Search Documents

By J. H. Bulloch

A study of fatigue-crack growth in a rail steel and an associated weld metal showed that fatigue cracks in the deformed rail steel had slightly higher growth rates than in undeformed rail steel. The crack growth in the weld metal was appreciably faster than either and exhibited plateaux that were above the upper bound reported for rail steels, The cyclic-life curves showed that, over an indicated service period of 8 years, both the deformed and the undeformed rail steels should not be prone to fatigue failures under the defined mechanical conditions, For the weld metal, the cyclic-life curves indicated the possibility of premature fatigue failures but, as al the input parameters represented a 'worst case' situation, this assessment could wel be ultra-conservative. In the rail steels at low levels, the extension of the fatigue cracks occurred by ductile striated growth. At a Kmax level of 35 MPa .J/n, cleavage facets formed initially on the surface of the fatigue fractures, and their incidence increased with Kmax until the onset of fast failure, The microstructure of the deformed rail steel exhibited cleavage facets at a slightly lower Kmaxvalue, and contained more cleavage facets at a given K level, than the microstructure of the undeformed rail steel. The average size of the cleavage facets agreed well with the pearlite nodule dimensions of 60 to 100 ILm. The microstructure of the weld metal was much coarser and contained columnar grains. At al f.K levels, the dominant fracture mode was cleavage, with small isolated regions of ductile striated fatigue cracks. The size of the cleavage facets varied from 150 to 600 ILm, and such a variation may be explained by the fact that cracking generally occurs in association with the pro-eutectoid ferite phase, and that this phase is distributed along some boundaries of prior austenite grains and the boundaries of the coarser columnar grains.

Jan 1, 1987

By D. Burrows

Traditionally, characterisation of the mineralogy and textures of ore and rock samples were based on observations of hand specimens and thin sections using an optical microscope. The extent of the data collection was limited by the available tools and thus variations in mineralogy and texture were generally not described by quantitative data. These qualitative to semi-quantitative approaches, even though well established over the years, resulted in variable observations and data sets. The data were unlikely to be representative of a sample and limited statistical validity meant the results could not be reliably used in modern digital mining design and planning. With recently developed SEM based quantitative mineralogy tools and the corresponding methodologies, ore textures can be quantified and compared numerically. The numerical data can not only enhance the understanding of an orebody in geological terms, but can also be used in the creation of metallurgical models for mine and mineral processing design and simulation. These capabilities provide valuable inputs to risk assessment studies and the evaluation of mineral projects.

Jan 1, 2007

Notices STRASZACKERREPORT The Institute has received, for its information, a copy of the following letter, which was addressed to The Federation of Societies of Professional Engineers: REPORT: COMMISSION OF ENQUIRY INTO THE METHODS OF TRAINING FOR UNIVERSITY DEGREES IN ENGINEERING (STRASZACKER REPORT) Geagte Heer, VERSLAG: KOMMISSIE VAN ONDERSOEK NA DIE METODE VAN OPLEIDING VIR UNIVERSITEITSGRADE IN INGENIEURSWESE (STRASZACKERVERSLAG) Second International Symposium on Jet Cutting Technology This symposium, sponsored and organised by BHRA Fluid Engineering, of Cranfield, England, is to be held at St John's College, Cambridge, from 2nd to 4th April, 1974. Competition for student members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Techomin 74 - World Mining Fair The above World Mining Fair, under the sponsorship of the International Committee for the Organization of World Mining Congresses and the Peruvian Government, is to be held in Lima, Peru, from 3rd to 12th November, 1974, to coincide with the 1974 World Mining Congress, which is to be held in Lima. NIM Reports Report No. 1435 The determination of chromium, manganese, iron, cobalt, and nickel by atomicabsorption spectrophotometry using the nitrous oxide-acetylene flame. Report No. 1463 Liq'uidus temperatures and activities of manganese (11) oxide in slags associated with the production of high-carbon ferromanganese alloys. Report No. 1467 The spectral analysis of solutions. 1. The analysis of rare-earth minerals. Report No. 1479 Infrared studies of the adsorption of oleate species on mineral surfaces,with special reference to fluorite. Report No. 1483 The South African manpower requirements in extractive metallurgy. Report No. 1484 Cost estimates for the production of copper wirebars from sulphidic ores. Report No. 1486 Review of the jluoro-chemical industry of the World. Report No. 1490 The adsorption of krypton, nitrogen, and water vapour on sodium oleate. Report No. 1491 Technology and economics of the Olaus kiln under South African conditions. De Beers Report The dry grinding of tungsten carbide/ steel combinations with diamond wheels. Metallurgical Directory The Israel Export Institute has just published the first edition of the Israel Metal Industry Directory, which gives pertinent information relating to the 750 Israeli manufacturers of metal products-addresses, annual turnover, and products- and to consulting engineers and export companies specializing in metal products. Visiting Nuclear Scientist The National Institute for Metallurgy has announced that Professor Vincent P. Guinn, of the University of California, is to spend his sabbatical leave (April to June) working with the Activation Analysis Research Group of the National Institute for Metallurgy.

