Search Documents

By Linsheng Xu

When coal seam is under the integral thick sandstone (or conglomerate), the structure of thick sandstone is integral and its strength is rather high. After coal is extracted, the roof is hanging and caving is difficult. When the method of full caving is adopted in the longwall working face to control this kind of hard and difficult caving roof, the effect of roof-controlling affects directly the production and safety. In China Datong Coal Mines the extracting coal deposit is Datong Jurassic period. Most of the roof is sandstone and conglomerate. It is hard and difficult to cave. Having used special hydraulic power supports and other special ways to deal with the roof, the hard and difficult caving roof has been controlled.

Jan 1, 1986

By Ernest A. Curth

An estimated 49 billion tons or 29 percent, of the coal reserve base to a depth of 1,000 feet in the eastern United States fall in the 28- to 42-inch range. Often left out as a consequence of selective mining, it is a paramarginal source that will become increasingly important. At present, all active thin seam longwalls are located in the Eastern Coal Province, and a number of operations have been suspended due to the erosion of the market for metallurgical coal. Extensive premining studies, appropriate mine planning, reliable equipment that is designed with ergonomics in mind, adequate roof support, intensive training, and strong face discipline are the ingredients that provided a measure of consistency in production for the last 10 to 16 years, particularly in the Pennsylvania bituminous coalfield where single drum shearers dominate. Plows, which were found to be very productive in suitable strata in Europe, are used in the Pocahontas field. Low seam four- and six-legged shields have been introduced recently. The future holds automation at progressive levels. The first step is batch control with the benefits of quickly applied roof support and reduction of workmen exposure to environmental hazards.

Jan 1, 1981

By Liang Yinhuai

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover-caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By P. K. Kaiser

The purpose of deformation monitoring for the evaluation of the stability of underground openings is reviewed briefly and some results from laboratory tests of small tunnels are presented. The ground behaviour is described by comparison with the response of structural systems and illustrated by the data from the testing of small tunnels. It is concluded that the main objective of a deformation monitoring system for stability evaluation is to determine the actual process of deformation and instability in the area surrounding the opening. Only when this process has been established is it possible to use deformation measurements to design support systems or to improve construction or mining procedures. Present monitoring practice is not sufficiently orientated toward the aim of process description.

Jan 1, 1981

By Y. P. Chugh

The use of wooden supports, supplementary to the primary method of roof control using roof bolts in mines, consumes over 3 million cubic meters of hardwood in the U.S. annually. These supports arc primarily used in the form of cribs and posts. Along with a rapid depletion of high quality timber resources, supplies fluctuate seasonally, costs are escalating rapidly, and product quality is highly variable. Environmental considerations of global climate change put additional pressure on deforestation for utilization of timber for artificial supports. On the other hand, management of coal combustion byproducts (GCBs) from power plants has become a major issue to maintaining a healthy coal industry. The USA currently produces over 100 million tons of CCBs annually and the average cost for their management in the US is about $20/ton. This cost is expected to escalate rapidly with tougher environmental regulations. The principal author has been directing research, development, and demonstration studies for CCBs-based artificial supports and lightweight structural materials in mines for the past seven years and has made significant progress toward commercially viable products. More specifically, first and second generation crib elements and post elements have been developed, characterized analytically, and demonstrated in the field. It is estimated that about 2.5 x 10" tons of fly ash could be utilized for artificial supports in U.S coal mines and this would double if these materials were utilized in non-coal mines as well. The author believes that CCBs-based artificial supports have the potential to replace wooden supports and blocks with better performance and cost competitiveness while managing CCBs in an environmentally sound manner. This paper focuses on the development and field demonstration of CCBs-based artificial supports for use in underground mines, and its pilot scale fabrication facility. Recent analysis results on engineering performance evaluation of the developed crib under various loading conditions using finite element method are presented. The following comments highlight the developments: I ). Engineered artificial supports, crib and post elements, using CCBs as a major constituent, have significant potential for application in mines because their structural performance is significantly better than wooden cribs counterparts. 21. Engineered crib elements provide about 50% larger area for air-flow than a conventional wooden crib. 3). Engineered crib elements are not flammable. 4). Each engineered crib element utilizes about 10 kg of fly ash, about 40 % of the weight of crib element- Therefore, a typical crib 2.0 m high utilizes about 200 kg of fly ash. 5). Each 16.5 cm diameter engineered post utilizes 50 kg of fly ash. 6). Assuming 3.0 million cu. meter of wood consumed for post and crib support systems, it is estimated that about 4 - 5 million tons of fly ash may be utilized for supports fabrication in the USA. 7). An engineered post has excellent post-failure characteristics similar to wood. In addition, the engineered post also has excellent loading and unloading characteristics close to the yield point of about 75% of the ultimate load carrying capacity.

