Search Documents

By Alan Rhodes

This study is initiated to investigate the efficiency of separation of mineral slimes using electroflotation as compared to that of column and conventional flotation techniques. Important parameters such as collector concentration, pH, current density, aeration rate, etc., have been studied. The results indicate that electroflotation can be used more efficiently in processing rutile slimes (10 µ) under certain operating conditions.

Jan 1, 1982

By Gregory W. Gustina, Terry P. Boyle

Analysis of the structure of the benthic macroinvertebrate community, consisting of the number of taxa and the relative distribution of total numbers, is a routine method of assessing the ecological quality of streams. Various multivariate statistical techniques, which assess the structural variability of the benthic macroinvertebrate community and the relationship of that variability with natural and anthropogenic environmental variables, have utility in separation of the various physical and chemical factors associated with impact. Multivariate methodology, while computationally complex is statistically rigorous and better integrates physical, chemical, and biological data for more synthetic interpretation. Using the multivariate analysis technique, canonical correspondence analysis, we have analyzed a number of sites in the upper Boulder River Basin, Montana to determine which are the important environmental variables associated with variation in community structure. The results of this analysis an integrated with more traditional analysis of community structure and incorporated in a risk analysis for the mediation of abandoned mines and mill sites within the watershed.

Jan 1, 2000

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By G. Heinrichs

This paper is intended to provide information for one to be able to determine the slurry system head curve for pump applications. The slurry characteristics are the basis for what the size, material of construction, and critical carrying velocity of the pipe will be. The system head curve is adjusted by use of the pipe friction coefficient factor and slurry derate factors. An example using multi-staging of slurry pump curves is presented to compare the wear life relationship of pump parts for a tailing pipeline system head curve.

Jan 1, 1996

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By Andrew J. Neale, Chelvan Veloo

P.T. Freeport Indonesia currently operate a 600,000 t/d mining and 125,000 t/d milling operation in the remote highlands of Irian Jaya, Indonesia. The isolated location and generally difficult working conditions make for challenges not encountered in most North American operations. In spite of this, the mill technical groups have been able to develop and maintain a highly effective level of plant wide automation. This has been achieved through the appropriate selection of available technologies and the implementation of innovative management practices. This paper provides an overview of the control systems currently installed and focuses on those practices which have resulted in the long term success of process control at Freeport.

Jan 1, 1997

Rendering a solid hydrophobic and solid-fluid particle* attachment in flotation are recognized as not necessarily related (1,2). The attachment is governed by forces of attraction and repulsion which need to be considered. The induction time required for attachment after solid and fluid particle are brought into proximity (3-8) illustrates the point. Laskowski(8) showed that a reduced induction time favoured flotation but detected no change in contact angle, a standard indication of solid surface hydrophobicity. Induction .time is observed in fluid-fluid particle coalescence, there being called a rest time (9-11) The induction time phenomenon is related to the presence of a metastable liquid film (disjoining film (2)) of the continuous phase (water in flotation) which must thin and rupture to permit attachment. The lifetime of this film, which is governed by the rate of thinning and the probability of rupture with thicknesss, depends on a complex interaction of forces. Investigating these forces should help clarify the attachment process. Practical benefits would be improved understanding of slimes flotation (12,13) This paper is concerned with the role of the mobile fluid particle-water interface on the film lifetime, in particular, the role of time-dependent or dynamic interfacial properties resulting from deformation of this interface.

Jan 1, 1975

By W. Stark

Many developing countries with little or no previous environmental regulation are now promulgating air quality regulations which require facilities to demonstrate compliance with both process parameter based emission limits and ambient air quality standards. For many companies with operations in developing countries, an air quality compliance program at the facility level is lacking and these companies have very little background information to work with in developing a program for assessing and maintaining compliance. This paper will present a methodology for development of a comprehensive air quality compliance program for operations located in developing countries with new environmental regulations. The experiences of the authors in developing an air quality compliance program for a mining operation located in South America will be used as a basis. A program for meeting new air quality requirements can be developed in seven steps. The seven steps are: (1) regulatory review and project scope; (2) design and implementation of a baseline air quality monitoring program; (3) site visit, (4) development of a complete air emission inventory; (5) dispersion modeling; (6) compliance analysis and compliance plan; and (7) project completion.

