Search Documents

By P. Ramsaywok, G. Legodi

Spiral concentrators are widely used in the coal industry treating fine (-1mm) coal. Their application was a limitation to the product quality until the introduction of low-cut spirals which allow a lower quality ash product to be produced, thus expanding the market. The Exxaro Grootegeluk 1 (GG1) plant has a two-stage traditional rougher-cleaner spiral circuit using conventional SX4 spirals to produce semi-soft coking coal product at 12.5% ash by mass. The overall plant product is 10.3% ash meaning that the coarser sized coal dense medium separation circuits must compensate. A low density cut-point spiral targetting 10.3% ash would thus be beneficial to the overall complex. The spirals were tested in the two-stage plant environment and in a pilot plant. This paper discusses the findings and compares a two stage four-turn low density cut and conventional spiral. The two spiral technologies were unable to sustain a 10.3% ash product. Pilot test work was also conducted on GG1 coal, demonstrating that an eight-turn low density cut-point spiral achieves the targetted 10.3% ash under controlled conditions. Keywords: Spiral, low-cut, coal

Jan 1, 2020

By F. J. N. Bruwer, T. R. Stacey

The research described considers whether the variability in coal material strength, as derived through a series of uniaxial compressive strength (UCS) tests, could be used to indicate the variability in coal pillar strength. The aim is to be able to use a distribution of UCS tests as input into the coal pillar strength calculation. This will allow the pillar design to be expressed in terms of a probability of failure rather than as the commonly used safety factor. To achieve this, the bulk strength factor associated with commonly used pillar strength formulae was replaced with a distribution of UCS results divided by an adjustment factor. The factor was determined so as to ensure that the resulting bulk strength does not deviate from the statistically determined bulk strength published in the original formulae. This approach enabled pillar strength distributions to be obtained using industry-accepted strength formulae, subsequently allowing for a probability of failure to be calculated for a specific pillar design. Using a regional coal material strength curve as a baseline, coalfields in which the coal is stronger than the regional mean can be identified and the pillar designs optimized. This is based on the stronger coals achieving lower probabilities of failure at similar safety factors. The research has considered actual UCS data from multiple mines in the Mpumalanga coalfields of South Africa, and has proved that the variability in material strength between coalfields could allow for some optimization using the proposed approach. Based on the data used in the study, a 2.78% increase in extraction could be achieved. However, further research will be required to validate the results of the study in an underground environment.

May 3, 2023

By N. C. Steenkamp

Lightning has been observed in dust clouds following open-pit blasting. It is proposed that the occurrence of this phenomenon is related to the physical composition and characterization of the mineral fines that comprise the bulk of the dust cloud. Silicate minerals, which are susceptible to fine fracturing during blasting, generate the initial charge. This is further enhanced by collisions and friction during the turbulent upcast in the post-blast dust cloud. Varying size fractions result in different rates at which these particles drop out of suspension and create a secondary temperature gradient. This results in the creation of two charged zones and increases the potential of developing a discharge in the form of lightning. The ideal prevailing meteorological conditions need to be windless to minimize the effect of particle dissipation and have sufficient moisture toenhance the potential of generating lightning.

Apr 14, 2024

By W. Soetaert, P. Dhar, H. R. Kota, M. Thornhill, S. Roelants, I. V. Chernyshova

Yeast-derived bola-amphiphiles have attracted considerable attention for their applications in various industrial sectors in recent years. However, only a few studies on this class of surfactant were reported to be relevant to mineral processing applications. In this paper, one of the novel surfactants, acidic glucolipid obtained from Candida bombicola sophorolipids and modified by using Penicillium decumbens naringinase substrate has been evaluated for its interaction with chalcocite and calcite minerals because of a new Cu-ore Nussir deposit in Norway containing calcite impurity. The interaction of glucolipid biosurfactant with copper sulphide and carbonate minerals was investigated with zeta potential, adsorption and FTIR studies, and also by Hallimond tube and bench scale flotation tests using pure minerals and Nussir copper ore, respectively. The results illustrate collector adsorption and flotation of copper sulfides at neutral pH. The bench-scale flotation results demonstrate that copper sulphides can be selectively floated from carbonate and silicate gangue minerals. This study underlines the glycolipid’s high potential for its use as collector for flotation of valuable copper sulphide minerals. Keywords: Flotation, biosurfactants, adsorption

