Search Documents

By E. M. W. Skinner

Various models of near-surface kimberlite pipe emplacement have been proposed over the years. These include a top-down, phreatomagmatic model, a bottom-up, embryonic pipe model and three top-down explosive dyke models. AU of these models consider kimberlites as essentially the same rock type. However, different kimberlites have different pipe shapes and contain different rock types with very specific mineral assemblages and textures and therefore are likely to have been emplaced by different processes. Some authors have considered local geological differences as the principal reason for the contrasting geology but others argue that, while geological differences might contribute locally the petrographic peculiarities of particular kimberlites may be due mainly to inherent compositional differences specifically in the ratios of juvenile CO2 and H2O.

Jan 1, 2010

By B. Orgilbayar, B. Unursaikhan, S. Sukhbat, Ts. Zagarzusem, D. Baasanjav, L. Jargalsaikhan, E. Otgonjargal, N. Sugir-Erdene, Ts. Soyolmaa

This study has investigated the efficacy of the gravity beneficiation method based on gravitation and centrifugal forces for manganese ore. Powdered samples of manganese ores from the Unagad deposit in Mongolia were analysed for their element and mineralogical composition using ICP-MS and X-ray powder diffraction (XRD). The analysis presented the mineralogical compositions of the ores as hydro goethite, manganese minerals and magnetite, gangue minerals as quartz, albite, orthoclase and microcline of manganese ore. Manganese minerals are white in colour and have micro-veinlet, fine grained-aggregates associated with gangue minerals. The most important manganese minerals are hausmannite, pyrolusite, rhodochrosite, and manganosite. The composite of feed containing 17.31 % Mn and 36.3 % SiO2 was processed in a shaking table. In the experiment, a concentrate assaying 41.37% Mn was obtained from this composite with 65% recovery. In another experiment, f80=0.074 mm particle size ore was used in the MGS concentration test. A concentrate containing 38.34 % Mn with 75.2% recovery was produced in this experiment. The results showed that it is possible to obtain concentrate through gravity processing of manganese ore, which is an economically beneficial process for producing a product of a standard requirement. Keywords: Manganese ore, gravity separator, centrifuge, shaking table 1. Introduction

Jan 1, 2020

By M. Gericke

Over the past few decades the commercial application of heap bioleaching technology for the extraction of base metals has become increasingly important, due mainly to the depletion of high-grade ore reserves. Heap bioleaching is widely used for the extraction of copper from secondary copper sulphide ores. The design and engineering aspects of the process have received considerable attention, but issues related to the microbiology of the process have been subjected to less rigorous scrutiny. The major role of micro-organisms in bioleaching processes is to catalyse the regeneration of ferric iron and protons, from ferrous iron and by sulphur oxidation respectively. It is accepted that even the most carefully engineered heaps are heterogeneous in terms of temperature, pH, the presence of anaerobic pockets, irrigation efficiency, and dissolved solutes. Since interactions between solution chemistry, mineralogy, and microbial populations exist in heaps, a better understanding of the correlation between microbial numbers and types with changes in these chemical and physical profiles with time would be beneficial during process design and operation of heaps, and could result in faster start-up times and higher metal recoveries. This paper reviews the role of microbiology in heap bioleaching processes. Aspects such as microbial diversity, identification and monitoring of cultures, inoculation strategies, colonization behaviour, and tolerance to metals and salts are discussed, and the potential contribution of the knowledge to the improvement of the operation and design of heap bioleach processes assessed. Conclusions are drawn with respect to the role of genetic engineering, heap inoculation practises, and remaining areas for future heap bioleaching research and development.