Jan 1, 1998

By Ronald J. Roman

As in every business venture, the primary objective of a mining operation is to make money for those who supply the venture capital. Therefore, all decisions concerning the operation of the mining operation should be made in light of the resulting effect on profit. The ultimate control is on profit, but the process is controlled, for example, by aiming for a recovery or concentrate grade knowing its effect on profit. The normal procedure used to determi.ne the profitability of a venture is to "present worth" all costs and incomes back to some arbitrary year zero. Every company has formed a management decision as to what it will require as a minimum return before it will undertake an investment. Once the economic analysis is completed, investment will be made only if the venture shows a positive present worth. If two alternatives are available, the alternative with the larger positive present worth is the one chosen. The same principles can be applied to the selection of a production schedule.

Jan 1, 1971

By Kendall Y. Keuhey

The Mercur Mine, developed and operated by Getty Mining Company, is designed to process 3,000 tons/day of gold ore from the historical Mercur Hill mining district. The mill process involves crushing, grinding, and cyanide carbon in leach for recovery of gold ores ranging from 0.08 to 0.10 oz/ton. During the mining of normal grade ore, a substantial tonnage of material containing 0.02 to 0.05 oz/ton is mined and would be available for heap leaching. Also, Getty Mining is developing methods to test and prepare lower grade material for heap leaching by rejecting a course rock fraction from the grinding circuit SAG mill. This lower grade fraction is suitable for heap leaching, and its removal will upgrade the regular mill feed. Other test methods are directed toward leaching techniques on some 4.0 million tons of tailings that resulted from roasting and/or cyanide leaching Mercur ores in the early 1900s. The natural carbons associated with the Mercur deposits require special treatment to reduce their gold adsorption effects when leached with cyanide.

Jan 1, 1983

By L. Rudolphy, P. Tähkiö

"The cPlant is a modular flotation plant which has been designed to minimize capital expenditure and risk. The plant is based on a number of standard modules, for both flotation and ancillary equipment, which can be configured to give the required flowsheet for the ore being treated. All of these modules can be rapidly deployed and erected onsite, minimizing not only engineering time and site preparation but reducing the time taken to get the plant up and generating revenue. Given the paradigm shift in flotation circuit design that has been employed in the cPlant it may allow smaller, previously uneconomic deposits to be exploited and create a more cost efficient upgrade route for existing plants. This paper introduces the cPlant and presents a case study comparing EPC cost and development timing of a cPlant against a traditional flotation circuit design. INTRODUCTION In the development of any mining project the cost associated with process plant engineering, equipment procurement and installation can affect the financial viability of a project. This is of special significance for smaller scale mining projects which perhaps don’t have the mine-life or revenue generation to justify the payback on a modern processing facility. Listening to customer feedback and understanding the challenges that small to mid-sized projects can face lead Outotec to the development of the cPlant. Modularization of mineral processing plants isn’t a new idea with a number of examples being reported in literature for gravity gold (Cabot, Trudel and Cabot, 2001; Gray et al., 2006), dense medium separation (September and Abate, 2006) and even hydrometallurgy (Saario et al., 2013). All these plants have been developed to try to improve on the traditional economics associated with fixed processing plants. Using standardized modules to construct a plant reduces engineering time and design costs which can both be beneficial to the outcome of a project. In addition the modular nature of the plant lends itself to transport to remote sites and rapid installation with only minimal site preparation required. A plant of modular design also has several other advantages over its conventional cousins. Firstly it is relatively easy to expand by duplicating existing modules. Secondly the modules can be treated as building blocks for the process and rearranged if a change in conditions requires flowsheet adjustment. Thirdly, there is potential to disassemble and remove the modular units at the end of the mine life. The ability to easily disassemble, re-pack and transport the plant to a new location not only is important to the long term environmental footprint of an operation but can also be seen as a bonus to an operator that has a number of small ore deposits. If applied in this way modular plants have the potential to create a whole new operating model for previously unviable ore deposits."

