Search Documents

By Shadia J. Ikhmayies

Nanocrystalline CdS:In thin films with particle size in the range (3-36 nm) were produced by the spray pyrolysis technique on glass substrates. The films were characterized by investigating their X-ray diffractograms (XRD), scanning electron microscope images (SEM), transmittance curves and photoluminescence (PL) spectra. The size of the nanocrystallites was estimated from XRD difractograms and then from the hyperbolic band model and the bandgap energies of the nano- particles, which were calculated from the positions of the minima in the first derivative curve of the absorbance. Fine-structured PL spectra confirmed the nanocrystalline nature of the films.

Jan 1, 2010

By Preston C. Holloway

Transformational roasting involves the heating of a material along with specific additives to induce mineralogical changes in the starting material. By controlling the chemical composition, roasting atmosphere, temperature and time of reaction, the mineral transformations induced during roasting can be engineered to control the distribution of valuable, or harmful, metals and to produce new mineral assemblages that are more amenable to conventional methods of metals recovery or to environmentally safe disposal. To date, this type of process has only been applied to the recovery of a limited number of metals, but current research is looking to expand the application of these techniques to the recovery of metals from a wider range of materials. An introduction to these techniques is presented along with preliminary results from their application to metals recovery from zinc bearing wastes, such as zinc ferrite leach residues and carbon steel electric arc furnace dust.

Jan 1, 2006

By Leith Sharp

I was confronted with a profound dilemma as an undergraduate engineering student at the University of New South Wales in Australia in 1992. I had been taught that our planetary life-support systems were in a state of alarming decline by an institution that operated as if what the faculty was teaching was irrelevant. Lights were left on in empty overcooled classrooms, recycling bins were nonexistent, lawns were maintained using pesticides and herbicides, diesel trucks spewed fumes as they passed on their way to drop off chlorine-bleached virgin paper. This disconnect was very alarming to me. While it was obvious that universities should play a leading role in teaching and researching sustainability issues, I wondered how it could be possible to make widespread institutional changes to meet the demands of environmental sustainability when it was not even being done in the very university sector where these ideas were being promulgated. If universities would not change, then who can and who will, I wondered? To a growing number of people, the idea of teaching sustainability without demonstrating it is highly problematic. It is also widely believed that the ability of the higher education sector to reform its own practices is an important indicator of humankind?s ability to address the global environmental imperative across all sectors of society. These sentiments have helped fuel what is now referred to as the campus sustainability movement, a movement dedicated to transforming our campuses into living laboratories for the demonstration and practice of environmental sustainability.

Jan 1, 2010

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By Anja Pfennig, Axel Kranzmann, Sabrina Schulze

The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.7225 42CrMo4, used for casing, and the stainless injectionpipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=lOO bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite F eC03 in both types of steel.

Jan 1, 2013

By Zeljka Pokrajcic

Crushing and grinding, or comminution, circuits are the most energy intensive process of a mineral processing plant. Comminution involves the physical size reduction of an orebody to a particle size sufficient for recovery of the mineral values. However, the comminution process remains inherently inefficient. The inefficiency is a result of the operating nature of comminution devices such as grinding mills, where transfer of energy between grinding media and particles in unconstrained and completely random. New comminution circuit design strategies are presented in this paper. The aim of the new strategies is to improve the overall efficiency of the comminution process and reduce the total energy consumption of a comminution circuit. The energy efficient strategies include the: ? rejection of coarse size liberated gangue from the comminution circuit and further downstream size reduction ? use of more efficient grinding and crushing equipment ? the selection of coarser particle product sizes to alleviate the increased energy intensity required to achieve finer product sizes Singularly and when combined, these energy efficient strategies can significantly decrease the overall energy consumption of a comminution circuit. This paper also explores the financial impact of certain energy efficient strategies using an analysis tool called EcoNomics?. It shows that substantial financial gains can be made by including more efficient technologies and methods in comminution circuit design.

Jan 1, 2010

By Keith S. McIntosh

The fire assay process for the quantitative recovery of platinum group elements (PGE?s) prior to subsequent analysis traditionally is a time-consuming process. Samples derive from various ore types and contain PGE?s at the ppm or ppb levels, making concentration of the elements mandatory before assaying. Traditionally sample turn-around times are of the order of 24 hours. The whole sequence of sample preparation, fire assay and subsequent analysis of PGE?s have been automated by Anglo Platinum. Some of the major challenges on the road to automation will be discussed and the novel solutions that were implemented. The engineered solution included robotic automation of the whole sequence, from sample preparation, up to the final element by element assay. The final system allowed for rapid (less than one hour) and accurate analysis of PGE?s even in streams containing very low levels, such as flotation tailing streams and drill core samples.

