Search Documents

By L. H. Banning

The Bureau of Mines conducted pioneering batch and laboratory cyclic tests that simulated plant operation in developing a procedure for acidulating phosphate rock with fluosilicic acid. Both high-grade deslimed phosphate rock and low-grade phosphate rock samples were treated. The most promising results were obtained by acidulating des limed high-grade material. In a series of seven cyclic tests, 85.4 percent of the P20S was recovered in solutions. The average P2O5 content of the phosphoric acid-monocalcium phosphate solutions of the first step was 156 grams per liter, and the average fluorine content was 4.7 grams per liter. Residues had an average fluorine content of 30.7 percent and contained 83.9 percent of the total fluorine in the charge materials. Some fluorine was lost by volatilization.

Jan 1, 1975

By Elizabeth A. Johnson

The effect of slag composition on lead losses to slags and on the behavior of associated accessory elements in lead blast furnace smelting has been studied by the Bureau of Mines. Equilibrations of 30 g of lead and synthetic slag doped with Cu, In, TI, and Sb at 1,200° C in CO-C02 atmospheres revealed the importance of the FeO:Si02 ratio and the basicity ratio, (CaO+MgO):SiO2, of the slag. Lead losses to slags increased with an increasing FeO:Si02 ratio and decreased with an in-creasing basicity ratio. Copper and indium distribution coefficients, [Lx =] increased from 15 at the lower basicity ratios to near 60 at higher basicity ratios. LTI values increased from 20 to 150 as slag basicity increased. Lcu, Lin, and LTI were relatively in-dependent of the FeO:Si02 ratio, but increased with greater amounts of accessory elements in the system. Antimony distribution alone was shown to be strongly affected by FeO:Si02 ratio, although data were scattered. LSb values ranged from 20 to 800 and decreased sharply with increasing FeO:Si02 ratios. The basicity ratio and the level of accessory element load did not have any noticeable effect on LSb.

Jan 1, 1983

By H. H. Schrenk, L. B. Berger, Robert L. Beatty

"INTRODUCTION Toxic oxides of nitrogen 5/ are formed or liberated in many industrial process and may constitute a definite hazard to the health of persons exposed to the atmospheres thus produced. Oxides of nitrogen occur in the gases involved in the use of explosives, in the gasoline products of welding operations in the exhaust of internal-combustion engines, in the vicinity of electrical discharges, in the combustion of nitrated materials, and in chemical process involving nitration or the use of nitric acid, Itis evident that oxides of nitrogen may constitute an occupational hazard in many industries, and therefore it is important that those concerned with the control of such hazards be equipped with a technique suitable for the determinations of oxides of nitrogen in the concentrations of,hygienic significance."

Feb 1, 1943

By G. B. Atkinson

The Bureau of Mines, in cooperation with McDermitt Mine, investigated a method for recovering mercury metal from mercury sulfide flotation concentrate by a hydrometallurgical technique. This preliminary report shows the feasibility of leaching mercury with a cupric chloride solution and electrowinning mercury from the solution. Proposed chemical reactions are shown in equations 1 through 3: 2CuC12 + HgS + 2CuCl + HgC12 + S°; (1) electrolysis HgC12 ?Hg + C12; (2) 2CuC1 + C12 ? 2CuC12. (3) A bench-scale leaching-electrowinning apparatus capable of treating 2.36 kg of sulfide concentrate in 11 days was operated continuously. An acid chloride solution containing, in grams per liter, 70 Ca, 60 Cu, 30 Fe, and 80 Hg was used as both leachant and electrolyte; 99.5 pct of the mercury was solubilized from the sulfide concentrate. Electrolysis of the leaching solution recovered mercury metal at an average current efficiency of 32 pct and an average energy consumption of 1.2 kwhr/lb Hg. Results from a preliminary economic evaluation indicated that a plant producing 31,500 flasks of mercury per year would have a capital cost of $3.7 million and an operating cost of $62 per flask of mercury.