Jan 1, 2016

By Richard L. Bullock

OPEN STOPING An open stope is an underground cavity from which the initial ore has been mined. Caving of the opening is prevented (at least temporarily) by support from the unmined ore or waste left in the stope, in the form of pillars, and the stope walls (also called ribs or abutments). In addition to this primary support system of open stoping, some secondary support may also be required using rockbolts, reinforcing rods, split pipes, or shotcrete to stabilize the rock surface immediately adjacent to the opening. The secondary reinforcement procedure does not preclude the method classified as open stoping. There are many forms of open-stope mining used to extract the initial material from a mine. Having once established that the mineral and waste rock are competent enough to use an open-stoping method, and assuming that the reserve is not classified as gassy, the Form which the method will take is primarily determined by the dip and thickness of the reserve. How these two factors affect the selection of the open-stope mining is discussed in a later chapter. At this point it will suffice to say that the classification of the open-stopes mining system which follows is based on whether dry' broken materials flows by gravity or whether it must be moved by nongravity methods where energy must be supplied to move the material. Room-and Pillar-Mining Room-and-pillar mining is an open-stoping method where mining progresses in a nearly horizontal or low angle direction by opening multiple stopes or rooms, leaving solid material to act as pillars to support the vertical load. Since the direction of excavation (angle of dip) is below that which would cause the dry material to flow by gravity to a drawpoint or gathering point, the material must be loaded in the room where it was extracted and transported to a point where it will flow, either by gravity or mechanical means, to a central gathering point to be taken out of the mine. This is an important aspect of room-and-pillar mining which differentiates the system from other open-stope mining methods which rely heavily upon gravity to transport ore from where it was broken to a lower elevation, usually through a drawpoint. There are many variations of the method which go by a number of names in local districts: breast stoping, breast-and-bench stoping, board-and-pillar, stall-and-pillar, and panel-and-pillar are all basically open-stope room-and-pillar mining. In some instances detailed stope planning is almost nonexistent; i.e., the operator simply follows the visual pay values, leaves pillars only where necessary, and tries to locate them in the zones of lower value. This method of mining is as old as the beginning of underground mining itself, dating back thousands of years. Early in the history of mining in this country, the term "gophering" was used to describe this method (Peek 1941). The term is appropriate, for it brings to mind the exact results of this type of system-a random and irregular room-and-pillar mine. In other instances where the mineral values are consistent both in physical dimensions and quality, the mine layout can be planned to the last detail, resulting in a uniform room-and-pillar mine. Coal, trona, gilsonite, potash, oil shale, salt, limestone, and sandstone mines can usually follow such a system. Today, most metal mines using a room-and-pillar operation try to mine as regular a pattern as possible but deviation in height, width, thickness, dip, and grade of the ore results in comparable deviation in the mine plan. Variations of the Room-and-pillar System It is necessary to briefly describe some of the many variations of the room-and-pillar system of mining, enabling the reader to fully explore the concepts and become familiar with the terminology used before going on to the details of mine design. Full-Face Slicing: If in the process of opening the rooms the total vertical extent of the mineral values of the particular seam or strata are extracted from the advance of one vertical face, the term used to describe this is full-face slicing. This face is also known as the "breast." There is no mineral of economic value intentionally left either in the floor or the roof (back) to be mined later. To be able to extract the full-face height in one pass, the mining equipment must obviously be designed to reach as high as the back. In an Appalachian coal mine, this may be all of 660.4 mm (26 in.); for a future oil shale property it might be 15.24 m (50 ft). Normally, however, in a majority of mines where the mining face gets over 6.09 to 6.7 m (20 to 22 ft), the tendency is to divide the face into more than one pass. Over this height, it becomes difficult to properly see and remove loose rock from the back with a hand "mining bar." Where the process of taking down loose rock has become mechanized, higher full-face mining can be safely practiced. Most eastern and midwestern coal seams and western uranium, trona, and potash seams in the United States are easily reached in a single face; many limestone, lead, and zinc mines must resort, at least in part, to "multiple-slicing" to remove all the minerals of value. Multiple Slicing (also known as multiple-pass mining): In many cases it is not practical to carry the full vertical height of the mining horizon as a full face. The face is divided into parts known as the breast, bench, and/or brow. Ideally, if the operator knows the vertical extent of the mineralized zone, he will drill and blast the first pass at the top of the zone, thereby

Jan 1, 1982

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By Y. Numata

2-Mercaptobenzothiazole (MBT) is a heterocyclic-mercaptan and belongs to a group of molecules containing nitrogen and sulfur as electron donor atoms. MBT has been employed as a collector in flotation under names of MBT, Captax, and Flotagen. It is a major constituent of reagents in the 400 series of the American Cyanamid Co. Current applications of the reagent include flotation of copper minerals, tarnished or oxidized lead, copper activated sphalerite, and nickel ores. It has been used successfully in the flotation of pyrite in acid circuits in the range of 4 to 5.

