Search Documents

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By Wolfgang Güter, Paolo Romualdi

Current extensions of the European railway network require long TBM drives in the diameter range of 10 m under critical and varying rock conditions. In view of that and in particular for a 7 km long high-speed railway tunnel in Spain to be started in mid-2003 a new design for a hard rock Double Shield TBM has been developed by SELI (Italy) and Jäger (Austria) in collaboration with Mitsubishi (Japan)and Robbins (USA). Due to the new design and operational features that new type of TBM has been named Universal Double Shield TBM with a further extended area of application. Special attention has been given to outstanding torque and thrust capacities combined with the shortest possible length of an innovative shield arrangement, different advance modes in various ground conditions and further developed exploration and treatment facilities.

Jan 1, 2003

By W. H. A. Timm

Lake Dufault Mines, Limited, is located ten miles north of Noranda, Quebec. Following discovery of a copper-zinc orebody late in 1961, metallurgical investigations of diamond drill core were conducted by Lakefield Research Limited during 1962 and 1963. These were followed by pilot-plant tests in May and June of 1964, utilizing underground development ore. Milling operations commenced on August 16, 1964, and reached rated capacity of 1,300 tons per day by October 1, 1964 (Figure 1). Since that time, tonnage was gradually increased to a maximum of 1,400 tons per day and since January 1, 1968, gradually decreased to the present rate of 1,100 tons per day due to an increase in the hardness of the ore. The ore milled from start-up until January, 1968, was mainly massive sulphides, consisting of a complex mixture of iron, copper, zinc and minor amounts of lead sulphides with important associated values in gold, silver and cadmium (aver- age specific gravity 3.8). From January, 1968, until the present, the ore being processed is described geologically as a boxwork of sulphide stringers of chalcopyrite, pyrite and pyrrhotite and some local dissemination in siliceous rhyolite (average specific gravity 2.9) supplemented by the massive copper-zinc ore. The limited size of the orebody and the mining method employed (open stoping by blasthole and slash and bench methods) would have made grade control from the mine difficult and expensive. It was decided to try to cope with grade variations in the mill. The resulting rapid and wide swings in mill heads, hardness and specific gravity have presented many and varied challenges for the mill personnel.

Jan 1, 1970

By Yoginder P. Chugh

About 65% of the U.S. coal production (835 n tons was surface mined. A similar proportion of the Illinois basin's production (112 m tons) is also surface mined. The state of Illinois is the third largest producer of surface mined coal in the United States, after Wyoming and Kentucky. The Illinois coal basin encompasses Illinois, southwestern Indiana, and western Kentucky, as shown in Figure 1 (dotted lines). The estimated surface mineable coal resources in the basin amount to about 27 billion tons, and about 69 m. tons of coal is surface mined annually (Tab1e I).

Jan 1, 1981

By Felicia F. Peng

The plant data were collected from three streams around a dense medium drum for coarse coal cleaning operated at various volumetric ratio of medium-to-feed. The effect of the volumetric ratio of medium-to-feed (MF) and particle sizes on the performance criteria, g50 and Ep, of the dense medium drum. These measured data were adjusted and calculated for the yields and balanced relative density distributions by mass balanced method based on the statistic principle. These balanced data were then used to formulate the mathematical models of the separation distribution curves for the various feed size intervals. The correlation equations for the g50 and Ep as the function of inverse of the feed size, and MF and total throughput were established. A numerical algorithm utilizing the Secant method, based on the root searching principle, was developed for yield optimization and simulation of dense medium drum separation to improve the separation efficiency and hence the product yield. The relationships between the direct ash content and relative density of the particles in feed and the products were established and incorporated into the numerical algorithm for predicting the product quality.

