Search Documents

By J. T. Norton, N. J. Grant, I. S., Servi

Coarse grained high purity aluminum was tested in creep at temperatures of 400° to 1200°F to develop subgrain structures. Measurements of subgrain size, distribution, and rotation were made from X-ray diffraction patterns. Subgrain size and distribution were checked metallographically and the size was compared with average slip band spacing. The slip family was determined for several specimens. THE interest and research recently evident abroad in the role of subgrain formation and polygon-ization as a contribution to the creep of metals at elevated temperatures is deserving of greater attention in this country. Such metallic subgrains can be defined as macroblocks existing within the grains. The general observation has been that the macro-blocks which belong to the same grain have a maximum difference in orientation of a few degrees. In spite of the considerable amount of work that has been done since Jenkins and Mellorl observed the "division of existing crystals into smaller units when deformation occurs at an annealing temperature," the subject of subgrain formation is only now receiving truly active discussion and investigation. The existence of subgrains has been revealed by metallographic methods, as in the work of Jenkins and Mellor,1 and by X-ray methods, first applied to this problem by Homes.' Hirst3 and Calnan and Burns4 applied the back-reflection Laue technique to the study of coarse grained specimens. Wood et al.5 and Greenough and Smith' examined the ring obtained with a back-reflection camera for the study of fine grained specimens. In addition to the above, the transmission technique was used by Wood.6 A special technique was developed by Guinier and Tennevin8 in order to improve the resolution. Metallographically, the subgrains have been observed directly on the surface of deformed specimens by Wood et al.,3 or have been made evident on repolished surfaces by applying a suitable etching reagent. The latter technique, first suggested by Lacombe and Beaujard,9 was then improved by Wyon and Crussard.10 Subgrains can be formed in single crystals after small amounts of bending followed by heating after this cold work, or during deformation at elevated temperatures. The first phenomenon was analyzed by Cahn11 for the simple case of pure bending followed by annealing. Cahn suggested a mechanism of subgrain formation based on the dislocation theory and called this phenomenon "polygonization." He extended this mechanism to the more complex case of local bending, such as the bending which may occur when a polycrystalline specimen is deformed in tension. Cahn's suggestion was later found quite consistent with the results obtained by Dunn and Daniels." An explanation has been presented recently regarding the formation of subgrains during deformation at elevated temperatures by Chang and Grant.'" In general, there are two schools of thought on the subject. One, according to Wood et al.,5 is that subgrain formation is a mechanism of deformation which is operative under certain conditions in the same way that the slip process is the mechanism of deformation which is operative under other conditions. The boundaries between the subgrains undergo a viscous flow which contributes substantially to the deformation of the material. The second, according to Cahn,13 Wyon and Crussard,10 and Chang and Grant,18 is that subgrain formation is the effect of simultaneous deformation and annealing and is,

Jan 1, 1953

By T. R. Wright

IN few mining regions in the world are the ores so varied and complex as in the Andes of central Peru. Consequently, in few localities is one company engaged in so many and such diverse metallurgical operations as the Cerro de Pasco Copper Corp. Concurrent with the mining of complex lead-zinc ores in Peru, and the consequent expansion of the Corporation's metallurgical activities, a department of metallurgical research was established in 1927 at La Orova. Facilities were provided for research in ore dressing, hydronivtallurgy pyrometallurgy, electrometallurgy, and analytical chemistry. In addition to laboratories. various pilot plants were built, including a concentrator, leaching plant, "by-product" smelter, and electrolytic refineries. These pilot plants are not diminutive units; they are designed and equipped as semicommercial plants for operation on a continuous 24-hour basis thus assuring the duplication of pilot plant results in actual practice. In general, the sequence in the development of metallurgical operations hasbeen as follows: (1) investigations in the laboratory to determine the most effective and economical method of treatment; (2) continuation of the research project on a pilot-plant scale when the evaluation of the laboratory

