Search Documents

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.1 Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period 0f approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. Vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the system could be degassed thoroughly in

Jan 1, 1948

By Clarence E. Sims

DURING the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity.

Jan 1, 1947

By M. Mostert

Mining companies sponsor a range of non-core, corporate social responsibility projects to adhere to social and labour plans and environmental management prerequisites that form part of a mining licence application. Some companies go above and beyond such projects, sponsoring initiatives that generate renewable energy through solar power, wind energy, natural gas, etc. The challenge for these companies is to choose between a variety of projects to ensure maximum value, especially in times when the economic climate might be less favourable for such projects. The focus of this research was to analyse the concept of sustainability as it exists today, and to apply that to the triple bottom line accounting method in an attempt to quantify the sustainability of a project. Research was done on the methane burn-off project at Sibanye Gold?s Beatrix Mine to establish how such projects are planned and financed, and what impact they have on the triple bottom line of a company. The financial bottom line is, by definition, one that executives understand. This paper also proposes a quantitative method for defining the social and environmental bottom lines as well. By considering the financial, social, and environmental values, the study attempts to determine a monetary value for a sustainable renewable energy project. This monetary value can be compared to similar values obtained for other sustainable renewable energy projects under consideration. The research suggests that monetary value alone is not enough to base a sustainable decision on, and qualitative measures are suggested for use in conjunction with quantitative methods. The selection method proposed should assist the board of a mining company to choose the most sustainable option and the project that will add the greatest value to the company across all three bottom lines. It will also provide increased justification for such renewable energy projects, even in periods of harsh or uncertain economic climates.

Jan 1, 2014

By J. J. B. Rutherford

IT is now well known that troublesome intercrystalline corrosion may occur in austenitic stainless steels following exposure of the metal to a temperature within the range 1000° to 1500° F. (540° to 815° C.). The present paper describes a satisfactory method of estimating the extent of such corrosion, based on the measurement of the electrical resistance of a specimen before and after attack. This new method enabled us to study quantitatively the effect of several factors upon intergranular corrosion in the 18 Cr, 8 Ni type of alloy. The results show that susceptibility to this attack increases with increasing carbon content and grain size and appears to pass through a maximum for certain combinations of temperature of sensitization and period during which the alloy was maintained at that temperature; and are in complete accord with our interpretation of the mechanism of this phenomenon. The method is probably applicable to other metals or alloys subject to intercrystalline attack, such as the aluminum alloys of the duralumin type. The methods hitherto in use for estimating the degree of intergranular attack fall into three types: (1) microscopic examination,1 (2) macroscopic examination of fractures, and (3) determination of the time required for complete failure or disintegration .2 None of these lends itself very well to a measurement of the extent of corrosion. The first two are qualitative in nature and the third provides an arbitrary value largely dependent on individual judgment, since failure is a progressive phenomenon and not a sudden event. Our experience is that weight-loss determinations, although valuable in some types of corrosion investigations, bear no simple relation to intercrystalline corrosion in this type of alloy, as is to be expected since the phenomenon probably involves only the thinnest films between adjacent metallic grains.

Jan 1, 1932

By R. P. King

A class of gravity separation unit operations in ore-dressing relies for its operation on the production of a stratified bed. Heavier material gravitates downwards, and separation is achieved by splitting the ore horizontally, with the recovery of a dense stream and a lighter stream. The important ore-dressing unit operations that fall in this class are the jig, the Reichert cone and the pinched sluice. A new quantitative model based on Mayer's potential theory is developed here. This model is developed completely for the simple case of binary mono-size particulate materials, but the extension to units operating with feed material distributed over particle size and density is discussed in principle. The model can be used to predict the performance of these units and is very suitable for simulation. The model is tested successfully against experimental data obtained from a batch jig and a Reichert cone.