"Chairman: Mr R. A. PLUMBRIDGE Rapporteur: Dr D. M. HAWKINSPapers:The relevance of computer methods to the economics of the mineral industry by R: A. PerlmanDynamic control of a mining enterprise by R. G. CoyleAn economic model of the mineral sands industry by G. P. A. HoweMr M. Splaine, in opening the discussion on Mr Perlman's paper, asked whether the model, as fitted by data up to 1963, predicted the rise in the price of copper in 1967, and whether the model could be used to capitalize on short-term price fluctuations.Answering the second question first, Mr Perlman said that the horizon used is six months to one year. In the very short term the activities of speculators obscured the effect of the fundamental econometric variables. This effect, however, was removed if one moved to a longer term, say, quarterly. In 1963 the model had predicted a price rise in 1964 and 1965 and a drop in price in 1966. The rise in 1967 had been caused by a strike, and imponderables such as large strikes were difficult to include in the model since they were unpredictable. Model simulation can be used to show the effect of strikes on price and the effect of small strikes is small.Mr B. R. van Rooyen said that because models are both calibrated and tested on historical data a bias was introduced which gave rise to an overoptimistic estimate of the accuracy of the forecasts. To this Mr Perlman replied that there seemed to be no alternative to the use of historical data for calibrating and testing models, and thus little hope of avoiding the bias. A second point made by Mr. van Rooyen was that manage¬ment tended to be suspicious of complex models and that frequently more heuristic models were sufficiently accurate and preferable for investment decisions. He added that if management were not involved in the model building the econometrician might easily go astray, Mr Perlman replied that symbiosis between data analysts and users of the model was essential and that the experience of the practitioner must be reflected in the model.Mr M. R. Fuller-Good remarked that a clear understanding of future price trends was essential for effective capital planning, and asked, first, how one went from the compiled data on supply and demand to the determination of their effect on price, record, whether necessary data, for example, capacities, could be obtained timeously, and, third, when strikes restricted supply, whether stockpiling by consumers induced large price fluctuations."

Jan 1, 2014

P.W.D. ROSTER OF CONSULTING ENGINEERS (Extract from a letter from the Secretary for Public Works) In recent years a large number of professional engineers has entered the consulting field. Although the names of most of these have been placed on the Department's roster of consulting engineers either as a result of representations made by the South African Association of Consulting Engineers or by applying direct to the Department there are still some who seem to think that canvassing through an influential person is necessary to obtain commissions from the Department. The Department's roster is open to all registered professional engineers who are suitably experienced to undertake consulting work and commissions are awarded strictly on merit. I shall appreciate it, therefore, if registered professional engineers who wish to be considered for commissions by the Department could be advised that they must apply, in the first instance, to be placed on the Department's roster. On receipt of such an application a questionnaire listing all the information required by the Department will be forwarded to the applicants for completion and returning to the Department for record purposes. All names which appear on the roster are taken into account when a commission has to be awarded, due consideration being given to factors such as geographical position, seniority, capability and compatibility. AMERICAN SOCIETY OF MINING ENGINEERS 1970 FALL MEETING AND EXHIBIT The Secretary for Commerce has passed to us a letter received from the American Society of Mining Engineers, reading as follows: "We would be delighted to have South Africa attend our meeting next year and to exhibit some of their mining equipment in our Technological Information Exchange. The 1970 SME Fall Meeting and Exhibit will be held in St. Louis, Mo., October 21-23, 1970, at the Kiel Auditorium. The AIME WorId Conference on Lead & Zinc Mining and Metallurgy will be an integral part of our meeting-and an added incentive to attend. It should be understood that we discourage the showing of actual mining equipment and encourage the manufacturers and suppliers to send their engineers to man the booths. We hope that the exhibits will endeavour to put across their story by means of photographs, drawings, models and literature, rather than by display of prototypes of the actual equipment. We will be happy to welcome manufacturerers from South Africa as well as the mining engineers who, from time to time, have registered at our meetings." For further particulars, interested parties may write to the Society of Mining Engineers, 345 East 47th Street, New York, N.Y. 10077, D.S.A.

