Search Documents

By Howard J. Haselhuhn

The effectiveness of selective flocculation and dispersion processes for the concentration of hematite ore are strongly dependent on the ionic content of the process water. It has been noticed that magnesium ions are more detrimental to iron recoveries during gravity separation and flotation processes than calcium. This phenomenon was studied by measuring the zeta potential of hematite ore at various concentrations of sodium, magnesium, calcium, strontium and barium at a pH of 11. Results show that zeta potential inverts from negative to positive at concentrations as low as 0.16 mM of magnesium ions in the solution. It takes a significantly higher concentration (1.25 mM) of calcium ions to achieve the same effect. This difference is attributed to the ability of magnesium ions to adsorb to all surface hydroxyl groups, whereas calcium, due to its larger size, can only adsorb to every third hydroxyl group. This hypothesis was confirmed by results similar to those seen with calcium when this test was repeated with strontium and barium ions. The tendency for calcium ions to adsorb to every third surface hydroxyl group causes higher concentrations of calcium to be less detrimental to hematite concentration processes than magnesium.

May 1, 2012

By J. J. McDougall

The Windy Craggy copper-cobalt-bearing massive sulfide lies in the Tatshenshini map area of northwestern British Columbia, where British Columbia joins Alaska and the Yukon. The area is covered with numerous glaciers and ice fields that mask geologic detail and hamper ground access. In 1957, Ventures Ltd., the predecessor of Falconbridge Ltd., undertook a reconnaissance of the area using a float-equipped Supercub. At that time, large lakes and glaciers were unnamed and little was known of the geology. The prospecting team was led by J.J. McDougall with Stan Bridcut as pilot-prospector. Prospecting was directed at the St. Elias Mountains between the rich Kennecott copper deposits to the northwest and the Maid of Erin silver-copper mine on the Haines Road, BC. Reconnaissance flying in 1957 and early 1958 eliminated vast segments of the Kennecott-Haines Road terrain as being too inaccessible for mining. In 1958, the Supercub landed at an unnamed lake and the terminal moraine of an unnamed 12.9-km (8-mile) long glacier was prospected. The lake was called Tats Lake and the glacier named Tats glacier (short for Tatshenshini). Float of sulfide was found in the moraine. Follow-up investigation along Tats glacier led to the discovery of several small sulfide deposits and these were staked. Prospecting active glaciers in this area can be complicated because of drainage capture by eroding valley glaciers. Glacier capture resulted in the float from one mineralized area being deposited at different times in three widely separated moraines. Float of the Windy Craggy deposit, therefore, occurs along the course of older glaciers and at the base of the currently active ones. The problem of sourcing caused much additional Supercub reconnaissance. It is interesting to note that about 40 geographic names were given various features in this unmapped portion of the St. Elias Range, and these names were ultimately officially adopted.

Jan 1, 1991

By Nelson R. Shaffer

Secondary minerals, amorphous materials, and biologic entities that form on building stone can cause aesthetically unflattering changes in color and may even result in stone decay. Techniques to determine causes of such changes generally have entailed destructive sampling and often required chemical, thin section, X-ray, or other relatively slow, expensive measurements. We have found that a rapid leach of in-place stone using small volumes (50-100 ml) of very pure distilled, deionized water provides recovery of sufficient dissolved material to help diagnose stone anomalies. Water is sprayed onto the stone and collected in a nonwetting plastic pan. Ion chromatograph analysis of waters thus collected from more than 160 sites showed wide variations in concentration of anions F, Cl, NO3, and SO4. Anion analyses were made in minutes for less than $20 per sample. Cations Ca, Mg, Fe, and Sr also were detected, and analyses might be used to determine mineral sources using equilibrium computer models. Solid particles filtered from the samples can be examined microscopically to provide further information about atmospheric agents affecting the stone. The collected water can even be evaporated to precipitate dissolved minerals. Chloride values in samples rinsed from stone ran as high as up to 17,000 ppm, nitrate to 100 ppm, and sulfate to 1,000 ppm. Limited data also indicate that measurable amounts of fluoride were found in some of the rinse waters. Chlorides were most abundant in areas where the stone has become dimpled or spalled. Nitrates were generally higher near ground level, and sulfate tended to be more abundant in samples taken from higher sites or from sheltered sites. Dark-stained limestone tended to yield less soluble material than clean-looking stone. Leachable elements were higher in samples from urban areas. Most of our data are from limestone buildings, but the technique works on other types of dimension stone, man-made construction materials, and even natural outcrops of rocks. Longitudinal studies show that soluble materials vary through time and are affected by climate. This rapid, in situ leach technique, although still being perfected, shows great promise in the diagnosis of stone alteration and in the evaluation of stone treatments because it is completely nondestructive.

