Search Documents

By R. V. Ramani, S. Shankar

"The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies.A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec.Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg!m3 (standard deviation= 0.03 mg/m3)from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0.10 mg/m3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. Jr was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed.Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining."

Dec 1, 1996

By M. I. Copeland

The investigation of the zirconium-gadolinium equilibrium diagram was part of a program to investigate rare:earth alloys for use as nuclear reactor control materials. Investigation of the zirconium-gadolinium equilibrium diagram revealed a eutectic system with limited terminal solubilities and one peritectoid reaction. The eutectic composition occurs at about 82 percent gadolinium, and the eutectic isotherm, which occurs at 1,220 ±5° C., extends from about 12 to 99+ percent gadolinium. A peritectoid isotherm occurs at 890 ±5° C. and extends from about 2 to 99+ percent gadolinium. The solubility of gadolinium in beta zirconium decreases from about 12 percent at 1,220 ±5° C. to about 2 percent at 890 ±5° C. The solubility of gadolinium in alpha zirconium decreases from approximately 5 percent at 890 ±5° C. to between 2 and 3 percent at 600° C. Vary little solubility of zirconium in gadolinium was indicated. An allotropic transformation of gadolinium was observed at 1,260 ±5° C. A change of the gadolinium transformation temperature on alloying with zirconium was not observed.

Jan 1, 1961

As part of the Bureau of Mines subactivity in secondary resource recovery and to expand the Nation's mineral base, the Tuscaloosa Research Center made characterization and preliminary beneficiation studies of the waste residues from various coal-conversion processes: from pilot plant tests of the Synthane process for coal gasification, the Synthoil process for coal liquefaction, and the solvent-refined coal (SRC) process for sulfur removal from coal. Those coal conversion processes selected for this study were based on the availability of pilot plant samples. Physical, chemical, and mineralogical examinations of the wastes made to determine the mineral content prior to physical beneficiation tests indicated that in addition to significant quantities of carbon, some trace elements offer potential for concentration.

Jan 1, 1980

By G. E. McClelland

The Bureau of Mines investigated chemical methods for producing high- purity gold from precious-metal-bearing zinc precipitates and steel wool cathodes. Precious-metal-bearing zinc precipitates and steel wool cathodes are unrefined products from conventional cyanidation and heap leaching-cyanidation operations. The zinc precipitates contained 14,40 pct Au and 0.35 pct Ag. The precious-metal-bearing steel wool cathodes contained 20.65 pct Au and 4.84 pct Ag. The precipitates and cathodes were treated with dilute acid to solubilize the silver and/or base metals. The gold-bearing residue was leached in dilute aqua reqia to solubilize the gold. High-purity gold was precipitated from the aqua regia solution with oxalic acid, sulfurous acid, sodium bisulfite, and gaseous sulfur dioxide. The leaching-precipitation experiments recovered 99.9 pct of the gold. The gold precipitates ranged in fineness from 997 to 999 fine. The chemical refining method provides a viable technique for the smaller operator to produce high-purity gold without using pyrometallurgical refining methods.

Jan 1, 1985

By E. J. Gleim

Contact with trolley wire in the mines of the United States has taken a considerable toll of life throughout the years that trolley locomotives have been employed as a means of' transportation. A study3/ of the records over a 15-year period for one State alone showed that, of 98 fatalities resulting from contacts with electrical circuits and equipment, 75 were caused by direct or indirect contact with unguarded trolley wire in coal mines. The law relating to guarding trolley wires in the mines of this particular State, as amended in 1935, reads in part as follows: "All trolley wires carrying 220 volts or more, and less than six feet six inches above top of rail, must be guarded at all points under which men and animals are required to pass***,'" The natural conclusion to be drawn from such records is that lack' of guards or shields must be held responsible for these fatalities. As a preventive measure, it has been advocated that every foot of trolley wire in mines should be guarded. Although some such drastic steps may appear to be amply justified, closer examination of the records nor this and other coal-mining States shows that absence of guards is not entirely responsible; but rather that other factors, such as carelessness and neglect it the observance of certain well-established simple rules concerning installation and location of trolley wires, also are responsible. In other words, if trolley wire is installed carelessly and its maintenance is neglected, it should not be expected that the mere installation of guards will overcome such carelessness and neglect. This publication discusses Various types of guards that have been used in Coal and metal mines of this country, together with related steps bearing upon the problem of 'preventing shock and fatalities from contacts with trolley wire. The material herein contained is taken largely from Information Circular 6577,4/ now out of print, and has been revised to include some types of guards that have been used in metal mines, together with a discussion of guard materials not covered in that publication.