Jan 1, 2020

By V. Sheikhzadeh, M. R. Sheikhzadeh, A. Haratian, M. Zare

High Pressure Grinding Roll (HPGR) as an efficient grinding technology plays a major role in mineral processing plants. Investigating the effects of this technology on different parts of mineral processing circuits reveals this technology’s capability. In this paper, HPGR grinding effects on an iron ore beneficiation circuit, in comparison with conventional crushing systems were studied. A representative feed sample was taken from an iron ore beneficiation plant, then crushed to minus 6 mm in a laboratory by two methods: HPGR and cone crusher, and finally a concentrate plant circuit was simulated. Plant simulation was performed by doing laboratory tests consisting of grinding, magnetic separation, flotation and filtration on HPGR and cone crusher products, respectively. According to comminution tests results, in particle sizes smaller than 6 mm, a cone crusher product is coarser than an HPGR product. Also, the Bond ball mill work index of the HPGR product was 10% less than the crusher product. Therefore, based on the Bond formula in applying HPGR, ball mill power consumption decreased by 12%. After ball milling to minus 100 microns, magnetic separation tests results showed that the recovery of the cone crusher circuit output was 90.8% and the product Fe grade was 66.4%. For the HPGR circuit these figures were 87.6% and 67.3%, respectively. Therefore, by using an HPGR, a higher Fe grade of the final concentrate was achieved. A flotation test was then performed on the magnetic separation concentrate, where the results showed that the crusher circuit recovery and the sulfur grade of the product were 96.5% and 0.192%, respectively; whereas the HPGR circuit recovery was 97.2% with a sulfur content of 0.185%. Findings revealed that flotation performance in the HPGR circuit was more efficient than the crusher circuit. Vacuum filtration tests on concentrate produced through the HPGR circuit resulted in a moisture content of 12% that was 2% higher than the crusher circuit’s concentrate in the same condition. Keywords: High pressure grinding roll, power consumption, magnetic separation, flotation, filtration

Jan 1, 2020

By P. J. Petit

Changing mining conditions, legislative issues, rising costs, and the constrained supply of skills and electricity in South Africa, have been some of the criteria forcing mine operators and engineers to review the traditional use of compressed air to power underground hand-held drilling operations in narrow-stope, hard-rock mines. In answering the question, 'What is the best way to power this mine?', they have resorted to trade-off studies with results of limited usefulness, because they are site-specific, and use only a few comparative parameters, based on a small data set. This paper aims to provide definitive, objective and quantitative decision-making approaches to evaluate alternative energy delivery systems for stoping in narrow-reef hard rock mines, based on primary and relevant criteria. These include quantifiable criteria such as capital expenditure, operating costs, resulting financial returns, energy and water usage, production performance, life-of-mine, etc. Other important criteria with qualitative aspects are integrated. These are safety, health and environmental concerns, legislative requirements, business risk, technology change, etc. The paper begins with a review of decision making processes available, and proposes the use of the analytical hierarchy process (AHP) method as a multiple-criteria decision making tool and the decision tree-based on milestone-driven uncertainties, to validate the selection of the energy delivery system. The results of a multiple-criteria questionnaire completed by a variety of industry experts and professionals, such as production and operation managers, consultants, suppliers and techno-financial analysts, are discussed. The evaluation indicates the potential for hydropower to be the best solution for narrow reef hard rock mines, based on current information, mine design layout and production.