Jan 1, 1999

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

By Danqing Gao, Brijes Mishra

Heterogeneity in rock formation affects both rock behavior and strength. Spatial variance of rock properties is an important characteristic of rock that addresses the heterogeneity of mechanical and physical properties and their effects on underground mining. Assessing spatial variance can be useful for locating potential difficult grounds and for performing reliability analysis in the mining support system. This study presents a spatially correlated, random model to investigate the influence of rock heterogeneity on rock strength and failure propagation. A random field database with specific spatial correlation was created for each physical-mechanical property using laboratory data and the extreme value stochastic model in MATLAB. Based on the improved microscale random model, we considered one three-dimensional numerical model to study a mine operating in the Pittsburgh seam. The influence of random field data on entry roof was investigated. The realistic random field database added two scale-measured parameters from horizontal and vertical directions to control the spatial correlation length. A number of cutting sequences were also considered in order to identify the effect of spatial variance on roof behavior. The results show that spatial variance provides an accurate prediction of erratic roof falls in coal mines.

By W. G. Pariseau

Joints may be taken into account when using numerical modeling as an aid to mine design by embedding joints in the model. When using the popular finite element method, say UT3PC, a pre-analysis step is necessary, Step 0. This step is for the computation of equivalent properties of a representative elementary volume of jointed rock (REV) in the model. This Step 0 is taken before Steps 1, 2 and 3 for specification of a rock properties file, generation of the mesh, and model analysis are taken. A brief explanation of equivalent properties and several examples aid in explaining the details of Step 0. Focus is on procedures, input files, and output to show ease of computation. Theoretical details are relegated to references (e.g. Pariseau 2022). Comparisons of safety factor distributions about example mine excavations with direct scaling from mine observations then offer some insights concerning equivalent properties, especially strengths.

Feb 1, 2023

By K. W. Harris, K. A. Perry

Reserve depletion in Central Appalachia is continuously creating unique ground conditions for underground coal mines with many of these difficult environments directly attributable to multiple seam mining and/or deeper overburdens. While many empirical studies have been performed in an effort to improve understanding of these problems along with potentially improving safety and extraction, many of the difficulties encountered lie outside of the normal realm of expected behavior. This is often the case when mining in bump prone ground, where additional concerns are introduced and design buffers are warranted. The boundary element software LaModel was used to study three bump events in a deep-cover, multiple-seam reserve located in Harlan county in the Kentucky region of Central Appalachia. This region is notoriously bump prone due to significant areas of deep cover, the presence of strong to massive lithology (such as sandstone), and an extensive history of underground mining that increases the probability of multiple seam interactions. Multiple seam interactions are best understood with respect to site-specific parameters, including both the geological and geometrical components of interburden, overburden and mine workings. Initially, empirical-based approaches (ARMPS/AMSS) were used when attempting to back-analyze the bump events. However, it was recognized that a more detailed investigation was necessary to understand the fundamental causes/conditions associated with the bump events. Consequently, the LaModel study resulted in a mine-specific calibration method for the reserve. With this method in place, enhanced bump prediction throughout the reserve is expected, such that the stability, recovery and safety of future mining may be improved.

