Search Documents

By Susanne Pignolet-Brandom

Reflected light microscopy, and scanning electron microscope energy dispersive spectroscopic analysis and backscatter electron images were used to determine if a "slick dross" with undesirable handling properties has an assemblage of phases distinct from normal dross. This study has found that in the normal dross the most abundant lead phases are lead sulfide and lead metal and the most common copper phases are copper-iron sulfide and copper sulfide. In the slick dross, the most abundant copper phase is copper-lead sulfide and the most common lead phases are copper-lead sulfide and lead sulfide. The resulting mineralogical information has provided additional insight into the causes of the handling problem and the reaction mechanism for the formation of normal and slick dross

Jan 1, 1988

By Yuanbo Zhang, Zhixiong You, FENG ZHOU, Guanghui Li, Zhengwei Yu, Zhiwei Peng

Reduction disintegration of sinter significantly affects the coke consumption and productivity of blast furnace smelting. As we know, the reduction disintegration index (RDI+3.15) of sinter obtained from titanomagnetite concentrate is relatively worse than those from ordinary iron ores. In this study, the effect of sintering parameters, mainly involving coke breeze dosage and basicity on sintering indexes was investigated using titanomagnetite concentrate as raw material in an experimental-scale pot. Subsequently, RDI+3.15 of the sinter was detected according to the Chinese standard of GB/T13242-91. The results show that RDI+3.15 rises with the increase of coke breeze dosage, while it decreases with increasing basicity from 0.5 to 2.0 and then increases in the basicity range of 2.0-3.0. Finally, the microstructure of sinter before and after reduction was studied. And the mechanism of reduction disintegration was preliminary revealed by analyzing the morphologies and distributions of minerals in the sinter.

Jan 1, 2015

By I. J. Moon

The reduction behavior of hematite by H2 and H2-CO gas mixtures was investigated to elucidate the reduction mechanism at 800-950 °C. The hematite compacts were made by Cold Isostatic Pressing to produce compacts of uniform shape and size. The compacts were sintered at 1000° C for 30min, and showed a contraction of 29%. Mercury pressure porosimeter was used for measuring the total porosity, pore size distribution and pore surface area of the compacts. Reduction was measured by means of weight-loss technique using Cahn Balance (Model : TG-171, capacity log, accuracy f 10pg). Microscopic examination and X-ray analysis were used to correlate the structure of reduced compacts with the mechanisms of reduction. Neither chemical reaction control nor diffusion control is adequate in describing the complete course of reduction of the hematite compact. The reduction of hematite compacts was initially controlled by the chemical reaction at oxidelmetal interface. The reaction goes through a transition phase .where it is undergoing a mixed control, followed by the diffusion control towards the end of the reduction. The values of apparent activation energies for chemical reaction control were 3.48-8.43 kcal/mol depending on the gas compositions.

Jan 1, 1997

By N. V. Gorelikova

A new type of zirconium mineralization has been recognized in the Devonian volcanic rocks from an orogenic depression in the Central Kazakhstan. The most characteristic features of this deposit are the fine-grained nature of the zirconium mineralization, an unusual texture of the zirconium ores, and a close association of zirconium with phosphorus in the ores. Zircon grains form fine globular aggregates with the features of hexagonal crystal habit. In addition to crystalline zircon, the ores contain metacolloidal zircon, similar to hydrozircon. The morphological and textural features of the zirconium ores suggest that the deposition of ore deposits took place at a low temperature from colloidal solutions. It is believed that this deposit should be considered to be a new type of zirconium mineralization that is related to low-temperature hydrothermal processes.

