Search Documents

By ANA E. BOHE, MICCO GEORGINA DE, GASTON G. FOUGA, JUAN P. GAVIRIA, FEDERICO J. POMIRO

To the best of our knowledge, this paper comprehensively summarizes a thorough study to determine the thermodynamic viability of the reactions between light rare earth oxides and chlorine with and without carbon. The kinetics and mechanisms of light rare earth oxide chlorination and carbochlorination reactions are analyzed and discussed according to results in the literature. Lanthanides between lanthanum (La) and gadolinium (Gd) are considered as light rare earth elements (LREEs) in agreement with previous literature and the results detailed in this review. Both laboratory- and industrial-scale light rare earth chlorinations and carbochlorinations, starting from oxides and ores, are reviewed.

By D. Bahrami, G. Danko, W. Asante

"It is prudent to interpret atmospheric monitoring signals in real-time for checking the safe limits of the air conditions in underground mines. In gassy mines, such real-time evaluation increases the safety of operation. In all mines, the continuous monitoring and evaluation contribute to maintaining air conditions to be within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase of hazardous contaminant concentrations can be predicted by signal pattern recognition, root-cause analysis of rapid changes toward deterioration and forward prediction in time using algorithms and numerical models. This paper focuses on analyzing signal patterns to recognize dangerous trends as well as forward predicting the various environmental and working conditions that may affect safety in underground mines. Efficient numerical ventilation model with heat and gas contaminant simulation components is needed for the analysis of real-time atmospheric monitoring data. Computational speed enhancement methods are discussed and tested in numerical examples, using the Jacobian sensitivity matrices for signal propagation prediction. INTRODUCTION The focus area of this paper is mine safety, related to hazardous atmospheric conditions in a mine ventilation system. Improvements by recognizing safety hazards caused by heat of combustible gases or the accumulation of poisonous gases in a mine are addressed. The recognition of safety hazard by manual evaluation is difficult because of the complex nature of information and the large amount of monitored data from measurement by atmospheric sensors such as air velocity, pressure, hazardous gas contaminants and temperature. In order to recognize problem-causing trends, it is necessary to evaluate continuously individual measurement data from the Atmospheric Monitoring System (AMS) of the mine during their time-dependent variations. In addition, the combined effects of various signal trends need to be simultaneously interpreted in their cross-effects. It is very difficult to foresee the possible outcomes of intertwined signatures of various problems by continuous human observation. For example, a steady, continuous methane concentration measurement together with a sharp drop in barometric pressure from the AMS sensors may be a case for worry in future time due to pressure-induced methane increase from the coal seam or the gob (Danko et al., 2013). This future increase can be predicted by a time-dependent Ventilation Air Model (VAM) and its surrogate Air Parameter Predictor Solver (APPS) model. A calibrated VAM or APPS model can indeed predict a likely methane concentration variation in future time as a function of previous and new air pressure as well as air velocity (Danko, et. al., 2013). Such a future trend, however, cannot be seen from the raw measurement data."

Jan 1, 2017

By E. Watkins, V. Gangrade, P. Zhang, J. Addis, D. W. H. Su, T. Minoski, C. Hollerich, M. Van Dyke, S. Schatzel, H. Dougherty

"This paper presents the results of a comprehensive study conducted by the Centers for Disease Control (CDC), National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) to evaluate the effects of longwall-induced subsurface deformations and permeability changes on shale gas well integrity and safety under shallow cover. NIOSH researchers selected a study site over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under 482 feet of cover. One in-place inclinometer well and three permeability monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the inclinometer well and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the first 1,500-ft-wide longwall panel on the south side of the abutment pillar mined by the site.A number of FLAC3D finite difference simulations (Itasca Consulting, 2017) were conducted to estimate surface subsidence, coal pillar pressure increases, and horizontal displacements in the in-place inclinometer (IPI) monitoring well. Comparisons of the FLAC3D finite difference simulation results and the surface, subsurface, and underground instrumentation results show that the measured IPI casing deformations are in reasonable agreement with those predicted by the FLAC3D models, and that the measured surface subsidence and underground pillar pressure are in excellent agreement with those predicted by the 3D models. Measured permeability changes were incorporated into a preliminary calculation to evaluate the effect of a hypothetical shale gas well leak on longwall ventilation. Results from this 2018 research clearly indicate that under shallow cover, the measured horizontal displacements within the abutment pillar are at least one order of magnitude higher than those measured in a 2017 study under deep cover and slightly higher than those measured in a 2014 study under medium cover. This research represents a very important step and initiative in utilizing the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the workers in the oil and gas industries"