Jan 1, 2012

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

Recovered activated carbon fines result from processing of ore and concentrates via cyanide leaching and sorption of valuable metals on carbon at gold-mining plants. This intermediate product is characterised by the particles sized smaller than 0.6 mm and gold grade up to 300-500 g/t. Processing of carbon fines with recovery of valuable metals is not available at many plants due to the lack of optimal technology. The paper describes the testwork and development of an efficient technology to process carbon fines with the recovery of valuable metals into the target gold alloy. This innovative technology involves pelletising of fine activated carbon particles using an organic binder, drying and further firing of pellets in a grate fired furnace at 800-900 °С. The produced ash is subject to sintering with sodium nitrate and hydroxide at 600-700°С. The sintered ash is then leached in water. The insoluble residue containing gold and silver is removed by filtration, dried and smelted to produce gold alloy. Water solution containing sulphur and arsenic is subject to detoxification. Processing of recovered carbon fines according to the developed technology implies the use of standard full-scale equipment. The offered method to treat gold-bearing carbon fines was patented by the Eurasian Patent Office. Key words: Fine activated carbon particles, valuable metals, pelletizing, firing, ash, sintering, leaching, smelting

Jan 1, 2020

By E. J. Magri

Consideration is given to the problem of the estimation, from limited data, of the likely grade and tonnage for a new mining property that is to be exploited by the selective mining of two metals that have substantial contributions to make to the total revenue. In particular, the case of a new gold and uranium mine in South Africa is analysed as follows. (I) The applicability of the underlying lognormal bivariate model for different support (i.e. ore unit) sizes is examined. (2) The necessary parameters for the bivariate lognormal models for different block sizes are estimated from abundant chipsampling data from a section of the Hartebeestfontein Gold Mine using alternative approaches, and the results are compared. (3) A method is given for obtaining the necessary parameters for a tonnage-grade relationship relative to a joint pay limit from the very limited information likely to be available at the end of the exploration stage of a gold mine, and the results are compared with those obtained from the large volume of data available from a minedout area.

Jan 1, 1982

By N. J. Alderman, R. Haldenwang

Flumes are ubiquitous throughout the mining and minerals processing industries as well as being used in the polymer processing and pulp and paper industries. With the increased demand for the transport of highly concentrated slurries in rectangular open channels, there is an impetus for a better understanding of the role of rheology in flow hydraulics. Until recently, design of such channels has been based on either the Chézy or Manning equations used for modelling open channel flow of Newtonian fluids. This has been done for modelling turbulent flow of low concentrated slurries with some success. However, this is not the case for highly concentrated slurries where the flow in the channel is no longer turbulent. Unlike Newtonian fluids, work carried out on flow of pseudo-homogeneous, non-Newtonian fluids in open channels is somewhat limited. Moreover, these results have been published in a variety of sources. This paper attempts to give a critical review of the work carried out on Newtonian and non-Newtonian flow of pseudo-homogeneous non-settling slurries in rectangular open channels. A comparison is also made of the models based on power law, Bingham plastic and Herschel-Bulkley fluids for laminar and turbulent flow in rectangular open channels.

Jan 1, 2007

By R. S. Francis

There are no manuals or handbooks for budding mill superintendents or process plant managers. Most who obtain this level of responsibility have gained their training from watching the good and bad of their predecessors and the successful ones have themselves graduated from the school of hard knocks. This paper attempts to provide some helpful guidelines and direction for those who aspire to better manage a mineral processing facility. The authors have 20 years combined experience in senior management roles at nine different mineral processing operations in Australia and overseas, covering gold, base metals and mineral sands. This summary of tips and pitfalls will hopefully benefit future leaders in mineral processing and metallurgy.

Jan 1, 2007

Review Mining annual review June 1979. London, Mining Journal, 1979. 624 pp. Available as part of the subscription to the Mining Journal or at £12,50 per copy. This annual review is recognized internationally as the world leader in reporting on metals and minerals, and is eagerly awaited each year for its authoritative content, which is compiled by well-respected experts throughout the world.

Jan 1, 1979

By N. B. Prenn, R. H. Robinson

"The model described is a design and economic planning tool for analyzing surface mineral deposits. Mineralization, topography, costs and significant geologic features are input to the model. The results are:(i) final pit limits yielding the maximum total profit,(ii) annual cut-off grades and plant sizing yielding the maximum present value, and(iii) annual maps of the pit and annual production statistics for the mine, concentrator and smelter.Additionally, summaries are printed of the block mining sequence and cash flow. A special feature is an option to include dump-leaching operations. Stockpiling of material can also be simulated by the model. The model is built around theories of dynamic cut-off grades and a pit design algorithm. The dynamic cut-off grades maximize present value by examination of all economic and physical constraints for the optimum combination. The pit design algorithm is a set of rules formulated to find the maximum value from a special graph. The graph is different from graphs of analytical geometry, being made up of points and arrows connecting some of the points. These graph elements describe the relationship between any point in the deposit and the material which must be mined to get at that point. The model was designed to bring together the interdependent theories of economics, pit design and production scheduling."