Jan 1, 2014

A comprehensive understanding of the effects of autoclave configuration (batch, semi-batch, continuous) on the residence time necessary to achieve a target conversion is a prerequisite for design of commercial scale autoclaves. Particle size distribution, mineral and reagent concentrations, temperature and mixing also influence the conversion. This paper outlines the bases of using test data to predict performance of commercial scale autoclaves. Recommendations for coordinating test program design with selection of scale-up method are provided. Examples are given to illustrate the different levels of engineering effort needed to meet corresponding levels of design optimization and accuracy.

Jan 1, 1998

By Thomas E. Finch

Engineering mine design encompasses a range of situations, and each situation has its own range of detail and fineness. The most time consuming, and perhaps repetitive design situation involves evaluation of new or alternate mining methods. Many man years are consumed examing alternatives conjured up at all levels of the design team, from the number crunching engineer to the engineering manager. Many alternatives are intuitively disregarded, some are briefly evaluated and thrown out, and many others are started but not completed due to time constraints. All alternatives have similar input characteristics and evaluation procedures. In the design process, production requirements are known and equipment production capabilities are generated to determine the numbers and costs of an equipment type required to match a given situation. The end result is some comparative figure, typically cost per ton or yard upon which a decision is built. The similarity of input data and problem solving techniques lends design to computer solution. Computer aided equipment evaluation is not new to the mining industry. An existing and accepted technique is exemplified with the programs used by truck manufacturers. Given a haulage profile and production requirements, the number of anyone capacity, horsepower, tire size, gear ratio or similar characteristically identified truck can be determined. This information can be outputted in varying degrees of complexity and the results used with equally varying percentages of credibility by design or production engineers. Most engineers are willing to accept-the computer's effort with relief and a desire for belief. Although inherently more complex, the ultimate end of computer manipulation should be total mine design. This is an extremely large step in the evolution of mine design, and not many engineers, including the authors, believe the results would be directly applicable or necessarily correct. As with computer simulations of an operation, total computer design of mines requires such complex and lengthy input that each mine might be manually designed more quickly and cheaply. The existence of computer programs which initially evaluate a mining system or part of the system is upon us, however.

Jan 1, 1978

By G. G. Marino, Z. R. Widup

Marino Engineering Associates, Inc. (MEA) was asked to determine the effects of mining beneath a proposed roadway structure. In order to determine the subsidence potential and the magnitude of the mine stabilization costs it is important to know whether underground mining is present, and if so, to what a real extent. The site investigated had the potential to have mining in three different coal seams. To determine where mining was present MEAÕs borehole radar system was used. In summary, the borehole radar subsurface investigation validated that the available mine map in the most shallow coal seam was fairly accurate despite its age (1888), found no mining in the underlying coal seam and detected an area of unknown mining at a depth of about 300 ft in the lowest coal seam which was verified by subsequent drilling.