Jan 1, 2012

By W. Guiye, L. Chongjun, L. Huinan, Z. Yangge, H. Long

The current application of copper-molybdenum (Cu-Mo) separation inhibitors is often associated with large dosage, high toxicity, environmental pollution problems. In order to solve these problems, a light sensitive Cu-Mo separation inhibitor LS（light sensitive inhibitor，abbreviated to LS） was developed. In this paper, inhibitory performance, photodegradation rule, and acting mechanism of LS were studied. The subsequent test results showed that, compared with traditional inhibitors, LS has shown comparative advantages, with lower dosage and good inhibiting effect. A series of flotation tests with LS as inhibitor were conducted on a Cu-Mo concentrate. A locked-cycle test showed that a molybdenum concentrate containing Mo 49.88% and Cu 0.6%, with 93.23% molybdenum recovery and a copper concentrate containing Cu 29.92%, with 99.99% copper recovery can be obtained. The photodegradation performance of the reagent was investigated under 365 nm, 254 nm and sunlight irradiation. The degradation of the reagents could be completely achieved by irradiation of three wavelengths of light. However, with the different wavelength of irradiation light, the degradation rate is different, the time required to reach 50% degradation rate being 3 h (254nm), 4 h (solar light) and 6 h (365nm) respectively. The inhibition mechanism on chalcopyrite was studied. FTIR study showed that LS could be adsorbed on the surface of chalcopyrite by chemical adsorption, which could enhance the hydrophilicity of chalcopyrite. Ultraviolet adsorption tests indicated that the adsorption capacity of LS on chalcopyrite surface was greatly affected by pulp pH value, and the proper pH value was 5-9. Keywords: Copper-molybdenum separation, Inhibitor, Light-sensitive, Photodegradation, Mechanism.

Jan 1, 2020

By C. C. Birch

Due to grade estimation uncertainty, two statistical errors can occur. The Type I error is where material is classified as ore and mined, despite the true value being below the break-even grade. This material is dilution. The Type II error is where the material is estimated to be below the cut-off grade and is classified as waste, although the true grade is actually above the break-even grade. This material is not mined and is lost. The uncertainty was assumed to follow a normal distribution in a previous study. For this study, estimated block values are compared to those determined after mining (the best estimate of the true grade). This actual data from four mines shows that the uncertainty follows a Laplace. There is no single solution regarding adjusting the cut-off grade away from the break-even grade, considering estimation uncertainty, that could be applied to all gold mines. However, adjusting the cut-off grade downwards (up to 22% for one mine) is noted when optimizing the profit considering grade uncertainties. This type of adjustment could open up significant mining areas and extend the life of the mine.

Jul 2, 2022

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant oven, it was essential to ascertain coal cake stability during the loading of a 1 m3 (1 m × 1 m × 1 m) coal cake into the cold pilot-plant oven by a pusher mechanism. Previously established laboratory-scale compaction parameters, to obtain coal cakes with sufficient stability, were employed during the loading tests of the coal cakes. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.It was demonstrated that lower applied compaction forces (14%) can be utilized during 1 m3 compaction, in comparison to laboratory-scale tests, to obtain similar wet cake densities, owing to differences in the effect of frictional forces. Wet cake densities for Waterberg sscc improved slightly (3%) to 1.13 t/m3 when utilizing 79 t/m2 applied force for a 1 m3 coal cake, in comparison to laboratory-scale tests. Similar results were obtained for Oaky North hard coking coal, with a 6% density increase to 1.27 t/m3 at a similar applied force. Porosities decreased by 13% and 32% for Waterberg sscc and Oaky North coal, respectively, when 1 m3 compaction was compared to laboratory-scale tests. An opportunity exists to further decrease the porosities of Waterberg sscc during compaction, whereas acceptable compaction parameters were achieved for Oaky North hard coking coal. Most major vertical cracks and the partial collapse of coal cakes were mitigated, and high-stability coal cakes were obtained that could be successfully loaded into the pilot-plant coke oven by a pusher mechanism.Factors contributing to the instability of the coal cake during loading into the oven, such as vertical cracks, are (i) the cubic geometry (1 m3) of the coal cake, (ii) friction exerted by the oven floor, and (iii) mechanical problems, such as a misalignment between the pusher machine feeder plate and the oven floor. IntroductionOperation of the stamp-charging horizontal 1 t electrically heated coke pilot-plant oven at Exxaro Resources requires coal cake stability during the loading of a 1 m3 compacted coal cake into the oven. In this case, a pusher plate is utilized to push the coal cake into the oven over the oven floor. This is in contrast to a ‘spoon’ or bottom plate feeding mechanism as found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability for the 1 t coke oven, various compaction parameters need to be verified and established."

