captain Irving's life, Professor Kemp and Captain Irving having been associated on the most intimate terms for a number of years. , The war has brought home to friends and kin in the western shores of thc Atlantic many losses whose suddenness has the shock of a blow. Many more will follow, but none can leave a sharper sense of regret than the news that the keen and productive mind; the inspiring teacher; the successful and considerate editor, the fine, true man and friend had all passed away when John Duer Irving made the final great gift to the service of his country, in the cause of decency and right. In the closing days of July, the cable brought the tidings that toward midnight on the twentieth of the month pneumonia had proved too great a tax upon one already worn by excessive labors. John Duer Irving was born in Madison, Wis., August 18, 1874. His father, Roland Duer Irving, was at the time professor of geology, mineralogy and metallurgy in the State University of Wisconsin.' Roland . Irving, the father, had entered Columbia College in 1863, but trouble with his eyes compelled him to suspend his studies in the classical course in his sophomore year, and to replace study with some months of life and travel in England. Ultimately his eyes became stronger, and he entered the School of Mincs, completing the course for the degree of Engineer of Mines in 1869, with the third class graduated. The class of eleven contained other future geologists. It numbered on its roll Henry Newton and Walter P. Jenney of the early survey of the Black Hills, where John, future son of Roland, was in the course of years to make his doctor's dissertation, and with its publication his really serious entrance into the profession. Roland Irving was a favorite student of Professor J. S. Newberry, affectionately known to all of his students as "Uncle John," and after some experience in mining and smelting in Pennsylvania and New Jersey, joined the Ohio Survey under Dr. Newberry. The work in Ohio was largely performed during the vacations of the University of Wisconsin, to whose chair Roland Irving was called in 1870. Later, his residence in Wisconsin led to two events of prime importance in the history of American geology. He began the study of the Gogebic iron range and caught the clue to the origin and stratigraphy of the iron ores of all the Lake Superior ranges; and he later undertook the mapping and description of the copper-bearing rocks of the Lake Superior basin. The formative years of the son, John, were passed in a home where the father.

Jan 1, 1920

From the beginning to the end, the attendance and enthusiasm of the 119th meeting, which was held in New York, Feb. 17 to 20 surpassed all expectations. Besides the ten technical sessions, one of which was in conjunction with the American Institute of Electrical Engineering and one a session of the National Research Council, there were two memorial meetings, one for Dr. Raymond and one for the members who died in service; two joint sessions with the Canadian Mining Institute; and a meeting devoted to pictures of copper mining, milling, and smelting. Of the 732 persons registered, 119 registered in the Institute of Metals Division. Monday's sessions were devoted to the problems of industrial organization, the Institute of Metals Division, and to petroleum and gas. Among the special features of these sessions were the topical discussions on housing and. Americanization. Americanization, too, was the topic for discussion by the Woman's Auxiliary Wednesday morning. On Tuesday, nearly 100-members of the Canadian Mining Institute were present to discuss the possibility of bringing about uniform mining laws for the United States, Canada, and Mexico, to obviate the maintaining separate legal departments and managerial forces for the several countries; and to avoid the confusion which, it is said, has led to a duplication of effort and has sometimes created a barrier to international cooperation in mining. Among the Canadian delegation were D. B.

Jan 3, 1919

By Arthur Foote

AT THE end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping Southwest, or, exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North. Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a North-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly.

Jan 1, 1930

E1 Teniente made blockcaving look easy. Ore rolling out the Teniente 5 level has the appearance of nicely screened riprap ready for road dressing. Actually it has been mostly size-reduced by nature abetted along the way by the occasional nudge of a double jack wielded by a buitrero (grizzly-man). It is the famous upside-down mine at Sewell, where the ore flow is down and the people flow is up. Sewell (rhymes with jewel) is the impossible cluster of dwellings clinging to a high Andean spur where 13,000 inhabitants find that staircases must substitute for sidewalks. There is no mining man who is not familiar with the picture of Sewell-by day a pyramid of barracks huddled on the high ground out of harm's way and by night a surprising Christmas tree against the mountain top. Until April 1967, Kennecott's Braden Copper Co. rocked along producing a not inconsequential amount of copper, 180,000 tpy (all tonnages cited here are short tons), attributable to its not unspectacular mountaineering and engineering achievements. These latter included expertness in building avalanche-control fencing; operation of a 35,000-tpd concentrator on the Sewell mountain spur; a spectacular aerial tramway to move 1600 tpd of concentrates to the smelter at Caletones, and occasionally to provision Sewell when snow blocks the road; a cliff hanger of a railroad 43 miles down to the rich bottom land at Rancagua; and last but not least, a 40-mile tailing launder that sweeps across deep valleys on trestles that rival those of the Romans.