Jan 1, 1987

By Shuji Owada, Shinya Suzuki, Chiharu Tokoro, Daisuke Haraguchi, Sayaka Izawa

"Coprecipitation with ferrihydrite has been one of the major treatment method for As(V) removal from wastewater such as acid mine drainage. We already confirmed coprecipitation of As(V) with ferrihydrite consists of two kinds of mechanism; one is two dimensional As(V) uptake to the surface of ferrihydrite by surface complexation and another is three dimensional As(V) uptake into ferrihydrite by surface precipitation. We also already confirmed As(V) adsorption process by ferrihydrite could be quantitatively evaluated by original surface complexation model with parameter values reported by Dzombak and Morel. However, As(V) coprecipitation process couldn’t quantitatively be represented by only the original model. In this study, construction and calculation using surface precipitation model were attempted for As(V) coprecipitation treatment with ferrihydrite. In the surface precipitation model, precipitation was described by the formation of solid compound between ferrihydrite and ferric arsenate. Activity of these precipitates was determined by surface precipitation ratio of FeAsO4(s) obtained experimentally from XANES analyses. Solubility products of surface precipitation of FeAsO4(s) (Ksp_FeAsO4(suf.)) were determined by fitting to sorption densities and surface precipitation ratio in each condition. The values of Ksp_FeAsO4(suf.) were determined 10-7.7 at pH5 and 10-10.2 at pH7, respectively. Based on the obtained Ksp_FeAsO4(suf.) value, As(V) removal and isotherm were calculated for As(V) co-precipitation treatment using surface precipitation model. Good agreement between experimental and calculated values was observed. These results were suggested that the quantitative prediction of As(V) co-precipitation treatment was possible if Ksp_FeAsO4(suf.) value was estimated experimentally."

Jan 1, 2014

By M Zoorabadi, Y Zhang, D Bringemeier, S Nicoll, N Kerr

Lihir operations of Newcrest Mining Limited (NML) are on Lihir Island (PNG) which is located approximately 900 km north-north-east of the national capital Port Moresby. The mine is located within the Luise Caldera of the Luise Volcano which is located on the east coast of the island. The caldera is an extinct volcanic crater that is geothermally active. Volcanic activity on Lihir Island is limited to remnant hydrothermal venting in the Luise Caldera in the form of hot springs and fumaroles. Steam and gas (including H2S) naturally discharge within the pit area and along the Kapit beach and near shore region. The hydrothermal reservoir temperatures can reach 100°C at the water table and exceed 200°C at depth. Newcrest maintains a Geo-hazard Management Plan to identify and manage the various geotechnical and geothermal hazards on-site. The major geothermal hazard to mining at Lihir is the occurrence of geothermal outbursts, which have occurred in the past with varying intensities and caused two ‘near misses’, production delays and material losses.

Nov 29, 2022

By X. Gumede

A model is being developed to quantify the benefits for mining houses resulting from the reduction in greenhouse gas and energy consumption by the application of innovative blast designs in addition to direct financial benefits throughout the mine to mill value chain. The conversion from shock tube initiation systems to electronics and some changes to powder factor measured on an open pit mine had previously been used to show significant improvement on blast outputs. Benefits were realised on drilling, blasting, loading, hauling and beneficiation. Quantification of the relationship between powder factor and reduced greenhouse gasses is investigated in this study. The study has highlighted new data that must be recorded and hence some assumptions were made as to fuel consumption and the energy in crushing was obtained from the Bond work equation. The mine to mill projects in an open pit platinum mine and a quarry produced energy savings and reduced greenhouse gas emissions associated with the careful application of explosives and blast innovations. The less fines project showed an increased carbon footprint. The model provides a new insight into how project feasibility should be decided based on economic and environmental viability.

Jan 1, 2012

By Stanley C. Herold

TWENTY-FIVE years ago no distinction was made between water wells and oil wells except in the nature of the fluid produced. Water wells usually showed no decline in their rate of production; when oil wells showed decline something in the manner of handling them was considered wrong. Both water and oil were believed to be subject to the same physical laws in their underground movement toward the wells. Today a sharp distinction is made between them. Whereas water exists alone in the porous formations at depth, oil is usually accompanied by gas. This mixture does not behave as a liquid alone. It is a frothy, seething mass of foam which approaches and enters the wells. Different physical laws come into play. Twenty-five years ago attention was directed entirely to the well itself; today the well is accepted as a mere hole in the ground, a hole to be equipped properly for efficient service, yet without any value whatever unless it is backed up by a sufficiently prolific reservoir. Then, we were concerned with wells alone, 3000 ft. in depth; now commercial wells and their reservoirs are 10.000 ft. deep. Petroleum engineering concepts have necessarily therefore undergone a change in this last quarter century. What are they today?