Jan 1, 1945

By Kjell Lidin, Christer Nordström

INTRODUCTION LKAB produces iron ore in several mines in northern Sweden, and has been doing so for nearly 100 years. Total production to date is 600 million tonnes of finished products of various kinds (pellets, lump ore, fines). Close to 400 million tonnes have been produced by sublevel caving. This method has been the company's standard method for more than 20 years. A review of the development of equipment over the past 15 years and an outlook up to about 1990 leads to the following general re- flections concerning probable trends. Trends for all equipment are increasing precision and stricter environmental requirements will necessitate cabs, remote control etc to an increasing extent. Conventional sublevel caving can be broken down into the following unit operations: 1. Planning incl prospecting drilling. 2. Horizontal drilling. 3. Fan drilling. 4. Charging and blasting. 5. Loading and haulage at sublevels. 6. Ore drawing in chutes. 7. Rock reinforcement. 8. Production service. This lecture will deal in brief with each of these unit operations and the trends we are experiencing for them. A number of slides illustrating equipment

Jan 1, 1981

By F. C. Stanford

The work of an engineer is to direct natural forces so that the: bring about the results that he wishes to secure. Heretofore he ha concerned himself chiefly with physical forces and inanimate objects until he has secured a truly marvelous degree of control over them The great problem of the present age is to secure a like degree of know1 edge and control of the human factor. Progress has already been made along this line, but it is only a beginning. Wilhelm Ostwald says tha scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to main tain a high average in prophecy. In short, 'the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essentia need of the period is for more brains; if we only had sufficient knowledg and sagacity we could not only solve all difficulties, but prevent then from arising. This generalization holds good for an industrial organization. Th most vital need of the management is for more brains. The logica course for an engineer in charge of an industrial organization is, therefore to direct whatever forces may be at his command toward the development training, and guiding of all the brains in his organization. This is easie said than done, for it involves the carrying on toward two objective: the maximum of productive work, and the development of the individual who perform it. This is essentially like the rebuilding and enlarging of plant, keeping it in full operation the while. On the other hand, if th aim is merely for maximum production from an organization, withou offering opportunity for development, the final outcome will necessari be like that of a plant that is driven at full capacity without stoppin for repairs or improvements; it eventually becomes so run down th either a complete rebuilding is necessary or else it has to be abandone

Jan 1, 1918

By Richard W. Smith

Kyanite, long known to occur in Georgia, did not excite coimmercial interest until about 1930. Investigation1 revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumulation from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not more than a few feet. 'rile larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersharn County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habershain County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanitc-mica schist belt in Habersham and Rabun counties will bc discussed in this paper. Geology The kyanite-mica schist of Habersham and Rabun counties occurs near the northern cdge of the Piedmont Upland in metamorphic rocks of pre-Cambrian age3. These rocks probably were deposited as sedimentary

Jan 1, 1938

By Richard W. Smith

Kyanite, long known to occur in Georgia, did not excite coimmercial interest until about 1930. Investigation1 revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumulation from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not more than a few feet. 'rile larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersharn County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habershain County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanitc-mica schist belt in Habersham and Rabun counties will bc discussed in this paper. Geology The kyanite-mica schist of Habersham and Rabun counties occurs near the northern cdge of the Piedmont Upland in metamorphic rocks of pre-Cambrian age3. These rocks probably were deposited as sedimentary

Jan 1, 1938

Discussion of the paper of W. A. Forbes, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2477 to 2514.. SAMUEL K. VARNES,* Steelton, Pa.:-We have a gas-cleaning plant consisting of a, centrifugal dry dust catcher, and two rain-type wet scrubbing towers, 25 by 60 ft. each, for rough cleaning of blast-furnace gas. This plant was put in early in 1910, with the intention of cleaning gas for use in hot blast stoves and under boilers, and was so used for several months. Soon after it went into service, the blast-furnace men complained that they could not get as high blast temperatures as they had obtained when using dirty gas. It was decided to run a series of careful tests to determine if this were true and to what degree the apparent results might be affected by other conditions. About 60 tests were run, covering a period of five months, and at the end we came to the conclusion that it did not pay us to scrub the gas for stoves and boilers. The tests were all run upon a single stove, no boiler tests being made, but the conclusions of the stove tests being applied to the boilers. The furnace burden was practically the same for all the tests and averaged: Per Cent. Daquari and other hard ores 57 Nodules 13 Raw Mayari ore 25 Mill cinder and scale 5

