Search Documents

By L. G. Hendrickson

Direct-reduction processes for converting iron ores to metallic iron in the solid state have been available for some time; and whenever scrap becomes expensive, there is a new wave of interest in these processes. It is well established that direct reduction, coupled with electric-furnace steelmaking, is a technically viable method for making steel and in some circumstances is economically competitive with the conventional blast-furnace--basic-oxygen-process (BOP) route to steel. This raises a number of interesting questions, several of which could be of great interest to the coal and ore mining industries. For example, what are the quality requirements of the raw materials for direct-reduction--electric-furnace steelmaking? Would they be different from the present requirements for blast-furnace--BOP steelmaking? Other questions relate to how much steel will be made by the direct-reduction route in the future. The quality questions can be discussed with a fair degree of certainty, but a prediction of the amount of steel that will be produced by the direct-reduction--electric-furnace route is beyond the scope of this paper. However, an attempt will be made to identify some of the factors that will influence whether there is a swing to direct reduction and the rate at which it may occur.

Jan 1, 1978

By William E. Mead

Although this paper has been entitled "Design of Embankments for Tailings Ponds and Waste Dumps," a better title might have been "Site Selection and Design Planning for Tailings Ponds and Waste Dumps," The procedures normally followed in performing the engineering calculations based upon the measured soil properties will not be detailed. Instead, we shall look at the subject in broader perspective which considers the environmental factors and the fundamental design principles. Disposal of waste materials left from the extraction and processing of mineral deposits has become, in recent years, an important engineering consideration for mine and mill operators. Land occupancy and land values almost everywhere are increasing at a rapid rate. So is the size of mine and mill waste dumps, thanks to our advancing technology in mineral beneficiation. Mining companies are being pressured to "clean up" their operations, both literally and in a safety hazard sense. Once, long ago, the miner could use any convenient location to get rid of his mine waste and mill tailings without being concerned over possible infringement on the rights and well-being of the public. Today, however, he must pay close attention to these matters if he wishes to avoid liability suits and the unfavorable reaction of civic groups as well as local and regional government. Most operators keenly sense their increased responsibility, not only because they are legally vulnerable, but because they realize the necessity for sharing space harmoniously with the rest of society.

Jan 1, 1967

By I. F. Walder

Mill tailings from skarn-type base metal deposits were studied in order to ascertain potential element mobility in response to weathering. Hypogene ore minerals are sphalerite, galena, and chalcopyrite, showing minor supergene oxidation to smithsonite, cerussite, and covellite. Gangue minerals are pyrite, pyrrhotite, magnetite, hematite, andradite and grossular gamet, hedenbergite, calcite, ankerite, and quartz. Foremost of the eleven tailing piles studied, the hypogene sulfide minerals show no or only incipient post-mining oxidation. Iron oxides and hydroxides form the main oxidation products in the tailings and are enriched in heavy metals. A distinction between pre-and post-mining oxide phases may be obtained based on petrographic observations which distinguish whole-grain versus partial grain replacement. Zn and Cd do not appear to be enriched in the weathering derived oxidation minerals and will be more easily leached from the tailings than other metals.

Jan 1, 1994

By Craig Allan

Underground construction environments, especially those with limited airflow such as shafts, cross passages, and stations, necessitate effective dust control. This requires combining existing measures with adapted approaches for more efficient and productive operations, cleaner jobsites, and decreased worker exposure to contaminated air. This paper will discuss new configurations and trends in dust collection on Australasian infrastructure projects including WestConnex, Melbourne Metro Tunnel and City Rail Link, all of which have applied innovative methodologies for mobile at-source dust collection. Mobile dust collectors can be track-mounted dust collectors operate alongside equipment, use hydraulic stepping systems to advance with roadheaders, or compact castor-mounted units are used within cross passage confines.