Jan 1, 2019

By Dean H. Herrick

The production of crushed stone in the United States has exceeded 1.0 Gtpy since 1987. Eighty percent of the crushed stone produced is used in the aggregate industry, accounting for over half of the quantity of natural aggregate consumed in the United States. Approximately 718 of the crushed stone produced in 1989 was limestone and dolomite followed by granite, traprock, sandstone and quartzite, miscellaneous stone, marble, shell, calcareous marl, volcanic cinder and scoria, and slate in order of descending volume (Table 1). Of the remaining 20% crushed stone produced in the United States and not used as aggregate, 12% is used in the manufacture of cement which is an important construction material. Only 8% of crushed stone is used in specialty products not associated with the construction industry. Therefore, this chapter will concentrate on crushed stone as used in aggregates, with occasional reference to other uses or to chapters which discuss specific nonconstruction uses of crushed stone. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass by the addition of cementing or binding materials that produce a concrete by compaction, or by natural weight to produce a road or foundation fill. Aggregates are usually from 80 to 100% of the material volume of the construction masses in which they are used. Conditions necessary for a rock deposit to be developed for construction crushed stone include: Quality-should pass rigid specifications for strength and durability; Quantity-adequate volume of rock is needed to have a production life of at least 10 years, preferably 20 or more years; Market-must have adequate market to support a new crushed stone operation; Transportation-transportation cost must be competitive for the intended market; Environmental-the impacts of mining, processing and transportation of crushed stone on the environment at or surrounding the mine site must be within acceptable limits; Permitability-mining, processing and transportation of crushed stone must usually be permitted by governing agency. The following discussion will touch upon all facets of crushed stone operations from the mineral deposit and its geology to technology, uses, economic factors and end with governmental regulations of mining crushed stone. The sections are not designed to answer all questions, but rather to be an introduction to the crushed stone industry. Where more information is required, The Aggregate Handbook by Barksdale (1991) is recommended as the best general source.