Jan 11, 1969

By B. Trentini

In the spectacular development of pure oxygen steel-making, the process using the vertical lance converter LD, is at the present time the most widely employed. Proper control of slag composition during the steel-making process appears to be essential in achieving satisfactory blowing from both the metallic yield and metallurgical points of view. The paper illustrates the primary importance of the presence of a large quantity of metal droplets in the slag during the process. In the case of both phosphorus and hematite pig iron, it can be deduced from the phase diagrams and confirmed by experimentation that nonhomogeneous slags are one of the causes of slag overflowing during the blow. The problem is however a complex one and further physicochemical studies appear necessary. Finally, the new continuous steelmakingprocess developed by IRSID is described. PEOPLE who knew Henri Marion Howe have said that he took great pleasure in speculating on the future of metallurgical processes. It is therefore not inappropriate to devote, in his memory, some description and discussion to processes unknown to the world of his time, in particular oxygen steelmaking and continuous steelmaking. The first industrial application to steelmaking of tonnage oxygen produced by air liquefaction was made in Germany just before the war and consisted in enriching the air blown through the bottom of a basic Begsemer converter in order to melt a higher proportion of scrap and to produce steels with lower nitrogen content than is achieved with conventional practice. While this process was being developed after the war, mostly in Western Europe, steelmakers were becoming increasingly familiar with the technique of blowing pure oxygen from the top, first by means of consumable steel pipes, with or without refractory shielding, and later by water-cooled lances, designed for the purpose and affording longer life. The field was then open for the wide use of pure oxygen in steelmaking, either in existing processes such as open-hearth or electric furnace, or in new processes. These new processes can be broadly classified according to the category of furnace employed. In the case of the vertical converter taken as the first category, bottom-blowing of pure oxygen causes extremely rapid wear of the refractory tuyeres, and although various expedients have been tried to overcome this drawback (such as mixing oxygen with CO2 or H2O or using high pressure oxygen), they have had to be abandoned. The solution for vertical converters has been found in top-blowing with a vertical water-cooled lance; this is known as the LD process or basic oxygen converter process.

Jan 1, 1969

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By C. E. Sims, H. M. Banta, S. L. Hoyt

OVER the past few years, metallic arc welding has been extended to steels of the hardenable type. As compared with other methods of fabrication, production has been facilitated, service performance frequently has been improved, and the overall results have been so favorable that engineers and production men have placed great emphasis on this application of welding. The metallurgist and welding engineer, however, have been confronted with new problems, since, for one reason, the harder steels are more apt to crack and special precautions must be taken if sound joints are to be procured. Some of the factors that are pertinent to this problem are metallurgical, and it is an object of this contribution to discuss steel manufacture and processing methods and to show how their control assists in reducing the hazard of cracking. By this time, the problem of cracking specifically underbead cracking, or "hard cracks," or parent-metal cracks-is well known, and a large amount of work has been published, both here and abroad, dealing with this subject.1 The tests described are made under restraint to facilitate cracking and, are so designed that a semiquantitative, or at least a relative, value of the cracking tendency is obtained. As one would expect, it has been reported that the incidence of cracking increases with the carbon and alloy content of the steel. More specifically, the cracking tendency is said to increase with the hardenability of the steel, though it is now recognized that the situation is not so simple. The phenomenon itself, on the other hand, has been but loosely described, and it is in only broad generalizations that this cracking has been related to steel metallurgy. Thus, while it has been abundantly demonstrated that the hardenable aircraft steel, S.A.E. 4130, must tend to crack when arc-welded, the problem still remains of why two lots of the same composition and the same hardenability can vary so greatly in cracking tendency, or what it is about the prior metallurgical history that so strongly affects the results. Further, while the efficacy of preheating and postheating in preventing cracking is recognized and utilized in production, the mechanism by which they function seems not to have been described. These points are thought to be significant in the production of steel for fabrication by metallic arc welding and, hence, of interest to mill and process metallurgists and welding engineers. Consequently, it is another object of this paper to discuss the mechanism of parent-metal cracking, including the influence of the condition of the steel and the control of cracking by manipulation of the time-temperature conditions during and after welding. A new method of rating the cracking. tendency is also discussed, and the results of the test are related to steel composition and structure or prior history. The work to be described was the outgrowth of work in 1940-41 at Battelle Memorial Institute 0n two projects, one