Jan 1, 1995

By Makoto Suzuki

After hot rolling, stainless steel strip is processed by the Hot Rolled Annealing and Pickling line (HAP) , where H2SO4 or mixed acid of HNO3 and HF is normally used. In the pickling bath, metal oxide accumulates in the form of sludge, which should be removed from the bath regularly. A new automatic continuous sludge disposal system has been introduced at Chiba Works of Kawasaki Steel Corporation to increase sludge removal efficiency and improve the working environment. The elements of the equipment are as follows. a. Ejectors in pickling bath: to carry the mixed acid into the circulation tank through the piping system. b. Sedimentation bath : to sediment sludge out of the bath. c. Skip conveyer : to convey a specified volume of sludge into a kneading for device for neutralizing. The sludge removal efficiency of this system is very high. and the volume of sludge accumulation in the pickling bath has substantially decreased.

Jan 1, 1996

By Mim Li, Huimin Lu, Lisha Yang

"CuInS2 thin films solar cells have drawn much attention for their low-cost, stability and high conversion efficiency. The electrodeposition of Cu-In precursor films, as the first step in making CuinS2 solar cells electrochemically in the air-and water-stable ionic liquid based on choline chloride/urea eutectic mixture has been investigated at constant potential. Compared with aqueous electrolytes, the large electrochemical window as well as the high thermal stability of this ionic liquid allow the direct electrodeposition of Cu-In precursor films. Then the precursor films were sulfuretted in a tube furnace at different sulfurization temperatures to optimize the films properties. The films obtained were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS).IntroductionCuInS2 is one of the most prospective absorber materials for low cost thin film solar cells, with a high conversion efficiency that exceeds 32% in terms of theory and nearly 13% in laboratory level [1-2]. In addition to its long-term stability, CuinS2 has a band gap energy Eg ranging from 1.3 to 1.55 eV and an optimal optical absorption coefficient reaching 105cm-1 [3-4]. CuinS2 thin films have been prepared by several methods such as spray pyrolysis [5-6], r.f.sputtering [7], vacuum evaporation [8-9] and electrodeposition. Comparing with vacuum methods, electrodeposition has lots of advantages such as less energy consumption, preparation big area thin film, stable system and enabling cheaper films.The electrodeposition of most technologically important metals has been shown to be possible from a wide range of ionic liquids. These ionic liquids are currently applied in a wide variety area. It is reported that the cell efficiency of chalcopyrite absorber layer (CIS, CISeS, and CIGS) via an electrodeposition route in laboratory condition has reached 11.3% [10]. Copper and indium alloy film is regarded as important precursor for the production of compound semiconductors with sulfur. The electrodeposition of the alloy film from room temperature ionic liquid (RTIL) has not been widely investigated. Only few alloy films, such as ZnTe, CdTe, GaAs and AlSb have been electrodeposited."

Jan 1, 2011

By Guo Chen, Jin Chen, Jinhui Peng

"In this paper, the methods of life cycle assessment for microwave hot air systems, and the concept of green degree were proposed. Greenness evaluation index, evaluation system and evaluation model of microwave hot air systems were established. Also, life cycle assessment processing based on these ideas was introduced. Analytic hierarchy process and fuzzy decision- making method were utilized to establish and solve the greenness evaluation of assessment model, while the scores of green degree in microwave hot air systems were obtained. The results show that Life cycle assessment can be applied effectively and efficiently to the microwave hot air systems.IntroductionHot air systems are an important industrial operation condition, which is used to provide high temperature air for materials processing. Nowadays, high temperature airs are manufactured by the conventional heating processes, in which some ceramic materials are used as heating materials. However, these processes pollute the environment. Therefore, to explore new method to produce high temperature air with low energy consumption and less environment pollution are necessary.Microwaves are now being used in various technological and scientific fields in order to heat dielectric materials [1]. Microwaves irradiation has been explored in materials processing in recent years [2-3]. The main advantage of using microwave heating is that the treatment time can be considerably reduced, which in many cases represents a reduction in the energy consumption as well. Since there is energy absorption but no heat conduction, the heating is very rapid and highly efficient, resulting in energy savings and the shortened processing time [2, 4]. Compared with conventional heating techniques, the additional advantage of using microwave irradiation is that microwave irradiation achieves both internal and uniform heating [5-7]. In addition, it is more convenient to control the microwave irradiation processing, because of no direct contact between the heating source and heated materials with less equipment size and waste [2, 8-9]. Life cycle assessment is used and accepted methods for the evaluation of the environmental impacts of products or systems [10]. Recently, many appropriate evaluation methods have been developed for life cycle assessment [11-12]. These proposed methods usually are employed for the evaluating product and analyzing results [13]. Among them, the analytic hierarchy process and the fuzzy comprehensive evaluation stand out as a popular method utilized in many fields [14-16]. Analytic hierarchy process and fuzzy comprehensive evaluation are a combination of mathematical and statistical technique that is useful for analyzing the effects of several independent assessment aspects on the system goal without the need of the predetermined relationship between the objective function and the assessment aspects [17-19]."