Jan 1, 1994

By Arthur F. Eidson

INTRODUCTION If a uranium mill worker is involved in an accident, analysis of excreta for uranium content and[in vivo] counting methods are used to estimate the extent of the possible exposure and to predict the pattern of uranium distribution among tissues (Spitz, [et al]., 1980). Interpretations of urinary excretion data are based on studies of human exposures to single uranium compounds including U02, U308, U03, UF4, U02F2 and UF6 (Alexander, 1974). Refined uranium ore (yellowcake) is a variable mixture of U03-NH3-H20 adducts (ammonium diuranate, ADU) and their thermal conversion product, U308. The variability in composition of yellowcake (Kalkwarf, 1979; Eidson and Mewhinney, 1980; Dennis, Blauer and Kent, 1981) complicates the interpretation of bioassay data from individuals that might have inhaled any single yellowcake material. A test system would be useful to estimate the dissolution behavior of a particular yellowcake aerosol inhaled by a worker and aid in the interpretation of bioassay data collected before and after an accident. A series of experiments was conducted for this purpose. The objectives of these studies were to: 1) develop specific criteria for comparing [in vitro] dissolution systems and 2) use the criteria to evaluate solvents, methods and experimental temperature and pH conditions used in previous studies. Dissolution experiments were conducted using different combinations of solvents, conditions and methods with a common yellowcake sample. Because little information is available from human yellowcake inhalation exposures to evaluate the [in vitro] results, criteria for evaluation of different tests were derived from a model of yellowcake dissolution in lung constructed from a number of cases in which humans were exposed to single uranium compounds known to be in yellowcake (Mercer, 1975). MATERIALS AND METHODS Materials The powder used in the tests was taken from one lot of yellowcake obtained from a commercial uranium mill. The same powder was previously designated as Mill D in Eidson and Mewhinney, 1980 and Mill 2 in Kalkwarf, 1979. The ammonium diuranate content was measured by infrared absorption to be 25% ± 1% (Eidson and Mewhinney, 1980). Solvents The compositions of the two biological fluid simulants used are compared in Table 1. Simulated lung fluid (SLF) (Kalkwarf, 1979; Dennis, Blauer and Kent, 1981) was chosen to simulate the composition [ ] of lung fluid as closely as practical (Moss, 1979). Simulated blood serum ultrafiltrate (SUF) (Eidson and Mewhinney, 1980) was chosen because of previous successful efforts to model human urinary excretion of inhaled plutonium aerosols (Kanapilly Raabe and Boyd, 1974) and the dissolution rate of 241Am02 in Beagle dogs (Mewhinney and Griffith, 1981). Major differences are that simulated lung fluid contains Mg2+ and a higher Ca2+ concentration than SUF and that SUF contains ammonium ion. Both solvents include protein substitutes; acetate is used in SLF, while amino acids are used in SUF. Both solvents include phosphate but the chelating agent diethylenetriaminepentaacetic acid (DTPA) is included in SUF to prevent possible formation of insoluble uranyl phosphate precipitates that would result in an underestimation of solubility. In addition to the above solvents, modified solvent compositions were prepared to investigate the role of specific salts in yellowcake dissolution studies. Solutions of SUF (Table 1) were prepared without DTPA (SUF-DTPA) and without amino acids (SUF-amino acids). No solution excluded both DTPA and amino acids. The SLF solutions were prepared with DTPA (SLF + DTPA) and without phosphate

Jan 1, 1981

By Garry W. Warren

The electrochemical oxidation of chalcopyrite in the absence of-a chemical oxidant was studied in ammonia/ammonium sulfate solutions by anodically polarizing electrodes prepared from massive chalcopyrite. The effects of pH, cupric and ammonia ion concentration were systematically evaluated. Kinetic parameters were obtained from the anodic charge-transfer regions of the anodic polarization curves. Increasing ammonia and hydroxyl ion concentrations increased the rate of oxidation. A mechanism is proposed which explains the first order dependence of (NH3) and (OR) associated with a single electron transfer process. An empirical relationship which accurately describes the dependence of the rest potential (i.e. zero current potential) on solution composition is also given.

Jan 1, 1978

By T. McCallum, C. Cooper, C. Lewis

"Following a successful solvent extraction (SX) pilot plant demonstration in 2016, CYANEX® 600 has been used commercially to recover molybdenum from concentrate leach liquor since March 2017. Consistent with the piloting results, the commercial plant has achieved expected molybdenum recovery, a significant reduction in base consumption, and a step-change improvement in physical performance. This paper highlights the optimization activities and plant performance from startup through normal operation. INTRODUCTION Historically, tertiary amines have been the most commonly used extractant for molybdenum and rhenium recovery. Tertiary amines utilize a protonation of the ligand combined with an anion exchange mechanism as proposed in equations (1-2). R3N + H+ ???R3NH + (1) 4R3NH+ + Mo8O264- ???(R3NH+)4Mo8O264- (2) In addition to the transfer of Mo and Re, the amine transfers acid and other anions to the strip liquor. The undesirable transfer of other species increases base consumption during stripping, impacting operating costs. Additionally, lower solubility of molybdenum-amine complexes create operational challenges, resulting in diminished physical performance. The presence of colloidal Si in concentrate leach liquors and the formation of Pickering Emulsions adds to the physical plant performance challenges with the amine extractant. CYANEX® 600, a phosphinic acid-based extractant, uses a cation exchange mechanism proposed by equation (3). 2(H2R2) + MoO22+ ??(HR2)2MoO2 + 2H+ (3) The cationic exchange mechanism eliminates chemical transfer of acid and other anionic impurities and avoids some of the physical challenges of the amine extractant (emulsion and 3rd phase formation). In addition, the reagent offers high selectivity for Mo over Re, which may be desirable in certain moly pressure oxidation (POX) flowsheets. Alkali base (ammonium hydroxide, sodium hydroxide, sodium carbonate, etc.) is used for molybdenum stripping. Therefore, reduction or elimination of chemical acid transfer from extract can significantly reduce base consumption in strip. Extensive laboratory and pilot plant testing was completed to evaluate the use of CYANEX® 600 for molybdenum recovery at Freeport-McMoRan’s Bagdad operation. The test work and pilot demonstration confirmed a reduction in base consumption along with improved selectivity. In addition, the evaluation highlighted a step-change improvement in physical performance over the incumbent amine extractant. The decision was made to convert the commercial operation to CYANEX® 600 in March 2017."