Jan 1, 1945

By D. R. Uhlmann, T. P. Seward, K. A. Jackson, J. D. Hunt

microscopic ohservations on alloys of organic trzaterials show that dendrite arms can melt off under normal conditiorzs of growth. This occurs because of the interactiorz of&apos; heat and matter fluxes during dendritic growth. The re melting occurs where the den-drite arms are joined onto the main deizclrite sterrz. Many detached crystals can be produced in this fashion. It is postulated that this remelting phenornenon occurs in metal alloys, giving rise to the equi-axed region in castings. Experiments peyformed orr castings of transparent materials support remelting as a primary source of detached crystals. Ob~ervations an equiaxed tones in metal castings are discussed in terms of this and other mechanisms. It is concluded that the partial remelting of dendrites is on important mechanisnl for producing the equiaxed regions in castings. THE freezing of a casting can be divided into three regions: a chill zone formed near the mold wall, a columnar region, and a third region, at the center of the casting, which is called the equiaxed zone. The origin of the grains that comprise the equiaxed region is the subject of this paper. We will first outline the mechanisms which have been proposed to account for the origin of the equiaxed region and discuss some recent experiments which cannot be explained by these theories. We will then present some microscopic observations of dendritic growth which have led us to conclude that the equiaxed zone in castings can arise from partial remelting of dendrites. This proposal is supported by observations on transparent castings. Finally, we will discuss several observations on metal castings which could not be explained previously, and which can be accounted for by the present proposal. Previous Mechanisms. Winegard and Chalmers3 pointed out that the molten central region of an ingot could be constitutionally supercooled, because of the solute layer at the growing interface. In this supercooled region, nucleation on particles could occur, giving rise to the equiaxed crystals. Another mechanism has also been suggested,4y5 that the nuclei originate in the chill zone then float or are carried by convection to the center of the casting, where they grow to produce equiaxed crystals. In this case, all the crystals nucleate immediately on casting, so this mechanism will be termed "big-bang" nucleation. Walker&apos;s Experiments. J. L. Walker has made observations on the solidification of nickel and Ni-Cu alloys which cannot be accounted for by either of the above mechanisms. In studying the grain size resulting from freezing of nickel at various undercoolings, walker6 found that at large undercoolings the grain size was small, due to mechanical nucleation, as discussed by walker7 and Horvay.&apos; At small undercoolings, the grain size was large, and the growth dendritic. In Ni-Cu alloys, however, for initial undercoolings starting from just below the melting point and extending for a hundred or so degrees of undercooling, fine grains were also observed. Samples were undercooled 200 Centigrade degrees without nucleating, and were then heated 130 Centigrade degrees so that the undercooling was 70 Centigrade degrees, and nucleated. The samples had a small grain size, indicating multiple nucleation. There were no heterogeneous nuclei in the liquid which could operate at the temperature of growth. Constitutional supercooling could not have been greater than the supercooling of the initial melt, since the temperature rose as the freezing continued. walker -as also shown that a Ni-Cu alloy which can be undercooled to below its solidus will produce typical columnar and equiaxed regions when cast into a cold mold. This alloy could not reach a temperature below its solidus by constitutional supercooling. It could not, therefore, have nucleated heterogeneously. Neither the big-bang mechanism nor the Winegard-Chalmers mechanism can account for the fine grain

Jan 1, 1967

By R. W. Jenkins, O. J. Neslage

The need for mechanized drilling to decrease mining costs has resulted in the development of the jumbo from column-and-bar drill carriages to hydraulically controlled jib jumbos. Resultant savings from use of improved jumbos have been high enough usually to retire the machinery investment within a year. The jib jumbo unit has been applied successfully to development and preparation programs and flat-bedded stopes, and an even wider field is forecast for its use.

Jan 1, 1950