Jan 1, 2013

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In tungsten ion-exchange process, excessive sodium impurity enters into ammonium tungstate solution. However, the Na content of the final ammonium paratungstate (APT) product must be strictly controlled. Consequently, it is necessary to remove Na from the ammonium tungstate solution during processing in order to obtain the required purity of APT. In this study, porous Na specific absorbent, Na1+xAlxTi2−x(PO4)3, is used to remove Na from the ammonium tungstate solution. Through experiments, the effect of reagent concentration of Na1+xAlxTi2−x(PO4)3, reaction time, reaction temperature and Na concentration on the Na removal were investigated. The results showed that under optimal reaction conditions of reagent amount of NATP 1.0 times of theoretical amount, reaction temperature 25 °C and reaction time 15 min, the Na removal from commercial (NH4)2WO4 solution can reach 98%. Na1+xAlxTi2−x(PO4)3 has a good applicability to different Na+ concentrations. The obtained APT product reaches the national standard purity of zero level.

Jan 1, 2014

By A. Treverrow, G. A. Brooks, H. K. Worner

"The work by H.K Worner and co-workers at CRA in the 1960s, and early 1970s, established that molten metals could be refined continuously utilising counter current flow of metal and slag. Womer also demonstrated that counter current refining could produce highly refined metal products. These developments coincided with the advent of high intensity metallurgical reactors in both the ferrous and non-ferrous industries (e.g. BOS, Q-BOP and later Sirosmelt) that utilised high levels of gas injection to produce rapid stirring and very fast reaction. These new generation of high intensity metallurgical reactors allowed high tonnage rates through relatively small volume vessels.Whilst, it is well known that the counter current flow of reacting phases offers the potential of efficient mass transfer and high purity products, the application of counter current reactors to molten metal/slag systems has been criticized on the basis that they suffer from either low intensity or, alternately, from poor refining due to excessive dispersion. These criticisms relate to the balance between intensity and the refining capacity of a reactor. That is, whilst high levels of mixing transversely to the direction of flow promotes high mass transfer, longitudinal mixing (dispersion) is detrimental to refining. Of course, mixing in one direction invariably leads to mixing in other directions, thus creating a playoff between high mass transfer and excessive dispersion.This balance between intensity and refining has been the subject of recent studies overseas, and at"" the University of Wollongong, using cold modelling techniques to evaluate the effect of mixing on dispersion in a counter current refining launder. These studies have shown that for a given geometry and mixing regime, dispersion decreases with increasing flow of liquid phases. This means that whilst high mass transfer cannot be achieved in a refining launder without sacrificing the degree of refinement, there is no impediment to achieving high productivity through such a system, in fact, high through puts may favour good refining. Thus, it may be possible to match a high productivity smelting operation with a equally productive counter current refining stage."