Jan 1, 1945

By Jerry E. Olson

In 1986, at the request Of the Bureau of Land Management, the U.S. Bureau of Mines studied the central portion, encompassing 20,727 acres of the 32,261-acre Badlands Wilderness Study Area (OR-005-021) in order to evaluate its identified mineral resources. The study area is located in Crook and Deschutes Counties, OR, about 12 miles east from Bend. No mineral resources were identified. The area studied is underlain by Tertiary and Quaternary basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, or mineralized areas occur within or near the study area, but some sand and gravel has been removed from alluvial deposits at the east and west sides of the area. Slab lava of marketable grade and quantity was not found in the study area. None of the study area is of current interest for geothermal resources, but the eastern third of the wilderness study area is leased (1984) for oil and gas.

Jan 1, 1987

The Sago Mine Disaster, on January 2, 2006, placed renewed focus on several different aspects of safety in the underground coal mining industry. One area which received increased attention since Sago and other underground coal mining events is the concept of Safety Culture. This report describes the results of a pilot Safety Culture Assessment implemented at a small Appalachian underground coal mine, hereafter referred to as the Mine. The purposes of this pilot assessment were to (a) evaluate the feasibility and usefulness of a methodology for assessing safety culture that had previously been developed for use within other industries, (b) to initiate an investigation into the understanding and defining of the existing safety culture of the underground coal mining industry, and (c) provide meaningful and useful recommendations for the participating mine for their consideration in their ongoing quest to enhance their existing safety culture. This pilot assessment was conducted in July 2007. The report provides information regarding the presence or absence of safety culture characteristics within the Mine. Observations regarding the characteristics of the Mine?s safety culture that should be sustained are presented. Areas in need of attention and management focus to improve the Mine?s safety culture are presented as well as recommendations for moving forward. Safety culture characteristics that are important for the existence of a positive safety culture have been identified to include: - Safety is a clearly recognized value in the organization. - Accountability for safety in the organization is clear. - Safety is integrated into all activities in the organization. - A safety leadership process exists in the organization. - Safety culture is learning driven in the organization. - A process for establishing a strong and effective Safety Conscious Work Environment (SCWE) is in place. Performance objectives are associated with each of the safety culture characteristics and particular behaviors and attitudes have been identified that can be measured to evaluate these objectives. Using a methodology originally developed with the support of the U.S. Nuclear Regulatory Commission, an assessment of selected organizational behaviors and attitudes was conducted to evaluate the Mine in terms of these safety culture characteristics and their associated performance objectives. The methodology involves obtaining a variety of quantitative and qualitative information, using multiple data-gathering methods. The information collected is largely based upon the perceptions of the individuals in the organization. The evaluation is a ?point in time? snapshot of the Mine, but cultural beliefs and assumptions do not change quickly. The feasibility and usefulness of the methodology was successfully demonstrated during this pilot assessment. All aspects of the methodology including functional analysis, structured interviews with accompanying behavioral scales, work observations, and the paper and pencil

Aug 1, 2007

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By M. J. Reasor, J. M. Antonini, L. Wu, K. Van Dyke, Z. Ye

The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and· laboratory animals. Currently, no effective treatment exists for workers who may have been exposed to the inhalation of silica. The objective of this study was to develop an animal model in which we could evaluate the effect that anti-inflammatory steroids have on the acute silica-induced pulmonary inflammatory response. Male Fischer 344 rats were pretreated with either dexamethasone (2 mg/kg) or saline vehicle (i.p.) on days 1, 3, and 5. On day 6, the animals from the two groups were then intratracheally instilled with either silica (20 mg/0.5 ml saline vehicle) or saline vehicle (0.5 ml). Twenty-four hours after the instillations in the non-steroid group, significant increases occurred in total protein, total number of cells, neutrophils, and lymphocytes recovered from the lungs of animals treated with silica compared to saline controls. Silica also caused dramatic increases in the luminol-dependent chemiluminescence (LDCL) of lung tissue and bronchoalveolar lavage (BAL) cells. The LDCL reaction was markedly decreased by either superoxide dismutase (SOD) or N-nitro-L-arginine methyl ester hydrochloride (L-NAME). SOD is involved in the enzymatic breakdown of superoxide anion, while L-NAME, a nitric oxide (NO) synthase inhibitor, prevents the formation of NO. When the superoxide anion and NO react, they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent which may be involved in the silica-induced oxidant lung injury. When the animals were pretreated with the steroid dexamethasone, there was a complete protection against the biochemical, cellular, and chemiluminescent indices of damage caused by silica. The mechanism in which the steroid protects the lung from damage may be due to the ability of dexamethasone to block the induction of NO synthase. With further study in animals, the anti-inflammatory steroids may be useful in the treatment of silicainduced lung injury.

