Search Documents

By Trenton Cohen, Joseph McDivitt, Shimi Tzobery, Joseph Sinacori, Scott Zylstra

The 2-mile Beach Interceptor Sewer Tunnel was constructed in 1954 to then-current mining and construction standards. Due to its lifespan and deteriorating condition it is now being stabilized and rehabilitated using conventional excavation and ground support. At its southern end, below the prestigious Three Arch Bay community, the original tunnel alignment passes under a historic landslide where the tunnel was sand-backfilled and capped by bulkheads in 1957 due to severe and caving ground conditions. Video footage of the existing 21- inch clay pipe showed that the pipe is severely damaged, which could potentially cause a catastrophic pipeline failure and sewage spill into the Pacific Ocean. This paper summarizes the thorough investigation and design process, tunnel realignment construction and monitoring, and the notable cooperation between all parties to overcome the project risks.

Dec 1, 2022

By Thomas P. Oxford

The impact of recent legislation on Florida phosphate industry operations has been dramatic. The most significant influences are described: the National Environmental Policy Act of 1969; the Federal Water Pollution Control Act Amendments of 1972; and implementation of the Florida Environmental Land and Water Management Act of 1972. Further discussion includes: critical examination of the recently completed EPA Areawide EIS; potential effects of the Resource Conservation and Recovery Act of 1976; the Surface Mining Control and Reclamation Act of 1977; current local and state laws; and summary of studies on radiochemical effects of mining, seepage from gypsum ponds, and dewatering of waste clays.

Jan 1, 1979

By T. Krichler

"Current mine control stations are either single-position systems with high engineering effort or all-in-a-box solutions with low integration possibilities of third-party devices. Above all, both approaches are cost-intensive and not feasible for small companies. This paper shall be an inspiration of how to enhance the productivity and monitoring of an existing mining system in a modular way by introducing a proven technique of the ongoing digital revolution: A Wi-Fi network based on the communication protocol OPC UA. The starter kit consists of a single-board computer, a WLAN access point and any electronic sensor. INTRODUCTION The majority of the European mining industry is run by small and medium deposits (Europe Geology, 2017). This is due to the fact that most ore mines in Europe are widely distributed within the continent, are generally small and additionally they are often steeply inclined. Such ore bodies are normally mined with underground mining methods and must be excavated with high selectivity because of their small thickness. That is why the economy of scales, higher efficiency through bigger machines, cannot be used in most deposits in Europe except for lignite mines. It is important to find an alternative possibility to improve the efficiency of European mines for making them competitive internationally. For cost optimization and profit maximization it is necessary to use the trends of industry 4.0 and to broadcast these into the mining industry to reach a technological advantage. The goals of the EU within the Horizon 2020 funded project are to shorten the actualisation of the mine and block model to hours, improve the communication with Through the Earth (TTE) via very- or ultra-low frequency for long-time monitoring of the abandoned workings, and develop a cost-effective mine control station for optimization of mining processes in Small and Medium Enterprises (SMEs) as well. This paper deals specifically with the new approach for data acquisition, transmission and visualisation of a mine. SCADA AND ERP IN MINING There are already many Supervisory Control and Data Acquisition (SCADA) and Enterprise Resource Planning (ERP) programs on the market, but these are normally not developed for the mining industry. At the moment this leads to three options. • To hire a system integrator, who shall build a complete control station for one mine that requires a high amount of knowledge in programming and cannot be maintained by the mining company itself. • To buy different types of out-of-the-box systems, whereby every system can include some of the used technology. In this case a huge amount of project engineers and operators – at least one per system and shift- is required. • To buy every machine and program from one company including the service contracts."

Jan 1, 2018

By Pat DeWilliam

The Yakobi nickel-copper deposit is located essentially at tidewater in the east-central part of Yakobi Island, about 16 1 airline km (100 airline miles) west of Juneau, and can be reached by float plane and boat from Juneau and Sitka. The fishing village of Pelican, population 400, is situated 14.5 km (9 miles) to the east. An unimproved road, approximately 4 km (2.5 miles) long, connects a dock site at Lisianski Strait with the main part of the deposit known as the Basin Area (Fig. I). Other mineral occurrences are known as the Takanis, Flapjack, and Beach Areas. Another smaller nickel-copper deposit is located about 32 km (20 miles) to the south on Western Chichagof Island and is known as the Mirror Harbor nickel-copper deposit. The original discovery of the Yakobi deposit was made by S.H.P. Vevelstad about 1920 and a 47.5-m (156-ft) long adit was driven on the southwest side of the deposit in the Basin Area. The deposit was examined by J.R. Van Fleet of Union Carbide in 1930 and by J.G. Fairchild in September 1931. Stanley and Yates of the International Nickel Co. of Canada (Inco) visited the property in August or September 1937. In 1942, the controlling interest in the deposit, covered by 124 unpatented claims, was said to be held by Vevelstad and associates

Jan 1, 1991

By John E. Anderson, Charles A. III Cravotta, Eleanora I. Robbins, E. Terrance Slonecker, Gordon L. Nord

Remote sensing is being tested for its ability to identify the severity of impact on streams that are subjected to contaminated mine drainage (CMD) in the Southern Anthracite Coalfield of Pennsylvania. Airborne digital multispectral video images of acidic and near-neutral CMD are being compared with field spectra, water chemistry, mineralogy, and microbiology. Spectral differences in the visible region of the electromagnetic spectrum are caused by the presence of schwertmannite in the acidic precipitates and ferrihydrite in the near- neutral precipitates. The acidic CMD averages 1,500 mg/L sulfate and has bacteria coated with schwertmannite; the near-neutral CMD averages 87 mg/L sulfate and has bacteria coated with ferrihydrite.