Jan 1, 1996

By Denise Cristina de O. Nascimento

Natural lignocellulosic fibers are increasingly being used as polymeric matrix composite reinforcement owing to economical and environmental advantages as renewable and biodegradable materials. Among these, the piassava fiber extracted from a palm tree native of South America stands as one of the most rigid with a potential to be used as composite reinforcement. Therefore, the present work investigates the notch toughness behavior, by Izod impact tests, of epoxy composites reinforced with up to 40 % in volume of continuous and aligned piassava fibers. It was found that the incorporation of piassava fibers results in significant increase in the impact energy of the composite. Scanning electron microscopy analysis showed that the nature of the piassava fiber interface with the epoxy matrix is the major responsible for the superior toughness of the composite.

Jan 1, 2009

By Denise Crocce Romano Espinosa, Andrea Moura Bemardes, Jorge Alberto Soares Tenorio, Daniella Cardoso Buzzi, Tatiana Scarazzato

"In copper plating processes, a fraction of raw materials are incorporated to the final products, while other portions are discarded as effluents. In this study, the application of electrodialysis (a membrane treatment process) was studied for treatment of wastewaters from cyanide-free strike baths, in order to reuse the components of this bath: copper and HEDP. The synthetic solutions studied consider 1 % of ion concentration of the bath used in this process, simulating the rinsing waters to be discarded. The electrodialysis allowed a percentage extraction up to 73% of copper ions and 72% of HEDP from the effluent. Complexes formation between the acid and copper indicates the possibility of recovery of components in the same compartment, obtaining a concentrated solution of these substances that can be reinserted in the process, for compensating drag-out losses. A diluted solution is also obtained, that can be reused as water in rinsing tanks.IntroductionIn metal finishing industries, contaminants in wastewater and the type of treatment required are determined according to the type of operation [l]. Generally, electroplating industries employ conventional wastewater treatments, e.g. oxidation of cyanide and chemical precipitation. This stage promotes reactions with soluble compounds to produce an insoluble precipitate, removed by physical separation. The sludge is dried by press-type filters [2].In this manufacturing sector, part of the raw materials are discarded as hazardous waste. The cost of discarded compounds and the treatment and disposal of waste may compromise profit margins. In addition, water consumption per unit of production stimulates the development of methods able to recover and reuse the largest possible amount of water [3].In some plating processes, cyanide-based substances are used as complexing agents and as raw materials in form of metal salts [4]. However, the toxicity associated with cyanide has been promoting research for the development of new raw materials in plating processes.A study conducted in Brazil [4] evaluated the modification of a commercial cyanide-free bath for processes of copper coating on Zamak. In the performed study, a new alkaline copper bath was formulated using l,hydroxyethane-1,1-diphosphonic acid (HEDP), an organic compound known for forming stable complexes with metal ions.As results of the study, the operational conditions and the formulation of a bath to obtain adherent, uniform and bright layers were established (Table I) [4]."

Jan 1, 2014

By P. A. Treasure

The EMEW® cell has been developed to overcome a number of inherent limitations in conventional electrowinning technology, particularly the high cost and restricted process windows characteristic of conventional hardware. The technology has been widely demonstrated to achieve high performance for various metals under chemical conditions well outside the limits required for efficient operation of conventional cells. This process flexibility offers significant opportunities for cost savings. in recovery of zinc from primary and secondary sources. The EMEW® technology is now available on a fully engineered basis, as a versatile commercial alternative to conventional electrowinning hardware. Application of the EMEW® cell for recovery of secondary zinc material offers significant advantages to the recycling industry. For example, a selective caustic leach can be used where there are high levels of iron or other contaminants in the target material. The reagent requirement is minimal as most of the caustic is regenerated in the bell and zinc dust that may be required for electrolyte purification is produced in the cell. A high purity zinc powder or cathode is produced in the cell. In the case of acidic zinc electrolytes, the cell is capable of operating over a much wider range of operating conditions than a conventional cell.

