Search Documents

By Philippe Henry

"Hydrometal provides an adequate technology to reintroduce otherwise lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Two case studies at an integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed: (I) Residual low quality acid and caustic are used in the processing of zinc industry cements to produce copper, nickel, cobalt and zinc concentrates by several consecutive selective leach - precipitation processes.(II) Copper anode slimes are treated and their precious metal contents are recovered. Depending on the composition of the slimes, separate or combined concentrates of copper, bismuth, tellurium/selenium and silver/precious metals can be produced."

Jan 1, 2008

By Stein Tore Johansen

Some ferro-silicon furnaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the?off?gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels close to the furnace is observed. The result is irregular stops to clean the off-gas channels. The paper focuses on the nature of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderúrgica Belgo Mineira, João Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By Leonard J. Friedman

The recovery of sulfur dioxide from metallurgical gases for the production of sulfuric acid has been an effective means of reducing sulfur dioxide emissions from non-ferrous smelters. Sulfuric acid has been produced from gas originating from fluid bed roasters, electric furnaces, reverberatory furnaces, flash smelting furnaces, Pierce Smith and flash converters, sinter machines, etc. The gas from each of these sources has a unique set of variables that affect the design and operation of the sulfuric acid plant. In addition, the sulfuric acid plant itself has been evolving, with new equipment designs and materials. This paper will review each of the unit operations in the gas cleaning and contact sections of the metallurgical sulfuric acid plant, discussing various equipment designs, materials and the handling of gas stream variables and impurities. The paper updates to 2006 previous works on metallurgical sulfuric acid plants by the authors.

Jan 1, 2006

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By Raj P. Singh

Two design-of-experiments studies were carried out to investigate the leaching of technical grade molybdenum tri-oxide (TGM) in the presence of hydrochloric acid and the mother liquor of ammonium di-molybdate crystallization used as an ammonia source. Results indicated that leaching of TGM in HCl is possible only when used at about 1N concentration. In high concentrations of HCl, technical grade MoO3 had very high solubility (7.5 to 40 g/L Mo). The most suitable conditions for HCl leaching of TGM were obtained at a slightly elevated temperature of 80°C. Using about 1N HCl at 80°C, potassium in the leached solids (TGM) decreased to about 110 ppm, a value typically obtained in TGM leached in HNO3 - NH4NO3media (3.5 - 4.0 moles /L HNO3 + 0.5 ? 1.0 moles/L NH4NO3). Mo losses under these conditions were 0.8-0.9 g/L Mo. The HCl-leach method, presented here-in, has a significant advantage in chemical cost and environmental benefits over HNO3 ? NH4NO3 purification method.

Jan 1, 2006

By Sergio N. Monteiro

Lignocellulosic fibers obtained from plants like cotton, flax, hemp, sisal, jute and many others are natural materials used, since long time, in basic items such as textile, baskets, roofing and carpets. These traditional natural fibers as well as some new ones are nowadays replacing synthetic fibers as composite reinforcement owing to environmental advantages. The heterogeneous characteristic of lignocellulosic fibers is, however, a limitation for application in composites. The buriti fiber, extracted from a tropical plant tree, is recently being investigated as a possible reinforcement for polymeric matrix composites but no complete information exists regarding its mechanical behavior. The objective of this work was then to carry out a statistical analysis on the mechanical properties? uniformity of buriti fibers. By precise dimensional measurements in association with tensile tests, it was found that the mechanical properties depend on the range of the fibers? dimension.

Jan 1, 2009

By Aline Maria dos Santos Teixeira, Francisco Manoel dos Santos Garrido, Joao Alves Sampaio, Marta Eloisa Medeiros

"Rocks for crops is a natural practice for soils fertilization which consists on adding rocks to the soil while water decomposes the rock, through chemical weathering, and gradually releases nutrients to the soil solution. This practice can be considered an alternative to the low production of potassium fertilizers in Brazil. In this context, the phonolite rock was characterized in order to evaluate its application as an alternative source of nutrients to the Brazilian agriculture. The phonolite studied is an igneous, volcanic rock with alkaline character that is chemically composed of a high grade of potassium due to the presence of feldspar minerals. In order to quantify the minerals present in the sample, characterization was carried out using several techniques such as X-ray diffraction, X-ray fluorescence and scanning electron microscopy.IntroductionBrazilian soils are generally acidic and nutrient poor due to the tropical climate in which high temperatures and intense rainfall favor a rapid decomposition of the rocks that from the soil. And as agriculture is one of the main bases of the country's economy, large amounts of fertilizer are used to make the soil productive.Although Brazil has large reserves of potassium, the demand for potash fertilizer is higher than the national supply, which makes the country dependent on fertilizer imports, especially in the form of potassium chloride. Thus, we must look for economic alternatives to traditional fertilizer [1].Stonemeal is a natural practice for soil fertilization that consists in adding basic or ultrabasic rocks to the soil so that water, through chemical weathering, decomposes the rock while it gradually releases nutrients."