Jan 1, 2004

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By C. Tom Blevins

The purpose of this paper is to discuss production and roof control problems associated with directional lateral stresses in an in situ stress field and the approach that Inland Steel Coal Company made in trying to cope with them. Before proceeding, a description of the mine location, product, geology, restraints, and mine history is in order. The mine is located in Hamilton County in Southeastern Illinois. It produces a high volatile metalurgical coal and is slated to produce 2.1 MTY. Product ion is in the Illinois No. 5 seam at a depth of 930 feet, approximately 490 feet below sea level. The scam height averages from 5.5 to 6.0 feet throughout the reserves with height increasing in the eastern reserve area to approximately feet and a 5 Foot average in the West. The scam tends to dip to the North, North East, but is locally very undulating. The Galatia channel washout outlines the eastern boundary of the reserves and there is a split coal area toward the central part of the property than runs south-southeast. The top above the #5 seam is laminated medium gray shale called Dykersburg. Individual shale bedding planes vary locally From ½ to 1" in thickness to a more normal thickness of 1 to 1 ½ with some areas being interlayed by thin carboncous material. The top normally must be considered as materially competent. Even though the mine is still relatively small in area with only 1.3 million tons of total production to (late, we have encountered dense zones of slicker sides and premining, stress cracks (joints). There are also areas of siltstone, that vary from a few inches to several feet thick, and areas of rider coal, clay instrusions, and rolls. We have crossed lineament concentrations that show strong evidence of corelation to localise top problems. These are being monitored closely to see their predictability on our present and future mining conditions. The face cleat runs N 55° E and butt cleat runs S. 25° E. On a regional basis, there are several anticlinal belts that trend in a northerly direction. The one major restraint is that Inland does not own surface subsidence rights. Therefore, a partial extraction mining plan is being followed. The Holland-Gaddy formula for pillar strength design is used to calculate theortical pillar sides. When production began in March of 1979, it was noted that ground control problems occurred as we drove north entries. East-west cross cuts tended to have better working conditions. This phenomia occurred from a couple hundred feet, but seemed to dispate as we got away from the men and material shafts. Once the production shaft was connected and enough entries extended for installation of belts, ground control problems were again experienced in north-south headings. It was also observed that when mining north-south headings with east-west crosscuts, if the crosscut was driven through ahead and supported, the intersection was stable upon entry connection. This held true even where fairly extreme ground control, problems were encountered. The reverse held true. when driving east-west headings with north-south crosscuts. At this time, we started searching in earnest for a working theory to explain this roof phenomia. It also became the first step of what eventually was a four step sequence to derive a workable solu¬tion to the problem. The combination of the many geological changes and the fact that north-south condition was at times intermitent, helped to disguise the stress field. The mine also being in a fairly virgin area with no mines in approximately 25 milt, radius, meant we didn't have a reliable case history to examine. Various theories were researched before it was concluded that our primary ground control problem was a directional lateral stress Field, with the major stress axis in an east-west direction. The second stop of the procedure was then to test. mining methods and determine if these stresses could be modified to a