By A. Mehmet

The feasibility of employing a multi-stage column for the recovery of gold from cyanided pulps using extruded carbon was investigated on a pilot-plant scale. It was anticipated that the column contactor would have certain advantages over conventional carbon-in-pulp plants. The feed pulp was screened to remove particles larger than 200 µm and was diluted to a solids concentration of about 23 per cent. The column was operated continuously for 24 days at a pulp flowrate of about 60 l/min and a carbon flowrate of 44 litres per day. The average gold concentrations in the barren pulp 12 hours and 24 hours after the carbon transfer were 0,012 and 0,031 mg/l respectively. The average gold concentration in the solution phase in the feed was about 2,0 mg/L. The average gold Loading on the carbon was 6290 g/t. Calcium carbonate was removed from the loaded carbon by treatment with 0,5 bed volumes of 2,8 per cent hydrochloric acid solution at ambient temperature. The calcium concentration was reduced from about 17 000 to about 500 g/t The carbon was eluted by the Zadra procedure at atmospheric pressure. The results of the elution were highly satisfactory, the gold concentration being reduced from about 6000 to about 20 g/t in 48 hours. The eluted carbon was regenerated in a Rintoul kiln at about 700°C. The activity of the regenerated carbon was found to be at least as high as that of fresh carbon.

Jan 1, 1992

By A. P. Cook

Gas samples were taken from a wide range of target areas on dumps arising from coal mining activities. Some of the dumps had largely burned out, some were still burning, some were in the process of rehabilitation, and on others rehabilitation was essentially complete. It was found that rehabilitation was very effective in reducing emissions to tolerable levels. Even incomplete rehabilitation reduced the CO2 emissions to less than about 1 kg/m2/a, whereas some unrehabilitated areas showed emissions of over 100 kg/m2/a. Some areas where there was active combustion taking place were also sampled, and they showed as much as 7 000 kg/m2/a, but the areas concerned were very small and their total contribution accordingly low. Analyses were also made for SOx, NOx, NH3, and CH4, but these were generally (and unexpectedly) at very low levels. The mines sampled represented 53 per cent of all surface coal mining activity. Accordingly the estimated total emissions were scaled up, to arrive at estimates of 1950 000 ± 350 000 t/a C02, 2040 ± 580 t/a SOx, 306 ± 85t/a NOx, and 31 ± 9 t/a NH3 for all surface mines. Methane was detected only from burning coal, and due to the difficulty in sampling, no reliable estimate could be made of these methane emissions.

Jan 1, 2012

1. Book reviews Underwater tools, by Donald J. Hackman and Don W. Candy. Columbus (D.S.A.), Battelle Press, 1981. 152 pp. $32,95. Reviewer: B. Schmitz Uranium exploration case histories. Proceedings of Advisory Group Meeting Vienna, IAEA, 1981. Price: Austrian schillings 630. Reviewer: E. C. Kostlin Jet cutting technology, a review and bibliography, edited by Robin Brown. Published by BHRA Fluid Engineering, Cranfield, Bedford MK430AJ, England. Reviewer: D. O'Beirne 2. New Books Proceedings, Twelfth Congress of the Council of Mining and Metallurgical Institutions, by H. W. Glen (editor.) Johannesburg, The South African Institute of Mining and Metallurgy, 1982. 2 vols., 1060 pp. R78,85 (air-mail RI53,85). Amborite. Johannesburg, De Beers Industrial Diamond Division (P.O. Box 916), 1982. 6 pp. Free of charge. 3. New Journal BHRA Fluid Engineering has announced its new journal World Ports and Harbour Abstracts and the associated newsletter World Ports and Harbour News, which are issued from January 1983. The Abstracts is published bi-monthly and costs £60 in the V.K. and E.E.C., and £72 elsewhere. 4. Mintek reports Report 2134D On-line analysis, by X-ray diffraction, of fluorsparcontaining slurries. (First published 30th Sep., 1981.) Report 2135D A preliminary on-line analysis, by X-ray diffraction, of pyrite-containing slurries. (First published 30th Sep., 1981.) Report M28 The measurement of flow velocity distribution in fluids. Report M34 The determination, by atomic-absorption spectrophotometryusing electrothermal atomization, of platinum,palladium, rhodium, ruthenium, and iridium. Report M45 Two computer programmes for the calculation of massand heat balances in the production of high-carbon ferromanganese. Report M50 The development of an on-line gold analyser. Report M54 Major amounts of mercury in native gold from upper Witwatersrand sediments. Report M55 A new robust method for the treatment of analytical data. Report M57 The hydrometallurgical treatment of liquors generated by the leaching of a low-grade matte. Awards for inventions For inventing devices of exceptional value to the mining industry, two mining men were presented with awards in Johannesburg on 25th November, 1982, under the Chamber of Mines' Ideas and Suggestions Scheme. Mr W. W. Malan, President of the Chamber of Mines, made the presentations.