Jan 1, 1937

By Jiwen Zhang

Abstract Due to the blocking nature at the crusher station, straightforward application of queuing theory cannot give realistic results on the performance of a shovel-truck-crusher system. A new queuing network-based model has been developed in which, the crusher station is formulated into an open queuing network and the whole shovel-truck-crusher system into a closed queuing network with the crusher station as a special server. To fully account for the influence of blocking, Monte Carlo simulation is first used to obtain the performance parameters of the open queuing network for the crusher station. The closed queuing network for the entire system is solved by applying the Extended Summation Method (ESUM), in which the crusher server is described by the simulation results. The model has been applied to the Yuanbaoshan open-pit coal mine to analyze its shovel-truck-crusher system and to improve its efficiency. Results indicate that the blocking at the crusher is an important factor affecting the crusher output and in turn the efficiency of the whole system, and prove that the model can realistically describe the behavior of such systems.

Oct 1, 2009

By Jiwen Zhang

Due to the blocking nature at the crusher station, straightforward application of queuing theory cannot give realistic results on the performance of a shovel-truck-crusher system. A new queuing network-based model has been developed in which, the crusher station is formulated into an open queuing network and the whole shovel-truck-crusher system into a closed queuing network with the crusher station as a special server. To fully account for the influence of blocking, Monte Carlo simulation is first used to obtain the performance parameters of the open queuing network for the crusher station. The closed queuing network for the entire system is solved by applying the Extended Summation Method (ESUM), in which the crusher server is described by the simulation results. The model has been applied to the Yuanbaoshan open-pit coal mine to analyze its shovel-truck-crusher system and to improve its efficiency. Results indicate that the blocking at the crusher is an important factor affecting the crusher output and in turn the efficiency of the whole system, and prove that the model can realistically describe the behavior of such systems.

Oct 1, 2009

By Bhargav Dhavala, Sristy Raj, Ashok Kumar, Suman Krishna Sit, Adity Ganguly, D. P. Chakraborty

"Tatasteel’s West Bokaro washery#3 is designed to deslime raw coal at 0.5mm; the oversize (+0.5mm) is beneficiated in dense media cyclones (DMC) while the undersize (-0.5mm) is beneficiated in froth flotation (FF) cells. Nearly, 80% of the raw coal feed reports to the DMC circuit consisting of four parallel streams. Presently, the performance of DMCs at washery#3 is interpreted by: (a) comparing the actual plant yield w.r.t the lab predicted yield and (b) misplacement of clean coal to middllings.However, the comparison between actual & lab predicted yield is fallacious given the fact that the lab predicts yield of the borehole sample while the feed received at the plant has different characteristics altogether due to the dilution during mining. To mitigate the said limitations, a quick diagnosis tool using the past data has been developed that will give a prediction of performance of different coal seams in the DMCs, inputs being feed ash to DMCs and stream wise feed specific gravity (coal & magnetite combined).The tool also will help in identifying the root cause on real time basis thereby helping the operator to take necessary corrective actions. The operator can intimate the mining personnel in cases of shale reporting to the feed as a result of dilution during mining. In events of higher standard deviations between the parallel streams w.r.t feed specific gravity, the operator can adjust the parameters accordingly to minimize the yield loss. INTRODUCTION West Bokaro came into existence in 1948, as an independent coal company, managed by M/S Anderson Wright. Tata Steel acquired the Company in 1956 to meet its requirement of metallurgical grade coal for Iron making. Subsequently, in 1976, it was made a division of Tata Steel. In 1974, when coal mines were nationalized, West Bokaro was exempted as it produced coal only for captive consumption of the Steel Works. The first washery of India was set up in West Bokaro. The business objective of the West Bokaro division is to produce clean coal at optimum cost for captive use in the steel plant of Tata Steel at Jamshedpur. The strategy is to reduce ash with minimum loss of yield so that quality of coal improves and yet the cost is beneficial vis-a vis imported coal. The primary product is the metallurgical grade coal for coke ovens, which converts coal into coke for use in the Blast Furnaces."

