Search Documents

The Bureau of Mines in the Department of the Interior is increasingly concerned with the safety and health of personnel engaged in coal-mining operations, particularly below ground. The Bureau is also concerned with improving the utilization of domestic mineral resources, and reducing the environmental impact of mineral operations. One obvious way to improve safety and minimize health hazards would be to eliminate coal mining entirely by bringing the energy value of the coal to the surface in some other way, such as by partially burning it underground to form combustible gases and bringing these gases to the surface, where their energy content can be put to use. This technique might also improve the utilization of the coal resource. ? Accordingly, the Bureau of Mines, interested in re-evaluating underground coal gasification technology in terms of current and expected conditions in the United States, requested Arthur D. Little, Inc., (ADL) to appraise the technology to determine: ? Whether the current (1971) state of the technology offers a technically feasible method for gasifying coal underground that is applicable to the reserves of bituminous and lower rank coals in the United States. ? Whether a program of research and further development of the technology could ultimately make it a technically feasible alternative to current open-pit and underground coal mining operations. ? What the nature and cost of further research and development work in the technology should be.

Jan 1, 1971

By Frederic P. Dewey

The Bureau of the Mint of the United States Treasury maintains 13 ofEces for the purchase of gold-bullion, and this paper describes an investigation to establish the reasonable differences in the assay-results at the various institutions which may be commercially allowable in the settlements between them. Beginning with the comparative assay of proof-gold at the Philadelphia mint and the Utrecht mint, which shows 0.00002 as the closest agreement now possible, nine tables of comparative results, taken from the regular work of the service, are given..These tables begin with very fine gold, produced in an electrolytic refinery, showing close agreement in the assay-results, and follow through decreasing gold fineness and increasing amounts and complexity of base metals to very impure and complex bars produced at cyanide-mills, some of which give widely-varying results. Next is given a series of results on samples, prepared and sent out to various laboratories in the service, to test the influence of different metals and various combinations upon the agreement of the assay-results ; 11 samples were sent out and each one was assayed from 44 to 71 times, making a total of 623 assays. To these ire added 107 assays of identical samples of coin-gold. On a previous occasion,' I have endeavored to show the degree of accuracy that may be expected in the ordinary everyday analysis of various materials, and on another occasion,2

Jan 1, 1910

By Mike Tracy

This section of the Handbook deals with general principles to be evaluated in the development of a mining operation. It addresses the major issues that must be examined to fully evaluate a mining venture. Of course, one of the main topics to be evaluated is mine planning, which is covered in more detail in other sections (13, 17) of the Handbook and should be referenced in mine development projects. The topics to be discussed in this introduction include equipment and supplies, infrastructure, utilities, and project management. In any of the aspects mentioned, the current existing conditions at or near the mine site must be evaluated. This will include assessment of current use of utilities, infrastructure, housing, equipment suppliers, etc., as well as anticipated growth, both in the supply aspect of these systems as well as projected usage on these systems. After full assessment of both these aspects, an evaluation must be made as to the requirements the project will place on these items. Assessment must be made as to any up-grades required to bring the project on line, what impact the project will have on existing or expanded systems, and anticipated future growth impacts on support systems not only of the project but of other surrounding industry and urban devel-opment

Jan 1, 2008

By D. T. Bergado

The uppermost subsoil profiles of the Bangkok plain can be divided into four layers, namely: weathered clay, soft clay, stiff clay, and dense sand layers. The soft Bangkok clay is a normally consolidated marine clay with built-up preconsolidation effects and overlain by a weathered crust. Up to the present, a large number of full-scale tests on excavations and pile foundations has been made by numerous investigators. Based on these results, the available data are reviewed and evaluated. The results show that for test excavations, the excess pore pressures were overpredicted by the existing theories. The vertical and lateral movements in the excavations can be predicted by the bilinear and non-linear finite elements using appropriate modulus values. Relationships among probability of failure, safety factor, and safety margin of the excavation were also obtained. In the case of pile foundations, good agreement between the measured and predicted ultimate pile capacities were obtained for long piles. The adhesion factors ranged from 0.4 to 1.0 while the average skin friction factor was found to be 0.33. The ultimate capacity of the pile was also predicted successfully by using the Dutch cone data. For lateral deflection of piles, Davisson and Gill's theory predicted well in the low deflection zone while Poulos' theory agreed well in the high deflection zone. From the probabilistic analysis of ultimate pile capacity, the probability of failure was related to the central factor of safety. The piles usually used in Bangkok area are mainly precast concrete piles