Jan 1, 2011

By Xuewei Lv

An intelligent recognition and quantification system for the micrographs iron ore sinter was developed in the current paper. The average distribution parameters in a gray histogram of minerals by a Gaussian gray distribution model were obtained. The feature curves of the gray histogram of two minerals were achieved by combining the two density functions. The feature indexes, such as the number and position of the peaks and the valleys of two minerals in different ratios, were quantified by differentiating the distribution functions. This algorithm is able to extract the feature of the minerals adequately and accurately for recognizing the composition and phases of the minerals intelligently.

Jan 1, 2009

By Santhanam Ramesh

"The shell (exoskeleton) waste of shellfish such as shrimps and crabs is the raw material in the extraction of chitosan, a polymer. Chitosan has several medicinal values such as reduction in cholesterol, urea and creatine in the blood. It is estimated that about 40000 tonnes of chitosan may be obtained from all chitin yielding invertebrate sources of India and a foreign exchange of 600 million US$ could be earned annually. Awareness has to be created among sea food processors to put up plants to convert shellfish wastes into chitosan. Similarly pharmaceutical industries may use chitosan in the development of new drugs. Types of training and awareness programmes to be organized for entrepreneurs, sea food processors and pharamacists are discussed in this paper.IntroductionIndia earns annually foreign exchange to the tune of 0.8 million US$ by exporting processed marine crustacean shellfish resources such as shrimps, crabs and lobsters (Figure 1) through 300 sea food processing industries. At present, only a small quantity of shell wastes (exoskeleton) generated from the above is utilized as an ingredient in fish feeds and hence much of the wastes are disposed off either as land fill or by direct dumping in sea. These wastes containing primarily chitin could be the major raw material for the production of a proteinaceous byproduct viz. chitosan, a highly valued pharmaceutically important source"

Jan 1, 2008

By Edward Peters

Scandium (Sc) has unique properties and is one of the more valuable elements in the periodic table. Scandium can be used in solid oxide fuel cells and to produce high strength aluminium alloys of value, for example, in the aerospace industry. Scandium is often grouped together with the rare earth elements (REE). Amongst others, scandium can be found in bauxite residues, so called red mud. It is possible to extract and enrich scandium from red mud by leaching and solvent extraction. Scandium can then be recovered from the pregnant strip liquor by crystallization. The strip liquor will however still contain certain impurity elements. In the present work, a method for obtaining a pure scandium solid phase by direct crystallization from the strip liquor is evaluated. It was found that Fe and Ti co-precipitate with Sc under the conditions employed.

By Leonardo Mota, Lucas L. da Costa, Milton B. Filho, Sergio N. Monteiro, Helion Vargas, Tammy G. R. Portela da Silva

"A natural biofoam extracted from the buriti palm tree has shown characteristics for potential substitution of synthetic foams. In the present work, a photoacoustic thermal characterization was performed on buriti biofoam samples. An open photoacoustic cell technique and a photothermal rise method performed under continuous laser illumination were employed in order to determine the thermal diffusivity and the specific heat capacity of such material. In addition to their intrinsic values (finger print), these physical parameters represent the light-into-heat conversion efficiency and the amount of heat stored per unit volume, respectively. The results showed that the buriti biofoam presents thermal properties that permit its use as an effective insulation material.IntroductionSolid foams are very light materials with increasing engineering applications [1]. A natural biofoam obtained from the petiole of the buriti palm tree (Mauritia flexuosa) has been recently investigated [2-4]. The evaluation of the buriti biofoam properties and the characterization of its microstructural aspects have shown that this biofoam has a potential as a new engineering material with very low density. Additionally, its reduced open porosity and low absorbed humidity revealed a promising material for packing and floating applications. In fact, this buriti biofoam, extracted from the palm tree natural of the north region of Brazil, is being used by the low income population as a modest substitute for Styrofoam® [1].As a potential insulating material, the buriti foam needs to be characterized in terms of its thermal and acoustic properties. A preliminary investigation [3] on the thermal behavior of this natural biofoam by thermogravimetric analysis, TGA, and its derivative, DTG, as well as differential scanning calorimetry, DSC, revealed parametric conditions associated with water loss and structural decomposition. Both the surface humidity and the release of hydration water were determined. Different decomposition events were attributed to both, more rigid as well as to more flexible molecular segments. Table 1 depicts technical data obtained so far for the buriti biofoam. These data are compared to those corresponding to Styrofoam®."

Jan 1, 2011

By Robert W. Bartlett

Chalcopyrite in copper flotation concentrates can be hydrothermally converted to digenite with oxygen in a continuous process, with rapid kinetics when operated above 200°C. This eliminates large amounts of sulfur and iron. These "super-concentrates" have potential for debottlenecking smelters and avoiding capital intensive future smelter expansions, otherwise required in the late 1990s. The technology of producing super- concentrates is described, with cost estimates, and the use of super-concentrates as smelter feed is discussed, with examples.