Dec 1, 2022

By Ashma Singh, Nichole Maistry

Due to declining iron ore grades, low-grade ores with complex mineralogy — namely, banded iron formation (BIF) — are being explored to maximize iron ore resources and increase the life of mine. Flotation is the standard global process used for the beneficiation of BIF ores, as it is a complex ore reserve, and liberation is typically achieved below 1 mm. This study focuses on the flotation of a South African BIF, evaluating its response to different collectors, as well as effect of grind. As flotation is an expensive process and South Africa ranks high on the production cost curve, preconcentration by gravity or magnetic separation is performed prior to flotation. Thus, flotation was also performed on a gravity concentrate to determine if a grade suitable for steelmaking (approximately 63 percent) is achievable. The results indicate that the use of an alkyl ether amine-based collector partially neutralized with acetic acid is suitable for separation of hematite from illite and quartz at high pH values. Further optimization tests are being pursued to improve overall recovery and grade.

May 1, 2025

By B. K. Cantrell

A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2, NO, NO2, SO2, diesel-exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive, but during the past several years, progress has been made in defining the problem. Results from epidemiological studies by Garshick, et al. (1988); animal inhalation studies by Mauderly, et al. (1986); Iwai, et al. (1986); and Brightwell, et al. (1986); and in vitro studies by Lewtas, et al. (1986), have provided sufficient data for the National Institute of Occupational Safety and Health (NIOSH) to recommend that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration," NIOSH (1988). NIOSH further stated that "though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk."

Jan 1, 1990

By B. R. Addison

In the Spring of 1991, Georgia Marble Company of Arizona (GMCOA), acquired the Andrada Marble Company located near Vail, Arizona, approximately 32 km southeast of Tucson. The Georgia Marble Company operation consists of an open pit quarry and a recently constructed, state of the art calcium carbonate milling and processing facility. The open pit quarry exposes white, crystalline, CaCO3, Escabrosa limestone that meets our customer criteria for Consumer and Industrial Filler applications. The Georgia Marble Company Arizona Division facility is designed and engineered to produce a wide range of milled calcium carbonate that includes finely ground and coarse screened products.

Jan 1, 1994

By M. Moss Stanley, Ronald P. Klepper

The objective of this chapter is to provide data that will assist in the selection and sizing of equipment utilized in the filtration method of separating solids from liquids. It should be recognized at the outset that in some situations more than one option may be available to achieve the target desired. In some cases purely technical objectives may be sacrificed because of cost considerations, design factors or other elements in order to satisfy optimization within the flowsheet and/or to provide bottom line results. Before considering available options, and prior to the next step of sizing out the selection, the operating criteria should be set down. The test work to develop selection and sizing data will be based on this data and the final products desired. This will help to establish initial parameters. A. GENERAL DATA 1. Material to be filtered: a. Solids b. Mother liquor 2. Feed rate of slurry in GPM 3. Density of slurry: Sp. Gr. Solids 4. Slurry: Temp. pH Viscosity 5. Source and method of feed 6. Valuable product: Solids Filtrate Both 7. Details on: Volatility Toxicity Stability 8. If flocculant is indicated, what has been used? 9. Describe product: (i.e., fibrous, cor 10. rosive, abrasive, inflammable, explosive, pasty, 11. Does product alter or require special environment during transport? 12. What type of filter media has been used successfully? 13. Is there any objection to use of a filter aid? If not, is there any preference? B. SOLIDS DATA 1. Sp. Gr. Bulk density 2. Screen analysis 3. Desired percentage moisture in cake 4. Solubility (state conditions): In mother liquor In wash water 5. Description of cake: (i.e., amorphous, fibrous, crystalline, colloidal, gran¬ular, thixotropic, 6. Special requirements for moisture de¬termination? 7. Can solids be compressed during dewatering? 8. Proposed product handling 9. Subsequent thermal drying or other pro¬cedure C. FILTRATE 1. Is separation of wash water and mother liquor desirable?