Jan 1, 2010

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

By Stephen G. Downs

PCF?, or Penetrating Cone Fracture, is a propellant-based technique for rock excavation, which has significant potential for the mechanization of narrow-vein mining. The technique is currently being developed for use in the narrow-vein flat-dipping gold and platinum deposits in South Africa in conjunction with major mining companies. The technique is also applicable to steeply dipping vein deposits, such as those found in North America, Australia and elsewhere. The implementation of PCF? in South Africa to date is reviewed and plans for the introduction of PCF? excavation in other areas are highlighted.

Oct 1, 2001

By Victor V. Verbinski

This report presents the development of a raw coal concentration sensor for hydro-transport of coal and refuse (rock) from underground mines, and the results of an international test series carried out at the Colorado School of Mines Research Institute in Golden, Colorado, the U.S. Bureau of Mines, Hydraulic Transport Research Facility in Pittsburgh, Pennsylvania, Saskatchewan Research Facility in Saskatoon, Saskatchewan, Canada, and the Steinkohlenbergbauverein Test Facility in Essen, West Germany. Test results are presented for a three-component sensor and also for the more rugged two-component (all nuclear) sensor.

Jan 1, 1988

A concise country-by-country summary of the mineral industry of Africa is presented. Reserves, resources, role of the country in the world mineral supply, and developments in the mineral industries are reviewed. The data on each country are accompanied by a map showing mineral location and transportation facilities.

Jan 1, 1976

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment such as haul trucks often account for the greatest number of fatalities in the mining industry each year. Despite previous analyses that have identified root causes and other contributing factors, there is still a need to better understand the events leading up to these types of accidents, what lessons may be learned, and what strategies can be employed to prevent fatal accidents from occurring. This study examines Naturalistic Decision Making (NDM) using the critical decision method (CDM). The CDM is a retrospective interview approach used to explore timelimited, high-stakes, decision-making. In this study the CDM is used to obtain more information about what happens prior to, during, and after a potentially fatal situation such as a near-miss event, loss of control, or minor accident involving equipment damage. Researchers captured firsthand accounts from 21 haul truck operators involved in near-miss events from mine sites of various sizes and commodities throughout the United States. These accounts provide rich and detailed narratives from the perspective of haul truck operators themselves and reveal insights into what decisions haul truck operators make, what sensory cues they perceive, and what strategies they employ during challenging and non-routine situations. Decision-related themes that emerged from the data are presented and discussed. These results, along with potential solutions offered by study participants, can help to inform future research, raise awareness about hidden hazards, and build more creative interventions and realistic training scenarios for use by the industry to address haul truck safety issues.

Feb 1, 2024

By R. Lusignea

This report describes the development of a device for the nondestructive testing of resin grouted roof bolts by means of mechanical frequency response. Various alternative methods were evaluated and the mechanical frequency response method was selected. An interactive program of design, testing, and development culminating in the current prototype instrument demonstrated the capabilities of the method and suggested potential applications of the instrument. The resin bolt testing device utilizes a swept frequency dynamic compliance measurement in the 1 to 2 kHz range which is interpreted by an electronic signal processor to give a "GO" or "NO GO? readout. Field tests have shown that the device can reliably determine the bond quality of the front half of the bolt (nearest the roof surface). Tests were carried out on both experimentally installed bolts and typical mine bolts installed by a conventional bolting machine. The development program has led to recommendations for improvement of the prototype and future development work.