Jan 1, 1996

By F. Warnaars

Historically, this area produced gold and silver from many well-known vein deposits, like Tayoltita, Topia, and San Jose de Gracia. Modern exploration identified three categories of deposits: 1) low grade porphyry golds in shallow level dacite porphyries; 2) batholith-related deposits; and 3) those formed in volcanic sequences of Late Cretaceous to Late Tertiary. At least four porphyry golds have been identified, of which Metates is best known. These are formed by and within dacite porphyries, associated hydrothermal breccias and sometimes within surrounding metasediments. Their ages are from mid-Cretaceous to Early Tertiary. Precious metal deposits associated with batholiths occur as veins, contact haloes in metasediments or volcanics, skarns, tectonic breccias, hydrothermal tourmaline breccias, dacite dikes or as disseminated or stockwork deposits such as La Fortuna. Several new gold discoveries were made in older Early Tertiary Volcanic Sequences and in the younger Tertiary volcanics within prominent structures exceeding 3 to 5 km in lengths. Some of these are open-pittable but most have to be mined by underground methods.

Jan 1, 1999

By William J. Miles

The major health hazard from exposure to crystalline silica historically has been silicosis. Silicosis is the scarring of the lung from excessive exposure to crystalline silica. It has been recognized as an occupational disease for over two thousand years, since early Greek physicians noted the respiratory problems of miners, stonecutters, and quarrymen who were exposed to excessive quantities of mineral dust. During the industrial revolution, the incidence of the disease was greatly increased by the use of machinery which increased dust levels. Subsequently, the need for dust control was recognized and dust control measures were instituted. Silicosis is characterized by progressive breathlessness on exertion and develops over the course of years. X-ray images of the lungs show progressive scarring of the lungs. The symptoms are related to the amount of exposure to crystalline silica and the years of exposure.

Jan 1, 1990

By H. Habenicht

Requirements for full extraction in underground coal mining call for inexpensive, safe, techniques to be competitive with conventional methods. Longwall and shortwall systems are to some extent employed for this purpose. Another method would be rib pillar extraction (and pillar extraction). These methods are compared with each other with respect to procedure, equipment, safety, roof control, investment, output, performance, costs The advantages of r.p.e. show this method very attractive. Number and cost of equipment are lowest. Safety and roof control becomes improved by a mobile roof support recently developed in Austria. Its successful use in the R.S.A. is being explained.

Jan 1, 1986

By G. Soni

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model has been validated in a series of laboratory batch flotation experiments, in which mono-sized glass beads are used as feeds. The experimental results are in good agreement with model predictions both in terms of grade and recovery.

Feb 23, 2014

By E. L. Gillenwater

Coal mine planning has three distinct decision levels: (1) decisions made at the upper level of management that determine production requirements for specific mines, (2) decisions made at the middle management level, the mine level, that determine how the mine satisfies its production requirements, and (3) decisions made at the operating level of management, the sectional level, that determine the sequencing of machine movements at the face. In this paper, the underground production scheduling problem is formulated in multi-stages using the Hierarchical Production Planning (HPP) approach. Two linear programming HPP models for accomplishing decisions at the first two levels are developed. Both models address the aggregate production planning process. The Mine Production Scheduling (MPS) model permits determination of monthly production and inventory levels. The Section Production Scheduling (SPS) model incorporates a quality blending requirement into the determination of weekly sectional production and inventory levels.

