Search Documents

By Joseph W. Murray

GENERAL DESCRIPTION The undercut-and-fill method of mining was devel¬oped by Inco Ltd. in the Sudbury district of Ontario, Canada, to deal with abnormal ground conditions en¬countered in pillar recovery. Although it is now some¬times utilized as a primary stoping method, the main application continues to be in pillar recovery. In any mining method in which fill is employed, pillar systems tend to fail gradually as stoping pro¬gresses. As a result, most pillars are completely destressed and broken by the time pillar recovery com¬mences. Control of the back in such ground becomes a major problem and is contingent on local conditions as they exist in the workplace. In most mining methods, operations such as drilling, blasting, slushing, and tim¬bering can be readily assessed and the mining cycle pre¬dicted. However, in the mining of pillars with overhand methods, the time and effort required to maintain a safe back varies to a quite unpredictable extent. For years the square-set method was the most effective means available for pillar recovery. However, in areas where bad ground was encountered, square setting was a costly and sometimes hazardous method. As the tonnage mined from pillars increased, it was apparent that a safer and less expensive approach was required. Past experience indicated that the best way to deal with broken ground was to mine from the top down. Top slicing systems were examined but were rejected due to the major sub¬sidence which resulted. However, ideas generated from studying top slicing finally developed into the present method of undercut-and-fill. This method, which has almost completely replaced square-set mining, exhibits reduced costs, has improved safety and efficiency, elimi¬nates the factor of bad ground overhead, and allows a closer prediction of the actual mining cycle. The result is more accurate scheduling of pillar production. This factor is of increasing importance as the tonnage from pillar recovery increases in relation to total mine pro¬duction. Undercut-and-fill is a method of extracting a block of ore by mining successive cuts, working from the top down. After a cut of ore is completely mined out, lami¬nated timber stringers are constructed along the sides for the full length of the cut. Round logs covered by a wire screen are laid across the stringers to form a mat. The cut is then tightly filled with hydraulically placed cemented sand fill. Mining is then resumed on the cut immediately below the mat. As the cut advances, the timber stringers are supported by round timber posts seated on the solid bottom of the cut. Drilling, blasting, muck removal, and timbering operations are repeated until all the ore in the cut has been removed. At this time, another log mat is laid and the cut is filled. This sequence is continued until the block has been mined from level to level. The basic principles of undercut-and-fill can be adapted to a variety of mining situations. It can be applied transversely or longitudinally in ore bodies of varying width, that dip from vertical to flat lying. The method can be applied using conventional equipment or it can be mechanized through the introduction of small diesel or air-powered units for muck removal. Undercut¬and-fill is a selective method, ore recovery is high, and dilution can be controlled to an acceptable level. How¬ever, it is a high-cost, labor-intensive method and as such its use is restricted to areas where the less costly meth¬ods of ground support are not successful or where bulk mining methods are not adaptable. One basic require¬ment for undercut-and-fill is an adequate source of hydraulically placed cemented sand fill and a dependable sand plant and distribution system. The success of the undercut method is to a large degree dependent on the competence of the fill placed in each of the successive cuts. In theory, the weight of the fill on each cut is supported in part by the cemented sand itself as it binds to the rough sides of the mined¬out areas next to the pillar walls, and in part by the tim¬ber support. As mining progresses beneath the mat, a downward pressure is exerted within the cemented fill and a voussoir arch develops above the mat, across the full width of the cut. This supports the major portion of the load. The log mat and posts have a double func¬tion in that they carry the remaining weight not sup¬ported by the voussoir arch and in addition prevent any pronounced settling of the fill mass. Excessive settling breaks the bond between the cemented fill and the pillar walls, eliminating the arch effect and transferring the entire load to the mat and posts. The theory of a voussoir arch forming within the cemented sand fill mass is substantiated in practice by the fact that pillars have been mined from level to level with no more significant weight on the bottom cuts than was experienced on the top cuts. In effect, as mining progresses downward, there is no additional transfer of weight from previous cuts to the cut being mined. APPLICATION OF UNDERCUT-AND-FILL Because of their size, the Sudbury ore bodies are, for the most part, mined transversely and, to a considerable extent, by filling methods. Transverse stoping blocks are designed with 9-m (30-ft) crown pillars established be¬low each level and with stopes separated by vertical rib pillars. In past years, floor pillars were left above the level as well, but present practice favors the silling of primary stopes at the base of the rail. Rib pillars are designed to meet the ground control requirements of the primary stoping methods. Local conditions and past experience generally dictate their size. Historically, since the square-set method was to be used for recovery, rib pillars were designed to accommo¬date standard 1.7-m (5'h-ft) sets. A typical rib pillar is four sets wide [6.7 m (22 ft)] when located between two square-set or cut-and-fill stopes having a width of 8.4 m (27.5 ft). When the undercut-and-fill method was de¬veloped, a mat width of two sets was adopted. This di¬vided each cut of the common four-set pillar into two

Jan 1, 1982

By Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducrng bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the porosities of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also extended a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore modes. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of the first of June 1984, a total of 29.4 million long tons of sulphur had been produced west of the Pecos -aver. Duval produced more than 88 percent of that total.