Jan 1, 2004

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

By S. Pastor, S. Hahn

"As the concept of autonomous haulage systems (AHS) moves from proto-types to production-ready applications, the operating performance of the haul road will become ‘mission critical’ to the overall success of autonomy in mining. Deterioration in road performance will require remediation, human intervention and significant, albeit temporary, changes to operating procedures, to accommodate road maintenance. With autonomous trucks comes the opportunity to reduce road formation and operating width, and therefore generating potentially significantly reductions in stripping ratios and improvements to mine economics, but only if the design of the road, and it’s associated deterioration rate, is predictable and manageable, based both on the materials used to construct the road and the maintenance interventions to be carried out on the road. This paper presents the assessment of a digital photogrammetric approach to the characterization of a mine haul road surfacing, or wearing course material. Design and maintenance parameters for these roads are currently determined from physical particle size distribution (PSD) assessments of ‘in-road’ material. However, this approach does not accommodate the need, nor leverage the benefits from, AHS. The digital imaging approach is assessed in this paper, using two standard digital analysis software tools, together with in-service mine haul road wearing course samples and images which are assessed to determine the applicability and reliability of the approach to deliver a real-time assessment of haul road surfacing conditions and thus to identify the road maintenance interventions required to address deterioration. INTRODUCTION Enhancements in mine road design, construction and management for the past 20 or more years has largely been focused on short-term tactical needs. These improvements have not been matched by advances in the fundamental technologies that underpin mine road design and management, and although the quality of mine roads have probably increased, many of fundamental and longer-term issues have yet to be addressed. With AHS’s evolving from prototype to production applications, any decision to implement these systems in a mine requires a thorough evaluation of impacts, not only operational improvements, but the inter-connectivity of this autonomy technology to other organizational processes. In developing an understanding, the full interactions that may affect autonomous truck behaviour due to changes in various sub-systems or external environments, haul road conditions and operating performance is a key consideration. This is as true in autonomous as well as in conventional mine truck-based hauling systems where the mine haul road network is a critical and vital component of the production process."

Jan 1, 2015

By S. Triantafyllidis

The tailings produced from the Kirki (Agios Filippos) high sulfidation epithermal deposit processing plant are laminated, weakly cemented and their particle size ranges from fine sand to fine silt. They are mainly composed of milling residues of gangue (quartz, dickite/kaolinite, pyrophyllite, illite); sulfides and secondary minerals (jarosite group minerals, butlerite, anglesite, beudantite and gypsum) are present to a lesser extent. They have high Pb and Zn (average 0.75 % and 0.57 % respectively) and low S (1.04 to 2.92 %), Cu, As, Cd, Ni and Sb content (average 248, 163, 59, 27, 20 g/t respectively). Stagnant waters forming small ponds on the surface of the impoundments exhibit low pH and high heavy metal and sulfate concentrations. Negative Net Neutralization Potential (NNP) characterizes the tailings, indicating moderate to high potential for acid generation. Application of the TCLP test revealed that the tailings are characterized as toxic because of the increased solubility of Pb and Cd. On the other hand, As TCLP solubility is very low.

Jan 1, 2006

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By G. Biles

The Eskay Creek Mine, a high-grade gold and silver underground mine in northwestern British Columbia started operations in late 1994. For the first three years of operation, ore was crushed to minus 2 inch; blended to satisfy smelter terms and direct shipped to smelters in Japan and Canada. Before commencing the above operations, preliminary evaluations had indicated that an extremely complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. Subsequently markets for raw ore were identified and underground mining and ore transportation operations, at a nominal production rate of 300 tonnes per day, were commenced. Exploration diamond drilling in 1995 and 1996 discovered additional lower grade mineralized zones, which are less economic or uneconomic as direct shipping ore. Testwork demonstrated that these lower grade zones could be upgraded to marketable concentrates in a simple flotation mill. The mill was built in 1997 and has been in operation since late 1997. The mining rate now has increased to 400 tonnes per day including 250 tonnes per day of the direct shipping ore and ISO tonnes per day of the mill ore. Prime Resources Group Inc. wholly owns the Eskay Creek Mine. Homestake Canada Inc. owns 50.6% of Prime's shares and manages and operates the mine on Prime's behalf. This paper discusses the mining and milling operations as well as ore shipment and smelter contracts' administration.