Jan 12, 1913

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

By H. Eklund, R. T. Hukki

This article presents a simple arithmetic derivation for the relationship between sharpness of classification and circulating load, as well as world-wide industrial data which are compatible with the derived equation. It is shown that the sharpness of classification decreases with increasing circulating load. Based on the evidence available a comparison is presented between the performance of the present-day hydraulic classifiers. In a continuously operated closed circuit grinding system the tonnage and the fineness of the components may be indicated as follows: Eq. 8 expresses the relationship between sharpness of classification and circulating load in closed grinding circuits. If CL = 0, E = 100% according to the definition used. This, however, is a purely theoretical case because any apparatus to be called a classifier must produce the conventional two products. Furthermore, if CL = m, E =0%. In order to visualize the meaning of Eq. 8, the effect of factors d (fineness or percentage of under-size of classifier overflow at size x) and b (fineness or percentage of undersize of classifier sands at size x) should be studied. By the most rigid standard, factor d should be given the value of 100%. By so doing the size of classification is defined as that screen size x through which 100% of the classifier

Jan 1, 1965

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By A. T. Aldred

HIS note reports the existence of several new scandium intermetallic compounds of the A2B and AB stoichiometries where the A element is scandium and the B element is from group VIII or IB of the periodic table. Alloys were arc melted from high-purity materials using 2-g charges. Typical lot analyses for the materials used are given in Table I. Chemical analyses were not made on the alloys as there was little or no weight loss on melting. After annealing the specimens for 14 days at 600°C and water quenching, metallographic and X-ray techniques were used to determine the occurrence of the various phases. Table II lists the relevant data for the A2B phases. The Ti2Ni structure,2 has ninety-six atoms in a face-centered cubic cell, whilst the Al2Cu structure is body-centered tetragonal.3 The occurrence and stability of the various A2B type phases in transition metal alloy systems has recently been considered by Nevitt.4 The Ti2 Ni-type phases occur over a relatively narrow range of radius ratios from 1.14-1.26 with A partners mainly from the titanium group and B partners predominantly from the cobalt group. This suggests that both a favorable relative size of the atoms and a favorable electron concentration are necessary conditions for the existence of this structure type. A12Cu-type phases involving Ti group elements as A partners are formed with B partners from the cobalt and nickel groups, predominantly the latter, and have a higher radius ratio (1.27-1.29) than the Ti2Ni-type phases. The occurrence of both Sc2Pd and Sc2Co can be rationalized in terms of these considerations but SczNi is anomalous because of its high radius ratio. The radius ratios are calculated from the Goldschmidt CN12 radii and it might be postulated that the scandium atom is reduced in size in the compound. Unfortunately the apparent atomic size of scandium in the compound cannot be calculated from a knowledge of the structure and lattice dimensions. The crystal structure of the Sc2Au compound could not be identified from the powder diffraction pattern, but it is interesting to note that it is isostructural with a series of A2Au phases where A is a rare earth element.5 Pertinent information concerning the AB phases found in this investigation is given in Table 111. All the phases have the ordered bcc CsCl structure. The occurrence and stability of CsC1-type phases have recently been discussed by Dwight,7 who concludes that the relative sizes of the atoms do not appear to be a controlling factor (the radius ratios of all the known phases vary between 0.985 and 1.439) but that the occurrence of the phase is predominantly dependent on the relative positions of the A and B partners in the periodic table. As a measure of the stability of a given CsCl phase it has been customary to define a lattice contraction on alloying, DAB — dAB, where DAB is the AB interatomic spacing as calculated from the Goldschmidt CN8 radii and dAB is the AB interatomic distance in the compound (= v3/2 ao). Values of the parameter DscB -dScB for the compounds found in this investigation are given in column 5 of Table III and are plotted in Fig. 1. If the lattice contraction does in fact reflect the stability of a phase then Fig. 1 shows two very interesting trends when the position of the B partner in the periodic table is considered. Firstly, within any given group the stability increases in order on going from the first to third long period. Secondly, within any given period the stability increases in order as the B partner is taken from the copper, nickel, and cobalt groups. In the case of the second long period, the lattice contraction reaches a maximum at ScRh and then decreases to ScRu. The same trend could