Jan 1, 1992

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft's Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By Bin Du

In recent years, concurrent product design and process is gaining popularity and will become a norm of the industry of the future. Forging has been a critical manufacturing process for production of components with superior tensile strength, toughness and grain flow. This paper describes an expen system which is being developed for forging die design and forging process analysis in concurrent engineering environment. Rules and guidelines pertaining to forgeability are formulated and incorporated into the knowledge-base in building the system. The system is built using an object-oriented paradigm. The object-oriented approach and hierarchical rule structure paradigm are briefly discussed. Finite element analysis packages (ALPID-2D) were incorporated into the program to give the simulation result of the forging process. The system can automatically produce a competent design and recommend a set of processing parameters for a given product. The designer can modify the design according to the result of the simulation.

Jan 1, 1992

By A. J. Meir, Paul G. Schmidt

"We present a novel approach to the mathematical analysis and computational simulation of fully three-dimensional, nonlinear, viscous, incompressible MHD flow in complex configurations involving several liquid and solid conductors. Such configurations arise in numerous metallurgical processes. Employing the current density rather than the magnetic field as the primary electromagnetic variable, it is possible to avoid artificial or highly idealized boundary conditions for electric and magnetic fields and to account exactly for the electromagnetic interaction of the flow region with the surrounding space. In addition, the approach lends itself naturally to finite-element based discretization techniques. As an application, we simulate the stationary flow of an electrically conducting fluid around a solid spherical particle of arbitrary conductivity, in the presence of crossed uniform electric and magnetic fields, and compute the Lorentz, pressure, and viscous forces exerted on the particle. This problem arises in connection with the electromagnetic filtration (purification) of molten metals before the casting stage.IntroductionNumerous metallurgical processes are governed by MHD effects resulting from the macroscopic interaction of liquid metals with applied or induced currents, electric and magnetic fields. Frequently these effects are technologically exploited in order to drive or to control the flow of metallic melts. Typical examples include the electromagnetic stirring of molten metals before the casting stage [1]; electromagnetic turbulence control in induction furnaces [2]; electromagnetic damping of buoyancy-driven flow during solidification [3]; and the electromagnetic shaping of ingots in continuous casting [4]."

Jan 1, 1999

By Chuang Y-Y

A summary is made on the thermodynamic analysis for two of the four ternary systems of the quaternary Cu-Fe-Ni-S. The analysis is being extended to ternary Cu-Fe-S and then to the quaternary. An analysis is already made for the metal ternary but is not reported here. Experiment is being carried out to measure the liquidus surface. of Fe-Ni-S equilbrium with the fcc solid solutions of (Fe, Ni). The presentation at the Symposium will include all the results obtained at the time of presentation.

Jan 1, 1983

By Yang Guangqing, Shao Jiugang, Zhang Jianliang, Wan Dan, Fu Yuandi, Guo Hongwei

"Resource of metallurgical coke is becoming scarce, and although coke can be partially replaced by pulverized coal injection, there are many restrictions for further increase in coal ratio. Mixed charge of ore and lump coal from top to replace more coke was studied in this paper. Softening-melting property of the burden was affected by charge of lump coal. Softening-melting properties of mixed charge of ore and coke, mixed charge of ore and lump coal were tested respectively. Results show: the property of the burden mixed with coke is superior to the burden mixed with lump coal; lump coal would not deteriorate softening-melting property of the burden and some of them can even improve softening-melting property of the burden. Top charge of lump coal would not deteriorate softening-melting process, and this should be a new way to increase coal consumption to decrease coke rate.IntroductionThe blast furnace is still the predominant process for the reduction of iron ore and will probably remain so for the next decades. Metallurgical coke is becoming scarce and expensive, so the cost of hot metal can be decreased by reducing the consumption of metallurgical coke[l]. Coke can be partially replaced by pulverized coal injection, currently the highest rate of pulverized coal reached 266kg/tHM, most of blast furnace PCR is about 150kg/tHM, and it is very difficult to further increase of PCR. Nut coke is charged into blast furnace mixed with iron ore, not only for improving utilization of metallurgical coke, but also for lowering the coke rate. Presently the majority of blast furnaces in the world use nut coke although its amount is very different: from 10-20 to 70--100 kg/tHM and more[2-4].The effect ofnut coke in blast furnace is extensively researched, and the main conclusions recommend: to improve gas permeability of cohesive layer in blast furnace, to promote reduction of iron burden, protect metallurgical coke from the solution in the shaft due to higher reactivity of nut coke. There is no special requirement for the strength of nut coke[5-8]. Nut coke is also used for sintering fuel, which may lead to the shortage of the nut coke charging into blast furnace. So lump coal mixed with iron ore is considered to be charged into the blast furnace, not only to reduce the cost of grinding coal, but also to increase the use amount of coal."

Jan 1, 2013