Jan 1, 1984

By Laurence B. James

The California Department of Water Resources is concerned with the development, distribution, and protection of the State's water resources. Geologic activities of the Department relate to planning, construction, and operation of water projects, supervision of the safety of over 900 dams under state jurisdiction, and investigation and control of ground water supply. The Department is engineering oriented, and the role of the geologist is to assist with the solution of engineering problems. Some of these problems require the integration of many talents, including not only those of geologists and engineers, but also those of economists, lawyers, seismologists, chemists, geophysicists, and hydrologists, Frequently, a task force of several disciplines will attack a problem as a team.

Jan 1, 1965

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

Rutile ore is an important resource for the production of titanium products, and flotation is an efficient method to enrich rutile from its deposits. Motivated by strong commercial demand for titanium metal and alloys, substantial efforts have been made to improve the flotation efficiency of rutile. Styryl phosphonic acid (SPA) and salicyl hydroxamic acid (SHA) are commonly used as collectors for rutile flotation, and lead (Pb) ions can be used as activators for rutile flotation with SPA or SHA. Xanthates have a price advantage over SPA and SHA for the flotation of sulfides as SPA and SHA prices are higher than xanthate prices. In this work, we found that when rutile is activated by lead ions, amyl xanthate is an efficient collector for rutile flotation at pH 8. A slightly basic slurry can be readily obtained. Moreover, the price of amyl xanthate is lower than that of SPA or SHA. In this regard, this flotation strategy has the potential to be used in industry. Furthermore, the adsorption features of amyl xanthate on the Pb-activated rutile surface was investigated by experimental methods, which provides insight into the role of lead ions in rutile flotation.

Paper and paperboard manufacturers need to quantify the carbon footprint and environmental impact of their products to satisfy market, social and government demands. Coated paper products contain minerals, such as kaolin and calcium carbonate, at significant levels; some coated paper grades have mineral contents as high as 45% by weight. Some uncoated paper has no mineral content, but most uncoated paper contains some mineral to improve appearance, process efficiency and cost. Super-calendared paper grades can contain levels of mineral up to 35% by weight. This paper describes how to calculate the carbon footprint of kaolin and calcium carbonate minerals used for white pigments. The carbon footprint of these minerals strongly correlates to the primary energy sources, final product form and energy used to calcine kaolin and lime. Kaolin and calcium carbonate pigments have a favorable impact on the carbon footprint of paper and paperboard products by directly substituting for fiber and by reducing the energy needed for paper making. Key words: Kaolin, Calcium carbonate, Paper production, Carbon footprint, Lifecycle analysis

Jan 1, 2010

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By P. James, L. J. Steiner, F. Turin

NIOSH researchers and an industry partner conducted an investigation to study the effectiveness of ergonomic interventions in mining. The study required a significant commitment of time and resources from the cooperating site, Bridger Coal Company. This paper focuses on some of the challenges faced by the researchers and their cooperator. Challenges included the need to redesign methods of identifying and prioritizing injuries, and the need to train the workforce in ergonomics while still maintaining progress and interest in the process. The authors discuss some practical interventions implemented by Bridger Coal to date, and discuss future research implications brought about by PacifiCorp’s Generation Business Unit, who monitored the project to determine whether an employee-owned ergonomic process could be implemented throughout their operations.

Jan 1, 2003

By Jr. Wallace

This paper describes the importance of mine ventilation and air conditioning in the operation of a nuclear waste repository. It discusses the impact of ventilation on determining the number and size of shafts and access drifts to and within a repository horizon. The paper also describes the need to maintain separate ventilation systems for waste emplacement and construction operations. The requirement to have filtration capabilities for exhaust air from waste emplacement areas is discussed. Because radioactive high level waste will induce high temperatures in the emplacement drifts, the ability to cool an emplacement drift for re-entry requirements is important. The paper discusses strategies to cool an emplacement drift and the possibility of using continuous airflow to control temperatures in these drifts.

