Search Documents

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By Zhiyuan Shen, Dan Zhao

The abstract discusses the importance of reliable mine monitoring systems for preventing accidents. It focuses on diagnosing ventilation system failures caused by roadway faults that alter airflow resistance. The paper proposes using an improved Support Vector Machine (SVM) method to identify the fault location based on changes in air volume detected by wind speed sensors. The approach involves building a sensitivity 0-1 matrix and establishing a roadway fault scope library. The improved SVM method is tested on the Daming coal mine, demonstrating its effectiveness in diagnosing fault locations, reducing training time, and improving accuracy compared to traditional SVM.

Apr 5, 2022

By U. K. Custred

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. This trend contrasts sharply with the reduced phosphate rock production levels of the 1966 - 1971 period. The natural consequence of this growing phosphate rock market is an evaluation of the variety of means whereby plant capacity can be most effectively increased. One approach toward increased plant production capacity is through large capacity flotation cells provided they can be successfully applied to the recovery of the relatively coarse product which is characteristic of the phosphate rock feed. This paper will summarize the results of a nine month evaluation test program, conducted at the Haynesworth Mine at Bradley, Florida in which the flotation circuit "specific capacity" (tons feed/ft.2 floor space) and "specific input power" (Hp/ton feed) were determined, and the feasibility of achieving economically acceptable concentrate grade and recovery levels was demonstrated, using large, high capacity, flotation cells.

Jan 1, 1974

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of U.S. coal mining companies are beginning to develop coal seams previously thought to be coo deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas contained in coal beds increases with depth, and ventilation requirements are much more stringent for deep underground coal mines than for shallower mines. When the longwall mining method is used at great depths, ventilation, ground control, and operational considerations must all be addressed in the design of longwall panels. This paper examines the influence of these factors, particularly ventilation and operational considerations, upon the feasibility of two, three, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1986

By J. G. Groppo, B. K. Parekh

A series of performance studies were conducted using countercurrent column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia using a 150-mm (6-in.) inside diameter column that was 5.8 m (19 ft) high. Both thickener feed and classifying cyclone overflow with a typical size distribution of 150 µm (100 mesh) X 0 were tested. The percent solids of the column flotation feed varied from 1.5% to 15% while the ash content ranged from about 30% to 60%. The concentrates produced contained 2% to 10% ash with Btu recoveries of nearly 90% using 0.12 to 1.25 kg/t (0.25 to 2.5 lbs per st) fuel oil and 0.12 kg/t (0.25 lbs per st) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from seven different seams are discussed as well as scale-up relationships used to design a full-scale installation presently in operation.

Jan 1, 1991

By D. T. Jr. Tarr

History of Development The hydrocyclone, probably because of its basic simplicity, has been used for various classification applications since before 1890. A patent was granted in the United States in 1891 to Bretney on a device for separating sand from water, collecting the sand in a closed chamber for intermittent discharge, practically identical to some present-day water desanding cyclones. Between 1900 and 1937 there were 30 or more additional patents issued on liquid cyclone configurations or their use. About 1937 liquid cyclones began to be used commercially in the treatment of cellulose fiber in the pulp and paper industry separating contaminating particles from the fiber in water suspension used for making high grade paper products. Nichols Engineering & Research Corp. of New York was marketing a liquid cyclone for cleaning sand and din particles from fiber suspensions in the pulp and paper industry by 1937. The designs during this period were such that the cyclones discharged a small amount of relatively high density material into a chamber connected to the cyclone apex which in turn discharged the collected dirt material intermittently. By the early 1940s hydrocyclones as we know them today began to appear both in the pulp and paper industry and in coal prorzssing.18 Considerable experimental work was done on small, mostly 3-in.- diam, cyclones operating at relatively high pressure drops, in the range of 50 psi, to remove very small contaminating particles from cellulose fiber in the production of high-grade writing papers in the paper industry.18

Jan 1, 1985

By Shiou-Chuan Sun

The froth flotation of coal, differing greatly from that of most minerals1-5, is not improved but rather impaired by temperatures higher than room temperature6-10 This phenomenon has long taunted us for an explanation. Gayle and Associates 8,9 reported the lack of relationship between their contact angle measurements and their flotation of American coals under various temperatures. Bailey and Whelan6 stated that the viscosity of flotation reagents, offering some clue for their flotation of British coals at low temperatures, could not be put forward as an explanation either in whole or in part for the effect of temperatures on coal-flotation. In this paper, a froth hypothesis is proposed to explain the flotation behavior of coals under various pulp temperatures. Test work involved the flotation of coals and the frothing of reagents.