Dec 1, 1995

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By Deborah A. Spotts

Researchers at the Bureau of Mines have developed a technique for re- generating chromic acid-sulfuric acid etching solutions used in metal surface treatment operations. The technique utilizes a diaphragm cell equipped with a cation-selective membrane to oxidize cr3+ to cr6+ at the anode and to remove copper, the major metallic contaminant, at the cathode. Normally, spent etchant is discarded after approximately 3 days of use. Using the electrolytic cell, the etchant can be used for a year without replacement, From data obtained from industrial-scale cells, the installation of a regeneration cell with a 1,000-gal catholyte- holding tank has been estimated to save at least $240 per day, The payback period for the investment is estimated to be about 10 mo or less. Because the magnitude of these cost savings will vary at different locations, several graphs are presented to aid in calculating payback for a specific site. Using these graphs and the capital costs presented in this study, the payback period can be determined for installing a regeneration cell with a 500- or a 1,000-gal catholyte-holding tank in an existing surface treatment plant.

Jan 1, 1983

By John H. Soulé

"INTRODUCTION Spodumene and lepidolite were shipped from the Harding pegmatite deposit, Taos County, N. Mex., in the period from 1930 to 1930. Tantalum minerals were noted as early as 1924 and described in 1931 3/ but no tantalum ore was shipped until 1942. The deposit was mapped and studied by geologists of the Federal Geological Survey and engineers of the Bureau of Mines late in 1942 and early in 1943, and a Bureau of Minus exploratory project was carried out in 1943. 4/ Thu following report presents the results of that project.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Minos has as its primary objective the more effective utilization of our mineral resources to the end that they make the greates possible contribution to national security and economy. It i the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lovell B. Moor, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallugiical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, Assistant Director."

Dec 1, 1946

By R. V. Ramani

"The importance of adequate mine ventilation for good health and safety conditions has been recognized since miners first ventured underground. All over the world, governmental actions on mine health and safety arc directly connected with mine atmospheric environments their assessment and control. These governmental actions have been, and continue to be, motivated by the repeated experience that potential threats from inadequate control can evolve, either suddenly or in the long-term, into unpleasant reality, with catastrophic health and safety consequences. These governmental actions arc also an indication of the remarkable professional progress being made in the field of mine ventilation.Surely, no developed country allows underground mines to operate without strong measures for the control of ventilation under legislation specific to the mining industry. In the United States, the federal government's responsibility for mine safety has evolved over the years through a series of legislative actions beginning in 1865 and continuing through 1910, 1941, 1947 and 1952.The passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966 (the 1966 Metal Act), the Federal Coal Mine Health and Safety Act of 1969 (the 1969 Coal Act) and the Federal Mine Safety and Health Amendments Act of 1977 (the 1977 Mine Act) arc the most important milestones in this long legislative history. The 1977 Mine Act adopted many of the stronger features of the Occupational Health and Safety Act of 1970, perhaps the most significant piece of legislation on workers' occupational health and safety in US history.It is worthwhile to ask, ""How far has the United States come in mine ventilation since the enactment of the 1969 Coal Mine Health and Safety Act?"" This Act and its associated regulations defined in great specificity many standards for healthful and safe operation of a mine and. in some cases, what constitutes good ventilation practice."

Nov 1, 1995

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

By Gary R. Gavan

This report presents the documentation and User's Manual for a data retrieval and report generation computer program. The program operates on a data base containing over 19,000 pieces of coal mine equipment in use in 1976.

Jan 1, 1979

By George A. Savanick

The U.S. Bureau of Mines has patented and transferred to industry an abrasive-enhanced water-jet rock drill. This drill incorporates three novel components: a collimator, jet deflectors for cutting clearance, and an unpressurized swivel, which rotates at 1,000 rpm while passing 20 gpm of an abrasive slurry flowing at 1,000 ft/s. Drilling occurs through the action of a 10,000-psi, 2O-gpm water jet into which is entrained 72 lb/min of abrasives. The pumps, hoses, and fittings are those commonly used in the water-jet-cleaning industry. Only inexpensive, common sandblasting abrasives are used. This drill can cut through hard rocks with moderate-pressure jets; e.g., rocks with a compressive strength of 73,000 psi can be drilled with a 1O,OOO-psi abrasive jet. In addition to drilling holes, the drill can cut deep, narrow kerfs; collar a hole at any angle; drill through rubble; and chamber holes. The development of the abrasive jet drill is a significant advance in the state of the art of hard-rock drilling. The Government of the United States has licensed the abrasive jet drill patent to Weatherford Water Jetting Systems.

Jan 1, 1989

By S. J. Gasior

Pilot plant studies showed the technical feasibility of fluidized-bed operation for producing hydrogen and synthesis gas by the steam-iron process. A mixture of iron and iron oxide from 20-to 100-mesh was partially reduced with a simulated producer gas and then oxidized with steam and/or carbon dioxide. Results of tests show the effects of pressure, temperature, bed height, gas-to-solids ratio, type of iron oxide, and composition of gas on the gas and solids conversions during reduction and oxidation. A baffled free-fall solids system was also found operable. The short residence time of about 5 seconds limited conversion of the solids.

Jan 1, 1961

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane, a new refrigerant that has a remarkably low toxicity. Continued research by the Frigidaire Corporation and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964