Jan 1, 1991

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By Joseph B. Gillenwater

Miss Gertrude Carey lived next to us in Martinsburg, West Virginia for several years. She was a retired school teacher. She was also a cousin to Messers Dan and Joe Baker who owned and operated Standard Lime and Stone Company, a predecessor of Martin Marietta Corporation. She-was well acquainted with the Baker family and their history. Here is one of the legends she told my wife, Jean, and me. The Bakers were originally Tanners. They had a tannery near Frederick, Maryland. There were several boys in the family and when they were grown each man had specified responsibilities. Will Baker was assigned the duty of locating, buying, and transporting tanbark and lime. As he traveled through Maryland, Virginia, Pennsylvania, and West Virginia to locate and buy tanbark, he also talked the farmers out of some pieces of lime, which the farmers had produced in holes dug and filled with layers of limestone and wood. Will Baker took the lime and soaked a piece of hide in the milk of lime. If the lime did not spot the hide, Will Baker would get the farmer to burn some lime for him, and further tests would be made. If these tests were good - the Bakers bought the land. They eventually discovered that the limestone that would make lime that wouldn't spot the hide would also be suitable for producing steel. They began producing lime just outside Harpers Ferry, West Virginia in pots and upright kilns. That stone too small for the kilns was just perfect for railroad ballast. Now you know how "Baltimore Blue Bloods" got together!!

Jan 1, 1979

By William G. Wilson

In the U.S. today a number of tentative synthetic fuel plants have been sited by a number of major corporations. Each of these for a number of reasons have deferred construction. The only synthetic fuel plants under active development are those being built with the Energy Research and Development Administration (ERDA) under the authority of the Non-nuclear Energy Research and Development Act of 1974 (Public Law 93-577). Under this Act in joint sponsorship with industry, a series of coal conversion pilot and demonstration plants are being built to produce environmentally acceptable fuels from high sulfur coals. Before entering into a discussion of the factors associated with the siting of the ERDA coal conversion program, the difference between a pilot plant and a demonstration plant should be explained. The terms pilot plant and demonstration plant iridicate a size of plant rahter than technology. A pilot plant will vary from an "add-on" to an existing facility to an independent unit. Demonstration plants are a wholly independent, self contained plants, capable of independent operation to demonstrate the environmenta1, economic, and technica1 feasibility of a technology. These plants are from one-third to one-tenth the scale of a commercial operation and often described as plus 1000 tons per day of coal consumption. Their purpose is stated in the Act (Section 6, (3)(E),) "to accelerate the commercial demonstration of technologies for producing syncrude and liquid petroleum products from coal: Provided. That the Administrator shall invite and consider proposals from potential participants based upon Federal assistants and participation through guaranteed prices or purchase of the products .... " In site selection and plant design it has been suggested that special interest groups should be allowed to dictate the site and specify the design. Under the present program the industrial partner who is contributing 50 percent

Jan 1, 1977

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By L. A. Wasselle

The Israel Mining Industries Institute for Research and Development has developed, during recent years, a number of new processes for fertilizer materials. Their phosphoric acid processes, however, are capable of producing an acid of far higher quality than that normally associated with fertilizer grade acid. This paper will discuss two of these processes showing the quality attainable and the capital and operating costs for, U. S. conditions. The Standard IMI Process is based on the acidulation of phosphate rock with hydrochloric acid and involves solvent extraction for the separation of high quality, phosphoric acid from the resulting solution. The IMI Purification Process applies the same solvent extraction technique to the purification of a wet process phosphoric acid from sulfuric acidulated rock. IMI has built and operated a semi-works scale demonstration plant for the standard process. The first commercial plant was started up in; Japan in 1962. This small seven metric ton per day plant is currently producing a furnace quality acid. A larger 50 metric ton per day plant is nearing completion in Brazil. Another 50 metric ton per day plant is under design while a large plant with a capacity in excess of 150 metric ton per day is in the planning stage. Both of the latter facilities are for Israel.

Jan 1, 1966

By William H. Dresher

A recent report to President Reagan from the Business-Higher Education Forum, entitled, "America's Competitive Challenge: Need for a National Response," (1) observes that in the recent past, ". . . much of that research, which is necessary for major breakthroughs and sustained productivity improvements, was redirected to short-term objectives ... At the same time, American universities, which conduct more than half of the nation's basic research, have suffered from an accumulated under-investment in facilities and equipment amounting to an estimated $1-4 billion." Also contributing to the decline in America's productivity, the report said, are "...weak technology transfers between government and industry and between universities and industry..." This report as well as other recent reports and articles have, reopened a subject which has long been debated but rarely resolved-- the interaction between the academic community and industry in the sponsorship and conduct of research. The subject is unfortunately, too often treated as a controversial issue involving ethics and the profit motive when, in fact, the two branches of society -- industry and academia -- are necessarily part of the same system. I would like to speak to you today on the subject of university-industry interactions and to some extent discuss the role of government in such interactions. Finally, I will make some remarks as to how this subject applies to the mining industry.