Jan 1, 1962

By N. LILIENBERGS

DURING the past few years, the requirements for steel have been raised so high that soundness is more important than ever before. The old practice was to mike steel ingots of sufficiently large sections to permit a considerable reduction of area in rolling and hammering to a given size, relying on the fact that by such rolling and hammering all cavities will be squeezed together and practically eliminated. The finished sizes, if found by inspection of the surface to be faultless, were therefore pronounced to be sound. But when such steel is ?worked up,? the manufacturer is surprised and disappointed to find that it splits, or that streaks and seams make the product unmarketable. Large sections, such as rails, beams or heavy forgings, may, within certain limits, be sufficiently strong, even if the sides of the cavities are only squeezed, and not welded together. But it is well known that, in the interior of heavy articles, under certain conditions, forging may develop small streaks into large cavities. Small sections, steel for ordnance and tubes, and numberless articles in the tool-trade, always show up the defects. It may be doubted whether cavities in steel ingots can ever be completely welded. The old theory, is, that the silver-clear blow-holes, without the blue oxide, can be welded by sufficient working. They are, however, not empty, but are filled with carbonic oxide. It is admitted that the "blue" cavities, resulting from air mechanically drawn down into the mold during the casting, can never be welded, because the oxide does not melt, and there would be no escape for it if it did. The only way in which steel can be made satisfactory for the above-named particular purposes is by having it ?dead molten." But then the trouble of piping is encountered. As is well known, a pipe is the result of the contraction of

May 1, 1906

By D. L. McElroy

SAFETY in coal mining received especial attention by the public in general and the mining industry in particular during 1940 and early in 1941, owing primarily to the six explosion disasters which occurred last year with a total of 276 fatalities. This was the largest number of fatalities due to explosions in bituminous coal mines since 1928, when 347 lives were so lost. But facilities due to explosions have had a definite decreasing trend since 1907, in spite of bad years such as 1917, 1924, 1932, 1937, and 1940. Although the upswing in explosion fatalities in 1940 is lamented by all, none will admit it represents a trend and it will serve mainly to stimulate ways and means of further reducing these disasters.

Jan 1, 1941

By C. G. Rhodes, D. Kramer

High-field critical transport current density (J) measurements at 4.2 °K as a Junction of applied magnetic field (H) were made on samples of cold-rolled and annealed columbium with H parallel to J. Microscopic examination of the samples revealed a well-defined planar fiber structure produced by the cold rolling. J was found to he lower when fibers are parallel to the direction of magnetic field penetration than when they are perpendicular. This effect may he a consequence of the interaction of flux movement with fiber boundaries. THE severe changes in microstructure brought about by cold working superconductors leads to profound changes in their superconducting behavior. In particular, the ability of a superconductor to carry a transport current with zero resistance (the maximum value of this current density will be called "J" in the presence of large external magnetic fields (to be referred to as "H") is greatly influenced by the microstructure. In the case of columbium, LeBlanc and Little1 and Autler et a1.2 have observed an increase in J due to cold work. LeBlanc and Little also observed an anisotropy in J in cold-rolled columbium strips, which Hake et al.3-6 have shown to depend upon the angle between H (H ? J) and the rolling plane. An increase in J due to cold work has been found in a variety of high-field superconducting alloys3'4'7-9 as has the anisotropy effect.10 First explanations of why cold work raised J invoked the idea that dislocations carried the high-field supercurrents,8,11 since cold working drastically increases the dislocation density and presumably the number of supercurrent paths. However, recent ideas on the nature of high-field superconductivity together with new experimental evidence reveal that the bulk of certain superconductors can remain superconducting in high fields while carrying high transport currents. These later developments have been discussed by Berlin-court and Hake12 and a comprehensive review has been prepared by Berlincourt.13 According to the ideas of Gorter14 and Anderson,15 one would expect that the influence of microstructure on high-field supercurrent density will depend on tine interaction between microstructure and penetrating flux and on the direction of the Lorentz

Jan 1, 1965

By A. M. Gaudin

THE study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a, substantially definite size which depends upon the ball size 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with-all the crushers tested. 7. Different methods of crushing produce grains of different shapes.