Jan 1, 1979

By G. B. Glass

In 1996, 92.5% or 233 Mt (257.4 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River Coal Field. While the mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft), the thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash, and 19.98 MJ/kg (8,590 Btu/lb). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coal beds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 10.2 billion cu ft a year. This production is occurring just west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By N. E. Lehman

Cordilleran metamorphic core complexes in the southwestern United States are areas where middle to late Tertiary low-angle normal faulting has uncovered rocks that were at temperatures sufficient for mylonitization during the early part of Tertiary extensional faulting. Large-displacement low-angle normal faults that separate upper-and lower-plate rocks in metamorphic core complexes are termed detachment faults. The significance of Tertiary detachment faulting in the Basin and Range Province has only become apparent in the past 6-8 years, and the association of mineral deposits with detachment faults has only been recognized in the past few years as well. Crystalline rocks below detachment faults have typically undergone chloritic alteration and brecciation over a distance of a few to a few hundred meters below the fault surface (Fig. 1). Chloritic alteration and brecciation overprinted mylonitic fabrics formed during earlier ductile shearing along the down-dip projection of detachment faults. Rocks that underwent pre-Tertiary ductile deformation and prograde metamorphism were subjected, in rapid succession, to middle to late Tertiary mylonitization, brecciation and chloritic alteration, microbrecciation immediately adjacent to the fault, and subaerial exposure. Lower-plate rocks thus experienced rapid decompression and cooling as a result of tectonic denudation and isostatic uplift (Wernicke, 1981; Davis, 1983; Davis et al., 1986).

Jan 1, 1987

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes.Water is routed to the roof bolter fromthe main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/ m3, and during the cleaning of the dry box, the average respirable dust concentration was 1.188 mg/m3, a 60% reduction in respirable dust concentration. The quartz content of the roofmaterialwas high, ranging from 28.9 to 52.7%during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60% when cleaning the collector boxes.

Aug 26, 2020

By Shirley F. Colby

The past 40 years have seen the sand and gravel industry grow from small roadside pits and holes in farmers' back yards to giant corporations selling millions of tons of sand and gravel each year and owning plants representing huge capital investments in land and equipment. The days hen a man could "work out" his taxes by providing the materials for nearby roads are gone forever. In addition to the hundreds of privately owned and operated plants, Government agencies operate sand and gravel pits and plants to supply aggregates for the tremendous road-building and public-works programs in progress during the past few years. EXPANDING PRODUCTION In 1940 the send and gravel industry produced almost a quarter of a billion short tons valued at more than 110 million dollars. This compares with less than 2 million short tons worth 1 1/2 million dollars produced in 1902. The practice of screening sand and throwing away the gravel in the early days of the industry's growth has stopped, and in 1940 gravel constituted two-thirds of the total production. In 1906, the first year in which sand and gravel were reported separately gravel accounted for only one-

Jan 1, 1942

By William H. Bassett

RECENTLY it has become the custom of retiring presidents to talk of the relations of the Institute to its membership and its constituency- and it seems a good precedent to follow. Past-president Smith reviewed our relations to materials and to society in general. Mr. Bradley spoke of the value and use of our publications and of our educational duties. My message will be in regard to the coordination of our various groups of member interests and of service to industry. This Institute has, within its organization, four divisions and fourteen technical committees--each interested in a separate put very definite subject, and each covering a phase of mining engineering interest. These vary from geology and the geophysical methods of prospecting, to the physics of the structure of metals, truly "from the mine to the consumer"-from the preparation for mining to the final use of that which has been mined.

Jan 1, 1931

By N. Greninger

The Bureau of Mines conducted a laboratory study of the measurement of the water and rock dust (RD) contents of synthetic mine-type coal dust (CD) mixtures using a commercial unit for measuring water content and several prototype radiometric units for measuring the RD content. The RD content ranged from 50 to 100 wt pct and the added water (AW) ranged from 0 to 15 wt pct. The total water (TW) content (intrinsic (IW) and AW) of a small dust sample could be readily measured automatically by essentially untrained personnel using a commercial unit. The RD content of a sample containing only IW could readily be measured by moderately trained personnel using several radiometric units. With gamma-ray devices, about 300 g of sample is needed. With the improved beta-ray device, about 25 g of sample is needed. With dry mine dust samples, the estimated RD error range for gamma-ray devices is 0.8 to 2.3 pct and 0.5 to 1.0 pct for beta-ray devices. However, the radiometric measurement of RD content was questionable if the dust mixture also contained AW or if it was uncertain whether the dust mixture contained AW.