Jan 1, 2018

By R. Worrall

The global mining industry has been proactive over the last decade in finding ways to embrace the concept of sustainability. However, legacy mine sites (which include abandoned derelict and orphan mine sites) across the world continue to present issues for the global mining community, governments, local communities and NGOs. Unfortunately there has been much less academic focus on this area of mining and sustainability. This paper seeks to address how principles of sustainable development can be used to guide the development of processes for addressing post mining landuse issues for legacy mining areas. This is being done using a case study area located near Ipswich, in southeast Queensland, Australia. This area has a 160 year history of coal mining, and was one of Queensland?s crucial early industries. Mining in the area ceased in 2003 leaving a degraded landscape covering an area in excess of two thousand hectares adjacent to one of the fastest growing urban areas in Australia. A sustainability criteria and indicators framework for post-mining landuse on legacy mined land, developed from current best practice used for measuring sustainability across a range of industries is being developed. A review of current best practice suggests the framework should: (1) consider in equal measure environmental, social and economic factors; (2) have a minimum number of indicators which should be easy to identify and measure; (3) must have indicators with a meaningful output; and overall, the framework must consider particular requirements of the site being investigated. Application of the framework to the case study area is an ongoing aspect of this research, and the results will be evaluated through the use of expert stakeholders.

Jan 1, 2007

By M. C. Mound, L. Fradette, C. Colbert

Metallurgical Accounting in the mineral processing industry transforms accumulated process data, including flow rates and assays, into a coherent information format. This is used to rapidly provide production reporting and key performance indications. A fully comprehensive and coherency of available data must be a component of any system expected to accomplish reconciliation in the mass balancing process. Quality issues are thus improved with such desired methods via a mass-balancing engine utilizing the results of measurements acquired by various on-line sensors, analyzers, and sophisticated laboratory equipment. Metallurgical Accounting, when accomplished through such an engine, provides high value information in a simple, straightforward, and simplified manner. Exceptional utility is then transparently available to authorized personnel for access to metallurgical accounting reports, production reports, mass balance results, performance indicators, and so on. This paper discusses how such information can be used to "drilldown" into each result set by consulting the data hierarchy to evaluate and validate calculations and input data used to produce the specific results being queried. The power of such a system resides in the full and true integration of all production and laboratory data. What is integrated are the data thus acquired via a single user interface, a single database, a single configuration tool, etc. From this comes the derivation of contextual information and its maintenance. It is possible to reduce metallurgical accounting and production reporting from possibly hours or even days to a matter of minutes. The result is maximization of information reliability and availability from masses of otherwise discrete and difficult to access key data.

Jan 1, 2003

By J. Seiter

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a Polycrystalline Diamond Cutter (PDC) drill bit generates less respirable dust and hazardous noise than a competing Tungsten Carbide (WC) bit, in dry vacuum drilling. In order to control the drill parameters the drilling tests have been conducted in a laboratory setting. The results were met by determining the quantities of dust and noise generated using each drill bit and analyzing those levels by using monitoring devices and software to collect the data. This paper includes information on experiment setup, equipment used, drilling parameters, and data collected. The test results suggest that there are noticeable trends that the PDC bits produce less dust than WC bits but more testing is needed to substantiate these trends.

