Search Documents

By Shamim A. Dar, Mohd Shuaib, K. F. Khan, Samsuddin Khan

Petromineralogical studies of late Paleocene–middle Eocene phosphate nodules in the Subathu Basin of Solan District, Himachal Pradesh

By Raymond E. Zimmerman

The use of standard dense-media cyclones is well known, as they have been in use for many years. They are especially well suited for operating at low separating densities and for treating difficult coals containing a high percentage of near-gravity at the point of separation. Very few modifications of the basic design have ever been made. The author recently, however, has been interested in the development of a new type of dense-media cyclone that has been produced in Japan. He has observed the testing of this unit and has collected much data which he feels should be of considerable interest to coal preparation engineers. He feels that this unit, called the Swirl Cyclone, may be of substantial value as an alternate to the standard cyclones. It is certainly worthy of further investigation. There has been relatively little written in English-language publications on the Swirl Cyclone. It was briefly described at the Fifth International Coal Preparation Congress. I It has been described in a general manner by the author in two prior publications. 2, 3 This paper proposes to describe this device in more detail and at the same time submit technical data illustrating its wide characteristics.

Jan 1, 1977

By J. L. Hendrix, M. Ahmadiantehrani, G. Ramadorai

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, hypochlorite consumption and concentration, and bed height on total gold extraction. At high pH, hypochlorite stability increases and thus, hypochlorite consumption decreases. At room temperature, total gold extraction is proportional to hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10% and 80% are achieved at 12 and 167 lb/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption, gold extraction increased with decreasing ore bed height. Finally, using calcium hypochlorite results in higher gold extraction than using sodium hypochlorite at a fixed hypochlorite consumption.

Jan 1, 1992

By T. Mudder

The objectives for closure of a hard rock mine include minimizing long term environmental liability, attaining regulatory compliance, and maintaining geotechnical stability, while closing as cost-effectively as possible. Proper planning for closure should come during the feasibility study, design and permitting phases, and during operations as updates. The lack of a proper or updated closure plan can result in severe environmental and economic consequences. Effective mine closure is the result of a combination of innovative concepts, long-term commitments, and multi-party cooperation. The purpose of this paper is to discuss concepts, commitments, and cooperation as they relate to an effective closure plan.

Jan 1, 1999

By Richard C. Corson

The objective of blending materials in a bedding pile is to reduce the variation in successive samples taken from the materials to be blended. In designing a bedding and reclaiming operation, several mechanisms are available to effect the reduction of variability, or increase in homogeneity, of the materials. These mechanisms can act before stacking, in the stacking process, in reclaiming and after reclaiming. In evaluating alternative methods of stacking and reclaiming, the potential user must judge each method on the basis of certain criteria; the capital cost of the equipment, the allowable absolute variability of the reclaimed product and the effectiveness of blending. Several stacking and reclaiming methods have been tested using a computer simulation. Based on the results of this program, factors were developed to describe the effectiveness of blending for chevron stacking of discrete materials and preblended materials, bucket wheel reclaiming and drum reclaiming. From these factors, the total effectiveness of a combined stacking and reclaiming system can be determined.

Jan 1, 1985

By Michael G. Li

Prediction of acid rock drainage (ARD) for low-sulphide, low-neutralisation potential (LSLNP) mine wastes is methodologically different from that for normal sulphidic mining wastes. In this paper. LSLNP wastes are conveniently defined as those with S2 < 1% and ABA-NP2 < 20 kg CaCO3 eq/t. The distinctiveness of ARD prediction for LSLNP materials originates from their frequently low oxidation rates and is mainly attributable to two reasons. First, the utilisation efficiency of available carbonate neutralisation potential (CNP2) rapidly deteriorates when the sulphide oxidation rate per unit mass of waste drops below a certain level. Reducing the flushing rate of a waste has the same effect as increasing the oxidation rate. Second, silicate neutralisation becomes increasingly important as oxidation rates diminish, and can no longer be ignored in LSLNP materials as it often is for normal sulphidic mine wastes. In this paper, the effects of oxidation rate, pore gas CO2 partial pressure, and flushing rate on ARD prediction for LSLNP materials are theoretically demonstrated with the help of modelling using the computer program MINTEQA2. A new methodology for ARD prediction for LSLNP materials is presented in terms of a prediction procedure. Finally, a case study is given to validate some of theoretical aspects discussed and to illustrate the use of the newly proposed ARD prediction procedure.