Apr 1, 2019

By T. Bhambhani, E. Arinaitwe

Solvay has developed several novel reagent innovations to improve separations in sulfide ore flotation and address major industry challenges. These innovations include: a) carbon management strategies to reduce the deleterious impact of organic carbon on flotation circuits; b) new collectors for heavily tarnished or oxidized Cu-Au ores; and c) a functionalized depressant for minimizing penalty elements in metal concentrates. Owing to their unique chemistries, these innovations exhibit a wide spectrum of rather unique properties that are quite in contrast to the traditionally used reagents. The chemistry, attributes, application, and advantages of these innovations are discussed in this paper based on laboratory, pilot, and plant results and observations for various ores

Jan 1, 2023

By C. B. van den Berg

n this study, silver and palladium nanoparticulate inks with different metal-binder ratios were screen-printed onto a paper substrate. The printed layers comprised the metal nanoparticles and an ethylcellulose binder. The layers are not typical metal composites due to the low concentration of binder and high porosity. The electrical sheet resistivity of each particle concentration was measured, and the data fitted using the scaling law of percolation theory and the general effective media (GEM) equation. The percolation parameters, i.e. the percolation threshold and the critical exponent, for each system were determined from the fits and compared. The percolation threshold for the palladium layer (39.8 wt%) was lower than that found for the silver layer (44.9 wt%). The critical exponents determined for the palladium and silver layers were both lower than the universal value for three-dimensional percolation systems. Microscopy observations indicate that the difference in the percolation threshold for the two layers can be attributed to variations in their microstructure.

Jan 1, 2014

By D. D. Howat, J. van der Colf

This paper is the first in a series of three dealing with this subject and also with the rate of oxygen removal from the slags in the presence of solid carbon and with the physicochemical properties of the reduced slags. For selected members of the system, the melting temperatures and primary crystallization products were determined. as were the viscosity and the electrical resistivity of the corresponding melts. All the experiments were conducted in a neutral atmosphere. Where determined, the primary phase was found to be either perovskite or magnesium aluminium titanate. The composition variable exerting the most pronounced influence on viscosity or resistivity was found to be the basicity expressed as the mass ratio (CaO + MgO)jSiO,. The ratio CaOjMgO became important only at Iow basi<:ity values. Although generally there is a direct proportionality between log (viscosity) and log (resistivity), slags h&apos;lving either a very high silica content or a very high titania content have anomalously Iow electrical resistance.

Jan 1, 1979

By Y. Yang, M. Zhang, X. Xia, S Shi, Z. Shen

A stepwise arrangement of flotation cells is the most common layout of a flotation circuit in the mineral processing industry. In such a design, slurry flows from upstream to downstream by means of gravity, and the middling products are returned to previous stages by pumps. This paper will introduce an alternative solution in which the forced-air and slurry-induced flotation cells are adopted so that all the flotation cells can be placed on the same horizontal platform and no pumps will be needed for middling product transferring. The technology of the forced-air and slurry-induced flotation cell will be described in detail, including unique features, the working principle and the related fundamental problems. The comparison of capital investment, operating cost and metallurgical performance will be made between the conventional stepwise arrangement and the samelevel arrangement technology based on industrial practice. Keywords: Forced-air and slurry-induced flotation cell, same-level arrangement, stepwise

Jan 1, 2020

By H. A. D. Kirsten

The structural competence of mesh- and fibre-reinforced shotcrete was investigated in two series of tests on full-scale panels. It was found that uniformly distributed loading was marginally less demanding than point loading, mesh reinforcement was superior to fibre reinforcement, Dramix fibre and Melt Extract fibre were similar in reinforcing characteristics, and 30 mm to 35 mm was an optimum fibre length. Furthermore, the consistency of the fibre content could not be assured on practical mining sites, and an average fibre content of about 1,5 per cent was the maximum that could be obtained for fibre lengths not exceeding 35 mm. Also, owing to its greater flexibility, shotcrete reinforced with diamond mesh was preferable to fibre-reinforced shotcrete in mining excavations subject to squeezing conditions. In view of the difficulties associated with assuring the consistency of the fibre content in mining applications, it appears that the sophisticated attributes of fibre-reinforced shotcrete can be effectively exploited only in civil-engineering applications in which quality assurance is subject to explicit contractual control. Load-deflection curves, together with measurements of compressive stresses in the surfaces of some of the panels, enabled the ultimate flexural strength of reinforced shotcrete to be rigorously formulated, and rigorous design procedures for shotcrete subject to bending and direct thrust to be developed. The application of the procedures is demonstrated in a practical design case in which the moments and thrusts in a tunnel lining are determined in a numerical analysis of the interaction between the lining, the surrounding rock, and the rock-reinforcing system.