Jan 1, 1966

By Negar Elhami Khorasani, Anthony Tessari, Nan Hua

Fire hazards can cause severe and irrecoverable damage to reinforced concrete (RC) tunnel linings, threatening the serviceability and resilience of transportation networks. This paper first examines the existing methodologies that are used to classify damage to tunnel linings from fire. These approaches are then supplemented with the results of advanced modeling and inputs from industry experts to propose new fire damage/ repair classifications with the associated thresholds. The results of the presented research can be used to guide fire risk assessment as well as the performance-based design of tunnel fire protection.

Jun 13, 2023

By Chee Theng

"What do you think are the most important topics in mineral processing today? It is a question that begs to be asked when more than 100 of some of the best and brightest in Colorado mineral processing and their invited guests are gathered in one room. They are there for the 66th Annual Colorado MPD Meeting held at The Broadmoor in Colorado Springs: three days of finely curated talks and social events where participation was strong, and information was exchanged and connections forged in a relaxed, informal atmosphere.Water, tailings and social licenseNot surprisingly, water management, with the associated issues of tailings and social license, was high on the minds of those present. The Mount Polley and Samarco tailings dam failures have had repercussions across the industry. “There are big challenges with respect to tailings, and social and environmental pressures to find better ways to treat them,” said Steve Hearn of Huntsman Corp., a view echoed by Bob Kilborn of Kilborn Group LLC. Metso Minerals director Keith Butler said, “Water conservation is a key issue today. Many mining activities are now located in remote areas, so it has social and economic impacts on mining operations.” For Brian Olson of Samuel Engineering, wastewater and reclaimed-water treatment is interesting.Fittingly, the first talk of the meeting was on dry stack tailings by Michael Blois of Takraf USA, who went over both the advantages and disadvantages. “The average now is over one tailings dam failure a year,” Blois said, “and that is one too many.” But the technology may not be the right fit for all projects. In his talk on the KSM project, Jay Layman, president and COO of Seabridge Gold, showed how it isn’t practical for KSM and how Seabridge reached the decision on a cyclone sand tailings managementfacility as the preferred management strategy.The luncheon keynote also dealt with a tailings pond spill, but of a different kind. Bob Schafer, chief executive of Eagle Mines Management, spoke on the federal missteps that led to the spill into the Animas River from the Gold King Mine, a mine that had been a dry mine throughout its life and up to the 1990s."

Jun 1, 2016

By Van E. Housman, Stephen D. Hoffman

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), also known as "Superfund", requires a listing of sites that have known releases or threatened releases of hazardous substances, pollutants, or contaminants throughout the U.S. When EPA determines that a significant threat exists, it places the worst contaminated sites on the National Priorities List (NPL). CERCLA provides EPA broad authority to clean up hazardous sites that threaten human health and the environment. There are currently 52 sites on the NPL that were placed on the list because of high human health or environmental risk as a result of non-coal mineral extraction, beneficiation, or processing operations. This list covers mining sectors from aluminum to zinc. While some of these sites were abandoned, many are still operating. (There are additional mine sites that have been recently proposed to be included on the NPL that are not included in this paper.) EPA is continuing to develop a mining program to address human health and environmental threats from active non-coal mines. EPA has performed a comprehensive study to assess the waste management practices at all of the 52 mine sites on the NPL. In addition, EPA is continuing to collect information on the specific mining sectors (i.e., gold, copper) that represent many of the NPL mine sites. One of the goals of this effort is to attempt to identify the types of mining practices that lead to human health and environmental problems at the NPL mine site. EPA estimates that there are currently 500 to 1,000 active mines (not including placer operations). While some mining NPL sites began operations before the turn of the century, only a handful of the NPL mines entirely ceased operations prior to 1970. Of the 52 NPL sites studied by EPA, 12 are currently active. By definition, these mines represent current mining practices. Approximately 17 additional NPL mines that ceased operations between 1970 and 1990 represent some degree of current mining practices. Therefore, at best, less than half on the 52 NPL mine sites can be said to definitely represent past mining practices. Although some mining waste management practices have changed over time, the basic technology for extraction and beneficiation of mineral ores have remained fairly constant over the last fifty years. While the use of acid to leach copper dumps, the use of cyanide to leach gold in heaps, and the spread of solvent extraction techniques has changed some aspects of mining, the basic operation of removing ore from the ground and concentrating it through beneficiation has remained fundamentally the same as when most of the non-active