Jan 1, 1983

By Wm. C. Dean

The location of trapped miners from their seismic signals will be in- accurate if we assume the P-wave propagation velocity is a constant. P- wave velocities are anything but constant in regions about mines, so some calibration is necessary to obtain more accurate seismic locations. The reference event method compares the time arrivals of signals generated by the miners with those previously recorded from a reference or calibration event in the vicinity of the miners. This method locates the miners' position relative to the calibration source. Hence, the location of the miners is absolute if the reference event position is known absolutely, usually from surveys and mine maps. Advantages resulting from the system, besides greater accuracy, are locations independent of the velocity model assumed, the same solution from the full array and from any subset of four or more seismometers in the array (three if the miners' depth is known), fewer seismometers required, and no complex computers required for analysis. VELA Uniform experience shows that the accuracy of locations of teleseismic explosions and earthquakes is improved by an order of magnitude over locations computed from average travel time curves. Each calibration event is applicable only over a limited range. We recommend a field test of the method at a mine to measure its location accuracy, the range of effectiveness for each calibration event, the number of seismometers needed, and the number of reference events required per mine. From these experiments we could decide whether the reference event method was useful and, if so, what form a practical rescue system would take.

Jan 1, 1974

By Joseph P. DuCarme

The U.S. Bureau of Mines explored new methods and technology for extracting coal from the Appalachian Mountain region of the Eastern United States. These methods were aimed at extracting coal from thin seams and focused on the use of "roof-fall-tolerant" (RFT) mining concepts. These methods could be used on existing, abandoned highwalls or in conjunction with new highwall mining. The research was conducted using small-scale and quasi-full-scale physical models to obtain experimental results. Details are provided on (1) the quasi-full-scale model for cross-ridge mining, (2) the quasi-full-scale model for down-ridge mining, (3) the test results of these models, and (4) recommendations for future research. Significant results include demonstration of the RFT concept, a discussion of expected coal produced from these methods, and recommendations for future research.

Jan 1, 2010

By David K. Ingram

The development of large open surface fractures over mined-out coal longwall panels is the focus of this U.S. Bureau of Mines report. The research concentrates on defining the fractures characteristics and their controlling variables. The investigation was conducted at two mines in south-central West Virginia. All but one of the fractures are subparallel to the trend of the underlying longwall panel. One fracture is perpendicular to the trend of a longwall panel. Overall length of the fractures ranges from 60 to 900 ft. In cross section they are V-shaped, ranging from a couple of inches to 25 ft in width at the surface, but narrowing as they increase in depth. Fracture depth varies from a few inches to over 50 ft into bedrock. A vertical fracture or joint plane was observed in the bedrock at several open zones along the fractures. All of the fractures vary in elevation and do not parallel surface contours. The fractures are aligned with local joint trends, they correlate with longwall development, and they are situated in an increased tensional area over the mined out longwall panels. These observations indicate that the fractures are tensional openings along preexisting joint planes possibly triggered by longwall mining.

Jan 1, 1989

By R. V. Ramani, V. T. Burgos, J. A. McClay

General The underground mining environment has traditionally been hostile and as early mines were developed, coal seams with particularly difficult natural conditions were bypassed in favor of those more easily exploited. Barring the discovery of new and novel sources of energy, the depletion of petroleum and natural gas reserves will eventually force the United States back to the use of coal as its primary energy source. Figure 1 illustrates the trend away from coal which has taken place over the past half century. Today, the demand for coal requires a re-evaluation of all coal seams to meet the needs of the energy market. Difficult mining conditions may result in an increase in the consumption of roof control materials, require greater investment in pumping and ventilation systems, and increase the need for in-depth engineering of far greater safety in production plans. They may also cause delays in mine development and curtail production, all of which combine to drive up the unit production cost. It is reasonable to expect that conditions will continue to deteriorate as current reserves are depleted, thus bringing this factor into greater prominence in the future. For several years now, it has become apparent that in addition to economic objectives, coal companies must set and achieve several concomitant objectives to accomodate society's interest in the conservation of natural resources. Government action to meet this interest has taken the form of two categories of Federal legislation, environmental protection and employee health and safety. The effects of both of these have not been fully evaluated with respect to the total economic picture, although preliminary evidence indicates that an immediate increase in