Jan 1, 2000

By E. Hsieh

Proximity detection in the open pit mine can be used effectively as an operator assist strategy which improves digging production through enforcement of best practices, although it is normally thought of first as a safety tool, and second as a step toward full automation when combined with object avoidance.

Feb 23, 2014

By Joseph C. Rota, Charles E. Ekburg

Introduction The Gold Quarry gold deposit is the largest bulk tonnage epithermal gold deposit in northeastern Nevada to be developed by Newmont Gold Co., formerly known as Carlin Gold Mining Co. Exploration and development of the deposit extended over a period of nearly 50 years before bulk tonnage mining became economically feasible. Proven reserves at Gold Quarry are currently estimated at more than 255 t (8.2 million oz.) of gold, accounting for more than 40% of the total Carlin Trend mineable reserves for 1986. Milling began in late 1985; dump leaching of lower grade ores began in May of 1986. The mill has exceeded the initial design throughput rate of 6.3 kt/d (7000 stpd) and is now processing more than 8 kt/d (9000 stpd). The dump leach facility will process more than 7.3 Mt (8.1 million st) of lower grade ores in 1986. The Gold Quarry ore body is to be developed by an open pit that will eventually be 1830 m (6000 ft) long, 1220 m (4000 ft) wide and 300 m (1000 ft) deep. The mine currently produces 77 kt/d (85,000 stpd) on a 24-hour-a-day, seven-day workweek. Planned pit production will increase to nearly 168 kt/d (185,000 stpd) in 1988. Production equipment currently includes one Demag H-/285, three Komatsu PC-1500 hydraulic shovels, two Cat 992C loaders and 21 90 to 135 t (100 to 150 st) haul trucks. Mining is conducted on 8 m (20 ft) benches within the Paleozoic

Jan 4, 1988

By R. B. Hopler

Explosives R&D has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. This process continues at an accelerated pace today due to the tools presently available to the explosives and mining industries.

Jan 1, 1993

By R. Fred Pena

The Tower Mill has proven to be a grinding machine with a demonstrated application flexibility. Variations in applications have proven to be numerous. This mill was originally intended for fine grinding applications. Subsequent testwork and installations have demonstrated the mill can be utilized in place of ball mills as secondary mills. The following lists a few of the circuits tested: 1. Tower Mill secondary receiving feed from a primary SAG mill grinding stage. 2. Tower Mill as tertiary grind unit following a rod mill/ball mill. 3. Tower Mill as secondary grind unit following a primary ball mill. 4. Tower Mill as a limeslaker. 5. Tower Mill grinding as a primary unit taking limestone crusher discharge. Applications demonstrate the mill is energy efficient and is sensitive to the following consideration: 1. Circuit chosen. 2. Top size of feed. 3. Product size required. 4. Classification equipment performance. 5. Media size required. 6. Media type required.

Jan 1, 1986

By D. T. Maiers, P. L. Wichlacz, P. A. Pryfogle, J. H. Wolfram

The effects of metal solution concentration, biomass density, length of exposure time, and pH were determined for biosorption of molybdenum (Mo) and chromium (Cr) by three organisms. Results indicate that it is possible to sorb Mo and Cr from dilute solutions. Differences were observed in the abilities of an organism to sorb Mo and Cr as well as among respective abilities of the three microorganisms. This suggests an inherent selectivity of the organism which may afford the means to control a sorption-based process. Results also indicate that the metal sorption abilities of these microorganisms depend on duration of exposure, biomass density, solution pH, and the metal concentration of the solution. Each of these parameters suggests an additional means of controlling the sorption process.

Jan 1, 1989

By John W. Rold

These encompass all adverse effects of oil shale mining, processing, and ancillary developments on the environment. Specific problems concern: land, vegetation, wildlife, water, air, population growth, aesthetics and public emotion; and fall into four categories of: land, water, air and emotion. Land includes excavations, spent shale disposal, loss of vegetation and impact on wildlife and domestic grazing, plant sites, buildings and roads, necessary urbanization and the total aesthetic or visual Impact. Water considerations are: requirements for Industrial and domestic supplies, adverse effect of underground water on mining, avoidance of pollution or adverse effect on surface or near-surface water, and the utilization or safe disposal of liquids. Air problems include dust, smoke and stack gas, Public emotional problems include reaction to the above problems, and misconceptions of oil shale country and an oil shale Industry. Government and industry are aware of the problems, and are seeking solutions. Last year, the three affected states studied oil shale environmental problems and solution costs. Colorado estimated environmental costs would add approximately 7% to construction and 7% to operation. The report suggested research in: (1) Water availability and impact; (2) Disturbed lands revegetation and rehabilitation, including spent shale; (3) Environmental inventory and impact; and (4) Regional development and land use planning. Governor Love appointed a 47-person committee representing Industry, government and environmentalists to attack the problems. Research pro-posals were prepared to focus on each problem. $715,000 state, federal and industry money is being committed. Results should provide data for industrial solutions and equitable agency administration.