Jan 1, 2000

By Janene Barter

Telfer Gold Mine treats both gold/copper oxide and sulfide ores in a remote location in the Great Sandy Desert, Western Australia. Currently, the oxide gold ore is treated in a conventional CIL circuit by blending the low and high grade copper ores to minimise cyanide consumption and allow smooth operation. The sulfide ore is treated through a flotation circuit to produce pyrite and copper concentrates. The pyrite concentrate is treated in the CIL. Copper concentrate is stockpiled and sold to a smelter for further processing. In recent times, as the depth of the pit has increased the copper head grade has also increased, to the point where the ore was becoming uneconomical to treat. In addition, it was desirable to reduce the amount of cyanide reporting to the tails dam both from an environmental and economical viewpoint. Newcrest Mining Limited engaged GRD Minproc Limited to evaluated a process to reduce the amount of cyanide entering the tail dam with consideration given to copper recovery. From this investigation, the Sulfidisation, Acidification, Recycle and Thickening (SART) process was selected. A detailed testwork program for SART was undertaken with the objective to design and construct a SART plant at Telfer. This paper outlines how the SART process was chosen and summarises the testwork that led to the design of the SART plant. It also touches on some of the important issues for designing this type of process.

Jan 1, 1998

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By W. Gutmannsbauer

Thin films of TiO2 nanoparticles have been prepared by different reactive deposition methods, such as electron evaporation, ion plating and ion beam sputtering. Many properties especially the optical properties, are strongly related to the film morphology and surface roughness. Scanning force microscopy was employed to obtain information on the surface structure of as-deposited Ti(h thin films. The influence of the deposition conditions and the film thickness on the optical and structural properties has been investigated. The as-deposited films were found to be amorphous or polycrystalline with anatase structure.

Jan 1, 1995

By Artur R. P. Junior Sergio, Pedro A. Netto, N. Monteiro, Foluke S. de Assis, Frederico M. Margem

Synthetic fibers are being replaced gradually by natural materials such as lignocellulosic fibers. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as environmental and economic. So there is a growing international interest in the use of those fibers. The banana fiber presents significant properties to be studied, but until now few thermal properties on banana fiber as reinforcement of polyester matrix were performed. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity for polyester composites reinforced with banana fibers. In the polyester matrix will be added up to 30% in volume of continuous and aligned banana fibers. These values show that the incorporation of banana fibers in the polyester matrix changes its thermal properties.

Jan 1, 2015

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016

By Wenjun Duan, Kun Wang, Qingbo Yu, Qin Qin

"A novel oxygen production technology noted chemical looping air separation (CLAS) was introduced and properties of Cu-based oxygen carriers used were investigated. The oxygen carriers were prepared by mechanical mixing. Al2O3, Fe2O3, ZrO2, TiO2 and SiO2 were used as binders during the preparation. XRD patterns show that spine! oxides are formed using Al2O3 and Fe2O3 as binders. Phases of CuO and binders keep stable using ZrO2, TiO2 and SiO2 as binders. BET values of oxygen carriers increase in the order of ZrO2>TiO2>SiO2>Fe2O3>Al2O3. The effects of temperatures, binders, particle sizes and flow rates on reduction/oxidation reaction rates were studied in TG experiments. The reduction reaction rate increases in the order of ZrO2>TiO2>SiO2. The effect of binders on the reactivity of oxidation is not obvious. The reduction and oxidation reaction rates both have the tendencies of increasing with the temperature increasing and with gas flow decreasing. However, the effects of gas flow and particle size are little.IntroductionChemical looping air separation (CLAS) is a novel oxygen production technology. The oxygen carriers used in CLAS release oxygen in reduction reactor and regenerate in the oxidation reactor. Selecting suitable oxygen carriers is the key for CLAS. Oxides of CuO, Mn2O3, Co3O4, Pb3O4, CrO2, SrO2, PdO2 and CeO2 have the property of releasing oxygen at suitable temperature and oxygen partial pressure [1]. Among these oxides, CuO, Mn2O3, Co3O4 are the most common compositions used to prepared oxygen carriers for chemical looping combustion (CLC) or chemical looping with oxygen uncoupling (CLOU) [2-5]. Moreover, thermodynamic calculations and preliminary experiments were carried out on oxides of Cu (CuO/Cu2O), Mn (Mn2O3/Mn3O4) and Co (Co3OJCoO) by Moghtaderi to ascertain their feasibility for CLAS process [6]. CuO has the highest oxygen transport capacity (0.1 g 02/g CuO compared to 0.03 g 02/g Mn2O3 and 0.06 g 02/g Co3O4). However, agglomeration is the biggest issue for copper oxides used at high temperature because of its low melting point (l 450°C for CuO, 1235°C for Cu2O and 1075°C for the mixture of CuO and Cu2O) [7]. In order to improve the capability of anti-sintering and stability ofCuO, binders (ZrO2, MgAl2O4, TiO2, SiO2, Fe2O3, Al2O3, cement) are added during the preparation of Cu-based oxygen carriers [8]. In this paper, the Cu-based oxygen carriers were prepared by mechanical mixing method. TiO2, Al2O3, Fe2O3, ZrO2 and SiO2 were selected as binder. XRD, BET and SEM were used to analyze the phase, surface area and surface morphology of oxygen carrier prepared. The reactivity of oxygen reduction and oxidation of oxygen carriers prepared were investigated in STA409PC thermal analyzer."