Jan 1, 2006

By Shadia J. Ikhmayies

The SnO2/CdS/CdTe thin film solar cells were fabricated on glass substrates by using the spray pyrolysis (SP) technique for the deposition of the SnO2 and CdS layers and vacuum evaporation for the CdTe layer. The transmittance curves were used to investigate the interdiffusion in the two interfacial regions SnO2/CdS and CdS/CdTe by taking the first derivative of the absorbance as a function of wavelength. The appearance of new bandgaps around the bandgaps of SnO2:F, CdS:In and CdTe layers is a strong evidence on the interdiffusion in the two interfacial regions and/or the formation of quantum dots.

Jan 1, 2010

By Mark C. L. Patterson

Hydrothermal brines are extracted from significant depths below the surface of the earth and arrive at the surface at elevated pressure and temperature. The exact chemistry and conditions of these brines depends upon the rock formations through which the water travels, but many of the brines are rich in dissolved minerals especially silica which is often saturated in the brine. At pressure and temperature the minerals remain in solution but in order to extract heat from the brines, they need to be cooled and during which many of the minerals precipitate causing problems. Where precipitation is a problem in the downstream processing, the brines are maintained at a high enough temperature and pressure so as to avoid precipitation and injected back into the geothermal formation. This results in a significant loss in potential energy that could be recovered from the geothermal brines. If left to precipitate in an uncontrolled manner, many of the minerals will precipitate as gels, in a high surface area form which is difficult to extract from the liquor and which can causes problems. Precipitation in this manner often builds up on the inside of pipes, reducing the pipe cross-section available for fluid flow and reducing the overall efficiency of the plant. If the brines are seeded at the appropriate time or the precipitation conditions are changed, mineral particles can be grown and separated more easily from the brine. During this precipitation and growth phase the chemistry of the local environment can also be altered to grow more valuable particulates. Some of the specific chemistries will be discussed with reference to known geothermal brines and what needs to be done to precipitate value added products. A theoretical approach to the complete extraction of minerals from geothermal brines is also discussed with the goal of extracting more heat from the brine prior to reinjection into the well.

Jan 1, 2006

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By Jian Zhang

From the standpoint of quality, surface cracks normally pose more of a problem than internal cracks. Hypo-peritectic (HP) steel grades are well known for their proneness to surface longitudinal cracking (SLC) during continuous casting. This study analyzed the influences of chemical composition, technique parameter and secondary cooling on the surface longitudinal cracks. Based on the optimized the first and secondary cooling zone water distribution in the process of continuous casting, low cooling water distribution at solidification initial stages and uniform cooling at secondary cooling zone were suggested, which can be used to effectively control the surface longitudinal cracks.

Jan 1, 2010

Equilibrium calculational software programs can be effectively utilized to illustrate the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation to students studying hydrometallurgy. The calculational program STABCAL will be demonstrated. illustrative examples for the creation of diagrams such as EH-pH, activity or concentration-pH and activity or concentration-EH will be presented to demonstrate the fundamentals of real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Applications will include treatment of Acid Mine Drainage (Berkeley Pitlake water and sediments), mass balance potential/pH diagrams, leaching and selective separation of metals from electroplating sludge, metal adsorption at femhydrite surfaces, and flowsheet development for treating mercury sulfide K106 sludge.

Jan 1, 2002

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By Seong- Rin Lim

Light-emitting diodes (LEDs) are regarded as environmentally friendly light sources due to their high energy efficiency and lack of mercury content. LEDs are used for a variety of domestic and commercial lighting systems, where they are replacing incandescent and fluorescent lamps at a rapid rate. Incandescent lamps inefficiently consume energy because electricity is mostly converted to heat rather than light. This causes unnecessary environmental impacts and energy consumption associated with power generation and transmission from a life cycle perspective. Although fluorescent lamps are more energy-efficient than incandescent lamps, their disposal at end-of-life presents special challenges because of the presence of toxic mercury. Despite the seemingly apparent advantages of LED, very few studies have rigorously addressed potential environmental consequences of their disposal. Specifically, LEDs are designed with III-V semiconductors that presumably consist of toxic and rare materials, including arsenic, gallium, and indium. We hypothesize that, depending on their concentrations and leachability, these constituents may also contribute to render LEDs as hazardous waste at the end of their useful life.