Jan 2, 1926

By Charles Fettke

IN 1914, the officials of the Brundred Oil Corpn., faced with the problem of introducing new methods to increase production in the old and nearly depleted pools of Venango County, became interested in the Smith-Dunn (Marietta) process which was at that time being tried out in southeastern Ohio and which was already yielding very encouraging results. A license to use the process in Pennsylvania was secured from the owners of the patents. These patents were later declared invalid. The method was first used in Pennsylvania on a property consisting of about 434 acres, of which 300 are productive, at Hamilton Corners, 15 miles northeast of Oil City, in Cherry Tree and Oakland Townships, Venango County. The producing horizon is the First Sand of the Venango Group. A small oil pool was opened up in this vicinity in 1904. By July, 1916, when the compressed air was first introduced to restore pressure, the production had dropped to a point where it was no longer possible to continue profitable operation. From that time until March, 1927, over 100,000 bbl. of oil have been recovered from the tract. The property is being operated at present by the Brundred Oil Corpn. and Lux. The 1926 production, amounting to 10,650 bbl., was only 400 bbl. short of the maximum reached during any year of the 10-year period that the process has been in operation. Inasmuch as the Hamilton Corners pool is the first one in Pennsylvania in which the Marietta process was tried out, and the one in which it has been longest in continuous operation, considerable interest attaches to the results obtained. Through the courtesy of H. D. Brown and W. J: Brundred, officials of the Brundred Oil Corpn., all their data on this operation were made available to the writer in connection with an investigation of rejuvenation methods in the State for the Pennsylvania Geological Survey.

Jan 1, 1928

By Wittenau, E.

OPERATION of a pilot mill of 100 tons' daily capacity during 1930 and 1931 proved that the copper minerals of the Colorado and Clay sections of the Morenci ore body could be successfully concentrated by the flotation process. Economic conditions caused postponement of further testing work until late in 1938 when the former No. 6 Concentrator at Morenci was converted into an experimental mill of 1500 tons' daily capacity which was known as the Test Concentrator. The Test Concentrator began continuous operation on April 3. 1939, using such crushing and grinding equipment of the No. 6 Concentrator as was appropriate. Modern classifiers and certain flotation machines were installed and later other types of flotation machines, a large grate-type grinding mill. mechanical screens, a short-head cone crusher, and a disk filter were added to the test equipment. Operation was uninterrupted until Dec. 31, 1941.

Jan 1, 1942

By Samuel L. Hoyt

Cemented tungsten carbide, a product of a branch of metallurgy which has never possessed more than a relatively minor interest and importance, has recently commanded the attention of engineers, industrialists, financiers and men of business. New methods, new opportunities, new goals, never before considered, have suddenly been brought within the scope of practical realization. It is these results that attract the interest of the world, but we, as engineers and metallurgists, will have equal interest in the product itself and in that branch of metallurgy from which it comes. It seems appropriate, therefore, to speak today on Hard Metal Carbides and Cemented Tungsten Carbide, as the latter represents one of the outstanding developments of recent date in non-ferrous metallurgy. We are interested in the hard metal carbides as a group of related metallic substances and in cemented tungsten carbide as the leading representative of the metallurgy of this group. The literature of this general field is limited, and, bearing this in mind, it seems advisable to attempt to cover the field broadly and to correlate the subject matter, rather than to present a detailed account of any one of its phases. Our annual lecture lends itself admirably to this plan. The quickened interest in cemented tungsten carbide, once its potentialities were recognized, the many sides to the problem of developing the manufacture and use of this new product, and the desire to economize as much as possible in the time of development, have brought many into this work, both in this country and abroad, notably the Osram Lamp Co. and Friedrich Krupp in Germany and the General Electric Co. in this country. It would be presuming too much to attempt to speak too broadly of the present state of the art and science of the hard metal carbides and my remarks arc guided largely by the work done in the General Electric Co., and by our associates in the Carboloy Co. Even here the activities of many in these two groups have centered around the utilization of cemented tungsten carbide, which is outside the scope of this talk. To those whose work is represented in this lecture, it is my pleasant duty to acknowledge their assistance and advice. To Dr. Zay

Jan 1, 1930

By J. W. Furness

THE utilization and collection of waste materials have gone on for centuries, and have become a habit of the human race. The degree to which the salvaging of waste plays a part in a nation's industry depends largely on the availability of raw materials within the political confines of the country itself, or its ability to purchase such material from outside. When purchase is necessary careful economical use of the raw materials results. These economies, as a rule, are represented by lengthening the life of the given article as well as much re-use. For many years the steel industry of Italy and Japan has depended largely on importations of scrap, yet both are important. As long as the expenses incident to the conditioning and marketing of materials manufactured from salvaged waste are less than the cost of virgin material, the salvaged material will be re-fabricated and in many cases will compete with primary materials. One of the most obvious methods for furthering the efficient utilization of our limited mineral resources is the salvaging of mineral wastes. This method, moreover, in¬creases the available supply of a given material. If the price depends on a balance of supply and demand and the recovery from wastes enlarges. the supply, there can be no question but that it influences the sales price of primary.

