Search Documents

Refractory gold concentrates often contain sub-microscopic gold that is encapsulated within the crystal matrix of iron sulphide minerals such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically, by oxidative processes such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pre-treatment processes is usually the oxidation of the sulphides to elemental sulphur, sulphur dioxide gas or sulphate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as down stream operating costs. Iron sulphide minerals break down completely during pressure oxidation, and dissolve in the sulphuric acid solution that is generated from oxidation of the sulphides. This liberates the tiny gold particles that were originally trapped in the sulphide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulphate, but this is rapidly oxidized to ferric sulphate, which then hydrolyzes and re-precipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200OC) the formation of hematite is favoured. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200OC), the formation of basic iron sulphate is favoured. If the ore or the leach solution contain significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favoured. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulphate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulphates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulphate; the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant, and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

By John Barakso

The Sam Goosly or Equity silver deposit is fundamental- ly a discovery based on the analysis and interpretation of reconnaissance geochemical samples. The discovery was made by Kennco in an area of heavy forestation and wide- spread cover by thin glacial debris. No major mines had been discovered in the vicinity of the discovery prior to the geochemical reconnaissance, and the interpretation of the geochemical results therefore was based on data available through geologic mapping and the sample collection process. In the period 1959-1961, PE. Hirst and his crew, in 1962- 1965 P.T. Blackand his crew, and in 1966-1967 C.S. Ney and P.T. Black and their crew collected geochemical samples from the area of what is now the ore body. Several of these samples were compiled and reanalyzed in the winter of 1966- 1967 for various trace elements, including fluorine. A strong, almost 16-sq-km (10-sq-mile) fluorine anomaly was projected along with a very weak heavy metal anomaly. On the basis of this anomaly, a chalcopyrite-bearing quartz monzonite was discovered in 1967. This was a misleading, noneconomic discovery not associated with the Sam Goosly discovery. The interpretation of the geochemical data by Barakso that summer indicated that another source was responsible for the fluorine anomaly. The conclusion was based on the assemblage of trace elements. Therefore C.S. Ney recommended further regional soil sampling to check the original data. The early results of this follow-up sampling found over 33 ppm silver. First float, then ore outcrop was found in the area of the silver anomaly. The attached reprints complete the development of the property after the discovery of the outcrop of ore.

Jan 1, 1990

By Roger Storry, Arnaud Hochart, David Harris, Olivier Martin

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands under the main shipping channel in Biscayne Bay. Five cross passages (CPs), spaced at 200m centre to centre, provide emergency access between the two tunnels, as shown in Figure 1.The CPs were constructed by open-face excavation methods but the particular geological conditions at the project site (loose and variable carbonate sedimentary strata with very high permeability) required specific ground treatment solutions to provide safe excavation conditions and to ensure the long term serviceability of the permanent works construction. Where access allowed, ground treatment was performed from the ground surface using deep-mixing techniques; however, at two locations (CP2 and CP3) surface access was restricted and ground treatment by freezing, performed from the tunnels, was required. The CPs are 12.3m long with an excavation diameter of 5.8m and are located up to 30m below the water table partly or wholly within the Key Largo limestone (termed Layer S7 in the ground model). Layer S7 is a coralline limestone having a metastable honeycomb structure and high variable porosity. At CP2 the upper portion of the excavation was within the overlying Anastasia Formation limestone (Layer S6), comprising a highly permeable coquina. The geological profile along the project is shown in Figure 2.This paper presents aspects of the freeze design and the risk mitigation necessary to successfully achieve the construction of the CPs in the unique geological conditions."

Jan 1, 2016

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010

By Martin B. Treuhaft

Expectations for coal in the early to mid-1970&apos;s prompted the government and industry to pursue research and development programs to increase underground and surface mining coal productivity and net coal recovery. Several programs concerned advanced surface mining methods for thin seam coal recovery. Three such programs, along with related areas of interest, are presented in this paper, namely: (1) extended depth augering for trench-strip applications; (2) high recovery auger heads for enhanced recovery; and (3) variable wall mining in low cover longwalls. Conceptual development is examined, prototype testing is discussed, and potential operations are considered.