Jan 1, 1992

By B. J. Scheiner

The presence of organic materials in gold ores cyanidation. The presence of organic materials interferes with gold extraction by The carbon contained in the ore has been shown to adsorb gold cyanide complex from solution. Removal of the carbon content by roasting or chemical oxidation prior to cyanidation results in gold extractions of 85 to 95 pct. This paper by the Bureau of Mines, U.S. Department of the Interior, discusses how the mineralogy of the carbonaceous gold ores affects gold recovery by cyanidation. It also discusses the advantages and disadvantages of roasting and chemical treatment to render the ore amenable to cyanidation.

Jan 1, 1987

By Brian Fulcher

The Fort Lawton Parallel Tunnel was built in 1990 - 1991 by Morrison Knudsen Corporation (MK) as an integral part of Seattle METRO's planned expansion of the Westpoint Treatment Plant. The project included a concrete lined 2542 m (8,340 ft) long tunnel bored in sands and clays under the presence of methane gas and over 27.4 m (90 ft) of ground water table. The tunnel roughly paral¬lels an existing and still operating 3.65 m (12 ft) diameter tunnel originally completed in 1909. The parallel tunnel was constructed using a Lovat 4.72 m (15 ft-6 in) earth pressure balanced TBM with ribs and timber lagging as primary support. The tunnel alignment crossed under as much as 91.4 m (300 ft) of overburden as well as twin mainline railway tracks; terminating in a shaft adja¬cent to the Seattle ship canal. The project was completed in June, 1991 after a final "wet-tap" tie-in to the existing brick-lined sewer; over five months ahead of the contract schedule. This paper will describe the construction methods, job site conditions and difficulties encoun¬tered on this very challenging and successful project.

Jan 1, 1993

By Robert Stefanko

The importance of underground stress instrumentation cannot be minimized. It was Lord Kelvin who said that unless you can assign a number to a quantity,, you know very little about it. Most engineers will agree although this kind of statement is resented by our friends in non-technical fields. Mining is undergoing a revolution from art to science. But how can mining methods be optimized if there is no way of measuring the effectiveness of a given mining method? Do we know how effective a' support is unless we can determine its reaction to the mine structure? How do we assess the need for modifications to existing systems and supports, and how do we measure the effectiveness of such changes? Cut and try techniques are too wasteful of time and energy, and rarely provide solutions to a given problem. The purpose of underground stress instrumentation is to provide answers to some of the above questions -- answers that cannot be obtained otherwise This does not mean that laboratory studies are not valuable -on the contrary. Laboratory and underground studies supplement one another. Rock mechanics had its conception with the study of stresses in homogeneous, isotropic, and elastic models subjected to various force systems. These analyses were valuable inasmuch as they pinpointed possible sources of trouble due to stress concentrations. If the results observed underground did not always agree with the experimental analysis, it was not an indictment of the latter. More probably, the discrepancy could be attributed to the lack of similitude between model and prototype. The more nearly one can simulate underground conditions in a model, the more apt one is to produce results which correlate well-with underground observations. It is impossible to completely simulate underground conditions because all of the significant design parameters have not been recognized and evaluated. What better way can one evaluate these parameters than by underground stress instrumentation?

Jan 1, 1963

By N. Kuroda

A realistic simulation model has been used for designing longwall mining, especially for solving operational problems. This paper describes background, development, validation and some applications of the simulation model for mining people who are unfamiliar with O.R. or computer technique, as a simple planning tool. The following items were established: logical analysis and algorithmic design for practical longwall mining, structure of hypothesis behavioral organism, input parameters, using practical knowledge and operational statistics of the mechanized longwall system experienced for many years.

Jan 1, 1982

By D. Kang

The adsorption behavior of silver in ammoniacal solutions on to activated carbon has been studied. The parameters affecting the adsorption of silver on to activated carbon included temperature, agitation speed, concentration of cations and anions as well as that of ammonia. It was found that the adsorption of silver from ammoniacal solutions was dependent upon the initial silver concentration in the solution and other factors. The recovery of silver from ammoniacal solutions was found to be not so effective as the case with gold reported earlier. The adsorption rate was relatively slow overall, despite a rather fast initial adsorption. The apparent activation energy for the adsorption was measured to be 30.2 kJ/mol. It was believed that the kinetics of the silver adsorption on activated carbon was limited by a mixed control mechanism.