Jan 1, 1986

By M. Misra

The dissolution of mercury during gold cyanidation is the cause of many environmental, health and processing problems. A study was undertaken to find a suitable reagent for the removal of mercury bearing complexes from the leach liquor. Removal of mercury from synthetic solutions and process water from a gold mine was investigated using sodium sulfide, sodium and potassium dimethyl dithiocarbamates as precipitating reagents. The results have shown that efficient mercury removal could be achieved by addition of potassium dimethyl dithiocarbamate (KDTC), by formation of stable mercury compounds. The resultant mercury-potassium dimethyl dithiocarbamate precipitates are stable under present plant operating conditions and do not have any deleterious effect on gold adsorption by activated carbon. Furthermore, it is also possible to stabilize the mercury in the heap during cyanidation by adding dimethyl dithiocarbomate.

Jan 1, 1998

By V. A. Kharchenko, V. M. Yeremeev

INITIAL PRECONDITIONS To solve tile problem of using the potential reserves of the different coal ranks efficiently (the coal reserves being many times superior in quantity to those of natural gas and oil) one must realise an integrated estimation of the coalfields' and coal deposits' reserves. The actuality of this problem increased especially in the recent years, when the Russian coal industry is being restructured. A structural reorgaisation of this industry, in order to in- crease its efficiency, covers a large spectrum of social and economic problems, comprising a withdrawal from mining the coal reserves that are unsafe from the standpoint of economy and labour protection. According to the information supplied by the 'Rossoogol' company, the Russian coal industry, accounting for abut a fifth of the world coal reserves, has a rather unsafe resource base, for about 5% of the reserves involved in mining do not correspond to the world practice conditions, regarding the coal grade, thickness, geological conditions, proneness to coal and gas outburst hazards. These concern first of all the Moscow, Kizelovsk and Donetsk coal basins, the Prokopievsk-Kiselevsk district of the Kuzbas basin and several other coalfields. Thus, the problem of efficient potential coal reserves' utilization calls for a paramount solution of two basic problems, namely: a) a comparative coalfields' and sections evaluation, and their ranging, in accordance with their industrial importance; b) choosing the 'active' reserves good to be efficiently mined under the present-day conditions. PRINCIPLES OF EVALUATION The investigations that had been carried out make it possible to formulate the following basic principles of the coalfields' reserves' estimation (or assessment). 1. The necessity, possibility and expediency of coal reserves' industrial exploitation are determined by a set of natural, technical, technological, practical, economic, environmental and social factors, thus calling for an integrated and gradual approach to problem solving. 2. One cannot consider the results of same reserves' estimation as being invariable because the former depend both upon constant (mainly natural) and market demands for different grades of coal (those of different power engineering and technological situations), capital investments, material and labour resources, economic (price-forming), technical, technological, environmental and other factors. 3. The rational size and sequence of the operating mines' and reserve sections' resources' involvement into mining depend upon the final aim of posing the problem, whose variants may be (the corresponding limitations being considered) providing for a maximum run-of-mine output (these essentially featuring the past stages of the industry's evolution); providing for a maximum efficiency, measured possibly by the specific or absolute indices of profits an expenses, labour productivity e. al. ; providing for a maximum extraction (maximum integrate utilization) of the known reserves. In this case an important park goes to the economic evaluation (or assessment) of useful application of the by-products being extracted (methane, mine water, rack) compared to the expenses necessary for their utilization. Regarding the steam coal (posing the problem any way it be possible), and extreme limit to the absolute non-efficiency of the coal reserves' exploitation may be posed, using the proportion of energy obtained from the possible amount of the coal to be extracted to the energy consumption necessary to extract, prepare, haul and consume this amount of coal. 4. The most reliable and efficient solutions providing for opening the reserves can be obtained for group of mines, rather than at the level of an individual mine section or an individual mine because it is only in the former case that the possibilities to re- distribute the expenses necessary to develop the good for mining and worse sections and seams can be realized to the greatest extent. Therefore the prospective approach to be considered is the one providing for an integrated organization and choice of the optimum combination of the variants of the ways to use the mines in operation and the free sections of the region in order to satisfy the growing up requirements for coal rather than the one providing for individual mine sections' resources' evaluation. 5. The future possibility and expediency of coal reserves' industrial exploitation will depend upon the prospects to implant at the mines in operation and reserve sections new engineering and technological elements and coal extraction technologies which may essentially change the actual idea concerning the coal reserves worth of being developed in an efficient way. For example, reserves not available to be exploited using conventional coal extraction technology may be regarded as potential resources for in situ gasification, e. g. the operating mines' reserves (non-commercial and non-mined commercial ones), balance and outside balance reserves of the free sections having proved not available to be mined using conventional coal-extraction technologies, as well as the non-extracted reserves of the abandoned and closed mines.