Jan 1, 2000

By J. D. Miller

The effects of operating variables on water transport to the over- flow, classification of hydrophilic particles and the recovery of copper and molybdenum from a low-grade porphyry ore are presented. Recoveries of copper and molybdenum exceeding 90 percent at a grade of 8 percent Cu and 0.2 percent Mo were realized for minus 100 mesh (1 49 µm) material at retention times of less than 500 milliseconds. The rapid rate of flotation and the effective separation of fine particles for an air sparged hydrocyclone appear to be due to directed interaction of particles in a high force field with numerous freshly formed small bubbles. This interaction occurs in the swirl flow developed by the system and is analyzed in terms of collision and induction time phenomena.

Jan 1, 1982

By Panshi Xie, Yan Chen, Shaogang Wu, Yang Hang

In order to realize the intelligent mining of coal seam with large dip Angle, this paper adopts the methods of large proportion variable Angle loading threedimensional physical simulation experiment, numerical simulation and field measurement with digital twin technology. The hydraulic support with large dip Angle and large mining height is used as the prototype to design the physical entity model of 1:5 hydraulic support, combined with modeling and graphics rendering technology. Angle, displacement and load sensors were selected and placed to realize the data channel between the lower machine and the upper computer of the digital twin system, so that the position and load data of the physical entity model and the twin model of the laboratory hydraulic support could be shared in real time. Moreover, the multi-dimensional dynamic and static load transfer law and the position evolution characteristics of the support and surrounding rock under different inclination angles were analyzed. The results show that: with the increase of the Angle of the working face, first, the initial support force required by the support decreases, and the damage degree of the roof increases; When the roof is soft, the lifting operation can avoid the instability of the support to a certain extent. Second, under the action of positive pressure, the load of the top beam under different angles is balanced; Under the backpushing action, the load in the upper inclined area of the shield beam increases gradually, while the load in the lower inclined area decreases gradually. Under the lateral push, the load changes periodically, and the load in each cycle is increased compared with that in the previous cycle. Third, the numerical simulation analysis shows that the load on the lower bracket is less than that on the upper bracket, and the load on the bottom of all the columns is greater than that on the middle and upper brackets. In order to reduce the impact of the columns on the bottom plate or the base, it is necessary to improve the anti-subsidence ability of the base. Finally, according to the research results, the improvement and optimization measures of the support are put forward, and the field test shows that these measures effectively solve the problems of sinking, sliding and tipping of the support in the working face with large inclination Angle, and obtain good application results.

Feb 1, 2024

To maintain its brand position in the competitive market of mining equipment, the Volvo Construction Equipment (Volvo CE) engineers were challenged to develop top-performing wheel loaders and articulated haulers even faster than before. To start, this meant reducing prototype test cycles by two-thirds. The final goal? Chopping in half the virtual prototyping time in early design phases. Creating a unified co-simulation solution In this ground-breaking project, the Volvo Construction Equipment design team in Eskilstuna, Sweden, replaced its piecemeal department-by-department process with a single solution based on LMS Imagine.Lab AMESim. With one unified model, they could simulate the behavior of four major vehicle subsystems in wheel loaders and articulated haulers: hydraulics, powertrain, thermal management and the actual driver. Subsystem models exchanged data seamlessly.

Jan 1, 2011

By V. Prabhu, D. Mantha, R. Reddy

Secondary copper blast furnace slag was treated with carbon to derive the conditions for maximum recovery of copper with a minimum simultaneous reduction of iron oxide. Experiments were carried out to study the effect of temperature, carbon and CaO additions to the slag on the efficient recovery of copper. A two-stage reduction process was also employed to study the efficiency of copper recovery and the results were compared with those of single-stage reduction. The maximum recovery of copper in alloy phase was obtained with 5 % initial carbon in the slag, 2% CaO addition to the slag and at a reducing temperature of 1573 K. Higher grade of the alloy phase with respect to copper was obtained by employing a two-stage reduction process. The results obtained in this study are comparable to those of the earlier research on the recovery of copper from reverberatory furnace discard slags.

