Search Documents

By Okechukwu Anopuo, Gerhard Tober, Petra Maier

"In this study, an investigation on the microstructure of hot rolled steel S355J2+N was conducted to optimize process parameters of complex forming, which combines rolling and bending. The best sets of parameters are worked out based on homogeneous mechanical properties and microstructure within the varied deformation degree with maximum at <p = 1.14 on a 25 mm thick plates. Mechanical properties, especially of heavy plates, are strongly influenced by the local deformation degree, strain rate and temperature. Detailed microstructural analyses showed that the ferrite-pearlite band structure changes near the surface, while maintaining homogeneous microstructure within the deformed work piece. Surface decarburization was also observed and this leads to decrease in hardness. To minimize iron oxide formation which could lead to side cracking, reduction in exposure time to temperature was suggested. On the other hand, temperature reduction below a critical value would risk the accurate forming process.IntroductionThis work presents the preliminary results of research to develop a new complex deformation process of thick steel plates. Complexity is given because the forming process combines rolling to reduce thickness and profiling by bending. The work piece will experience a thickness reduction from 25mm to 8 mm and is double curved. To explain and understand forming of thick plates basics of sheet forming as well as massive forming need to be used. At the moment there is no forming process established to produce double curved plates including reducing thickness in one process step. Technologies nowadays consist of two process steps: flat rolling and pressing in shape. Due to good weldability and formability the final product will be made of steel S355J2+N. This low-carbon steel is well understood and has a low strengthening exponent, which is expected to keep the forming forces down. Reduction of thickness from 25 mm to 8 mm gives furthermore a high deformation degree. Thus, hot forming has to be applied. The determination of process parameters is the main aim of overall research project; temperatures above lOOO°C are expected. Flow curves in literature are given at various temperatures and strain rates [1]. However, experiments with data close to the industrial application are rarely found, especially at low strain rates and high deformation degrees. Pre-test were done by flat rolling, being aware that the influence of bending is eliminated. The microstructure evolution were characterised in relationship to material formability with special attention to grain size change and recrystallization. Representative samples should be selected from specific locations in the deformation zone according to the knowledge about the metal forming process [2]. Due to no further alloying elements in S355, no precipitation hardening is expected to take place during hot forming, which keeps the mechanisms simple and the concentration on the feasibility of the complex forming process is given."

Jan 1, 2012

By José D. T. Capocchi

Viscosity of liquid lead, tin, and Pb-Sn alloys has been measured by the rotational viscometer method in the temperature range from 50 K above their respective liquidus temperature to 823 K. The results are accurate to within ±1.0 %. The variation of viscosity with temperature followed the Arrhenius-type equation µ = µo.exp(Q/RT). The composition dependence of the isothermal viscosity and the activation energy for viscous flow have not shown anomalous changes at the eutectic composition of the Pb-Sn system.

Jan 1, 2000

By M. Pineau, G. A. Monteith, M. Laliberte, G. Houlachi

Conventional physico-chemical treatment methods, either hydroxide or sulfide precipitation, can hardly achieve a high removal of selenium from the liquid effluents which can be generated in some metallurgical operations. In weak acid solutions, selenium exists mainly as anionic species (selenite Se03-2 and selenate SeCV2) which, therefore, cannot precipitate as metal hydroxide or metal sulfide compounds. At the same time, neither selenite nor selenate form stable precipitates with the common cations (Ca, Mg, Fe, etc.) that are typically used in water treatment. At Noranda Inc., CEZinc Division in Valleyfield, Canada, the introduction of new discharge requirements for effluent toxicity initiated a R&D program which resulted in the full-scale implementation of a new treatment method for selenium removal. The goal of this paper is to present this new method which is now being patented by CEZinc. The process chemistry will be presented along with pilot-scale developments and full-scale operational results.