Jan 1, 1983

H. W. Glen (ed.). Proceedings of Asbestos Symposium, Johannesburg, South, Africa, 3rd-7th, October, 1977. Randburg, National Institute for Metallurgy, 1978. 158 pp. (Copies obtainable from the Department of Mines, P.O. Box 4584, Johannesburg, 2000 South Africa.) This Symposium, which concentrated on the theme of dose-response relationships for asbestos-related diseases, was attended by an internationally representative group of experts in this field. Bulk solids The Powder Advisory Centre announces its third annual International Conference on Bulk Solids Swrage, Handling and Flow, to be held at the Holiday Inn, Liverpool, on 7th to 9th November, 1978. This sequel to the extremely successful November '76 Stratford and November '77 Nottingham Conferences is again to be co-sponsored by a number of internationally acknowledged professional societies, including the Institute of Materials Handling (through its Bulk Solids Panel), the Institution of Production Engineers, and the American Society of Mechanical Engineers (through its Materials Handling Engineering Division). NIM reports Report no. 1943 A review of the literature on the separation and determination of rare-earth elements. (23rd Mar., 1978.) Report no. 1947 The cation- and anion-exchange behaviour of various base-metal chlorides in polar organic solvents. (lOth Mar., 1978.) Report no. 1948 The measurement of trace amounts of gold in solution by atomic-absorption spectrophotometry and carbon-rod atomization. (28th Feb., 1978.) Report no. 1949 The kinetics of the leaching of zinc sulphide concentrates in acidic solutions containing ferric sulphate. (23rd Mar., 1978.) Report no. 1950 Factors affecting the carbon contents of alloys formed during the prereduction of chromite ores. (31st Mar., 1978.) Report no. 1952 The effect of slag composition on copper losses to silicasaturated iron silicate slags. (31st Mar., 1978.) Report no. 1953 A fundamental investigation into the depression of copper-activated sphalerite. (28th Apr., 1978.) Report no. 1956 An improved ion-exchange separation of rare-earth elements for spectrographic analysis. (10th Mar., 1978.) Report no. 1960 The recovery of ferrochromium from furnace slags and related products. (20th Aug., 1976; declassified 31st Mar., 1978.) Process instrumentation The National Institute for Metallurgy and the South African Institute of Measurement and Control are organizing a symposium that will draw the attention of researchers and industrial workers to the importance of metallurgical process instrumentation.

Jan 1, 1978

AFRICAN NATIONAL COMMITTEE ON TUNNELLING In 1970, the South African Institution of Civil Engineers, the South African Institute of Mining and Metallurgy, the South African Institute of Mechanical Engineers, and the Geological Society of South Africa held an international conference on tunnelling, known as Tuncon 1970. SUID-AFRIKAANSE NASIONALE TONNELBOUKOMITEE In 1970 het die Suid-Afrikaanse Instituut van Siviele Ingenieurs, die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie, die Suid-Afrikaanse Instituut van Meganiese Ingenieurs en Die Geologiese Vereniging van Suid-Afrika 'n internasionale konferensie in verband met tonnelbou gehou, wat bekend gestaan het as Tonkon 1970.