Feb 23, 2014

By K. Hanumantha Rao, K. S. E. Forssberg, A. Vidyadhar

Using pure albite and quartz minerals, the separation of albite from quartz using mixed cationic/anionic reagent schemes is assessed through Hallimond flotation, zeta potential and diffuse reflectance FTIR studies. The reagent schemes are tested in bench-scale flotation for the separation of albite from Greek Stefania feldspar ore. The single mineral flotation tests showed the feasibility of selective albite flotation from quartz at around pH 2 using a mixture of cationic diamine and anionic sulfonate collectors or a combined cationic-anionic collector of diamine-dioleate. In contrast to the selective flotation response of albite at pH 2, where albite is slightly negatively charged and quartz possess zero charge, the zeta potential and FTIR studies elucidate similar adsorption behavior of mixed collectors on both of the minerals. The infrared spectra not only showed the co-adsorption of anionic sulfonate or oleate with diamine on the surface but also showed that the diamine adsorption increases with the presence of anionic collector. The intrusion of anionic collector in between adjacent surface alkyl ammonium ions decreases electrostatic head-head repulsion, thereby increasing the diamine adsorption by increasing the hydrophobic tail-tail bonds. The discrepancy in the flotation and adsorption results at pH 2 is attributed to the coarse and fine size particles employed in these studies, respectively. The comparable adsorption on fine particles of albite and quartz at pH 2 is explained by the interaction of ammonium ions on silanol groups by hydrogen bonding besides electrostatic interactions. The bench-scale flotation results indeed showed that selective albite flotation takes place only after desliming the feed material. An albite concentrate exceeding 10% (by weight) Na20 is produced from a material containing about 6.5% (by weight) Na20, where an albite product of more than 9% (by weight) Na20 is considered to be valuable. Key words: Flotation, Adsorption, Zeta-potential, FTIR

Jan 1, 2003

By C. L. Schneider

The calculation of the liberation spectrum in the product from continuous milling operations is a problem of considerable importance and is difficult to solve because the population balance equation must be integrated in two-dimensional space. Complete solutions require the estimation of a large number of parameters unless a structural model of the ore texture can be used. A very simplified textural model based on the use of the modified Andrews-Mika diagram and the PARGEN simulation of multi-phase particles has been formulated and is used to simulate the behavior of a continuously operating laboratory ball mill. A sensitivity analysis for this mill has been done to show the likely effect of model approximations on the predicted liberation spectrum which will be measured.

Jan 1, 1992

By Russell G. Shomperlen

Grinding mills in excess of 5 meter diameter and 3500 kilowatts per mesh are putting new demands on big gears. This paper returns to the basics of ring gear design beginning with the fundamental power formulas specified by AGMA. Specific emphasis is given to those elements in the rating equations which require closer attention as gear diameters and transmitted power increase. Strict process control in the manufacture of the gear blank is also stressed. Finally, the writer offers a guide to proper installation, lubrication and maintenance.

Jan 1, 1981

By K. F. Unrug

The method of coal pillar design involves primarily two aspects, the geometry of the pillar and the strength of the coal. However, the strength of the coal has to be emphasized with respect to the entire pillar dimension rather than isolated strength values of coal samples taken and measured from different locations. The presently applied pillar design systems do not specify clearly what the coal sample strength really represents. The intention of this paper is to introduce the concept of seam strength as opposed to the current practice of using coal strength as a prime design criteria in the formulation of pillar calculations. Seams are most of ten composed of multiple layers of coal, partings, and bone in different configurations, changing within the vertical section of the seam even in relatively close locations. The difference in strength between the weakest and strongest component of the coal seam could be as much as five times or more. An experimental approach based on multiple compressive tests performed on coal samples from the Coalburg and the Warfield seams from Eastern Kentucky was undertaken. The analysis of the results lead to the conclusion that for pillar calculations both the weighted mean of the seam strength and the strength of the weakest stratum should be considered rather than the relatively vague aspect of coal strength The design of pillar dimensions based on the above mentioned aspects should assure a more realistic design performance.