Jan 1, 1995

By Ingemar Marklund

INTRODUCTION Today at LKAB, the primary mining method used is sublevel caving, independent of ore-body size, shape, dip, and geographical location. The mining of small ore bodies with relatively flat dip involves a lot of develop¬ment work, a large initial investment, big dilution, and large ore losses. In 1975 serious investigations into other possible methods, especially for those small ore bodies which do not lie in direct contact with other ore bodies, began. Different methods were studied and a number of in¬teresting ideas came from Russian mines. An analysis was made of one of the proposed methods, sublevel benching, in which mining is carried out from raises, and which uses the throw from the blast to place the broken ore. However, there were reservations about working in big open rooms at great depth, and doubts about the possibility of getting acceptable drilling results in an acceptable environment from raised platforms. Testing was therefore delayed for a time. However the investigations continued and in the fall of 1976, it was decided to try vein mining in a small ore body (Indian) (see Figs. 1 and 2). MINING RESULTS The results are now available from the mining of Indian and are as follows: Ore plan area 1200 m2 Level height 50 m Ore volume 60 000 m3 Ore tonnage 270 000 t Iron content 62% Dip 0.69 rad (40°) Ore thickness 14 m Ore compressive strength 26 MPa Ore C-factor (fracture density) 0.21 Hanging wall compressive strength 28 MPa Hanging wall C-factor 0.27 About 40 000 m of the holes were drilled by ring drills with an average productivity of 85 m/shift; loading of a round (2 rows, 750 m of hole) was usually accomplished in one shift. The total ore recovery was about 270 000 t with an average iron content of 59%, and three to four shifts were required per round (4700 t) to load. The principal of "throwing" the rock during blast¬ing worked well, and no ore remains on the footwall. ROCK CONTROL Before mining commenced at Indian, it was dis¬covered that the rock strength in its vicinity was rela¬tively poor. Since the ore is flatly dipping, and mining was to take place with open rooms, the strength of the hanging wall was of great importance. A supplementary program of exploration drilling was done during the fall of 1976 in order to assess fracture spacing and rock strength from the drill cores. Results showed that the strength of the hanging wall was low because of the many fractures. A decision was made to try cable bolting of the hanging wall by extending some of the ordinary blast¬holes. Cables (20 mm diam) were grouted in these larger holes and the rest of the hole was then utilized for ordinary loading (see Fig. 2). About 100 bolts altogether were installed and, to date, only small falls have occurred and the hanging wall is holding. Its exposed area is 2100 m2 DEVELOPMENT WORK On the 350-m level, four crosscuts (two per mining room), one longitudinal drift, and two elongated drifts (one per raise) for the raise climber were developed as shown in Fig. 1. Of the 230 m of drift, 60 m were in ore and the rest in waste. For mining room A alone, a total of 115 m of drift were needed with 30 m in ore. The drift dimensions were about 4.5 X 5.5 m. In the drifting on the 300-m level, two connecting drifts were driven from one existing transport drift forward to the respective raises. The total development was 93 m, all in waste (Fig. 1). The two raises having a length of 80 m each were driven at an angle of 0.68 rad (39°) from the hori¬zontal. They were driven along the footwall contact with a separation of 30 m and had an area of 10 m2. LONG-HOLE DRILLING The drilling of long holes with the ring drilling unit began in the fall of 1977 in raise A. The equipment consisted of an Alimak raise climber, equipped with a lower platform from which the charging was done.

Jan 1, 1982

By William G. Doepken

After 15 years of production, 91 Mt (100 million st) of ore mined and nearly 227 kt (500 million lb) of molybdenum produced, Climax Molybdenum Co.'s Henderson Mine and Mill are being modernized as a new mining level is brought on line. The $40 million investment in mine development and plant modernization positions the Henderson complex as one of the largest, low-cost primary molybdenum producers for the next 15 years. Henderson history The Henderson Mine and Mill facilities are located on the east and west flanks of the Continental Divide about 80 km (50 miles) west of Denver, CO. The underground mine and surface mill sites are linked by 16 km (10 mile) of railroad tunnel and 8 km (5 mile) of surface trackage. The mine, railroad and mill were built between 1968 and 1976 at a cost of $500 million. Each has operated at various levels of production over the past 15 years. The Henderson Mine was originally developed using a highly mechanized, panel caving mining system. Over the past 10 years, mining methods, equipment and railroad operations have been improved to position Henderson as one of the most productive and lowest cost underground mining operations. At the same time, the mill and concentrator facilities were upgraded to reduce costs and improve product quality. During this time, manpower was reduced from 2000 to 560 employees. These 560 people increased productivity to 54 t (60 st) per total manshift. They reduced operating costs by 50%. And they dramatically improved safety performance. However, as the 1990s approached, the modernization of the Henderson mining and milling complex and the development of the new 7700 mining level became the primary goals to guide Henderson into the 21st century.