Jan 1, 1982

By George S. Kalamaras

Coal strata strength is included as a vague term in most of the pillar design formulas, either as a questionable fraction of the intact coal strength or a size-dependent relationship for scaling down a laboratory value to the in situ strength. In order to introduce a coal mass strength criterion which would be compatible with current design trends, the Rock Mass Rating (RMR) system was revised to incorporate factors governing coal seam behavior under load. A number of adjustment factors have been proposed but, the most significant change, is the introduction of a parameter representing the heterogeneity of the seam. When developing a rock mass strength criterion, it is necessary to find the constants of appropriate intact rock strength criteria and to establish a correlation to scale down these constants as a function of the RMR. For four intact rock strength criteria, the constants for coal were found using the Nelder-Mead method. To correlate the constants of the strength criteria with the coal seam quality values (RMR), a procedure was developed based on finite element modeling of in situ large scale tests for which the RMR was known. A new coal strata strength criterion is proposed, in a principal stress formulation, for modeling coal pillar behavior when the stress field in a pillar is known. A linear relationship is also given, to be used when empirical pillar strength formulas are used to design pillars. The proposed criteria have been evaluated in a case study.

Jan 1, 1993

By David Oyler

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures, the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used.

Jan 1, 1998

By Andrew J. Hyett

The ISRM commission on testing methods has recently presented Suggested Methods for rock stress determination (Kim & Franklin, 1987). This proposes that even if the magnitude of in situ stress is not sufficient to cause significant ground problems, the optimum shape, orientation, and layout of underground structures can be significantly affected by it. In the design of underground excavations, the engineer often requires a knowledge of the average in situ stress tensor in the rock mass. However, attempts to measure a stress state applicable to design have proved frustrating, and a high degree of uncertainty is introduced by the variability in results. In the belief that deduced fluctuations are random in nature, many separate measurements are often made, so that a more reliable stress tensor average, and some indication of the associated variance (see Dyke et al., 1986) can be calculated. Unfortunately, this approach is limited by economic considerations and, as with any sampling procedure, it is imperative to understand the sources of measured variability, in order to design an optimum measurement programme. Cundall(1987) itemised the main causes of stress variability as a. Instrument and measurement errors, and b. Natural fluctuations of stress from point to point, induced by the action of a boundary stress on the internal rock structure. At least four categories exist: i. inhomogeneous rock, bedding, intrusions etc.; ii. differential contraction, creep, or changes in rock properties with time; iii. proximity to faults or discontinuities; iv. cycles of tectonic activity that cause movement on joints. The latter was successfully investigated using the distinct element programme UDEC. In this paper, the contribution of items (iii) and (iv) (i.e. the items related to discontinuities) to the total stress variability will be discussed, for the kind of rock mass shown in Figure 1. Although many authors have concluded that rock joints have an influence on the stress in their vicinity, a more analytical approach is required if the stress distribution associated with different jointed rock masses is to be (i) compared, and (ii) related to routinely measured joint parameters. If this can be achieved then, prior to any attempt to measure stress in a jointed rock mass, a consideration of joint geometry, joint deformability, and the geological kinematics of joints (e.g. the magnitude and direction of previous movements), can place valuable `common sense' constraints on the expected stress system for minimal extra cost.