Jan 1, 2000

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By George E. Cook, Peter C. Levick, Francis M. Wells

"Relationships are established between the peak current of a pulsed, rectangular current waveform and the pulse current duty cycle under conditions of constant arc power. By appropriate choice of these interrelated parameters, it is shown that the arc pressure may be varied over a wide range even though the arc power is held constant. The methodology is suggested as a means of countering the effect of gravity in 5-G welding, while maintaining constant heat input to the weld. Combined with appropriate penetration sensors, the methodology is additionally suggested as a means of controlling penetration. IntroductionBoth low frequency pulsation (typically 0.1 - 20 Hz) and high frequency pulsation (> 100 Hz) are often used with GTA welding. Benefits derived from pulsing include improved weld quality and better process control.Advantages cited for low frequency pulsation include claims that the total heat input to the weld is reduced, the weld bead size is reduced, weld penetration is increased, grain size is reduced, porosity is reduced, weld distortion is reduced, thinner materials can be welded successfully, and the tolerance of the welding process to material and production variations is improved (1-16). With respect to the latter, pulsing aids control of weld bead penetration by increasing the tolerance to component dimensions and joint fit-up. It also reduces the sensitivity to disparities in heat sink, and it helps to reduce distortion in thin section material or distortion attributable to poor clamping. In certain materials it can reduce the sensitivity to surface oxides and to cast to cast compositional variations (16). Low frequency pulsation is also useful in welding thick materials mated by a prepared groove. In these applications the low frequency pulsation is used to obtain proper sidewall fusion as the tungsten electrode is weaved from one side of the groove to the other. In this case the weld current pulsation is synchronized with the cross seam weave pattern, such that the high current pulses occur at each sidewall. This type of low frequency pulsation has proven particularly useful in welding with narrow width groove designs (17-21). Finally, Ecer (22) has shown that the pulsed current arc is more stable against magnetic disturbances than an equivalent constant current arc."

Jan 1, 1986

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The basics of microwave drying process of CuCl residue were studied by comparing the dielectric property of the residue with different moisture contents. The dielectric properties were measured by microwave cavity perturbation method. The dielectric constant and dielectric loss factor of the CuCl residue have a linear correlation with the moisture content. With this relationship, we can realize on-line measurement of moisture content of the CuCl residue by dielectric properties. The microwave drying experiments with different thicknesses (1-5cm) of CuCl residue were carried out, and the heating curve of the materials under different microwave powers (250-450W) was made. From these parameters, an optimized operation parameter of microwave roasting technology, the thickness of CuCl residue filter cake to be microwave roasted should be 2cm , was deduced.

Jan 1, 2015

By J. W. Lyman

The U.S. Department of the Interior, Bureau of Mines, investigated methods to recover valuable rare-earth materials from NdFeB magnet scrap. Although several processing techniques were evaluated" the best separation of rare earths from the NdFeB magnet ,scrap was obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. Both sodium and ammonium intermediate double-salt precipitates&apos; that can be converted to a variety of useful neodymium products were investigated. The sodium system showed a neodymium recovery of 98 pct, while the ammonium system yielded 70 pct during double-salt precipitation. The iron-rich effluent following the rare-earth recovery was treated to produce sodium and ammonium iron jarosites that can be disposed of or converted to hematite. By following this new procedure, many materials handling and economic disadvantages found with fluoride or oxalate direct precipitation were avoided.

Jan 1, 1992

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By James P. Bennett, Jasper Kwong

As concerns about the environment and the disposal of industrial wastes increase, the utilization of spent refractories from electric arc furnaces (EAF) is receiving more attention. Longer service life of refractories in an EAF can be achieved by foaming MgO saturated slag. The refractory wastes removed from a melt shop can be utilized as a part of these slags. The Albany Research Center is conducting research on recycling spent basic refractory materials as EAF slag conditioners. A good foaming slag should be a creamy, MgO saturated slag, which contains some solid particles (MgO-FeO). A computer model was developed to calculate the dual saturated slag chemistry with respect to CaO and MgO, the MgO saturated slag chemistry, and the solid content in solution. The effects of C/S ratio, AhO3 and temperature on the MgOsaturated slag as calculated by the model will be discussed.

Jan 1, 2000

By Uday Pal

In direct reduction processes for iron and steel making, significant amounts of Fe-C alloy droplets are generated and these remain suspended in relatively low FeO (around 5%) containing slags. Earlier workers have found that when the FeO content in the slag is <5%, the decarburization reaction becomes extremely slow (virtually ceases to occur) even though the alloy droplet contains a significant amount of carbons (2-3%). Understanding this rate controlling kinetic phenomena is crucial to designing an&apos; optimum direct steel making process. We studied decarburization of Fe-C particles by low FeO (<5%) containing CaO-SiO2A12O3 slags and found that by putting both the droplet and the slag in direct contact with an inert electronically conductive member that extends deep inside the slag bulk were able to quickly and completely decarburize the droplets. A detailed description and an explanation of the process will be presented.