Jan 1, 1998

By L. A. Roe

The year 1867 marks the first year of commercial production of phosphate rock in the United States. South Carolina produced almost all of the domestic output of mineral phosphate until phosphate mining began in Florida in 1888. During the period 1868 to 1949 the total marketed production of domestic phosphate rock was about 186 million long tons of which 71.5 percent was produced in Florida, 18 percent in Tennessee and 7 percent in South Carolina (1). From 1949 through 1960, Florida phosphate rock production has ranged Prom 71 to 77 percent of the total domestic production. Since three-fourths of the domestic phosphate production is from the Florida field, and since most of the phosphate from the Tennessee and Western fields is not processed, but used directly as electric furnace burden, this paper will concern itself almost entirely with water requirements for mining and processing ore from Florida. Figure 1 summarizes phosphate rock production for Florida vs. total United States production over the period 1947-1960.

Jan 1, 1962

By A. McCombs

Previous models describing the aggregation of polymer-coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called "active" sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1988

By Jeffrey P. Chanton

A specialized Pore-Fluid Array sampler (PFA) was designed to collect and store pore-fluids to monitor temporal changes of ions and gases in gas hydrate bearing sediments. We tested the hypothesis that pore-fluid chemistry records hydrate formation or decomposition events and reflects local seismic activity. The PFA is a seafloor probe that consists of an interchangeable instrument package that houses OsmoSamplers, long-term pore-fluid samplers; a specialized low-dead volume fluid coupler; and eight sample ports along a 10-meter sediment probe shaft. The PFA was deployed at Mississippi Canyon 118, a Gulf of Mexico hydrate site. A 160-day record was acquired from the overlying water (OLW) and 1.3 meters below seafloor (mbsf). Fluids were measured for dissolved chloride, sulfate, and methane concentrations and dissolved inorganic carbon and methane stable carbon and deuterium isotope ratios. Chloride and sulfate did not change significantly over time, suggesting the absence of gas hydrate formation or decomposition events. Over the temporal record, methane concentrations averaged 4 mM at 1.3 mbsf and was thermogenic in origin (d13C-CH4 = -32.4±3.4?). The timing of an anomalous 14 mM methane spike coincided with a nearby earthquake (Mw=5.8), consistent with the hypothesis that pore-fluid chemistry reflects seismic events. Keywords: Osmosampler, gas hydrate, methane, stable isotopes

Jan 1, 2008

By Rainer Antretter

While respirable crystalline silica (RCS) dust that arises in industrial production mostly emanates from point sources and can be well mitigated, the extraction of dust is much more difficult in underground construction, since locally generated dust spreads widely. Analysis of dust measurements shows that RCS values are difficult to predict, and effective dedusting systems are required to comply with permissible exposure limits (PEL) in breathed air. Dedusting systems are effective near the tunnel face, while dedusting of working areas away from the tunnel face is difficult or even impossible. In general, there is little temporal influence on the tunnelling work—except for drill and blast excavation—which makes it necessary to remove the deduster and ductwork from the face area. Concurrent work in the tunnel is affected by the backflowing air mass of ventilation and therefore the quality of this air mass must be considered. The use of personal protective equipment (PPE), e.g., dust filter masks, is considered the least-desirable safety measure available. However, for certain individual operations in the tunnelling process, the use of PPE cannot be avoided, especially if other technical mitigation measures are not possible. In tunnels with small cross sections for example, dedusting systems often cannot be accommodated and PPE must be used instead. This raises the question of whether the use of PPE can be avoided by designing appropriate excavation cross sections and allowing for the implementation of technically engineered mitigation measures. The paper highlights problems with dedusting measures and shows possible ways to achieve OSHA compliance.

Jun 13, 2021

By K. V. Viswanathan, P. Sornasundaran, S. E. El-Mofty

Dolomite is found to undergo preferential dissolution in aqueous solutions and this is found to be strongly dependent on the solid to liquid ratio (SIL). Electrokinetic studies done under the sump conditions revealed that the mineral surface charge is also affected markedly by the solid content in the suspension. Conditioning of the dolomite at low SIL ratios for short time intervals showed preferential dissolution of calcium leading to a magnesium-enriched dolomite surface. At higher SIL ratios and longer conditioning times, calcium depletion from the solution and a calcium-enriched dolomite surface resulted. The results are discussed in terms of surface precipitation and/or bulk precipitation and surface conversion of dolomite to the calcium-enriched phase (calcium carbonate and/or magnesian calcites).

Jan 1, 1990