Jan 1, 1988

By D. A. Hill

A survey of the literature on ELF and VLF atmospheric noise has been made. Most measurements have concentrated on the vertical electric field and the horizontal magnetic field rather than the vertical magnetic field which is of interest in transmission between horizontal loops. The limited vertical magnetic field data indicates that the vertical component is generally 10 to 20 dB below the horizontal component. Three laterally inhomogeneous earth models have been analyzed for conversion of horizontal to vertical magnetic field. The rough surface model examines surface effects, the inhomogeneous thin sheet model treats volume effects, and the buried cylinder model treats localized man-made effects. All three models predict the possibility of significant conversion from horizontal to vertical magnetic field. A thin sheet model has also been used to examine transmission from a buried magnetic dipole source. It is found that the predicted fields more nearly model the measured data than does the homogeneous half-space model.

Jan 1, 1982

The Bureau of Mines is responsible for a broad spectrum of programs for meeting the diverse and changing mineral resource needs of the Nation. These programs are managed by the Director and two Deputy Directors, who formulate general policy and program direction from the Washington, D.C., headquarters. Bureau program activities are classified into two major functions, minerals research and minerals information and analysis. A senior advisory staff, consisting of the Chief Staff Officer and Chief Scientist, provides advice and consultation to the Director on a wide range of scientific and technical matters and acts on behalf of the Director to maintain liaison with other government agencies, both foreign and domestic, mineral industries, and professional societies. The Minerals Research Directorate Technological research and development in minerals have long been cornerstones of the Bureau of Mines. The Minerals Research Directorate performs this work. Re-search functions cover the extraction, processing, use, reuse, and disposal of mineral materials; the reduction of health and safety hazards in mining and processing; and minimizing undesirable environmental effects. The production, conservation, sale, and distribution of helium is also conducted under the Research Directorate.

Jan 1, 1981

By Gordon E. Green

This report addresses remote monitoring of coal waste impoundments for stability. Existing automated geotechnical monitoring systems are described and reviewed along with details of instruments suitable for such systems. An impoundment in West Virginia which was in the construction stage was instrumented and monitored between July 1979 and may 1981. Sensors which measure surface and subsurface parameters including settlement, horizontal deflection, surface tilt, pore water pressure, seepage, pond level, and meteorological parameters were installed. Data from the 37 sensors were collected by on-site logger and transmitted by telephone to a central processing station in Seattle for recording and interpretation. Difficulties were encountered with telephone and powerline outages and malfunction of electronic units. Detailed descriptions of the design and performance of the system are provided along with evaluation and comparison with other systems. Recommendations for improving and expanding the capabilities of the monitoring system are given.

Jan 1, 1982

By D. Harrington

The record of fatalities from mine explosions in the United States during the past 3 years has been the best in the history of the mining industry. During these 3 fiscal years, mine explosions have resulted in an average of 4I0 deaths per year, as compared with an average of 153 deaths per year for the preceding; 5 years; an average of 542 deaths per year for the 3-year period 1907-09, inclusive, just before the organization of the U. S. Bureau of Mines; and a yearly average of 265 deaths per year for the 20-year period prior to 1929. This remarkable reduction in deaths from mine explosions demonstrates clearly that mine explosions can be controlled; in fact, they can be prevented when or if the mining people of the United States see fit to take the readily available precautions necessary to bring about this desirable objective. Several large coal-producing States, which in the past have had numerous disastrous explosions, have been free from such disasters for continuous periods of as much as 6 years or even longer. The bituminous mines of Pennsylvania, the largest coal-producing State, give a good example of what can be done to prevent explosions; this State has had only one major explosion (and it resulted in 7 fatalities) during the past 6 years, and no explosion occurred in the several hundred bituminous-coal mines of the State during the past fiscal year. This is a truly remarkable record when compared with past performance in any year in the operation of coal mines in Pennsylvania.

Jan 1, 1936