Jan 1, 1985

By T. Stuczynski

In the past ten years about 3000 wastewater treatment plants have been built in Poland. The result of this development has been a massive increase in overall sludge production. According to data supplied by the Ministry of Environmental Protection, 400,000 dry tons of sludge are generated every year in Poland (Koblak-Kalinska 1996). Still it is difficult to estimate the amount of sludge, which is used in agriculture or for reclamation purposes. However, it can be assumed that this comes to no more than 10 percent of all sludge produced in Poland on a yearly basis. Thus it became obvious that an urgent solution to this problem was needed. Local authorities in Silesia realized in the early 90?s that a demonstration was necessary to encourage the proper utilization of sludge. This was the basis for establishing the Biosolids Subpart of the Silesia Project, which addressed the use of biosolids in the reclamation of mining and smelting dumps (Stuczynski et al. 1996). Metal waste sites themselves are known to contain more than 87 million tons of waste (Pistelok et al. 1995). Each year this amount increases by approximately 400,000 tons. We realized that a simple solution for stabilizing these sites would be to cover them with vegetation in order to reduce leaching of toxic elements, as well as to keep metallic fugitive dust from entering the environment. The reclamation of smelter waste sites, which was carried out within the framework of the Silesia Project was a joint effort of local government, industry and international research institutions/agencies, including the US Environmental Protection Agency (EPA), the Center for Research and Control of the Environment (OBIKS), Virginia Polytechnic Institute and IUNG. One of the goals was to evaluate the possibility of adapting the rules of sludge management currently used in the United States to conditions commonly found here in industrial regions of Poland. However, the main objective of the Silesia Project was the development of guidelines concerning all aspects of sludge use for the reclamation of degraded lands and waste sites. Biological aspects related to reclamation of metal waste with the use of biosolids will be discussed in this paper.

Jan 1, 2002

By Kirk L. Prather

Why discuss techniques of accident prod lot on? Would it not be more useful to discuss means to reduce accidents? This discussion will answer these questions by suggesting ways in which effective accident prediction techniques improve the ability to foresee and prevent accidents. Accident Prediction Process The secret to accident prediction is to utilize the tendency for history to repeat itself. The same circumstances and the same human behavior that produced accidents in the past tend to produce accidents in the present and the future. The ability to predict accident occurence in the future by projecting from the past is a statistical process. In a bookmaker's jargon this means "playing the odds" or "the percentages". A horse or a sports team may be beaten on any given day, but by skillfully assessing the factors of past performance and assigning odds, many clever bettors make money in the long run.