Jan 1, 2004

By N. B. Aughenbaugh

A study was made to determine those petrographic parameters that are correlative with carbonate-aggregate quality as indicated by the Los Angeles abrasion and absorption tests. Samples collected at 28 sites in northern and eastern Indiana were analyzed petrographically, chiefly for void content, grain size, grain-size variation, grain shape, and grain interlock. Most of the sampled sites are in the belt of Silurian rocks of east-central and north- western Indiana. Though a few sites lie outside this belt, most of these have only a thin Devonian section above the Silurian. Three sites are non-Silurian and are included for comparison. Most of the samples studied are from Middle and Upper Silurian units. Both biohermal and nonbiohermal facies are included. The biohermal rocks are typically dense but vugular, finely crystalline granular dolomite. Nonbiohermal facies are porous, medium to coarsely crystalline, granular dolomite with dolomite rhombs The Los Angeles abrasion losses ranged from 20 to 46 per cent, the rocks in the eastern part of the state showing the higher values. Absorption tests indicate the same general quality trend. Comparison of petrographic studies with Los Angeles abrasion- and absorption-test results indicate the following correlations. (1) As per, cent of voids increases, quality decreases. (2) As average grain size increases, quality decreases. (3) Variations from mean grain size appear to have no effect on the quality. (4) As angularity and roughness of the grains increase, quality increases. (5) As grain-to-grain interlock increases, quality increases. Variations in the calcium-magnesium ratio have no apparent effect on aggregate quality, except as they affect the texture.

Jan 1, 1966

The Bureau of Mines, U.S. Department of Interior, is currently investigating strata interactions associated with the mining of multiple coalbeds. Strata interactions due to subsidence are a result of undermining. This study involves underground investigations at a mine where room and pillar panels are actively being developed through an area of the Sewickley Coalbed which was subsided by undermining of the Pittsburgh Coalbed. Research to date indicates that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. Consequently, this has led to major roof falls in the active panels, resulting in considerable production delays and supplemental roof support costs.

Jan 1, 1985

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

 The paper combines theoretical and experimental analysis to improve the accuracy of predicting paste yield stress by slump flow. It derives an analytical model of slump flow for yield stress, providing a theoretical basis for quantifying the rheological properties of paste with slump flow. The study uses three different tailings-prepared pastes and constructs an empirical yield stress model, showing high accuracy and good generality.

Aug 1, 2023

By Michael Wortley

Metso?s Process Technology and Innovation group is a world leader in mineral processing consulting. A significant amount of this consulting work involves process integration and optimization (PIO) studies, which include investigating the effects of drill-and-blast design and implementation on downstream processing. Critical to these studies is the ability to track specific ore into, and through, the plant. To increase the accuracy of this ore tracking, Metso Process Technology and Innovation (PTI) developed a system to track ore using a radio frequency identification (RFID) transponders technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and, finally, into the concentrator. The system is called SmartTag. Since its commercialization in 2007, SmartTag has been used in the majority of PTI?s consulting projects, and several permanent systems have been installed worldwide.

Jan 1, 2012

By J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) which is designed to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later will semi-automate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide real-time or near-real-time information about the performance of the loading and hauling units to the section foreman, allowing him to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and the first phase is scheduled for in-mine testing within the next year.

Jan 1, 1991

By P. M. Brown

The Bureau of Mines, U. S. Department of the Interior, has developed a method of dewatering clay slurries based on flocculation by high-molecular-weight polymers and water removal from the formed flocs using a trommel or hydrosieve. The exchange ion on the clays affects their dewaterability. Metal ions in solution and on the exchange sites of smectite clays are known to act as Lewis acids. Recent work has determined that these ions can be titrated with high-molecular-weight polymers. The relative acidity of the exchange ion and the basicity of the polymer determined by the new method give insight into the dewatering mechanism.

Jan 1, 1988

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

By D. S. Choi

The paper contains a subsidence measurement taken over a room and pillar panel of a mine located in northern West Virginia. A total of 72 monuments were used to determine a three dimensional view of mine subsidence. In addition, the results of measurements were used to compute ground strains with the use of a numerical model.

Jan 1, 1982

By C. C. Harvey

Asia is experiencing a growth market for industrial kaolins for use in ceramics, paper, plastics and other market sectors. Export and import data for the Asian countries reflects this growth with the Peoples Republic of China as the major exporter of clays and Japan the major importer. The growth in tonnage and product sophistication of kaolins produced on Belitung in Indonesia is typical of developments that are taking place in many locations in Asia. This region therefore presents opportunities for mineral processors and a challenge for the exploration geologist, the mineral processing engineer, the mineral economist and the marketing specialist.

Jan 1, 1996

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By Bo Arvidson

SALA MAGNETICS, INC. is now operating a 15 tph continuous high gradient magnetic separator, the SALA-HGMS® Mark III Carousel, as part of a complete mineral processing pilot plant installed at Sala's Cambridge headquarters. The Mark III can generate a maximum magnetic field of 18 kG making it possible to process even weakly magnetic, finely ground ores and ore tailings on a continuous basis at the performance level achieved in Sala's cyclic high gradient magnetic separators. Test results on iron ores, clay, and decoppering of molybdenum concentrate will be discussed. Bench scale tests have been performed on all of these materials using the SALA-HGMS® Model 10-15-20 Cyclic Magnetic Separator. A direct correlation may be made between cyclic and carousel results. Sala's Mark III Carousel high gradient magnetic separator is designed to permit scale-up to machines capable of processing two hundred (200) tons of ore per hour and more.

Jan 1, 1976