Jan 5, 1974

By C. M. G. Wortley

One of the major deliverables of the AMIRA P754 Project, which was sponsored by several major mining companies, was a code of practice and guidelines for metal accounting for the mining and metallurgical industry. These had the objective of improving the auditability and transparency of metal accounting from mine to product, thus assisting in good corporate governance. The overriding objective of mass measurement for metal accounting is to establish the mass of the particular material or component present at a specific time, or the mass flow of that component over a defined time period, to a defined accuracy suitable for metal balancing. As such, it is the first measurement in the chain that includes sampling, sample preparation and analysis, each of which introduces its own errors. Materials often contain moisture, the proportion of which must also be established in order to obtain the dry mass. They may also have to be measured as a volume or mass/mass flow of slurry, or in stockpiles or storage areas, in which case the relative density must be measured. Both the density and moisture measurement often introduce significant error. Whereas a great deal of effort has been directed at sampling, sample preparation and analysis to improve accuracy and establish the error, the same can seldom be said for the mass determination, including the moisture and density measurements. The possible major causes of error are highlighted and methods of reducing them discussed. Mass measurement can be classified into those measurements necessary for custody transfer and primary accounting of the input and output streams to a plant or operation, and measurements required for secondary accounting, or management control. The latter include intra company transfers and plant area performance, and those required for plant control only. This paper is concerned only with primary accounting measurements. The code and best practice state that the equipment should be certified (as sized) as is required for custody transfer. The most accurate and precise of the various possible methods is the static measurement of mass on a weighbridge, platform scale or a weigh bin. If static measurement is not possible, which is often the case for ore fed to a plant, possible alternatives are electromechanical conveyor belt weighers or in-motion weighing of rail trucks. In all cases the material must be adequately sampled to enable a representative moisture content to be determined to calculate the dry mass. Where material is flowing inside conduits, only certain types of the multiplicity of flow meters available may be used and, in the case of slurries, very few flow meters are suitable. As most flow meters measure volume or velocity, the density of the material must also be measured. The basic requirements in order to achieve satisfactory results for the mass, of the component of interest, are listed, as well as common problems and pitfalls encountered in practice. The measurement of the mass of stockpiles and in-plant stocks, often required for metal accounting, is often the largest source of error in metal balances. The reasons for this and methods for reducing and managing the effect are discussed.

Jan 1, 2009

By M. Frenzel, K. Bachmann, M. Rudolph, R. Tolosana-Delgado, E. Schach, M. Buchmann, L. Pereiraa, K. G. van den Boogaart, N. Kupka

Geometallurgy - the science of predicting the behaviour of ores along the value chain based on their geological and mineralogical characteristics - has barely moved beyond process minerology studies. These studies typically link process behaviour to the mineralogical and microstructural characteristics of pristine or processed ores in a qualitative or semi-quantitative manner. Eventually, a trial-and-error optimisation of the operation is achieved. However, to deliver on its promise, geometallurgy should progress beyond this current approach to a fully quantitative understanding of process behaviour, including the various uncertainties involved, namely predictive geometallurgy. One of the barriers currently hindering this development is the neglect of most ore characterisation data obtained in geometallurgical studies. This is mostly due to the large extent of this information exceeding the capacity of conventional software. To address this challenge, we developed a data mining platform consisting of an SQL database, an R front-end in-house package, and back-ends to interpret data from several analytical instruments. This platform enables the use of the statistical and data mining power of the R open-source environment for any geometallurgical study. Potential applications range from ore characterisation to process understanding and forecasting, and from geostatistical prediction to operational control and optimisation. The scripting abilities of R allow for the: 1) processing of many streams in loops, thus freeing the user from repeating tedious click-and-drop tasks; 2) computation of virtually any derivate or aggregate quantity from the data; 3) distribution of the work among several processor clusters; and 4) keeping of a log file for the calculations done. This contribution presents the building blocks of this platform, and illustrates with several examples its potential to enable predictive geometallurgy. Keywords: Data mining, entropy, kernel methods, LASSO regression, predictive geometallurgy

Jan 1, 2020

By J Taguta, B. McFadzean, P. E. Ngoepe, M. G. Mulaudzi

Computational modelling methods and isothermal titration calorimetry (ITC) were employed to investigate the interaction of a pyrite surface with thiol collectors. Modelling work was conducted in the presence and absence of water. Microcalorimetry was employed to investigate the resultant energy of interaction pyrite as a result of mineral-collector interactions. Sodium ethyl xanthate (SEX), diethyldithiocarbamate (DTC) and diethyl dithiophosphate (DTP) were investigated in this study. The results showed that the calculated surface energies and morphologies for FeS2 showed that (100) and (111) are the most stable surfaces. The morphology also indicated the appearance of the (100) and (111) surface facets and no presence of others. The calculated adsorption energies between thiol collectors and the pyrite surface were always more exothermic than the experimentally determined ones. When comparing different ligand types with the same alkyl chain length, the heat of adsorption of diethyl-DTC was greater than that of ethyl xanthate and diethyl-DTP for pyrite. Experimentally, the diethyl DTP barely adsorbed onto the pyrite surface and this may be due to a different mechanism of action. In computational calculations, water adsorption was found to reduce the reactivity of the Fe atom for the interaction with thiol collectors, and bring the adsorption energies closer to the magnitude of the experimental values. Keywords: Computational modelling, microcalorimetry, experimental and thiol collectors, adsorption energies