Jan 1, 1972

By George H. Davis

The Caribou sulfide deposit near Bathurst, New Brunswick (Figure 1) is illustrative of one variety of strata-bound sulfide deposits. It consists of numerous near-vertical sulfide lenses which are concordant to the foliation and lithologic layering of low-grade metamorphic host rocks. Pyrite is the chief mineral in these lenses, but appreciable quantities of sphalerite, chalcopyrite, and galena are also present. Rocks in the Caribou mine area belong to the Tetagouche Group of Ordovician age. They consist chiefly of (1) quartz-sericite and quartz- sericite- feldspar schists, (2) greenschists, and (3) slate and phyllite. The trends of these steeply dipping rocks define the trace of a tight, steeply plunging fold structure, the Caribou fold (Figure 2). This fold plunges approximately 750 to the north-northwest; its axial plane strikes N.20°E. and dips steeply westward. Sulfide lenses of the Caribou deposit are associated spatially with the Caribou fold. The deposit is located in the fold along the contact between quartz-sericite and quartz-sericite-feldspar schists on the hanging wall and quartz-chlorite-sericite phyllites and graphitic schist on the footwall (Figure 3). Genesis of the Caribou deposit is ambiguous because its strata-bound form suggests syngenetic sulfide deposition, whereas its location within a fold suggests structurally controlled epigenetic mineralization. Acceptability of a particular genetic model rests on establishing the time of mineralization relative to deposition, deformation, and metamorphism of the associated rocks. To establish the timing for Caribou mineralization, the deformational histories of rock and sulfide, respectively, were compared. Epigenetic and syngenetic models can be tested against this interpreted structural history of the Caribou deposit.

Jan 1, 1971

By A. S. Ibrado, D. W. Fuerstenau

The adsorption of the cyano complexes of Ag(I). Cu(l), Hg(II), Cd(II), and Zn(II) on activated carbon was investigated as a function of pH and correlated with the speciation diagram for each metal. The results show marked changes in uptake with pH, closely resembling the predominance profiles of their neutral and singly charged cyano complexes. Multicharged negative complexes are repelledby the negatively charged carbon surface. The sensitivity of activated carbon to the charge of the adsorbing species indicates that silver adsorbs as an anion, not chemically bound to the coadsorbing counterions. For the same reason, activated carbon is selective to metals that preferentially form neutral and singly charged cyano complexes, namely gold and silver.

Jan 1, 1990

By M. Li, J. D. Miller

It has been discovered that water insoluble alcoholic solutions of alkyl hydroxamic acids serve as selective collectors for the flotation of phosphate mineral resources (Miller et al., 2000). The effectiveness of the new collector chemistry has been demonstrated by the results from single stage bench scale flotation experiments for feed material from plants in Florida, North Carolina, and Utah. In the best case, from experiments with low grade (5% P20,) coarse feed (16 x 35 mesh), a single stage phosphate recovery of 95% was achieved with a concentrate grade of 31% P20,. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collectors as is evident from a comparison of the respective grade/recovery curves.