Jan 1, 1975

By Linneas W. Laage

Coal production from underground coal mines has been important to the development of the industrial economy of the United States. Environmental problems have developed from some abandoned operations. These problems include: mine and refuse pile drainage, subsidence, unsafe mine openings and to a lesser extent mine gases, slope stabilities, mine and refuse pile fires and abandoned equipment and structures. Field investigations in three eastern coal mining districts, two in Ohio and one in Illinois, were performed to document the mine closure procedures used and subsequent problems that developed. The purpose was to identify, evaluate, and rank the seriousness of these problems. Based upon this evaluation, the undesirable present day situations could have been avoided or at least minimized by varying certain mining practices or mine closure procedures. It was found that federal regulations address all of these problems during the pre mining, active mining and post mining phases except for abandoned equipment which is the least threatening problem category. Ideally current practice would prevent future problems. However, the extensive and complicated nature of the legislation, environment and mining practices will necessitate adjustments to the law. The investigator recommends the following: 1) Goal oriented legislation encouraging complete resource extraction, standardization and compilation of mining generated hydrological data, periodic review of the coal mining regulations, and improved communication and cooperation between coal interests, regulators and the public. 2) Permitting effluent limitations to accurately reflect natural conditions. 3) Solidly back filling shafts and individual assessment of sealing or capping requirements. 4) Installing shaft vent pipes into the fill material to intercept and vent methane.

Jan 1, 1982

By Manuel Gomez

Areal distributions for ash, total sulfur, and sulfur forms were developed for the top 12 inches, the middle section, the bottom 8 inches, and the total seam of Pittsburgh coal in southwestern Pennsylvania. The sulfur and ash exhibit an apparent high local variability. As a general rule, both the sulfur and ash show high concentrations in the top 12 inches and in the bottom 8 inches of the seam relative to the concentrations observed in the middle section of the seam. The high-low sulfur and ash concentrations in the top 12 inches of the seam are not coincident with the high-low sulfur and ash concentrations in either the middle section or the bottom 8 inches of the seam. With respect to sulfur and ash, it is suggested that the top and bottom sections of the Pittsburgh coal may reflect both a syngenetic and epigenetic origin. Present data support the belief that paleotopography controlled Pittsburgh seam deposition. Evidence is presented to show that channels were cut at various times into the semilithified sediments that buried the Pittsburgh seam. In this channeling process, portions of the Pittsburgh coal may have been eroded away. Following channel development, the lower part of the Pittsburgh sandstone filled the complex system of braided channels to produce the "want areas" encountered in present mining operations. In localized areas of the Pittsburgh seam, impingement of Pittsburgh sandstone may be responsible for the lateral displacement of the coal. Information of this type becomes important in the assessment of exploration data, in the development of a quality control system for mine output, and in mine life planning.

Jan 1, 1974

Coal is found in the northeast comer of Georgia, in Dade, Chattooga, Walker, and Floyd Counties. Five seams, which underlie all of Lookout, Sand, and Pigeon Mountains, have produced most of the coal mined in the state. Representative analyses of Georgia coals show that they are typically low sulfur (less than one to one percent), low-to-medium volatile, bituminous deposits. Although there is no active mining in the state, reclamation continues on several permitted areas. In 1983 the State of Georgia relinquished primacy to the Office of Surface Mining. Since that time permits have been issued and mining completed. All the sites are presently in the process of bond release.