Jan 1, 1999

By Augusto Andres Torres Toledo, João Felipe Coimbra Leite Costa, Luciano Nunes Capponi, Diego Machado Marques

Short-term mine planning to open pit requires defining diglines to orientate the excavation geometry. In deposits with multiple chemical variables, it is necessary to have more rigorous control over the feeding of the processing plant. This study analyzes the impact of incorporating multiple chemical variables, the risks generated by geological uncertainty, and the number and starting point locations of shovels in the sequential design of diglines. The objective is to maintain and preserve the low-grade variability, required tonnage, and continuity in sequentially selecting blocks. To achieve this, the probability distribution function of each chemical variable is used while attempting to maintain the ore grades as constant as possible. As it is difficult to maintain multiple elements with low variability simultaneously, the relevance of each chemical variable in the economic benefit is identified. Weights are assigned to signal the importance of each element based on its significance in the recovery process. Several diglines, consisting of sequential blocks, were generated on the same seed point to meet the weekly ore demand. Optimizing the stationarity of multiple chemical variables, accessing and reducing the geological uncertainty performed through geostatistical simulation of grades and transfers functions, considering the number and location of shovels, while meeting the operational restrictions of the selected blocks. The optimized digline with the multiple grades as stationary as possible is retained. The process is illustrated in a phosphate mine. The results show that the proposed method is viable and allows for a quick solution.

Jun 25, 2023

By Pascal Deschamps

"INTRODUCTION During the last decades, many underground facilities for the storage of hydrocarbons have been excavated worldwide and the technology is fully mature. Similarly to other underground structures, the initial basic design has to be adapted along with the work progress, in order to cope with the actual site conditions and in particular the geology, hydrogeology and associated rockmass quality. In addition, Client’s or underground Contractor’s constraints (such as resources availability, schedule or cost impact) may vary from design to construction and require last minute adjustments. Engineers are required to introduce flexibility and anticipation of unexpected situations (similar to the above-mentioned) while conceiving large underground facilities. Although most of the cases require only minor adaptations, crucial parts of the facility have sometimes to be considerably modified and reviewed. This article will present four cases evidencing how the design of one of these essential structures - the concrete plug – has been adjusted during site implementation without impairing the initial performances. Hydrodynamic containment The product containment of the unlined caverns discussed here is ensured by the principle of hydrodynamic containment. A permanent water flow is naturally or artificially maintained with an orientation toward the storage cavern and then, neither product-tight membrane nor lining are required. The hydraulic gradient (and the associated water flow lines), being directed from the surrounding mass toward the cavern, prevent from outward migration of the product. If the hydraulic gradient is not sufficient or if the water table is evidencing instability, water can be artificially injected into the rockmass through purpose-built boreholes, drilled from dedicated galleries. This water injection system, called the water curtain, is generally located several tens of meters above the level of the cavern. This principle is illustrated here after."

Jan 1, 2016

By E. Bakhtavar

It is considered that the most economical method for the exploitation of Gol-e-Gohar Area 3 iron ore mine is to combine open-pit and underground methods. In this regard, the most critical problem is the determination of optimal final pit depth. In this paper, a method which was recently introduced on the basis of economical block models of open-pit and underground is used to determine optimal final open-pit depth of Gol-e-Gohar Area 3 mine with due regards to the future underground mining option. Considering a low cost and productive underground method as a feasible alternative for extraction of the lower part of this deposit, room and pillar was selected. It is concluded that after the assessment and comparison of different values for depth, optimal final open-pit depth was determined to be equal to 285 m.

Jan 1, 2010

By L. A. Pursell

The case history, which is the subject of this paper, involves the expansion of a lime plant in Texas. The major new production unit is to be a 545.45 tonne per day coal fired rotary kiln. Auxiliary facilities include additional quarry haulage equipment, modifications to the crushing plant, a hydrator, storage facilities, and a loading system. The existing plant consists of a high calcium limestone quarry, two coal fired rotary and 10 gas fired shaft kilns, nth crushing, screening, stockpiling, hydrating, storing and loading facilities. The proposed modification would increase quarry volume from 545,000 tonnes per year to 805,000 tonnes per year. The plan also includes the addition of dolomitic lime to the product line which requires the purchase and handling of 186,000 tonnes of screened, washed dolomite yearly. A decision to undertake such an expansion was previously a simple and straight forward process. Such a decision now faces a major and complicating obstacle which can delay the project, raise the expected cost, or prevent it entirely.

Jan 1, 1980