Jan 1, 2014

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The clean utilization of the residue containing chloride, CuCl residue, produced from zinc hydrometallurgy is very important for the recycle of valuable metals. And drying is the main process in recycling. In this study, response surface methodology was used to optimize operating conditions of the drying of CuCl residue in a convection oven and desirability function used as the methodology for the optimization. Optimization factors were air temperature (80–100°C), material thickness (10–25mm) and process time (80–120min) while investigated responses was final moisture content. The optimum conditions were found to be the temperature of 95.48°C with the material thickness of 13.47mm for the process time of 89.48 min. Under optimum conditions, the predicted moisture content of CuCl residue was 4.11% while the experimental date was 4.13%. The experimental value after process optimization was found to agree satisfactory with the predicted value. After drying, XRD was used to analyze the main phases of CuCl residue. The CuCl residue is made up of CuCl,Cu2O, ZnS and other compounds.

Jan 1, 2015

By Lin Li, Xiang Li, Yifang Zheng, Jilai Xue, Jun Zhu

"Al drops and gas bubbles in the anode-cathode space of aluminum electrolysis cell are of great importance for cell operation improvement in metal loss, current efficiency and energy consumption. A direct observation on the Al drop, gas bubble and ultrasound was carried out through a see-through cell. The Al drop immersed into the cryolitic melt was found moving up and down irregularly in the anode-cathode space without electrolysis, which was then completely dissolved into the melt. During electrolysis, the Al drop came to the anode area and reacted with the gas bubbles generated on the anode. Under ultrasound, the gas bubbles were removed from the anode surface while the Al drop was kept on the side of anode. The observed phenomena were useful for technology improvement in reducing the anode-cathode distance or lowering the energy consumption in aluminum electrolysis.IntroductionDuring aluminum electrolysis, aluminum metal drop and anodic gas bubble are in close contact each other within the anode-cathode space, and the interaction between them can produce significant impact on metal loss, current efficiency and energy consumption. The motions of the Al drop and the gas bubble are also related to the dissolution of aluminum metal into cryolitic melt and the cell voltage drop due to the bubble layer covering the anode surface.A number of studies have been carried out using different types of see-through cells, where the dissolving process of metal Al into cryolitic melts (metal fog) in the anode-cathode space was directly observed and photographed [1, 2]. With the similar method, some direct observations on the anodic bubble behaviors with and without ultrasound were performed during aluminum electrolysis [3-6]. However, to our best knowledge, there is no published work on direct observation on the behavior of Al drops and anodic gas bubbles staying together within the same anode-cathode space, as well as the motion and interaction of them in cryolite-alumina melts."

Jan 1, 2011