Jan 1, 2014

By P. G. Henderson, G. C. Thompson

The organization and mechanized colliery management of a large by G. C. THOMPSON, B.Sc. (Min. Eng.) (Witwatersrand), M.B.L. (Member), and P. G. HENDERSON, B.Sc. (Min. Eng.) (Pretoria), M.B.A. (Member). Usutu Collieries Limited, at present the largest single producer of coal in South Africa, supplies Cam den power station. and produces 435 000 tonnes per month by conventional mechanized methods from bord-and-pillar workings in three mines. The thickness of the seams averages 2 metres, and the depth below surface varies from 15 to 150 metres. Each mine depends to a different extent on certain common facilities and services. Two of the mines are located on the same coalfield, and their rationalization would possibly be advantageous. Production policy is one of productivity with flexibility. The double-loader system is widely used, and one section at each mine is worked on single shift. Pillar extraction is practised where possible. In addition to lubrication and inspections, planned maintenance of mining equipment consists of sub-assembly replacements and overhauls. Conveyor and tractor/trailer transport is used underground. but trolley-wire locomotive haulage is being considered. The organization is such that co-ordination is relatively difficult, and certain changes could possibly improve the functioning of the engineering and mining departments. Technical and management training is carried out. Long-term planning will make use of a computer programme and will involve the investigation of other mining methods. Five-year and twelve-month plans are prepared, the planning of coal quality being based on the view that the mine and the power station together constitute a system. Control information systems make use of a remote computer terminal located at the mine. An improved integrated system is being investigated.

Jan 3, 1975

By S. G. Mgenge, J. D. Steenkamp

Tronox Namakwa Sands operates two ilmenite smelters for the production of high-titania slag and low-manganese pig iron. Slag or metal is tapped from one of two product-specific, bi-level tap-holes. In this paper the refractory design specific to the tap-hole refractory layout is described, as well as practices for slag and metal tapping and refractory maintenance. Further developments planned are briefly described.

Jan 1, 2014

By B. K. Cross

This paper, which adopts a philosophical approach, attempts to analyse the contribution that the computer is capable of making in geological analysis, financial evaluation, and mine project control. Also examined are some reasons for non-utilization of these capabilities. As with most computer associated problems, the cause is primarily human and not mechanical. The paper gives one numerical example of the analysis of geological data and one of the evaluation of mine-design data. The values used in the examples are intended only to emphasize certain points and are not necessarily reproducible.

Jan 1, 1980

By J. H. Viljoen, J. F. Morrison, C. H. Wyndham

SYNOPSIS Heart rates, oral temperatures, shovels/min and number of 3/4 ton cars/hour trammed over distances of up to 350 ft were measured in samples of 6-10 miners, engaged in tram-shovelling, at 76°, 84°, 86°, and 89°F wet bulb temperatures in stopes in a mine. From the results it has been concluded that a man with an 'average' maximum oxygen intake capacity of about 2. 8 litres/min should be able to work: at 6 shovels/min, or 30 cars/shift per two men, at 76°-84°F; at 5 shovels/min, or 27 cars/shift per two men, at 86°F; and at 4 shovels/min, or 24 cars/shift per two men, at 89°F wet bulb air temperatures. INTRODUCTION A number of gold mines in South Africa still use tram-shovelling extensively. In this method of rock removal from the face of the stope, Bantu mine workers load rock into cars and tram the cars to a centre gulley where they are emptied. Previous studies from this Laboratory3 have shown that tram-shovelling is one of the most arduous tasks underground. The rate of energy expenditure is relatively high, being an oxygen consumption of about 1.4 litres/min over a period of some hours. In cool air conditions the upper limit to the rate of production of the well-motivated men employed on tram-shovelling has been shown1 to depend upon their capacities for physical work of an endurance nature (as measured by their maximum oxygen intakes). However, in hot conditions the factors which set the upper limit to the rate of production are different. They are primarily the ability of the body to maintain a heat balance between the rate of heat production, due to physical work, and the hot atmosphere, so that the men do not develop excessively high body temperatures8. In order to give mine managers guidance on the 'optimum' rate of production of Bantu mine workers engaged upon tram-shovelling under different temperature conditions underground a study was carried out in a mine. The number of shovels per minute and cars per hour were recorded and heart rates and oral temperatures were measured throughout the duration of the shift on samples of 6-10 Bantu mine workers in different air conditions. The results of the study are recorded in this paper and conclusions are drawn as to the number of shovels per minute and cars per hour which Bantu mine workers of 'average' maximum oxygen intake capacity should be able to produce at wet bulb air temperatures of between 76° and 89°F without either excessive fatigue or danger of heat illness.