Jan 1, 1989

By Stephen C. Tadolini

A new innovation in coal mine roof support has been developed by the Bureau of Mines at the Denver Research Center. The technique, called "Thrust Bolting,"1 converts a traditional passive roof support system, a full or partial column rebar bolt, into an active support system by following a specific installation process. The thrust bolting system provides two advantages from a ground control standpoint. First, because the system is active, no roof movement is necessary to put the bolt into tension. This eliminates the possibility of strata separations in sedimentary roots, minimizing progressive-type roof failures. Secondly, the tension placed on the system is independent of mechanical devices or torques. This eliminates the highly variable frictional losses that occur between the bearing plate and the bolt head and in the threaded portions of traditional active support systems. These two improvements create a safer working environment for mining personnel. An additional advantage of this improved support system is the reduced cost of installation and maintenance. The initial support cost is reduced by a minimum of 30 percent per bolt when compared to similar conventional support systems. The labor intensive and potentially hazardous torque¬tension test, required for most tensionable active support systems, is not required for thrust bolts. The potential for improved support performance and cost reduction of thrust bolting has generated a considerable amount of interest from both industry and MSHA. This paper will describe, in detail, the theory and application of thrust bolting and present the results of two underground coal mine case studies.

Jan 1, 1990

By P. Tsang

In order to deal with ground control problems such as roof falls, floor heaves and pillar failures in underground coal mines, a new pillar design method based on the "yield pillar" concept is proposed. Using the finite element model simulation, the functions and mechanisms of the "yield pillar" are studied. The important variables that affect the stability of longwall entry-pillar system are identified. To simplify the geological and mining conditions, a new pillar design method classifies the in-situ roof and floor conditions into four categories: 1) strong roof and strong floor, 2) strong roof and weak floor, 3) weak roof and strong floor, and 4) weak roof and weak floor conditions. The design formulae are derived based on the finite element model simulation, stability study and nonlinear regression analysis. The finite element models used consider the plastic failure properties and time-dependent behaviors of rock. To better organize the finite element model simulation, the orthogonal experiment design is used to arrange the finite element models and proved to be very effective. An application example is used to illustrate the basic design procedures involved in the new pillar design method.

Jan 1, 1993

By Z. C. Song

[THIS PAPER WAS TRANSLATED FROM CHINESE TO ENGLISH BY S. S. PENG, WEST VIRGINIA UNIVERSITY] Immediately after coal extraction, the pressure that causes the movement of the surrounding strata is called mine pressure. Through the strata movement, certain features such as supports taking load arise. This is called "manifestation of mine pressure". The existence of mine pressure is ab¬solute whereas its manifestation is relative and conditional. The visible movement of the surrounding strata occurs only when the applied pressure exceeds the plastic breaking strength. Me support begins to take load only when it offers resistance to the strata movement. The key to investigating mine pressure and its control hinges on understanding the rules and conditions for the manifestation of mine pressure. Since the face moves continuously, the mine pressure and its manifestations are also constantly changing. 'Therefore, it should not only emphasize to obtain its instantaneous magnitude, but more importantly the rules of development changes and their relations to the movement of overlying strata. Once this is resolved, one can estimate the movement of the overlying strata through mani¬festation of mine pressure and predict the time and magnitude of incoming roof weighting. Consequently the location and timing of rib excavation can be correctly selected and thus solve several major problems in the design of mining operation.