Jan 1, 1996

By L. J. Lindsay

Kaiser Resources Ltd. operates a coal mining complex in Southeastern British Columbia. A large surface mine, a conventional underground mine, and an innovative hydraulic underground mine are presently in operation. The products of these mines are fed to the Elkview plant. This coal has to be prepared to 9. 5% ash and 6'o total moisture for export from the port of Roberts Bank near Vancouver, British Columbia to Japan at a rate of 4. 5 Mltpy. The moisture requirement for the coal product was recently increased to 8. 0% total moisture. The entire operation has been described in various publications (1), (2), (3). Details of the venture will not be repeated in this paper. In this paper we hope to describe the modifications made to the original coal preparation plant in order to satisfy market requirements for quality and quantity of coal.

Jan 1, 1974

By John A. L. Campbell

Surface dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or imporve a surface dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and flocculation. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established (1). These data will be presented at a latter date.

Jan 1, 1969

By B. L. Bobo

To ensure the continued growth and economic viability of the Western coal industry, both in the domestic and inter- national markets, it is essential for the industry to become more creative and active in confronting the most serious obstacle in this objective; and that is, the inherently long distances which Western coal must be transported inland to reach its major markets. Figure 1 shows the 1982 coal consumption by state for those states where Western coal was consumed. (Except as noted in this paper, Western coal producing states are defined as Colorado, New Mexico, Arizona, Utah, Wyoming, Montana and North Dakota. Any exceptions used will have only an insignificant effect on the content of the paper). This figure illustrates the long distances that are required for Western coal to reach its markets. The total production for 1982 from the Western coal producing states was approximately 220 million tons, of which only 85 million tons was consumed within the boundaries of these states. The remainder was transported to markets outside the area. This map also shows, based strictly on the consumption of the states to which Western coal was shipped during 1982 and not considering other factors which are involved in the marketing of coal, the total market potential of Western coal would amount to a total of 445 million tons. This does not include export coal from the West Coast, which is now estimated to be less than 2 million tons for 1983. In 1980, it had been estimated that by 1985 the West Coast exports would have been at least 10 million tons per year, which will not be attained.

Jan 1, 1983

By S. D. Thompson, L. Adler

This study reviews and analyzes the empirical methods available for designing the capacities of coal mine gathering belts. The analyses lead to recommendations concerning the application and implementation of each empirical method. Operations research techniques, mainly simulation models, are also briefly mentioned, and a few recommendations are made concerning their selection and application. The objective of the study is to provide a reliable basis for the practicing engineer to properly select, apply, and implement a capacity design method.