Jan 1, 1931

By B. W. Howlett, M. B. Bever, Somnath Misra

The heats oj- formation at 0°C of the compounds AuSn,, AuSn2, AuSn, and the £ phase were measured in a metal -solution calorimeter with liquid tin or a liquid Sn-Bi alloy as solvent. The melting point, heat of fusion, and heat capacities near the melting point of- the compound AuSn in the solid and liquid state were measured in a constant temperature gradient calorimeter. The free energy and entropy of formation of the compound AuSn at its melting point and at 298 °K were calculated from the experimental results and published data. The heats of formation are discussed in relation to the nature of the compounds. The heat capacity below the melting point, heat of fusion, and entropy of fusion of AuSn are interpreted in terms of processes oc-curring before melting. The atomic arrangement in liquid Au-Sn alloys and the bonding in the intermediate phases of. the Au-Sn system are discussed in the light of the measured thermodynamic properties. THE available thermodynamic information on the intermediate phases in the Au-Sn system consists of the heats of formation of the compounds AuSn4, AuSn2, and AuSnly2 and of one composition of the < phase2 besides values of the heat content of the compound AuSn from 0" to 635".&apos; However, the heats of formation refer to different temperatures ringing from 90" to 450°C. Also, the reported error limits of some of the values are large and several inconsistencies are apparent. In the investigation reported here the heats of formation of the compounds AuS-, AuSnz, and AuSn and of three compositions of the < phase were determined for a single reference temperature of 0°C by liquid metal-solution calorimetry. The compound AuSn, which is the only congruently melting intermediate phase in this system, was further investigated in a constant temperature gradient calorimeter by measuring its heat of fusion, melting point, and heat capacity in the solid and liquid states near the melting point. From these data and published free energies of the liquid of composition Au~n,&apos; the free energies of formation of the compound AuSn at the melting point and at 298°K were calculated. The results shed light on the solid-liquid transition of AuSn and on the atomic bonding and state of association of gold and tin in the solid and liquid phases. 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Samples. Stoichiometric amounts of gold and tin, each 99.99+ pct pure, were melted in evacuated Vycor capsules (12 mm ID). The melts were maintained approximately 150°C above the liquidus for about 12 hr and shaken repeatedly. Samples of the compound AuSn were cooled slowly to room temperature. Melts of the other phases, all of which solidify by peritectic reactions, were transferred to the narrow end (5 mm ID) of the capsule, which was then quenched into iced brine. The solidified samples were annealed in the unopened capsules for 10 days at 30" to 50° C below the respective solidus temperatures. The absence of microsegregation and second phases was confirmed by metallographic examination. At least two batches of each composition were prepared. 1.2) Solution Calorimetry. The heats of formation were determined by liquid metal-solution calorimetry. In this technique, the difference between the heat effects on dissolution in a liquid metal, or alloy bath, of the compound and a mechanical mixture of its annealed components, adjusted for changes in composition of the bath, is the heat of formation of the compound at the temperature from which the samples are added. Details of the equipment and technique have been described."&apos; A tin bath at 300" or 350°C was used with the compounds AuSn,, AuSnz, and AuSn. The high gold content of the £ phase would have caused it to dissolve with an appreciable exothermic heat effect. In order to achieve thermal compensation, the samples were added from 0°C to a bath at 350°C consisting of 66.2 wt pct Bi (99.999+ pct pure), balance Sn (99.99+ pct pure). This solvent gives thermal compensation because gold dissolves exothermically in tin and endothermically in bismuth. The calorimeter was calibrated by adding from 0°C approximately 0.015 g-atom of the solvent.

Jan 1, 1965