Jan 1, 1992

By Janke L. W. Jolly

Owing to an upsurge in export earnings. Cameroon made substantial economic Progress in 1978 and 1979. With a real growth estimated at 6%, the gross domestic product (GDP) for 1979 surpassed $5 billion.2 Crude petroleum production was providing a new potential in 1978 and 1979 for achieving national self-sufficiency. Among other benefits, crude petroleum exports were helping to offset the escalating costs of refined petroleum imports and to reduce the 14% to 17% annual rate of inflation. Over the 4 years prior to 1978, Cameroon's petroleum imports increased by 12.1% in volume annually, while the import cost increased by 24.5% annually to about $105 million. Total export earnings for 1978 were $805 million,3 to which crude petroleum contributed $25.3 million and crude aluminum product exports contributed $25.9 million. Petroleum exports had increased to about $240 million in 1979 and were in third place after coffee and cacao. Total imports for 1978 were valued at nearly $1 billion. The volume of petroleum imports decreased in 1979 to 552,000 tons, compared with 622,000 tons in 1978. The European Economic Community (EEC) countries purchased over 75% of total Cameroonian exports and provided most of the Nation's imports. The United States purchased $12.4 million in petroleum exports from Cameroon in 1978. Domestic consumption of aluminum metal from imported Guinean alumina continued. to grow; thus exports of this metal to France (valued at $2 million in 1978) and Japan

Jan 1, 1981

Develop a simple and practical technique to measure in situ rock mass properties for realistic design and stability evaluation of underground structures. Background The Bureau of Mines has developed basic principles and techniques to determine in situ rock mass properties including Poisson's ratio, deformation modulus, and yield and failure strengths. An instrumentation package consisting of three pressure cells is installed in a single drill hole. Cell pressure response data are acquired and used to calculate and determine the rock mass properties. How It Works A test hole of BX size (approximately 5.7 cm) or larger is drilled to the approximate depth of the measuring point. The last portion of the test hole is drilled with precision bits to EX size (approximately 3.8 cm). The instrumentation package, which consists of one 3.8-cm-diameter cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated, flat borehole pressure cells (BPC's), is then installed. A complete history of cell response to changing strata loads is acquired on a continuous basis with a chart-type hydraulic pressure recorder. From these cell pressure data, Poisson's ratios, deformation moduli, and yield and failure strengths are calculated and determined.

Jan 1, 1990

By R. V. Ramani, A. S. C. Owili-eger

A mass balance equation can be written for the unit block of Figure 7 for changes within the volume during time At as: [ ] where x and y are the coordinates; q is the flow across any surface; p is the density of the fluid flowing through the medium; qvol is the volumetric flowrate; @ is the medium porosity; and Ax and Ay are the dimensions of the block. The subscripts t and (t+At) denote time levels and At is the change in time. Writing this equation in nota- tional form and on rearranging, the following expression is obtained:

Jan 1, 1974

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 241,502 employees worked in surface mining locations in 2003, corresponding to 212,113 full-time equivalent (FTE) workers. • Surface employees accounted for 84.6% of all mining employees. • The majority of surface employees (73.7%; n = 177,927) were mine operator employees as opposed to contractor employees. • Stone operator employees comprised the greatest percentage (27.2%; n = 65,743) of surface employees.

Feb 1, 2005

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1978 and 1979 was 8831.8 million and $336.4 million, respectively. In 1978, nearly all commodities registered an increase in production and value; unit value increased for all commodities, with the exception of native asphalt and sand and gravel. Alabama led the Nation in the production of crushed marble and was second in bauxite, third in masonry cement, kaolin, native asphalt, and oyster shell, and fourth in bentonite, dimension marble, fire clay, and scrap mica. Trend; and Developments.-The Alabama State Docks at the Port of Mobile handled more than 10 million tons of bulk material in fiscal year 1978; volume dropped slightly to 9.8 million tons in fiscal 1979. Bulk materials comprise the major activity at the facility, with iron ore and bauxite being two of the major materials handled. The movement of these ores is vital to the operation of many heavy industries in the State.