Jan 1, 1984

By J. R. Evans

In order to patent an industrial mineral placer mining claim, it must incorporate an economic deposit. Each ten acre parcel is evaluated for its mineral -in -character nature. Nonmineral -in -character parcels cannot be patented. Economic concerns include: claim locations, dummy locators, common variety nature, "excess reserves," and environmental constraints. Also, geologic and mineralogic studies, sampling and testing procedures are vital. Mining, milling, processing cost, and taxes must be evaluated. Product marketability analysis is necessary before starting any cash flow or discounted cash flow study. Valid data is essential to evaluate an economic industrial mineral deposit.

Jan 1, 1997

By Faruk Oksuz, Clay Haynes, David Egger

The United States Army Corps of Engineers (USACE) has committed to solve a major drainage problem in the suburban Chicago community of Griffith, Indiana. The Cady Marsh Ditch is currently undersized and on occasion spills its banks causing flooding and economic setbacks to the community. Preliminary studies have identified both tunnel and surface solutions as being attractive and viable. The USACE has decided that this project is an opportunity to use the design-build contracting approach to maximize ingenuity in project approach and to allow the market to dictate whether a surface or subsurface solution is most attractive. The tunnel would be over one-mile in length through sands, gravels and clay. Water control will be an issue during tunneling. The paper will explore the contracting approach to the project and the adaptation of Underground Technology Research Council (UTRC) guidelines for underground contracting to a design build project. The roles of Owner, Owner’s consultant, and design-build contractor will be defined as interpreted by the USACE and key contract provisions will be described and contrasted with a traditional design-bid-build approach to tunnel construction.

Jan 1, 2003

By D. Brabec

One of the analytical problems in exploration geochemistry is the choice of a method of sample attack which would be rapid, simple and reliable in terms of precision and discrimination between different concentration levels of elements sought. The wet sample attacks currently used in analysis of silicate rocks vary from total decomposition to leaching by weak extractants. The total decomposition of such materials is usually achieved either by alkaline fusion or hydrofluoric acid attack. The first method requires the use of platinum vessels which is both expensive and slow for batch operation. The second type of attack is more widely applied in rock geochemistry1, but it is still relatively slow for exploration purposes and requires extra care (especially when hydrofluoric acid is used in mixture with perchloric acid). Considerable improvement in speed can be achieved by using the sample attacks which release only part of the metal present in a rock.2,4 One of such attacks is the leaching of pulverized rocks by hot aqua regia.3 Another technique widely used in geochemical prospecting involves fusion of the samples with potassium pyrosulfate (or bisulfate) followed by an acid leach of the malt .5 One of the advantages of these techniques is the use of glassware in decomposition stage which considerably increases the analytical productivity. It should be noted that partial chemical attacks tend to extract from a rock mainly the non-silicate metal which may give results more significant for exploration purposes than the analysis for total metal.

Jan 1, 1970

By H. M. Park

Risk is a major factor in all mining activities, arising from many internal and external variables. The authors? research has resulted in a systematic method for the quantification of risk in mining projects (Park, 2012), and this research is being presented in a series of papers. The first paper (Park and Nelson, 2013a) identified the variables associated with risk in mining projects, and their effects and was published in the October issue of Mining Engineering magazine. The second (Park and Nelson, 2013b) discussed methods of assessing the overall risk associated with those variables (published at www.me.smenet.org), and presented a statistical model based on a survey of 31 experts. This paper will present an evaluation of the statistical model, using data from previous mining investment decisions in which the authors have been involved.

Oct 1, 2013

The purpose of this paper is to demonstrate how the Computational Fluid Dynamics (CFD) technique can be an attractive approach to evaluate the performance of face ventilation systems. To present the capability of the CFD for such a study and for design purposes, a series of simulations using CFD have been performed at the Department of Mining Engineering, University of Kentucky, for different face ventilation arrangements (e.g. different scrubber geometries, brattice (curtain) and continuous miners locations, airflow quantities, etc.). Results from these simulations are displayed as three dimensional graphs and discussed. Needs for the field validation of these results and refinements of design methodologies are also discussed.

Jan 1, 1998