Jan 1, 2020

A Colloquium and General Meeting was held jointly with the Mine Ventilation Society of S.A. in Kelvin House, Johannesburg, on 17th November, 1971, the theme being "The Economics of Mine Ventilation". Professor D. Howat (President) was in the chair. The Colloquium was attended by 150 delegates and was opened by the President at 9.00 a.m. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following Grades: Fellows: Frederich-Wilhelm Volk, Peter Bennet Columbine. Members: Allan Colin Lawrence, Karel Anton van Gessel, Christopher Robert Harrison, Christopher Michael George Wartley, Frank Heinrich Deist, Ralph Morris, Benjamin Johannes Nolte. Associates: Wolf gang Freidrich Gottsman. TRANSFERS From Member to Fellow: Hugh Edward Keith Alien. From Graduate to Member: Errol Vincent Bosman, Christopher Roderick Stewart Needes, Bernard Wessels Holthousen. From Student to Graduate: David Robert Fleming. I welcome the new members to the Institute and congratulate them on their election. CO-OPTION TO COUNCIL The President announced that at the Council meeting held on 5th October, 1971, it was agreed, in terms of Rule 3.9 to co-opt Dr T. B. Beeton to Council. COLLOQUIUM The President welcomed visitors and members. He stressed that the discussion would be informal and that any contributor requiring publication should submit his contribution in writing. He then thanked the authors for providing pre-prints of the papers. After the President had concluded his opening remarks, he asked Professor J. de V. Lambrechts to act as Colloquium Chairman for the day and he, in turn, introduced the three Session Chairmen namely, Dr A. Whillier (Chamber of Mines and President of the Mine Ventilation Society); Mr M. Barcza (Managing Director, Corner House Laboratories); and Mr L. W. P. v.d. Bosch (Chief Consulting Engineer, Union Corporation). The following papers were presented: "Fan efficiency investigation on mines of the Union Corporation, Ltd." by J. A. Drummond. Published in the Journal Feb. 1972. "The design of underground cooling towers" by A. Whilliel'. Published in the Journal, Oct. 1971. "Some aspects of the design of cooling plant installations" by R. Hemp. Published in the Journal, Nov. 1971. "The planning of ventilation and refrigeration requirements in deep mines" by D. F. H. Grave and R. M. Stroh. Published in the Journal, Dec. 1971. "Cooling power of underground environments" by D. Mitchell and A. Whillier. Published in the Journal, Oct. 1971. At the conclusion of the three technical sessions the Symposium Chairman commented as follows, indicating that he would prepare a written summing up at a later stage: "The tone of the colloquium has had a sincerely practical note about it. It would have been a pity if the ventilation experts talked only theory and little practice. This practical theme has, I am sure, made the colloquium interesting to both ventilation men and others whose daily tasks do not touch so closely on this fascinating subject. This practical theme was in evidence through all the papers and contributions. Some of you may have felt that there was not enough emphasis on the word 'economics' as advertised in the broad title of the colloquium. I do not think this was really a valid criticism because as someone said 'it all boils down to Rands in the end!' So whether it was a case of low fan efficiency, poor design of cooling towers, wrong planning or low human efficiency due to high heat stress. . . it all boils down to money saving and therefore economics, whenever improvements are forthcoming. The title of the colloquium was thus not misplaced. The views of senior mining men on the production side are appreciated. Let us say that this exchange of views between ventilation engineers and those who have to take the final decisions and spend the money, should prove to be most rewarding." Professor Lambrechts finally thanked the Session Chairmen and everybody who had helped to make the colloquium a success and the meeting closed at 4.0 p.m. In a subsequent written summing up, the Colloquium Chairman gave the following as his impressions of some of the highlights which emerged from the papers and discussion thereof: (The names indicate the authors only). Drummond: It was hinted that the time had arrived to consider the introduction of a South African fan test code which would be better suited to local conditions than the currently acknowledged B.S.S. code which, however, is seldom enforceable in practice. In this connection also, there was prominent reference to the thermodynamic approach of McPherson. Wide variations in the quality of maintenance of, and repair work on, fans were stressed. It was mooted that ventilation engineers responsible for estimating the basic duty specifications for large fans, frequently played safe by overestimating the pressure required, thus ensuring that there would not be a shortfall in air volume delivered. This usually meant reduced fan efficiency and it was suggested that decision makers seemed to lay more emphasis on volume of air delivered than on real eco-