Jan 1, 1973

By William Harrison, Robert H. Trent

GENERAL DESCRIPTION History The most striking feature of mining in the United States has been the infrequent use of longwall systems. This system, which accounts for the majority of coal production in Europe, Japan, and other countries, is only recently growing out of its infancy in the mining of normal coal seams and is still untried in the mining of thick coal seams in the US. Its use in the mining of metal and nonmetal ore bodies has been virtually ig¬nored, except for isolated instances in trona, copper, and uranium. Longwall mining is believed to have originated in Shropshire, England, towards the end of the 17th cen¬tury (Laird, 1973). Although the method used would be considered primitive by today's standards, many of the basic concepts have remained unchanged. Longwall mining of coal in the US was first introduced before the turn of the century, but it never gained acceptance as it did in Europe. Historically, longwalling was a cyclic method where a single cut of coal was removed from the face on the producing shift each day, and the work of building stone packs in the gob and manually moving roof support was completed on the off shifts. Due to the amount of dead work, productivity was extremely low. In Europe, however, longwall methods were required despite the high costs involved, because only by this method could coal under heavy depth be mined with any reasonable degree of recovery. Reserves of coal lying under shallow cover, and therefore minable by room¬and-pillar methods, were long ago inadequate to supply most of Europe's coal requirements. In the US coal min¬ing has historically proceeded laterally with the new mines in virgin areas to replace old mines; in Great Britain, Germany, Japan, and many other countries, mining must proceed downward to greater depths. The depth of cover for most coal operations in the US is shallow, i.e., 61 to 305 m (200 to 1000 ft). This, combined with large reserves, has made room-and-pillar methods almost universally applicable. However, longwall systems were tried around the turn of the century. Whenever used, it was frequently noted that the opera¬tion was under the direction of men with foreign ex¬perience and was tried under ideal conditions. Some of the mines that were using longwall or had tried longwall prior to 1910 were the Radiant mine, CO; Vinton Coal Co., PA; Cambria Steel Co., Johnstown, PA; Grundy County and Spring Valley, IL; and unnamed mines in Washington, West Virginia, Kentucky, Iowa, and Kansas. As late as 1961, there was one circular longwall in operation at Centerville, IA. The first modern-day op¬eration to take advantage of European technology and longwall methods was Kaiser Steel Corp. at its Sunnyside mine near Price, UT. Due to deep cover and extremely poor roof conditions, combined with a need for in¬creased production, Kaiser management decided a new method was required and turned to longwall in 1961. The first longwall consisted of an Anderson Mavor shearer loader, British Jeffrey-Diamond conveying equip¬ment, and Dowty roof supports with a capacity made up of two and three 27-t (30-st) capacity props. After nor¬mal start-up problems, this unit averaged over 454 t (500 st) per shift (White and Palacios, 1976). During and after World War II, technology in hy¬draulics and controls had advanced to the point that self-advancing supports and hydraulic props were being developed. In 1960 only I % of West German produc¬tion was from mechanized longwall faces. This in¬creased to 37% in 1970 and 63% in 1973 (Kohlgruber, 1974). In 1976 there were 246 coal mines operating in the United Kingdom. Although this is only 50% of those operating ten years ago, the production has increased 42%, mainly through improvements in longwall equipment and methods (Hunter, 1976). In France and other European countries, the devel¬opment of longwall mechanization has been similar in seams up to 2.44 m (8 ft) thick. In seams that exceed 9.14 m (30 ft), a variety of longwall caving has been developed for coal seams with dips of 0 to 1.6 rad (0 to 90°). Those with the greatest success will be discussed later. As noted, the development of longwall mining to its present state of the art has mainly taken place since World War II with substantial gains in the last ten years. Mechanized longwall has been the result of several re¬lated major innovations (Jackson, 1975) 1) Development of the flexible armored face con¬veyor which can be installed along the face and moved forward without disassembly. 2) Development of face machines such as single and double drum shearer and coal plows which operate in conjunction with the armored conveyors. 3) Development of self-advancing hydraulic roof supports which now include chocks, chock shields, and shields. 4) Reliance of caving of the immediate roof based on proper planning and development. 5) Use of pneumatic slowing to enable extraction below overbuilt areas. The most recent developments in the mining of coal by longwall in the US include the introduction of shield supports at Kaiser's York Canyon mine in New Mexico, single-entry longwall development at Kaiser's Sunnyside mine, and Mid-Continent's advancing longwall system in Colorado. Metal and nonmetal longwall systems in the US have included the mining of copper at White Pine, MI; uranium in Utah and New Mexico, and trona in Wyoming.