Jan 1, 1983

By S. S. Pathak, S. Mishra, M. H. Tyeb, A. K. Majumder

Roping in hydrocyclones is a well-known phenomenon in mining and mineral industries which put serious restrictions on their continuous and maintenance free operation. Roping is mostly observed in association with high underflow solid concentrations which can be attributed to higher fraction of solids reporting to the underflow or the feed solid concentration itself being higher. This paper proposes a newly designed spigot with a truncated conical geometry which can allow for a rope-free discharge at higher feed solid concentrations. The experimental observations revealed that in the operation of a 50.8-mm-diameter hydrocyclone, roping ensued at 10% to 12.5% (wt%) feed solid concentration depending on feed inlet pressure for the cylindrical spigot, whereas with the modified spigot, rope free discharge was attained even at 25% (wt%) feed solid concentration.

Jan 8, 2022

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), we showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/t of REEs occur in AMD and AMDp, respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. 

By J. Y. Kim

Lead ions originating from galena during processing of complex sulphide ores migrate to "cover" the surface of sphalerite and iron sulphide mineral particles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead-activated minerals float in the Cu/Pb rougher circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead-activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide particles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.

Jan 1, 1995

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open pit and underground mines of all sizes are regularly collecting point cloud data as Laser Scanning (LiDAR) and Photogrammetry surveying devices have finally become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely (safely), rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing, so this paper specifically focuses on digital outcrop modeling and digital terrain engineering. INTRODUCTION Point Clouds The high-resolution and increasing availability of point cloud technology is rapidly improving open pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations, and typically the reflective intensity and/or the visible three-band color of each point (Figure 1). LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device. Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3-D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles, and even in a mobile backpack shown in Figure 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds”, but this paper does not address these due to their higher cost and lower versatility and mobility. Technology In the past few years point cloud acquisition device prices have dropped significantly, devices have become lighter, smaller and easier to operate, and processing and utilizing the data has also become faster and easier. Device size improvements include mobile backpacks (Figure 2) and handheld mobile LiDAR (CISRO, 2014), allowing mobile scanning in tight spaces both above and below ground or inside and outside of man-made structures. Airborne data acquisition options have expanded dramatically with the spread of UAS technology as seen in Figure 3 (Hexagon Geosystems, 2015). Once UAS usage regulations are sorted out, these versatile machines will be everywhere, offering high resolution coordinate scans, imagery and other remote sensing. While backpacks and handhelds allow access to tight quarters, UAS permit rapid data capture from narrow to broad areas with multiple perspectives reducing data “shadows.”"

Jan 1, 2016

By V. Gall

The three-dimensional finite element technique combined with the progressive failure approach was utilized to simulate stress distributions in a mine section which occur in response to a longwall mining operation. Due to the availability of the Cray supercomputer, a large-scale three-dimensional finite element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1990

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By P. A. Mingione

AEROPHINE® 3418A is a unique sulfide mineral promoter produced by Cyanamid, based on phosphine (PH3) chemistry. It has proven effective as a collector for the sulfide minerals of copper and particularly lead (galena), as well as for secondary gold and silver values. AEROPHINE 3418A has widest application as a Cu and/or Pb collector for complex ores of Cu-Zn and Pb-Zn, which frequently have significant quantities of associated precious metal values. Advantages shown in the use of AEROPHINE 3418A are improved selectivities against Zn-and Fe-sulfides, increased precious metals recoveries, reduced total collector consumptions for Cu and/or Pb flotation, and increased flotation kinetics leading to higher recoveries of these values. Operating plant, pilot plant and laboratory test data from treat-ing different ores are presented, demonstrating the advantages in use and preferred application of AEROPHINE 3418A.