1. Recent publication Iron and steel works of the world. Worcester Park (England), Metal Bulletin PLC, 1987. 9th edition, 728 pp. £94.75 by air mail.2. Canadian publications Mining and mineral processing operations in Canada, 1987. Mineral Bulletin MR 216. $15. (Obtainable from Printing and Publishing, Supply and Services Canada, Hull, Quebec, KIA 059 Canada.) Peat producers in Canada, 1986 directory, by M. Prud'homme. MRI 87/7 Canadian mines: Perspective from 1986. Reserves, production capability, exploration, development. Mineral Buletin MR 215. $9.95. 3. Mintek publications Report M313 The testing of abrasion resistance in pipeline materials, by D.P. Enright. Nov. 1987. 36 pp. Report M328 The installation and commissioning of a Hilger Monospek D500 scanning monochromator, by A.E. Watson. Sep. 1987. 11 pp. Report M331 The design and operation of hot-air dryers for the drying of granular activated carbon. Nov. 1987. 30 pp. Report M338 Ore microscopy, image analysis, and the extractive metallurgy of sulphide minerals-an overview. Nov. 1987. 14 pp. Report M339 The determination, by flow-injection analysis, of sulphate in solutions containing chromium(I/I) and iron(I/I). Nov. 1987. 11 pp. Report M222D The simultaneous determination of common anions by ion chromatography, by A. Cameron and C. Pohlandt. Oct. 1985, reissued May 1987. 10 pp. Report M227D The spectrophotometric determination of silica in metallurgical-grade fluorspar, by M. Solomons. Nov. 1985, reissued Jun. 1987. 9 pp. Report M229D The determination of metalic iron in prereduced iron ores, by R. Lownsbrough. Dec. 1985, reissued Jun. 1987. 7 pp. Report M252D The spectrophotometric determination of bismuth in sulphide materials, by M. Solomons. Mar. 1986, reissued Jun. 1987. 13 pp. Special Publication no. 12 Platinum in South Africa, by A.M. Edwards and Silk. 1987. 64 pp. Illustrated in colour. R30 ( Africa), US$30 (other countries). 4. Journals of interest Industrial Minerals. London, Metal Bulletin Journals Ltd. Tin and its uses no. 154, Nov. 1987.

Jan 1, 1988

The February General Meeting of the Branch was held at the St. Helena Club on Wednesday, 19th February, 1969. Present were: Twelve members: Mr J. G. Kirchner (Chairman of the O.F.S. Branch), Messrs J. N. Saunders, N. A. Honnet, L. O. W. Leimer (Committee Members), Messrs R. C. Espley-Jones, J. W. Wilson, A. T. Lewis, A. von Holdt, L. J. Thorne, C. Mostert, V. O. Steed, H. H. Schellhorn. Nine Associate Members: Messrs E. R. Penny, G. T. C. Emere, M. Forster, K. Pearce, R. B. Sutherland, D. E. Couperthwaite,A. H. Edwards, M. D. de Lange, G. ,R. Still. Four Graduates: Messrs M. H. Smith, N. Mayer, T. R. Stromsoe, T. A. Ward. Four Affiliates: Messrs D. S. Robinson, L. D. Hulley, R. B. Smith, R. L. Soll11s.One Student: D. R. Fleming. Twenty-three Visitors. Total present: 53. Apologies were received from Messrs C. R. Netscher, A. Leger and V. C. Barnes. MINUTES OF PREVIOUS GENERAL MEETING The minutes of the General Meeting held on 15th November, 1968 and which were published in the February Journal, were taken as read and their adoption moved by Messrs J. N. Saunders and N. A. Honnet. There were no matters arising from the minutes. GENERAL BUSINESS The Chairman reminded members of the forthcoming visit by the Branch to the Dudfield Works of the Anglo-Alpha Cement Company, to take place on Wednesday 16th April. TALK ON ROCK MECHANICS The Chairman called upon Mr J. W. Wilson to address the meeting on the subject of the practical applications of rock mechanics to mining. Mr Wilson used a slide projector to present his subject in a most interesting and instructive manner which eventually resulted in much useful discussion taking place. The Chairman then called upon Mr A. von Holdt to thank the speaker. CLOSURE After thanking the speakers, the Chairman thanked members and visitors for their attendance and closed the meeting at about 10 p.m., after which refreshments were served.