Jan 1, 1981

By D. S. Kingery, F. F. Kopsch

The practice of using two or more main ventilating fans is common at large coal mines throughout the coal-mining industry. To assure adequate and efficient ventilation at may mines, such multiple-fan systems are necessary. The hazards associated with interrelated ventilating currents if a fan fails are controversial, and to date little effort has been made to study this specific problem and to determine corrective measures. The obvious questions are: 1. Is there a hazard? 2. Under what circumtances does it exist? 3. How serious is it? 4. What are corrective measures? Most members of the mining fraternity agree that reduced quantities of air and changed airflow patterns introduce potential hazards, especially where gaseous conditions exist when mechanized methods are used in concentrated mining 0 The seriousness of the hazard depends on the ease with which methane accumlates in face areas or haulage roads, the quantity of methane in workedout areas, and the extent to which reversed air currents interfere with escape and recovery operations after mine fires or explosions. These studies cover three mines and give the distribution of air for the specific conditions show. Each mine probably has somewhat different airflowpressure relationships between fans. This depends on the number of fans, the

Jun 1, 1959

By W. A. Jacob, E. W. Dean

The Pittsburgh petroleum laboratory of the Bureau of lines has recently developed an improved method for the determination of water in pctroleum emulsions. It has been described in detail in an article entitled "A convenient method for the determination of water in petroloum and other organic emulsions" by E. W. Dean and D. D. Stark (Jour. Ind., and Enc. Chem. Vol. 12, ſay, 1920, page 436). It is essentially a modification of the familiar procedure of "distillation with an iniscible solvent", the improvement consisting in the use of apparatus that is rºck more convenient than any previously employed. The method has been used with marked success in the Bureau's laboratories for a period of about a year and has also been tried with equal satisfaction by a number of other laboratories. It has been most extensively employed for determining the water content of heavy fuel oils but has been applied also to several other types of emulsions, including shale oils, tars derived from coal, greases, and mixtures of powdered coal, oil and water. The Bureau has received a number of requests for information regarding commercial sources for the apparatus used, and having been assured of the value of the method, has taken steps to render it available for general use. - The equipment is, with the exception of two items, made of parts that are obtainable from the ordinary stock of chemical supply houses. The two exceptions are (1) the so-called "distilling tube receiver" and (2) the electric heater. The former is an essential part of the equipment; the latter is a convenient ac cessory but it can if necessary be roplaced by a gas burner. Efforts on the part of the Bureau staff to ronder these two items of apparatus available for purchase from supply houses, or for production by the user are hero described.

Sep 1, 1920

By Mark Colwell, Russell Frith

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coal fields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwallface. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 5, 1999

By R. Karl Zipf, Z. T. Bieniawski

"A set of fracture profile photomicrographs is presented for fractures generated under mixed mode loading of the Pittsburgh coal. The fractal dimension is used· to characterize the irregularity of these profiles and a tentative relationship is presented between the fractal dimension and the fracture toughness. Surface roughness appears to depend solely on the stress intensity and no other dependence was observed with fracture loading mode, loading rate· or specimen orientation. Observations of crack bifurcations.in fracture profiles can indicate crack growth direction whereas direct surface observations generally cannot in materials such as rock and coal.1 INTRODUCTIONThe production of fine fragments of material as a result of some loading event occurs in many industrial processes. In crushing and grinding, the efficient production of fine fragments is the desired end result; .however, in coal cutting, the production of fine fragments may lead to high levels of respirable dust in the immediate atmosphere with the danger of human lung diseases. Two of the most important sources of fragments in the 1 to 10 micron size range during a cutting process are 1) severe crushing in a zone near the loading tool and 2) subsequent shearing along major crack surfaces that form the larger fragments during material reduction. These and other sources of fine fragments generation are discussed by Roepke (1984) and Zipf and Bieniawski (1986). The physical character of the nearly created major crack surfaces is believed to have a strong influence on the amount of fine fragment generation that occurs during subsequent shearing movement. When the major large fragments initially form, they are ""locked"" in place by the irregular character of the new fracture surface. Only after some relative motion has occurred between fragments are they actually liberated, and the net result is the formation of additional fine fragments. The fine fragmentation is not necessarily limited to the shearing of high points from the macrocrack surf ace since material remaining in the wake of the crack tip is damaged to a substantial depth below the actual crack surface."

Aug 31, 1989