By R. Degel

Submerged arc furnaces and electric smelters are applied in numerous metal and slag production lines. Particularly in ferroalloy and non-ferrous metal production, like silicon metal, platinum group metals, calcium carbide, and copper, the units are an essential part of the production technology. Most of these electric furnaces are considered to be highly energy-intensive units. The high level of required electrical power is defined by the process. SMS developed several measures to reduce the overall electrical energy consumption of these metal production lines. In particular, the following measures contributes to a lower energy consumption: improved electrical efficiency with intelligent design and application of components, minimizing the heat losses from the furnaces with a balanced cooling/refractory systems, minimization of process steps (such as elimination of agglomeration), recovery of energy, process optimization (resulting in higher metal yield) and the achievement of higher recovery rates, enlarging furnace capacity to reduce heat losses, and maximizing the power-on time. This paper gives an overview of the above-mentioned solutions.

Jan 1, 2012

By J. L. Gaigher

A simple mineralogical regression model is described, which was devised in order to help the flotation plant cope with rapidly changing headgrades and feed mineralogy. Minerals in the feed were determined by means of quantitative X-ray diffraction and compared with plant performance parameters and flotation reagent consumption rates, using regression analysis. A mineralogical regression model for predicting recovery served to motivate flotation plant personnel and also set standards whereby flotation performance could be measured. The reagent consumption model indicated in which direction any or all of five flotation consumption rates should be altered. All practically measurable parameters, even those showing poor or no correlation, were included in the model, provision being made for the continuous update of a batch of data of 30 lines. Compared with the method of multiple linear regressions, the r2 is poorer at 0,41 (versus 0,50), but the mean standard error of estimate for both methods is identical at ± 6,6 units. The regression model is simpler than the method of multiple linear regressions, and although the accuracy of prediction is not high (41%), the mineralogical regression model proved to be successful in practice. Flotation efficiency, as measured by the mean ratio of head to tails grade, for the 9 month period after the mineralogical regression model was implemented on an hourly basis, improved from 2,8 to 3,2, which is equivalent to an improvement in average flotation recovery of 5% relative.

Jan 1, 1987

"Chairman: Prof A. E. H. BLEKSLEY Rapporteur: Prof J. ELBRONDPanel Members: Prof J. C. Griffiths, Prof T. E. Hawkins, Mr A. C. Langton, Mr M. Splaine, Mr A. WeissThe reasons for failure of computer applications in the mineral industry and the direction of future developments.The Chairman opened the discussion by elaborating on the disappointment felt by some authorities with the lack of progress in the application of computers in the mineral industry during the last ten years, and posed the question to the panel : 'Do you agree that the computer age has not come up to expectations?'Mr Langton said that although there seemed to be a tremendous amount of brainpower applied to the theoretical side, he thought that the production men had not got all the help from computers that could have been given to them. The computer, said Prof Griffiths, is as yet a new tool which should not be used to do old things in old ways. To learn to use the computer will take time. After all, he said, it had taken 400 years after the introduction of the printing press to achieve general literacy, and perhaps it will take 40 years after the introduction of the computer to achieve `numeracy'.In Mr Weiss' view, the reason for the feeling of disappoint¬ment lay in the focussing of attention on the computer. The blame, if any, lay with the people surrounding the computer, that is, the analysts and programmers, to whom the emphasis should be shifted.Prof Hawkins said that he thought that some applications of the computer in the mineral industry had been successful, such as, for example, the compilation of payrolls. Reasons for failures in other areas were to be sought in the fact that the people connected with computers had failed to realise that they were merely part of a system. They had not understood the power structure of the organization which their work tended to change, and were therefore not prepared for the inevitable conflict with the production men.In Mr Splaine's view the production man had not received the assistance he could have had from the computer people because he may possibly not have allowed this to happen.Prof Bleksley concluded from these opinions that the promise which computers had ton years ago had not been fulfilled and added that the opinions expressed by the panel had intruded on his next question which was: 'Is the reason for this that people are involved?Prof Hawkins elaborated on his previous theme, namely, that of computer people in relation to management. Com-puter people, he said, were trying to impose change on management but were not prepared to share the responsibility for these changes. In fact, they wanted their work to be distinct and separate, and, as far as management was concerned, changes would be made when management believed that these would be less agonizing than no change at all."