Jan 1, 1991

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

By Richard E. Gray

Virtually all structures show some signs of distress due to deterioration of the building components, to changed loads, or to changed support conditions. Changed support conditions result from ground movements. In mining regions many cases of structural distress are attributed to mining without considering alternative causes. This is particularly true of coal mining since it occurs under extensive areas. Coal mining is estimated to have already undermined more than eight million acres and may eventually undermine 40 million acres in the United States (HRB Singer, Inc., 1977). Other nonmetal and metal underground mines impact much smaller areas. Although it is sometimes difficult, even with careful study, to identify the actual cause of damage, persons responsible for underground coal mining should at least be aware of possible causes of building stress other than mine subsidence. This paper presents information on distress to structures and briefly reviews a number of causes of ground movements other than subsidence: Mass movements, dissolution, erosion, frost action, shrinking and swelling, yield into excavations and compressibility

Jan 1, 1986

By Joseph M. Zigich

The Anaconda Minerals Company operates a molybdenite and copper producing mine and mill facility near Tonopah, Nevada. Included with the milling facility is a ferric chloride leach plant for removal of copper mineralization from the molybdenite concentrates. Discussed are the engineering and construction schedules associated with the leach plant. The chemistry associated with the process along with a description of the process flow, equipment, and operating parameters are contained in the paper.

Jan 1, 1983

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By James R. Aggson

This paper summarizes the research effort that was conducted as part of a cooperative agreement between the U.S. Bureau of Mines, Denver Mining Research Center and the Pittston Company. The objective of this investigation was to further the understanding of the floor heave ground control problems that have plagued underground mining of the Beckley coalbed in southern West Virginia. Floor heave is both economically and structurally undesirable. Floor heave is accompanied by a redistribution of stresses and loads that are associated with an underground opening. This redistribution of stresses may cause roof or pillar problems that otherwise would not have occurred. The floor heave that occurs in the Beckley coalbed is not cons1dered to be caused by "squeezing" or plastic flow of the materials involved. The "squeezing" type floor heave is normally associated with relatively weak floor members that contain significant amounts of clay mineralization. The floor members in the Beckley coalbed are competent, relatively strong materials which fail in a manner that can best be described by the term "buckling." This buckling-type failure is indirectly related to the time-dependent deformation properties of the materials involved, but is considered to be more of a slender column, or panel, type failure than a "squeeze" or "flow"-related failure. The Beckley coalbed has had a history of floor heave ground control problems. The Glen Rogers mine, which opened in the 1920&apos;s, experienced extensive floor heave. In a report dated April 1929, James P. Keatley of the West Virginia State Department of Mines described the floor heave in the Glen Rogers mine. Several observations listed in the Glen Rogers report that appear to be consistent with current observations follow: 1. Water plays no apparent part in the floor heave process. 2. No evidence of gas has been found in the floor. 3. The thickness of the overburden, which varies from 183 to 396 m (600 to 1300 ft), has no relationship to the floor heave. In the conclusions of the 1929 report on the Glen Rogers mine, Keatley states, "A statement in brief as to the cause (of floor heave) would lie that an undetermined natural condition doubtless augmented by former and present mining methods causes the bottom to heave." As this report will show, Mr. Keatley&apos;s insight into the problem was most accurate. The "undetermined natural condition" is the existence of a biaxial, horizontal, compressive stress field. This stress field is in excess of that which would be expected from gravity loading. This stress field and the material properties of the floor rock combine to cause the floor heave that has been experienced. The floor heave that occurs in the Beckley seam generally occurs as arching, with a tension fracture, near the center of the floor span or as a break near the rib followed by vertical deflection (of the floor) at the rib and sloping of the floor across the entry. Examples of the floor heave are shown in Figures 1 and 2. The two types of floor heave are merely different manifestations of the same basic failure mechanism. When the entries experiencing floor heave were identified on a map of the mine under investigation, it was apparent that there was a relationship between the floor heave and the direction of the entries. The main entries, which are used for ventilation and haulage, experienced the majority of the floor heave. This directional relationship suggested a directionally related loading mechanism, or more specifically, a biaxial, horizontal stress field that exceeds what would be expected by gravity loading. Since the main entries were oriented at a bearing of N25oW, it was hypothesized that the maximum compressive component of the horizontal stress field was at 90° to these entries or at a bearing of N65oE. An in Situ testing program was developed to test this hypothesis and investigate the floor heave problem.

Jan 1, 1978

By Thomas A. Morley

This paper deals with the minimization of ventilation costs for the controlled-flow mine ventilation network. Cost elements considered include the cost of power and the fixed cost of the fans. The problem is modeled in a mixed-integer programming format and solved via the branch and bound method. Computational experience with sample problems is discussed.

Jan 1, 1983