Jan 1, 2002

By Karin Bäppler

"When considering large-scale infrastructure projects worldwide special attention has to be paid to the large diameter tunnel construction projects that were successfully completed in the Southern Hemisphere. The projects that are highlighted in this paper are large-scale infrastructure projects in the sector of transport. In focus are four road tunnel projects that were constructed in Australia and New Zealand using mechanized tunnelling technology. The tunnel boring machines (TBMs) that were reliably applied to these four major projects all exceed the bore diameter of 12 meters. These TBMs are therefore in the range of large to very large diameter TBMs. The technology used demonstrates state of the art technology with tailored tunnelling technology adapted to the specific project demands. Two Double Shielded Hard Rock TBMs (Ø 12.35 meters) were used for the construction of the Clem Jones Tunnel in Brisbane crossing beneath the Brisbane River and these two machines have been reused for the excavation of a 4.3km long two-lane highway tunnel for Legacy Way in Brisbane creating a new traffic artery towards the city centre. Two EPB Shields (Ø 12.48 meters) excavated and lined the twin-tube road tunnel for the Brisbane Airport Link. Excavation diameters in excess of 14 meters, such as the Earth Pressure Balance Shield (Ø 14.41 meters) involved in the Waterview Connection Project in New Zealand, are understood in the tunnelling industry as very large diameters. The machine is customized to the requirements and subsurface conditions of Auckland. The paper spotlights the large to very large diameter TBMs that were used and focuses on the comprehensive solutions developed by the machine manufacturer to provide a system with benefits for the contractor especially for the Waterview Project. INTRODUCTION Extensive large-scale road infrastructure projects like the ones implemented in Brisbane (Australia) and currently under construction in Auckland (New Zealand) show the tendency of today’s infrastructure construction projects. Functional infrastructures need to be put in place to cope with the demand of mobility and flexibility of people living in cities and metropolises. Impact during construction work to people or environment has to be kept as low as possible to ensure the quality of life is not disrupted."

Jan 1, 2016

By G. E. Erdman

This paper presents talc milling guided by a theme of "So You Want to Be In The Talc Business". Such a theme strikes a cautionary note to warn the uninitiated of potential pitfalls, and this paper will cover briefly some of the technical traps as well as one of the larger talc milling operations. It is important to our purpose to pre- sent some of the market and mineral complications that make the business of producing and selling industrial talcs much more intricate than an outsider would perceive. Metal markets by comparison are great worldwide pools into which production streams of generally identical metals can flow over a weir of market prices. Industrial talc markets are not as well defined and often must be developed by the producer working closely with a specific customer or groups of customers to prove out the attributes of the specific product from a new property. All the negatives of a new market seem to work against the introductory talc in the forms of industry or customer reluctance to change, sales prices, cost of delivery, mode of transportation, health considerations of the minerals and many more. Just locating the potential customers for a new industrial talc may be a substantial undertaking. Thus, an analogy of the worldwide metal market might compare starting a new talc operation to trying to gather up enough fallen rain drops to be able to start a production stream of a worthwhile size.

Jan 1, 1984

By Donald C. Wotring, Douglas A. Gabriel, Michael G. Vitale

"The Northeast Ohio Regional Sewer District (NEORSD) recently completed the 24-foot diameter Euclid Creek Tunnel using a steel-fiber reinforced concrete segmental lining. During construction HMM, the McNally/Kiewit JV, CSI/Hanson JV, and the NEORSD performed a test program to evaluate replacement of steel fiber with synthetic fiber. A section of synthetic-fiber-reinforced cast-in-situ lining was also placed as part of the permanent works for the starter and tail tunnels. Laboratory and field testing were performed on two complete segmental rings reinforced solely with synthetic fibers. This paper summarizes the testing program, construction, and results of the synthetic-fiber-reinforced CIP lining and concrete segments. INTRODUCTION The principal feature of the Euclid Creek Tunnel (ECT) project is a CSO storage tunnel that is one component of the Northeast Ohio Regional Sewer District’s (NEORSD) Easterly CSO storage and conveyance system. The tunnel, shafts, and appurtenant facilities will be used for the collection and storage of CSOs from the northeastern part of Cleveland, Ohio and subsequent conveyance to the NEORSD’s Easterly Wastewater Treatment Plant for treatment. The ECT project includes five drop shafts that extend as deep as 220 feet below the ground surface. The ECT alignment and shaft locations are shown in Figure 1. Traditionally in northeast Ohio, tunnel excavations were supported with a two-pass system using steel ribs and timber lagging, followed by cast-in-place concrete. Control of rock overbreak proved difficult with large-diameter two-pass operation, and invert degradation led to train derailments. To mitigate these risks, the ECT was supported using one-pass, precast, bolted, gasketed concrete segments reinforced with steel fiber alone. Tunneling operations were very successful and experienced no significant delays or claims. As a result of the positive ECT experience with steel fiber-reinforced segments, Hatch Mott MacDonald, LLC (HMM), McNally/Kiewit (MK) joint venture, CSI/Hanson (CSI/H) joint venture, and the NEORSD performed a test program to evaluate replacement of steel fibers with synthetic fibers in segmental rings. This paper presents the laboratory and field testing program, construction, and results of the synthetic-fiber-reinforced cast-in-place (CIP) lining and concrete segments."

Jan 1, 2016

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

The role of ZnSO4 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electrokinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnSO4 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999