Jan 1, 1982

By James M. Link

The first rule of mineral deposits always seems to be: the deposit is never close to the market. With gems and precious metals, this is not much of a problem. But with most of the mineral commodities used in today's world, transportation becomes a major part of the cost to the consumer. In Japan, for example, more than 60% of the cost of coal to the consumer may be attributed to transportation. The purpose of this article is to examine pipeline transportation, particularly mineral slurry pipelines, as a means of getting the mineral to market. Pipelines Today Regulated pipelines in the US totaled nearly 724 Mm (450,000 miles) in 1980 according to the Federal Energy Regulatory Commission (FERC). Worldwide, more than 210 Mm (125,000 miles) of new pipelines will start construction in 1982 at an estimated cost of more than $150 billion. According to the Bechtel Corp., the period between 1982 and 2000 will see major growth in pipelines of all kinds. In North America, major movements of crude oil from Alaska and synfuels from the Rocky Mountains will require the construction of nearly 16 Mm (10,000 miles) of new pipelines. Nearly 42 Mm (26,000 miles) of new gas transmission pipelines will be needed to tap both US and Canadian arctic gas fields and move the gas to major markets on both coasts. Other pipelines will be required to move additional quantities of natural gas from the Rocky Mountains to more populous regions. Bechtel says more than 24 Mm (15,000 miles) of slurry pipelines will be needed to transport coal from both eastern and western coal provinces to the Mississippi valley and coastal areas. In 1980, 125 companies delivered more than 1 km3 (6.5 billion bbl) of crude oil and 652 hm3 (4.1 billion bl) of products in the US. At the same time natural gas pipelines transported 498 km3 (17.6 trillion cu ft). The reported investment by these companies was nearly $20 billion at the end of 1980. Advantages of Pipeline Transportation The obvious success and vitality of the oil and gas pipeline industry is based, at least in part, on the fact that pipelines are a very efficient and low-cost method of transportation. This fact, coupled with the need for lower cost trans¬portation, has led to the marriage of oil and gas transmission technology and the bulk mineral solids transportation industry. The off-spring of this marriage is the mineral slurry pipeline. Slurry pipelines have a number of advantages over other transportation methods. One of these is the fact that they are buried-out-of-sight, out-of-mind. Second, they are relatively small users of labor because they lend themselves to automation and remote, or even computer control. Third, they offer an attractive economic alternative to other transportation systems. For example, for a 1000 km (621 miles) distance, rail costs of 1?/ km (1.7?/ton-mile) are about equivalent to slurry pipeline costs. But, as the distance increases, pipeline cost per t-km continues to drop while equivalent rail charges remain essentially insensitive to distance. Where existing rail, barge, or ocean ships are available, the cost of new construction associated with a slurry pipeline probably will render it noncompetitive. However, where new rail or other construction is needed, the cost of a slurry pipeline is very competitive. About three-fourths of the cost of a pipeline is in pipe, fittings, and construction. Nearly a fifth of the investment is in pump stations and the remainder is in right-of-way, surface facilities, utility acquisition, communication facilities, and other support areas. The fact that pipelines are capital intensive is, at the present time, a mixed blessing. For example, the delivered cost of coal in a hypothetical project doubles when the cost of money rises from 9% to 17.5% per year. The largest cost element for delivered coal in this example is in depreciation and finance charges. The next largest cost element is electricity to power the pumps, with labor making up the smallest increment of the delivered cost of coal. World Slurry Pipelines The idea of a slurry pipeline was probably first investigated in the latter 19th century, but the first ones were successfully built and operated in the US in the early 1900s. Today, they are fairly common worldwide. Table 1 shows a number of the world's slurry pipelines. An examination of these will further emphasize the fact that pipelines provide a cost competitive alternative where new construction of a transportation system is required. In each of the examples, the desired mineral commodity is located in a remote corner of the world, markets are at a great distance, value of the commodity is not great, and no other transport system is available.

Jan 10, 1982

By Wallace Macgregor

The direct investment role of Middle Eastern oil producing countries in future world-wide mineral development probably will be a limited one for the next five years. Their needs and their longer range economic objectives substantially preclude any such risk taking ventures. There is, of course, the possibility of political in- vestment. One hears many rumors and doomsday calculations of what the Arabs might do with the rising accumulation of surplus funds. Up to now, this kind of investment has been more in rhetoric than in money. For the most part, oil producing countries of the Middle East have been, and will be, investing surplus funds with strong emphasis on the preservation of capital. They will seek security first and yield second just like any other prudent investor. In several respects, this is regrettable. A direct infusion of risk capital into mineral development, especially in the Third World countries, is a constructive way of enhancing their earning power which many desperately need just to stave off starvation. It would also be a good way of eliminating material shortages in the industrialized world. Most important of all, it would help to ultimately reduce inflation without imposing the hardship of recession. So why isn't it done?

Jan 1, 1975

By P. W. King

The performance of the versatile McNally Wedag horizontal vibratory centrifuge for dewatering ultra fine 0.5 x 0.15 mm (28 x 100 mesh) material has proven to be success¬ful and the results presented herein will examine its capabilities in terms of capacity, solids capture, product moisture, effluent solids, and size analysis. Centrifugal dewatering of fine refuse has proven t to be another application for which this unit has performed exceptionally well.

Jan 1, 1985