Jan 1, 1991

By J. Le Gac, P. Zettwoog, J. Brenot, J. W. Piechowski, J. C. Nenot

INTRODUCTION The components of the radiological hazard in uranium mines are: 1. exposure to radon and its short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation With usual ventilation rates, the dosimetry relative to the first component only requires to know each miner&apos;s exposure to a potential energy of short-lived radon daughters, (EXP[a]). Presently in France, (EXP [a]) is determined monthly from radon concentration measurements. This is an indirect method based on ambient monitoring. After technical improvements achieved during the last years it is now possible to measure (EXP [a] directly with an individual portable monitor developed by the CEA. The purpose of this study is to analyze and compare monitoring results obtained by these methods. DETERMINATION OF INDIVIDUAL MONTHLY EXPOSURES TO[ a] POTENTIAL ENERGY OF SHORT-LIVED RADON DAUGHTERS [(EXP a) amb, by ambient monitoring] In this case, it is necessary to know individual monthly exposures to radon, (EXP Rn). As mentioned by Pradel, J.,et al., 1976, (EXP Rn) is estimated for each worker from informations both on radon concentrations (CRn) measured as described by Pradel, J., 1962 and times (t) elapsed in the various workplaces. (EXP Rn) is obtained by summing up the elementary radon exposures CRn x t relative to all the workplaces where the miner was successively engaged during the month. (EXP Rn) values are then corrected by an average equilibrium factor of 0.17 deduced from many measurements and taken as representative for all the French mines. Finally: [ ] (EXP [a])ind are obtained directly with an individual portable instrument described by Chapuis, A.M., et al., 1972. Samples of the air breathed by the miners are pumped continuously and radioactive aerosols containing the short-lived radon daughters are trapped on a filter. The principle of the measurement lies on track-etch detection of the a particles emitted by the deposited material. The technical aspects have been described by Duport, P., et al., 1980a, Mouden, A., et al., 1980 and Chapuis, A.M., 1980. As mentioned by Duport, P., et al., 1980, fiability is good. Indications on measurement reproducibility are given by Pradel, J., et al., 1977. PRESENTATION OF THE STUDY The underground miner population of a French mine was followed during a period of 8 months (October 1978 - May 1979). Monthly exposure values for each miner determined either by ambient or individual monitoring, (EXP [a])amb or (EXP[ a])ind, had been previously collected by Le Gac, J., 1980, who had also defined miner categories according to the characteristics of the work performed. Four groups are considered here, the "whole mine" and three categories as described in table 1. Data on the individual monthly exposures,(EXP [a])ind and (EXP [a])amb, were taken again to analyze the individual cumulative exposures instead of the "month by month" values. The influence of the mean habits of each individual on its surveillance results is thus taken into account. Each miner has a cumulative exposure as an individual of the "whole mine" and as an individual of each category in which he has worked. The results obtained by ambient or individual monitoring were analyzed (characteristics and adjustements of the distributions) and then compared (description of the discrepancies observed). Obviously, such a study is possible only if all the exposures are cumulated on a same duration. As miners have not worked during the same number of months in the course of the data collecting period, one must considerer the individual average monthly exposures, [(EXP a)]amb and[ (EXP a)]ind, instead of the individual cumulative exposures, which is typically the same thing. To be sure that the exposure values of a given group (A, B, C or D) are representative, only those miners really present for at least 3 months in this group were taken into account. Finally, each individual of the "whole mine" and of the various work categories has a pair of average monthly exposure values : [(EXP a)amb] determined by ambient monitoring and[ (EXP a)ind] deduced from the track-etch recording of the individual portable monitor. Let a miner be engaged during n months[ (3 < n < 8)] in a group, the following relations then apply : [ ]

Jan 1, 1981

By A. Mertzanis

The way and methods used for the surface mining of bauxite until the end of the twentieth century in the area of Ghiona, resulted in a significant burden to the natural environment, especially in the cases where it covered extended parts of forests and forest areas as well as important geomorphological formations. The impacts from the surface mining of bauxite which in fact constitute the object of this study relate mainly to the interruption of the natural continuity of the land relief and the alteration of the natural geomorphological activities and are due to: a) the alternating excavations with fronts of great heights, b) the depositions of large volumes of waste materials which originate from the revealing of the ore and c) the dense road network constructed in order to get access to the mine locations.