Jan 1, 1995

By Yuanbo Zhang, Yingming Chen, Zijian Su, Bingbing Liu, Jun Chen

Iron, tin-bearing tailings is a kind of hazardous solid waste generated from cassiterite dressing operation. It is difficult to utilize the tailings by present mineral processing methods due to the complex dissemination characteristics. In this study, a process of gas-based magnetizing roasting followed by magnetic separation was studied for separating and recovering iron from the tailings. The effects of roasting and magnetic separation parameters on the recovery of iron were systematically investigated. The optimum parameters were proposed as follows: CO/(CO+CO2) content of 5%, roasting temperature of 850 C, roasting time of 60 min, grinding particle size of 90% less than 45 μm and magnetic field intensity of 800 Gs. Under these conditions, the magnetic concentrate containing 68.5% Fe and 0.06% Sn was achieved, which can be used as high-quality raw materials for direct reduction iron production.

Jan 1, 2016

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By Ali Nadir Khan

Depleting copper resources and advancing technologies have challenged industries to develop more viable, adaptable and cost efficient processes using also secondary raw materials in copper production. This study is targeting to that goal by dynamic modelling of flow and heat transfer coupled with chemical kinetics in an industrial scale flash smelting furnace settler using commercial CFD software ANSYS Fluent. First, different physical phenomena occurring inside the settler, for example, settling and separation of the matte/slag phases, and heat transfer between slag/matte phases and settler walls are studied. Secondly, reaction kinetics between matte and slag, and between slag/matte and settler walls, and impurity element distribution will be studied. This would also include phase changes phenomena due to these reactions and the flow of the reaction gases inside the settler. Settling of polydispersed droplets, their coagulation, breakage, and WEEE particle behavior are further targets of the modelling work.

By Lee Fergusson

"The primary features of ViroMine™ Technology are introduced and applications of ViroMine™ Technology to mine site remediation and the treatment of a variety of intractable waste-streams, including a technical discussion of acid neutralizing capacity, metals binding capacity and longterm stability of results. Outcomes from four applications at high-profile international mine sites are presented: 1) the superfund site at the Gilt Edge Mine, South Dakota, USA (four years of data on the treatment of acidity, TDS and metals such as Al, Co, Fe, Mn and Zn); 2) one of Australia’s most polluted sites at King River Delta in Tasmania (treatment of TAA and TPA, and metal and metalloid contaminants such as As, Cr and Hg); 3) The Aljustrel “Aqua Forte” mine site in Portugal (high acidity, metal and metalloid contaminants such as Al, As, Cu and Zn) and 4) the Ulsan Iron Ore Mine at Ulsan, South Korea (treatment of metal and metalloid contaminants such as As, Cd and Ni).IntroductionThe commercialisation of ViroMine™ Technology has resolved some of the most intractable pollution issues associated with historic mining ventures on a global scale and has facilitated the neutralisation of Acid Rock Drainage (ARD), remediation of acidic and metal contaminated impoundments (including tailings dams) and promoted revegetation on tailings deposits and waste rock dumps. ViroMine™ Technology also enables current mining ventures to manage effluent simply and efficiently to meet increasingly stringent environmental standards and is enabling the mining sector to reconceptualise the management of mine spoil. The abilities of ViroMine™ reagents to neutralise the actual and potential acidity of sulphidic mine spoil coupled with the ability to bind metal and metalloid contaminants into non-bio-available forms are the key features delivering environmental and economic benefits to the mining sector and the broader community. Results from four projects utilising ViroMine™ Technology are presented to highlight the suitability of ViroMine™ Technology to treat all forms sulphidic mining wastes. 37"

Jan 1, 2008

By Rak-lun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEDs. Efficient blue light-emitting diodes (LEDs) were fabricated using InGaN/GaN triangular MQWs. The LEDs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEDs at 20 mA and 20 °C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LED, but decreased substantially in the rectangular one.