Jan 1, 2018

By T. Fernandez, V. Juchen, C. Petter, F. Cantini, V. Lenz, V. I. Araújo, R. Petter, R. Darrigo, A. Young, I. G. da Costa, J. Oppermann

There are many methods to estimate costs quickly. One of these is the Parametric Method, where costs are estimated from general algorithms (or curves). Derived from an original tool based on the O’Hara model, a software called MAFMINE was developed. MAFMINE is based on parametric models to estimate investment and operational costs in mining. The software itself is based on the use of a computer model known as client-server. However, the model needs new inputs from advances made by the mining industry, mainly in terms of electrification, automation, digital transformation and preconcentration to face Environmental, Social and Governance (ESG) concerns. Thus, this work was to prepare a new core module ready to incorporate the new technologies aiming to deliver operation and capital costs associated with environmental impact mitigation. The tool generates an order of magnitude estimate for CAPEX and OPEX to establish a very first Discounted Cash Flow (DCF) in a mining venture. For quick evaluations, at a preliminary level, the results are very promising.

Mar 2, 2022

By E. J. Wasp

The transportation of mine products incurs a cost which can have a significant bearing on the competitive position of the manufactured product. Clearly, the engineer who is responsible for selecting a mode of transport must base his decision, at least in large measure, on economic comparisons. And today, the engineer usually finds that he has to choose between several modes, including slurry pipelines. For the purpose of an initial economic screening, it is not necessary to go deeply into the technical details of a slurry system. What is usually needed, however, is a method with which the engineer can make a quick economic assessment to determine whether a slurry pipeline should be included in the detailed final analysis. This paper presents a rapid method for making such a preliminary appraisal. Experience with commercial slurry pipeline systems in several countries and with a variety of solid materials has shown that if several assumptions pertaining to critical design variables are made, it is possible to roughly estimate the transportation cost of a slurry system on the basis of only three factors: the specific gravity of the solid material, the length of the system, and the quantity of slurry to be pumped each year. It is assumed that conditions pertaining to field construction, corrosion inhibition, and the like, will be favorable. This assumption is critical because any factor which analysis shows to be particularly unfavorable will raise the total transportation cost estimate which this paper establishes. If the engineer employs this estimating procedure and decides that the use of a slurry pipeline is economically unattractive, his chances of being wrong are small. Conversely, if his quick appraisal indicates that the use of a slurry system is economically favorable, the engineer is justified in committing the time and money needed to make a more detailed investigation of the slurry pipeline potential.

Jan 1, 1969

By G. Gaidajis

In this paper, a semi-qualitative methodology is presented and then applied to an aluminium extrusion industrial facility in order to perform an initial environmental assessment. The results of the assessment enable an improved understanding of the environmental performance of the facility and more importantly identify the areas of significant environmental concern. Following, the application of case-specific sustainability indicators related with the areas of significant environmental concern, leads to a more comprehensive sustainability assessment. The applied two-step approach offers a quick and reliable environmental assessment and help focusing on the most environmentally problematic areas. Moreover, the follow-up of the specific indicators seems to be appropriate for the improvement of the environmental performance of the examined industrial facility.

Jan 1, 2008

By D. Menne

A comminution model and a quick laboratory milling test procedure are presented. These allow the determination of milling parameters for the - optimization of ball size and pulp density in operating mills estimation of the performance of new feed stocks in an existing mill - estimation of the expected milling performance for a new project. Information on the estimation of the size of mills to deliver specified amounts of comminution energy, and amount of expected ball, rod, and liner wear to allow cost estimates for new projects, is also included.

Jan 1, 1983

By Walter J. Johnson, Robert L. Chufo

A unique non-contracting coal thickness measurement technique has been developed to measure both the dielectric constant and thickness of a coal seam as part of a sensor array supporting an autonomous coal mining machine. The sensor measures the reflection of an electromagnetic signal from the coal/shale interface. Underground measurements of coal 6- in thick with a dielectric constant of 4 have been confirmed. Measurements were also made of a 31-in thick coal pillar for application of the sensor to highwall mining. The electromagnetic measurement technique, the data reduction process and field test experience will be presented.

Jan 1, 1992

By G. L. Mowrey

In addition to developing various types of coal interface detection systems, the U.S. Bureau of Mines is actively involved in developing a coal rib thickness monitoring system for high wall mining applications. One particular system that appears to show promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1995

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection system, the US Bureau of Miner is actively in involved in developing a coal rib-thickness monitoring system for highwall mining applications. One particular system that shows promise in a ground-pentetrating radar system to detect the coal-air boundaries of coal rifts. Based on preliminary laboratory and field tests results indicate that this method can be applied successfully in highwall mines to maintain constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection systems, the US Bureau of Mines is actively involved in developing a coal rib-thickness monitoring system for high wall mining applications. One particular system that shows promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1996