Jan 1, 1982

By E. Bane Kroeger

For many years, researchers around the world have been investigating coal pillar stability. Many have focused on trying to optimize the size of the pillars by examining stable and failed pillars in underground coal mines. For mines that are already in operation or companies that are opening a new mine adjacent to an existing mine where the pillar dimensions and stability can easily be determined, this is the preferred technique. However, when a new mine is planned for an area where there has been relatively little mining, then samples of the coal need to be drilled and tested for strength. Because of the fractured nature of coal, this lab testing is often problematic and may often yield poor results because of the limited size and number of samples that can be obtained from the core. To remedy this problem, research was conducted in the labs at SIUC to determine if improvements could be made when optimizing the size of pillars for underground coal mining in Illinois. Through a greater understanding of the relationship between dimensions and strengths of coal samples tested in the lab, it was hoped the in situ strength of coal pillars could be determined with greater accuracy. This could allow the extraction ratio to be increased and more of the coal resources in Illinois recovered without impacting the safety of the mine workers. Many different agencies around the world have published recommended minimum numbers of samples for strength determination based on the size of the coal samples. For two inch cubes, uniaxial testing of at least seven samples is recommended and this minimum number decreases to four when testing four inch cubes. However, the laboratory testing of coal from two seams thus far has suggested this number should be almost doubled to accurately determine the coal strength. Testing also showed there is a pronounced decrease in the variation in the strength of the samples tested as the dimensions of the sample were increased. From the testing results thus far, it is recommended that a sample size versus strength curve be constructed for every coal seam for Illinois. Creating such a curve will better determine both the minimum number of samples and minimum sample dimensions for that seam or region of a particular scam. A second set of tests were conducted in the laboratory to determine the increase in strength with reduction in height for samples with the same width and length. In Illinois, typical pillar dimensions are 40 to 80 feet (12.2 to 24.4 m) wide and long, with coal thickness varying from about 4 to 9 feet (1.22 to 2.74 m). This provides width/height ratios ranging from 4.5 to 17.5. Coal samples having width/height ratios ranging from 0.5 to 13 have been tested thus far. As with most pillar design formulae, the strength of the Murphysboro coal versus width/height ratio was linear and closely matched shape factors published by other researchers. The laboratory testing thus far has identified three factors that affect the strength of laboratory samples, the number of discontinuities, the angles of critical discontinuities, and the shape of the samples. The factor that probably had the most pronounced effect on the strength of the coal samples was the angle of critical discontinuities. This testing has confirmed that there is still a gap that needs to be bridged between the strength obtained from laboratory testing and the in situ coal strength predicted.

Jan 1, 2004

By Thomas L. Vandergrift

With the inevitable expansion of homes, businesses, and infrastructure in coal mining regions, the potential for future subsidence above abandoned mines is of increasing concern. Of particular concern are areas underlain by room-and-pillar coal mines. Unlike areas above longwall mines, where total extraction causes subsidence in a predictable and timely manner, subsidence above room-and-pillar mines is difficult to predict and may be active for many decades. As part of a geotechnical assessment of a water pipeline replacement project, NSA Engineering recently performed an evaluation of tong-terns subsidence potential along the proposed alignment due to time¬dependent failure of underlying room-and-pillar workings. The alignment of the replacement pipeline closely follows an existing concrete pipeline, which lies 150 11 to 300 fl above workings that both pre- and post-date the pipeline. Annual surveys along the existing alignment indicate that some subsidence has occurred, primarily from partial pillaring performed in the early 1980's, but that this subsidence is not active. Using the boundary-clement code LAMODEL as the primary analysis tool, NSA followed a three-step approach to estimate future subsidence impacts on the replacement pipeline. First, historical information for the mine was compiled, allowing for calibration of models to actual field conditions. Then, numerical models of workings directly under and adjacent to the proposed alignment were nun, with model input parameters varied until resulting loading patterns matched historical data, and subsidence in the model approximated that measured along survey lines. Finally, time-dependent deterioration of coal pillars was simulated by decreasing the coal strength in the calibrated model until a realistic "worst-case" condition (stability of barriers, but Yielding of production pillars and pillar remnants) was attained. Subsidence from the previous calibrated model was then subtracted from that of the worst case model to estimate future subsidence and related ground movement parameters that slay occur along the proposed alignment. The replacement pipeline design, incorporating couplings capable of withstanding the ground movements predicted, is now being finalized.