Jan 1, 2003

By Takeo Fujino, Nobuaki Sato, Junichi Hasegawa, Masato Nakazawa, Kohta Yamada

"Tantalum oxide thin films were deposited on quartz substrates by laser ablation of Ta2O5 target using Nd:YAG pulse laser. Deposition-was observed when a laser light energy higher than 200 mJ and its repetition rate higher than 3 Hz. A thin film of 0.1 µm thickness was obtained by the ablation using a laser light of 300 mJ and 6 Hz for 2 sec. The thickness of the film increased with increasing energy, repetition rate and irradiation time of laser. By the SEM observation, it was found that many island-like particles were deposited on quartz substrate forming a thin film. The obtained thin film, which was identified as ? Ta-O by X-ray diffraction, was oxidized to Ta2O5 by the heat treatment in air at I273 K for 3 h.IntroductionTransition metal oxides have a potential to show special characteristics in electrical, magnetic and/or optical properties. When such compounds are fabricated in the form of thin film, the special properties would be improved or new characters would appear in comparison with bulk materials. Tantalum penta-oxide is widely used as a capacitor since Ta2O5 shows high dielectric constants up to high temperatures. The tantalum solid capacitor has been fabricated by the electrical oxidation of sintered Ta metal cylinder followed by MnO2 film coating. However, further improvements, reduction and layered structure formation, are required for compacting the devices. The layered structure of thin films would be applicable for the above requirements. The formation ofTa2O5 film by low pressure CVD1), photo CVD2) and magnetron sputtering3l were reported. The laser ablation -method is one of the most convenient techniques for the deposition of thin films from their compounds, such as oxides. Formation of Ta2O5 film by pulse laser deposition (PLD) method using ArF excimer4), Nd:YAG (533nm)5) and TEA CO2 6 lasers was reported. In these PLD studies, ablation was carried out in relatively high oxygen pressures resulting in formation of Ta2O 5 film. In this paper, the deposition of tantalum oxide thin film by the laser ablation of Ta2O 5 using Nd:YAG pulse laser was examined at a viliety oxygen pressures ranging from 10-8 to 10 Torr. The morphology of the films was also investigated in relation with substrate temperature and oxygen pressure."

Jan 1, 2000

By B. C. Jena

Activities of carbon, cobalt and nickel were evaluated in the ternary systems iron-carbon-cobalt and iron-carbon-nickel for the temperature range 1300-1600°C for cobalt and 1300-1700°C for nickel. The carbon activities were determined from the knowledge of activities (1) in the binary system iron-carbon, (2) in the dilute ternary systems and (3) from the knowledge of carbon saturation data. The activities were mathematically expressed with the Taylor series expansion of Wagner&apos;s interaction parameter formalism modified to suit concentrated solutions. The cobalt and nickel activities were determined from the knowledge of carbon activities by applying the Gibbs-Schuhmann integration and from cobalt and nickel activities in the binary systems iron-cobalt and iron-nickel. Partial molar enthalpies of mixing were determined based on the temperature behaviour of the activity coefficients.

Jan 1, 1992

By F. Ríos

Fundamental research, at laboratory scale, on the biomass adsorption capacity of a liquid mining effluent has been done. The biomass used corresponds to a Chilean seaweed called Gracilaria chilensis. The waste water effluent corresponds to clear water coming from thickeners of a Chilean copper mining operation. The biomass was dried, washed, treated with an acid solution, and then reduced in size. A characterization of Zeta potential was made, finding negative values in a wide pH range with a ZPC equal to 2.5 1. Adsorption tests were made- in an agitated system containing an artificial solution of CuS04 at a controlled temperature of 25 degrees Celsius; also, the effect of pH over the copper adsorbed was studied. Maximal adsorption of copper was found at pH equal to 6, and the Langmuir model indicated values for saturation of 52.08 mg/g and for standard free energy of about -21 KJ/mol. Kinetic adsorption was very high and fitted very well with a second order model equation, finding that 90 per cent of the adsorption occurred during the initial 10 minutes. After stoichiometric when 1 mol of copper is adsorbed, 2 mol hydrogen are released, showing that the main mechanism to remove heavy metals is the ionic exchange, and the seaweed ensures total discharge of copper adsorbed when the pH value is about 1. Experiments done with real waste water from thickeners lead us to conclude that optimal results for copper and molybdenum adsorption are at pH around 3.25 and the remaining treated water may be partially discharged into the water currents, thus showing that Gracilaria chilensis can be used to remove heavy metals easily from liquid effluents in the copper mining industry.

Jan 1, 1999

By D. A. Milligan

Ammonia leaching of copper sulfide concentrates, matte, scrap or other sources of copper yields copper amnine sulfate solutions which are converted to metal in a two-stage process involving precipitation of inter- mediate sulfites and their thermal decomposition to copper powder of high purity. Processing details and results are given. Considerable simplification in circuitry and cost savings are indicated. Energy requirements are reduced by substitution of copper powder precipitation and ammonium sulfate crystallization for solvent extraction, electrowinning and lime boil.

Jan 1, 1976