Jan 1, 1988

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

This paper presents the results of an investigation into the effect of pore pressure regime on the factor of safety (FS) and the anticipated critical failure mechanism for a fly ash storage facility. In this study, pore pressure measurements from standpipe piezometers and pore pressure estimated from seepage analysis were used for a comparison of the estimated FS for a fly ash slope. This comparison was applied for static and seismic scenarios. To account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation, a probabilistic analysis was performed. The slope stability analysis was conducted in 2D and 3D, adopting the limit equilibrium analysis approach, and a finite element seepage analysis. The results suggest consistency of failure surfaces for 2D and 3D and an increase in FS values of 5 percent for the 3D approach, limitations of standpipe piezometers. The study demonstrated the sensitivity of the FS value, and the implication of adopting representative material properties, and water table levels, especially in cases where limited data are available, and assumptions need to be made to assess the long-term stability of a fly ash dam facility.

Aug 1, 2024

By B. Pesic

Manganese is about twelfth in the list of the most abundant elements in the earth's crust (Reidies, 1981). More than 150 known minerals contain manganese as an essential constituent (Mellor, 1932). In general, ores containing at least 35%Mn are classified as manganese ores, ores with 10-35%Mn are called ferroginous manganese ores, and ores containing 5-10%Mn are known as manganiferrous ores. One very important class of manganiferrous ores are manganiferrous-silver ores. They occur in the oxidized portions of the silver deposits of the Western United States. Silver is very often associated with manganese oxides which in some ore deposits are dispersed through calcite, causing the black color of the host rock, which is known as black calcite. Black calcites can occur in carbonate rocks (10-1500oz Ag/ton) and in volcanic rocks (less than 1.0oz Ag/ton).

Jan 1, 1986

By M. I. Dobrynina

At the beginning of the 80-s the first diamond pipe in the East-European platform was discovered in the North of the Russian Federation on the White Sea Winter coast. During several years while studying this unique area data on kimberlites and country rocks petrophysical characteristics have been collected. Considerable experience in geophysical methods when searching and exploring diamonds was accumulated, and various methods of geophysical data interpretation were used. It has been established from the analysis of geophysical data that diamond-bearing kimberlites are located in the most ancient and the most stable block of the East-European craton.

Jan 1, 1995

By Earle J. Klohn

INTRODUCTION The paper presents a broad overview of the geotechnical site studies required for siting uranium tailings dams. These studies, which are interdisciplinary in nature, touch upon such related fields as: hydrogeology, hydrology, and seismicity. Tailings dams are commonly used to develop tailings ponds for the storage of the waste products generated by mine milling operations. In the past, most tailings ponds have been developed either above ground on dry land, or in existing lakes. In the United States a majority of the uranium mines are located in arid or semi-arid regions and past practice has been to store the wastes above ground on dry land (1,2). Currently, the United States Nuclear Regulatory Commission (N.R.C.) recommends below ground disposal of uranium waste products, although they indicate that they will consider above ground alternatives (3). In Canada many of the existing uranium mines are located in a wet environment and past practice has been to use small lakes and depressions as tailings ponds (1,4). However, current practice in Canada leans towards above ground, dry-land storage (5,6,7), and the Atomic Energy Control Board (AECB) guidelines (5) indicate this to be the preferable method. In B.C., where a moratorium on uranium mining has been declared by the Provincial Government, there are no existing uranium tailings ponds. However, both the formerly proposed Birch Island and Blizzard uranium developments would have used dry land storage. Most of the existing non-uranium mill wastes in B.C. are stored behind tailings dams on dry land. The waste products delivered to the tailings pond comprise, the ground-up rock that remains after most of the uranium values have been removed and the excess chemicals used in the milling process. These waste products, which are called "tailings", are normally mixed with water to produce a slurry and then pumped to the tailings pond. Since the uranium recovered constitutes only a small percentage of the ore (usually less than 1%) (8), large quantities of waste rock and associated transportation water are discharged into the tailings impoundment area. Consequently, relatively large tailings pond areas are required for the uranium tailings. In recent years, major advances have been made in the design, construction, and operation of non-uranium tailings storage facilities (9,10,11,12,13,14, 15). These improvements have been based on combining the latest advances

Jan 1, 1980

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

By Frederick P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian Region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modelled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1979