Jan 1, 2006

By Robert D. Deister

The Buick Concentrator represents state-of- the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries, lead concentrate grade and reductions realized in reagent consumptions, operating costs and personnel. The productivity improvement discussion is preceded by a concentrator description and a brief history of the process control development at Buick. Current control strategies and future applications are presented afterward.

Jan 1, 1985

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbon-ate gangue from sedimentary apatites "francolite" in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to beneficiate a high Mgo siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for carbonate removal, as mentioned above, and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate, from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the Mgo was rejected in the froth and the phosphate flotation stage produced concentrates analyzing about 31% P2O5,0.7% HgO and 4% insol. The overall P2O5 recovery in the two stages is about 85%.

Jan 1, 1989

By S. R. Clark

"INTRODUCTION Of all the natural resources being taxed by the needs of the modern world, perhaps the most important is the continually expanding demand for water resources. As water becomes scarcer, and increasingly important, new technologies are needed to find innovative ways to preserve this precious resource. In Chile, for example, the mining industry is investing billions of dollars to build desalination plants and pipelines; bringing ocean water as far as 200 kilometers inland to meet their demand and maintain operations. It is a full-blown crisis for that nation and a top priority for their government and economy. It has been reported that world water consumption will increase by 40 percent in the next 10 years, representing nearly exponential growth. In the U.S., as more and more communities continue to be built, more drain on the current water infrastructure is created. For 25 percent of people and operations that rely on water from aquifers, this source is being consumed at a rate that will create significant problems meeting the demand in as few as two generations.1 A PROACTIVE APPROACH When it comes to controlling dust at your operation, whether a landfill, a transfer station, a haul road or another ancillary area, what are the options? We know watering is not the answer, but at the same time, we need to prevent dust from flying to ensure a safe environment and keep our skies clear of pollution, for both regulatory requirements and neighbors. Creating a Dust Mitigation Program instead of looking to buy the first dust control product off the shelf is a first step to conserve water and, at the same time, maintain the operational demands and environmental standards for a given site. The program concept is straightforward enough. However, the process of effectively constructing and executing a program is quite involved. When undertaking a program, each manager needs to work with their team and their partners/vendors in analyzing the following elements: 1. Site Expectations—It is important to understand how to balance your internal standards with your regulatory requirements, as well as how to keep your neighbors satisfied. 2. Site Aggregate—Variations in native soil, such as clay content or gravel levels, greatly affect the approach that will yield the highest results. 3. Climate—Relative humidity and seasonal variations are critical to achieving predictable results through product choice, application frequency and timing. 4. Daily Traffic—The type and frequency of traffic is an essential variable for site management. 5. Environmental Responsibilities—If you have additional, specifically defined responsibilities, the approach to your site may vary. 6. Budget—While efficiency is the goal of any program, some sites will have more stringent restrictions than others. 7. Current Usage Rates—Document and understand where you’re starting from, both with water, supporting products, and maintenance so that effective measurement of results is possible."

Jan 1, 2018

By George F. Swindle

This paper discusses a composite of two coal reserve studies, each of which made use of a computer-based modeling system to assist in an evaluation of multi-seam deposits. The model permitted simultaneous consideration of seam thickness, seam structure, overburden thickness, over-burden ratio, and quality parameters for sulphur content, ash content, BTU values and the EPA Compliance index. The model is designed for use by a non-programmer, geologist or mining engineer. It enables the user, from a computer terminal in his office, to specify constraints (for example maximum um sulphur and maximum- ash content, minimum seam thickness and minimum BTU rating), and produces a report showing the volume, quality and location of that part of the total in place deposit satisfying all the constraints.

Jan 1, 1983

By James E. Monsees, Wayne A. Carbiener, Michael R. Wigley

This paper illustrates an approach to quantitatively document the degree of technical conservatism to be incorporated into the design of a waste isolation system in bedded salt. It is anticipated that for an actual repository site the key performance constraints and/or design bases identified in this paper will be reviewed, and modified or supplemented as required. Ultimate acceptance of a repository will be dependent upon scientific peer input and scrutiny of the demonstrated conservatism inherent in each specific repository site and design.

Jan 1, 1981