By M. Kumral, S. Hmoud

Optimising the configuration of infill drill holes is an important step during mineral exploration campaigns. However, this optimisation process encompassing all possible drilling configurations within a mineral deposit is highly combinatorial and hard to solve in a reasonable time. This paper proposes using spatial clustering algorithms to divide the orebody into contiguous zones and target the best zones with infill drilling in order to reduce the size of this optimisation problem. Several clustering algorithms are assessed in a spatial context on hypothetical datasets. This evaluation shows that the hierarchical density-based spatial clustering application with noise (HDBSCAN) algorithm can be used in combination with the uniform manifold approximation and projection (UMAP) dimensionality reduction algorithm to identify contiguous zones in the orebody.

Sep 1, 2021

By W. Bleloch

Published in the Journal, September 1970, and presented at a colloquium on 'Future of the Steel Industry', 17th March, 1971. Errata (a) The final sentence in the penultimate paragraph, left hand column p. 34 of the text should read: 'In the hot regions of the bosh and stack the C+CO2=2CO reaction proceeds to CO from coke carbon and carbon dioxide generated by reduction of iron oxides by CO (the so-called solution loss of carbon)'. The italicised words have been omitted in the text. (b) Temperature in Fig. 3 is K not C. (c) In Fig. 9, connection from top plate of column 10 to heat exchanger 9 has been omitted. DISCUSSION J. B. BEEDON AND C. J. JONKER* Dr Bleloch's paper has outlined the advantages of recycling stack-gas of low nitrogen content in the blast furnace. In the first instance it would appear to be extremely beneficial in controlling the hearth temperature and allowing a 100 per cent oxygen-blast to be used. On a second point however we have to disagree. It is claimed that heat is liberated in the combustion zones by the oxidation of CO to CO2 near the tuyeres and in the subsequent reduction of the CO2 by CO. The author has hypothesized as follows, and we quote: 'The C+CO2=2 CO reaction in the outer combustion zone at about 1 700°C is no longer endothermic due to loss of stability of CO2 and its consequent dissociation into CO and free oxygen.' This statement requires closer examination. If we consider the individual events occurring with the CO in the recycled topgas, with the oxygen in the blast and with the coke in the burden, as done by Dr Bleloch, the following heat considerations emerge. All heats of reaction are calculated from the enthalpy values of each reactant and product, as well as the temperature dependence of their molar heat capacities. (a) At the tuyeres: CO+1/2 O2-+CO2 . . . . . (1) CO, CO2 at 500°C; O2 at 25°C. ?H reaction = -65 000 cals/mole CO The reaction (1) is exothermic. (b) In the outer combustion zone: CO2+C?2 CO . . . . . . . . (2) C, CO at 1 700°C; CO2 at 500 0C. ?H reaction = -56 000 cals/mole CO Reaction (2) is endothermic. The overall heat gain of reactions (1) and (2) is ?H=+56 000 - 65 000= -9000 cals/mole CO i.e. the overall reaction is slightly exothermic, the amount of heat liberated is however smaller than suggested by Dr Bleloch. (c) The dissociation CO2+CO+1/2 O2 . . . . . (3) is a highly endothermic reaction at 1 700 0C, requiring 82 000 cals/mole CO2 to proceed to completion. Furthermore, this reaction (3) is energetically not favoured to proceed, as can be observed from the free energy-temperature relationship of figure (3), which favours the formation of CO2 at 1 700 0C. Hence direct dissociation of CO2 at 1 700 0C appears to be unlikely.* The concept of recycling topgas is however still intriguing from many other points of view. Apart from providing a very efficient method of hearth temperature control, it will create a much higher CO partial pressure in the stack. Whether the rate of indirect reduction in the stack will be proportional to this partial pressure or not is un-

Jan 9, 1970

By R. I. Klintworth

The multi-reef area of Cooke 3 Shaft provides a unique mining challenge on account of the very thin middlings between the pay bands and the marginal values of the reef. It is uneconomic or impractical, because of the excessive heights, to mine the middlings using conventional stoping methods. The development of suitable mining methods is discussed with particular emphasis on the control of water inflow and the policy of not jeopardizing or sterilizing other reef horizons by the mining method implemented. No definite solution is currently available, but with the aid of instrumentation, computer analyses and mechanized mining equipment, the mine continues to attempt to maximize extraction and profits.

Jan 1, 1988

By L. Dison

This technical note is issued in two parts as follows. Part I, which appeared in the January issue of this Journal, after a brief introduction, discusses the value of patents and the law of patents, including patent applications and the exploitation of inventions. This is followed by some comments for the benefit of would-be inventors and potential users of patents. Part I focuses on the mining industry and then discusses views on patents that were quoted in Part I. The last section makes recommendations as to how inventors and users (including mining authorities) should handle patents.

Jan 1, 1992