Jan 1, 1990

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbonate gangue from sedimentary apatites (francolite) in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to benepciate a high- MgO siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for car- bonate removal and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the MgO was rejected in the froth. The phosphate flotation stage produced concentrates analyzing about 31% P2O5 0.7% ? 5 MgO, and 4% insol. The overall P2O5 recovery In the two stages was about 85%

Jan 1, 1991

By B. J. Arnold, F. F. Aplan, S. Chander

There is a broad range of chemical reagents of potential use to the coal preparation industry: flotation frothers, flotation collectors (for coal, ash minerals or pyrite) and collector-assisting (conditioning) agents, flotation depressants (for coal, ash minerals or pyrite), pH regulating agents, acid mine drainage treatment chemicals, flocculants, filtration aids, dispersants, dust suppressants (wetting agents and car-top or pile binders), freeze conditioning agents, water treatment chemicals (corrosion and scale inhibitors) and suspension stabilizing reagents (dispersants, stabilizers, biocides). The application of each of these types is discussed with particular attention paid to those of greatest importance: flotation frothers and collectors, pH regulators and acid mine drainage treatment chemicals, flocculants and freeze conditioning agents.

Jan 1, 1986

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992

By John P. Weir

The planning of an underground mine for successful extraction of a bedded deposit in sedimentary rocks requires the integrated evaluation of many interdependent problems. The development and coordination of feasible solutions are the responsibility of the mining engineer. One of these problems will be discussed herein; this is the design and .layout of mine workings to secure effective control of the strata above and below the deposit. The objective is the simplest possible repetitive system permitting safe maximum recovery at optimum cost. Mining conditions to be encountered must be predictable. The best mining equipment is ineffective unless strata are controlled. Conversely, a mining layout is only of academic interest, if equipment can not be adapted to work it with adequate provision for ventilation, compliance with mining laws, proper ingress and egress and other practical requirements. Strata control, then, is but one of the mining engineer's problems, and the solutions must be worked out concurrently with solutions to other problems. Dr. Karl F. Fetters in his introductory remarks before the Fourth International Conference on Strata Control and Rock Mechanics at Columbia University said that mining engineering ?has come from the stage of empiricism backed by intuitive reasoning, to where it is based on fundamental scientific and engineering principles?. The standard curriculum in mining engineering now reflects such a change. In common with other branches of engineering education, less and less emphasis is placed on practical skills and more and more on broad scientific education. Science, research and the quest for basic truth are stressed, while descriptive courses and the teaching of specific skills are limited.

Jan 1, 1966

By J. L. Osiensky, R. E. Williams, J. Linehan

The hydrostratigraphy of uranium in situ leach sites consists typically of interbedded layers of sand, silt, clay and gravel deposited by fluvial processes. 'These layers usually form leaky multiple aquifer systems where sand and gravel aquifers are separated by silt or clay confining layers (aquitards). It is very important to evaluate the hydraulic properties of the ore zone aquifer and the confining layers by aquifer pump testing to ascertain the effects that in situ leach mining will have on the multiple aquifer system. The degree to which current methods of aquifer pump testing will provide the information necessary to adequately characterize the hydraulic properties of the ore zone aquifer and its confining layers is dependent upon the hydrostratigraphic conditions at the site and the limitations of the testing methods. The primary objectives of the aquifer testing program should be to evaluate the vertical hydraulic conductivity of the confining layers and to quantify leakage into or out of the ore zone under mining conditions.

Jan 1, 1984

By Lyda W. Hersloff

As decommissioning of various radioactively contaminated facilities begins, the question of appropriate residual surface contamination becomes an issue. Surface contamination can result in exposure to people via inhalation, ingestion, and external radiation exposure, There is therefore the potential of exposure to workers involved in the dismantling of a facility as well as members of the general public acquiring salvageable equipment, tools, and building materials. The levels established as acceptable for unrestricted use by national and international organizations vary by as much as an order of magnitude for certain radioactive materials. The calculated doses associated with some acceptable contamination levels can be significant. The principle of ALARA, as low as reasonably achievable, is therefore a necessary element in establishing surface contamination levels for a specific site. Some components in evaluating site specific surface contamination levels for unrestricted use, especially removable contamination, include evaluations of the historical use of a facility, the mixtures of radioactive materials a&sociated with surface contamination, and resuspension factors for various materials.

Jan 1, 1991