Jan 1, 1992

By N. Hadebe, A. Mampuru, F. Jantjies

Mintek conducted test work to study the effect of media wear when using Mintek’s Milling-in-raffinate technology. The grinding media consisted of high-chrome and ceramic balls. The tests were conducted using a laboratory 5L 316 stainless-steel rubber-lined mill. Magotteaux supplied the high-chrome and ceramic balls. The raffinate was synthetically prepared using a typical Cu/Co (2.2 g/L Cu, 3 g/L Co) composition. The milling rate, media wear, mill, leach extraction efficiencies, gangue acid consumption, and residence time were studied. The tests indicated that the high-chrome balls had a higher corrosion rate than the ceramic balls. The ceramic corrosion rate was lower than 0.1 mm/y. The highchrome balls performed better during the leach stages with faster milling time, higher leaching efficiencies for both Cu and Co, lower gangue-acid consumption, and lower residence time

Jan 1, 2023

By A. Angelov, U. Peukerd, S. Gaydardzhieve, A. Stefanov, K. Grossman, V. Stoilov

Flotation concentrate originating from the Asarel-Medet porphyry copper mining and processing complex in Bulgaria has been subjected to regrinding using a Ro-Star mill; the effects of which on the downstream metallurgical behaviour are discussed. Particularly the effect on the liberation degree was studied through an optical microscopy and MLA-SEM automated mineralogy. On the other hand, copper selective flotation of the reground bulk concentrate was realised to evaluate the anticipated metallurgical improvement. Process parameters such as involvement of prior hydrocycloning and variation of collector dosage have been evaluated. Within a two-minute residence time inside the Ro-Star mill, an improved liberation degree of the copper bearing minerals has been observed. As a consequence, enhanced copper recovery and selectivity against pyrite was noted. It has been found that in order to guarantee efficient flotation of the resulting ultrafine particles, a modified flotation regime (i.e. changing collector suite and dosages) should be followed. Keywords: RoStar Mill, liberation, flotation recovery, ultrafine particles

Jan 1, 2020

By O. A. Olaseinde

The 2101 lean duplex stainless steel has wide potential application in storage, heat exchangers, and in the oil and gas industries. This work investigates the electrochemical behaviour of 2101 duplex stainless steel with an addition of 0.15 wt% ruthenium, using potentiodynamic techniques in 1M H2SO4 at 25º, 40º, 60º, and 80ºC. The microstructures of samples were characterized using optical metallography and scanning electron microscopy. The results showed that the ruthenium addition moved the corrosion potential of alloy 2101 to a more positive potential. All samples containing ruthenium displayed longer passive regions at 25°C and 80°C compared to those without ruthenium. Alloys without ruthenium had higher critical current density (icrit) values when compared to the alloys with ruthenium. Ruthenium additions decreased the passive current densities and inhibited anodic dissolution. At room temperature the corrosion rate of alloys with ruthenium was lower than these without ruthenium.

Jan 1, 2012

By J. Hadjigeorgiou, Y. Potvin

In a benchmarking paper published in the SAIMM Journal, Potvin and Hadjigeorgiou (2008) reviewed ground control strategies to manage large deformations in underground hard rock mines. Significant differences were identified in the design and acceptable tolerance between civil and mining engineering practice for squeezing ground conditions. Variations were also noted in ground support strategies between Australian and Canadian mines. In this paper we review progress in design methodology and ground support practice since 2008, including the availability of more effective deformation monitoring, new design tools, greater access to yielding ground support elements, and better installation practices. An improved understanding of technical and practical issues associated with squeezing conditions has led to the development of ground support guidelines for a range of squeezing ground conditions in hard rock mines.

Jul 5, 2023