Jan 1, 2014

By D White, L. Lorenzen

Sampling and metallurgical testwork during various phases of engineering studies is of paramount importance for a robust processing plant design. When developing a process flowsheet, risks in achieving desirable financial outcomes are minimised by ensuring that appropriate sampling and adequate metallurgical testwork support the engineering and cost estimation at each phase of project development. The quality and type of samples used for metallurgical testwork are just as important as the metallurgical testwork itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should consider the spatial orientation, lithology, alteration, degree of oxidation, mineralogy, and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical testwork program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design. The authors have observed that the quality of sampling and quantity of metallurgical testwork carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are based on benchmarks of apparently similar ore bodies or rely on buoyant metal prices supporting cash flows until rectifications can be implemented. The paper will discuss important aspects of sampling and testwork required for engineering studies in designing process plants. Keywords: Sampling, metallurgical testwork, studies, design

Jan 1, 2020

By D. J. Bosman

Rapid fouling of condenser tubes in underground refrigeration plants is a frequent occurrence. It leads to low heat transfer efficiencies, with consequent serious reduction in capacity and increase in the horse-power requirement of the units. High pressures develop in the condensers, and frequent cleaning of the tube bundles is required. The cleaning operation takes up to 8 hours and in some cases results in significant loss of production. One of the possible causes of fouling is deposition of scale, but this can be readily overcome by controlling the concentration of the water. When water evaporates, the dissolved solids remain behind; thus evaporation increases the amount of dissolved solids per unit volume. If half the original volume evaporates, the concentration of the dissolved solids is doubled and the water is said to have a 'concentration' of two. Concentration may be controlled by regulating the amount of water allowed to bleed from the system. The actual concentration value required is a function of the chemical analysis of the circulating cooling water. In one instance, where the problem of scale formation had been eliminated, fouling still persisted, and the possibility of excessive quantities of dust in the re-circulating water was investigated. A dispersing reagent was added to the condenser cooling water as a means of preventing sludge deposition in the condenser tubes. As shown by curve A in Fig. 1 the reagent addition did not decrease the rate of fouling.

The wage structure of graduate White men in 1979, by Adri Kruger, Pretoria, Human Sciences Research Council, 1979.76 pp. R5,00. (Reviewer: D. G. Malan) Financial Times mining international yearbook, edited by WilIiam G. Nightingale. London, Longman, 1980. 750 pp. £24 by surface, £34 by air. (Reviewer: J. D. Austin) Techniques in mineral exploration, by J. H. Reedman. Barking (U.K.), Applied Science Publishers, 1979. 533 pp. $90. (Reviewer: D. L. Kyle) Practical geostatistics, by Isobel Clark. Barking (U.K.), Applied Science Publishers, 1979. 129 pp. £13,75. (Reviewer: D. G. Krige) Uranium: The balance of supply and demand 1978- 1990, by the Uranium Institute. London, Mining Journal Books, 1979. 61 pp. £8,50 by surface,,£9,25 by airmail. (Reviewer: D. J. Crowe) Wear and abrasion in industry The South African Institute of Mining and Metallurgy and the Institution of Metallurgists (South African Branch) is to hold a colloquium on the topic of wear and abrasion of metals in February 1981. Steel rolling The International Conference on Steel Rolling sponsored by The Iron and Steel Institute of Japan will be held in Tokyo, Japan, from 29th September to 4th October, 1980.

Jan 1, 1980

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020