Jan 1, 2010

By Viviane Tavares

The technology advance of mobile devices makes consumers of these equipment do more constant exchanges, with this the obsolete devices discarding becomes an environmental problem, due its landfill accumulation. In order to minimize the environmental impacts caused by these equipment there?s the recycling necessity of polymers, ceramic and metallic materials. The main goal of this recycling is to study the printed circuit board of device mobile processing through ore treatment in order to recoup copper. Initially printed circuit boards were processed in a knives mill, in order to liberate the ferrous material, after that it was done the magnetic separation of the reduced residue. With the not magnetic fraction it was done the grain sized analysis and sulfuric acid and hydrogen peroxide leaching analysis. With the chemical analysis results proceeding from the leaching aliquot it was possible to observe that the leaching method with sulfuric acid and hydrogen peroxide presented greater copper recovery.

Jan 1, 2009

By Carl W. Lam

The increased obsolescence rate of electronic products has made it evermore pertinent to understand the potential environmental impact of materials choices to help guide electronic waste (e-waste) management and promote awareness of high burden materials. Methods for screening for the performance of materials and their potential burden on human health and the environment can be used to comparatively select constituents of present and prospective electronic products. These methods should be able to yield more robust information when linked to other decision-making strategies where integrated data on consumer preferences, production quantities, and regulatory initiatives are sparse or unavailable. A framework is presented here for generating metrics of ecological toxicity, human health toxicity (cancer and non-cancer categories) and global resource consumption for evaluating environmental impact of materials (specifically metals) in electronic products. The time-dependent impact trends of United States? printed wiring board (PWB) metals usage, principally derive

Jan 1, 2010

By Junli Xu, Xianwei Hu, Kaiyu Xie, Liangxing Li, Zhongning Shi, Zhaowen Wang, Bingliang Gao, Aimin Liu

Al-Ti master alloys were prepared by aluminothermic reduction between the dissolved titanium dioxide and aluminum in cryolite melts at 960oC. The kinetic analysis by differential scanning calorimetry indicated that the apparent activation energy of the reaction of reducing titanium dioxide by aluminium is 22.3 kJ/mol, and the reaction order is 0.5. The products were analyzed by means of X-ray diffraction, X-ray fluorescence, scanning electron microscopy and energy dispersive spectrometer. Results from X-ray diffraction showed that the phase compositions of produced alloys are Al and Al3Ti. In addition, Al-Ti master alloys containing 2-6 mass% Ti were formed at different reduction time of 2-5h in aluminothermic reduction experiment.

Jan 1, 2015

By M. Hochenhofer

Keywords: desulfurization, mathematical model, slag reaction To produce ferroalloys like ferro-nickel for alloying purposes in a quality that meets the requirements of today?s steel industry, refining processes like desulfurization and dephosphorization are indispensable. The performance of desulfurization-treatment by slag reaction depends on various parameters, such as: sulfide capacity and viscosity of the slag, sulfur distribution between metal and slag, activity of sulfur in melt and movement of melt. Within this work, the combined influences of these parameters on the desulfurization of a ferro-nickel alloy were examined. As a basis for this examination, a mathematical model, based on data from plant trials, was created. This model demonstrates the relationship between desulfurization rate and initial values of the above mentioned parameters. With this model the relevant parameters were evaluated and assessed concerning their influence on desulfurization.

Jan 1, 2005

By P. N. Anyalebechi

The effects of a cross-hatched grooved mold surface topography, casting speed, and superheat on the morphology of solidifying shells of aluminum alloy 3003 have been characterized by a series of immersion tests. The cross-hatched grooves were 0.232 mm deep with wavelength or spacing between 1 mm and 15 mm. The shells solidified at casting speed of less than 10 mm/s on the 1 mm spaced cross-hatched grooved mold surface were fairly uniform with little or no localized variations in thickness. However, the propensity for non-uniform shell growth morphology was exacerbated by an increase in casting speed, melt superheat, and the wavelength of the cross-hatched grooves. This is provisionally attributed to their effects on interfacial heat transfer and wetting of the mold surface by the molten metal.

Jan 1, 2008

By Jilai Xue

Oxygen gas bubbles generate on anode during Pb electro-deposition process in PbSiF6-H2SiF6 aqueous solutions at room temperature. Cell voltage varies as the bubbles formed on the anodes surface. The bubble layer on the anode makes a voltage drop that consumes energy in the Pb process, which can be reduced by applying ultrasound on the anode. The effects of ultrasound frequency and anodic current density were investigated with ultrasound on and off, alternatively during the Pb electrode-position process. The removing of the gas bubbles were recorded in association with a drop in the cell voltage. The cell voltage can be lowered by 4% - 6% with ultrasound, which has potential for energy saving in Pb production.

Jan 1, 2010