Jan 1, 2000

By Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

Jan 1, 2003

By M. Karmis

Underground mining will disturb the natural equilibrium of the rock mass, causing significant stress redistributions in the vicinity of the excavation with corresponding horizontal and vertical displacements. Subsidence of the ground occurs when these displacements propagate from the mine opening, through the overlying strata, to the surface. Such ground movements may take either of two general forms: a sudden and sometimes violent collapse, or a more gradual and progressive ground movement. The former, characterized by localized failure of roof or pillar in old, shallow room and pillar workings, is rather unpredictable and difficult to analyze. As a result, most control measures are directed toward the latter type of movement, which is associated with the fracture and flow of the strata overlying longwall and high-extraction room and pillar systems, resulting in horizontal and vertical strains in the affected area. Such ground movements can often cause considerable surface disturbances ranging from simple land settlement to severe structural damage. Due to the increasing incidence of this phenomenon in more populated areas and the rising awareness of the problem, it has become necessary to establish a balance between the development of mineral resources and the protection of the environment and society. This paper presents a summary of the major findings derived from a substantial research effort on mining subsidence carried out, during the past few years, in the southern Appalachian coalfield. The research program encompassed the following major tasks: identification of the most significant factor influencing ground movements above mined openings, collection of subsidence case studies for the southern Appalachian coalfield, development of subsidence and strain prediction techniques for that region and initiation of a subsidence monitoring program in southwestern Virginia.

Jan 1, 1984

By M. Karmis

For several centuries surface subsidence has been recognized as an inevitable consequence of most underground mining. In fact, British court records of disputes and litigations related to property damage due to mining subsidence can be traced to the early fifteenth century (Shadbolt, 1978). The first systematic investigations of the mechanisms involved in mining subsidence can be credited to Belgian Mining Engineers. The re- search effort was initiated after the widespread movements and the resulting structural damages suffered by the City of Liege in the 1920's. The publication of Gonot's 1871 treatise "Loie de la NomZ" (normal theory) was one of the most not- able achievements of the Belgian school of that era (Gonot, 1871). During the past 100 years the phenomenon of mining subsidence has been the subject of intensive research, particularly in Europe where long- wall is the most common method of underground coal mining. Many theories have been advanced to explain the mechanism of ground movement as it develops from the excavation, through the superincumbent strata, to the surface. Such theories include the original concepts of beams, arches, domes and the contemporary mathematical modeling principles of strata movement assuming two extreme concepts-- a continuous elastic medium and a stochastic medium for the superincumbent strata. An excellent review of the development of these theories ?-s given by Shadbolt (Shadbolt, 1978). In conjunction with the theories of mass strata movement in the vicinity of mine workings, the subject of surface subsidence predictions has also been the subject of extensive research. The development of reliable and rational techniques of subsidence prediction is imperative, if this phenomenon is to be recognized and controlled within acceptable environmental levels. Empirical as well as mathematical methods have been proposed to fulfill this objective and a comprehensive analysis of these methods has been presented in the literature (Bramer, 1973; Shad- bolt, 1978; Virginia Polytechnic Institute and State University, 1980). As a result of this intensive research effort, it is now accepted in many )coal fields-- mainly in Europe-- that the state of art in subsidence prediction and control has approached a level where mining induced surface displacements can be predicted to a suggested accuracy of less than + 20 percent. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented. In this country, subsidence is rapidly gaining emphasis as an important environmental problem of underground coal mining. Damage resulting from this phenomenon ranges from land settlement to severe structural damage and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). Yet, the art of subsidence prediction and hence control in this country, for both longwall and room-and-pillar coal mining, is far from approaching the maturity reached by the Europeans. In this paper, field measurments and computer modeling techniques have been used to develop some basic relationships of longwall subsidence and its related parameters. Because the objective of this study was to develop regional subsidence trends, all processed information pertains to the Appalachian coal region.

Jan 1, 1981

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

By James Arthur

In deep coal mining the support of the underground roadway is fundamental and without knowledge of the mechanics of ground control a mine is unlikely to be operating safely and efficiently. It is therefore important for the support system to be designed sat¬isfactorily for the size of the excavation required and to do so an understanding of the behaviour of the surrounding strata is re¬quired. Over the last 15 years there has been a major change in the industry and the support systems adopted. The industry has been privatised, legislation has been updated, a comprehensive research programme has been carried out and guidance docu¬ments produced. The paper will show how privatisation has not allowed support standards to deteriorate, highlight research, the legislation and guidance documents updated and how this has led to a reduction in accidents and falls of ground..

Jan 1, 2002