Search Documents

By Frank B. Fulkerson

This is the second of two interrelated studies of waterborne transportation. The first study discussed transportation of mineral commodities on the inland waterways of the South-Central States.2 Together, the two surveys describe and analyze the flow of foreign and inland waterborne commerce of the gulf coast. All the principal mineral-industry imports and exports of the gulf coast are mentioned in the report, including metals, nonmetals, and mineral fuel products, The gulf coast foreign trade in mineral industry products was determined to be composed of a small number of commodities.

Jan 1, 1971

By D. W. Blaylock

1. The Lower Freeport and Lower Kittanning beds are the most important beds in Clearfield County, Pa., from the standpoint of production. The Lower Kittanning bed has the largest remaining recoverable reserves of any of the beds in the county. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,909 million short tons as of January 1, 1953. Of this total, 1,177 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By W. M. Merritts

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining, This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes, In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased.

Jan 1, 1962

Note: This is a progress report and therefore not necessarily conclusive. Further data may result in conclusions somewhat different from those reported here. Crop Growing Season The monthly average temperatures, total precipitation, and evaporation for the demonstration mine are shown in Table 1. [ ]

Jan 1, 1980

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980

By D. Harrington

Metal-mine fires in the United States are not of frequent occurrence and relatively for of those that do occur result in loss of life, although many cause heavy property loss or are costly to extinguish. Over a span of years, however, more lives are lost in metal Trines from fires than from any other of the untoward occurrences which afflict metal mining, such as electrical storms, floods, cave-ins, magazine explosions, or strikes. In perhaps more than 90 per cent of the fires. in metal mines' there is no loss of life; hence, the general public, even the general mining public, seldom hears of these fires, though the property loss frequently reaches hundreds of thousands of dollars; on the other end, in some instances the property damage from an underground metal-mine, fire has been negligible and the loss of life comparatively high. In any comprehensive study of metal-mine fires, ventilation is certain to be found a vital factor. The influence of ventilation on fires and the influence of fires on ventilation are of vital importance. In metal-mine fires very few persons meet death from actual contact Pith heat or flame; nearly all fatalities are duo to asphyxiation or suffocation. A well-planned, well-installed, and well-operated mechanical ventilation system is unquestionably one of the best available present-day protections from loss of life and property in case of fire in a metal mine; that this is true is attested by the usual helplessness of mining officials in trying to handled underground fires in a mine that has not had the foresight to install mechanical equipment to control underground air flow. On the other hand, the establishment of high-velocity air currents without sufficient day by day attention to such details as the method of coursing, or controlling, or confining them most certainly tends to increase dangers from fires rather than to aid in the avoidance or elimination of these dangers; the truth of this latter statement is shown by the fact that the greatest, loss of life in metal-mine fires during the past 20 years has been in relatively well-ventilated workings, and in every case the life loss has been due to some more or less trivial or easily remedied defect in the Ventilating system - usually a defect that has had some reference to doors used or supposed to be used to deflect or control air currents.

Jan 1, 1933

By S. H. E. Phillips

This report describes the initial feasibility, the development and the field demonstration of a system for shaft sinking employing a high energy mechanical impact rock breaker and a compatible muck disposal system. The increased shaft sinking rates, decreased costs and improved safety conditions obtainable by the elimination of the less efficient conventional drill-blast-muck cycles are discussed. Four shaft sinking concepts utilizing the impact rock breaker in various shaft configurations are developed and the field demonstration in a rectangular shaft is described. The progress achieved, the problems and their remedies and the proposed modifications to improve the machine are described.

Jan 1, 1978

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of a "line brattice air curtain" device under Bureau of Mines Contract H0357097. The purpose of this program was to develop the concept of using an air curtain for coursing ventilating air parallel with the air curtain From the last open crosscut to the face in exhausting ventilation systems to replace the line brattice cloth in room and pillar coal mining operations. The final design of the air curtain device consists of a 10-foot long closed end pipe with c: slot cut along its length. Pressurized air is delivered to the open end with a hydraulically-driven blower. A sheet of air emanates from the slot and is directed toward the mine roof. An invisible sheet of air is thus created between the top of the machine and mine roof and acts a an extension of the existing conventional line brattice.

Jan 1, 1977

By Robert L. Lagace

[Suuple Iheorctrccil models are I'M lllolalcd to cltaraclerl/c medium frequency (MF) radio vase pi opaiation in undcrgiounli room arid pillar coal mines fur the purpose of predleiln the most lavolable operating fIegtucncics,md nr,ixunum communic;IIIoil ranges for pottahIe rldu)s with I top antennas. I or conductul IrCC areas, at hree layer propaeaIion IltodcI wit II a Iiallsmissloil IIIIi- lhlllllIIal'u11 lot the plupa!edti ii unlstallt Iris been dcvcloped ;md verified experimentally. 1 lie mode u1 propaCaUetl lakes Ills form of i parallel plane (0,t)) TIM lransnussu)nhne 1% PC of mode with the electric held vertical and the magnetic held hoti/cntal t itliin a planar coal scam in which the tunnels Can he ignored and which 1s hounded above and below hp richer conductivity rock. 1lie model lilt the data best river the 200 io 1000 kH/ frequency hand and exhibits a rc;;lon of optlnrul1l Pelffelntance, with respect Io maxnluiulg radio Communication range, between 300 and 100 klf/. Maximum cunununlcatrorl ranges are sliongls dependent oil the sigiial alleilliatroil sale, ant) Illelclulc on the electrical conductivltles of the coal seam and surrounding ruck. These ranges v;ny tutu about ,,5 Io 100 nleleis Ill a high Iuss scam such as the Ilelllit No. fl to about .100 to 400 meters in a low loss seam such as the Pittsburgh foil portable intrinsically safe radios. The ieslllls die haled on the comparison oftheorc' and experiment for eleven n n. ill sesen coal seams. V OT ate is dice: a conductor such as a power Cable, is present a model has been developed for the coupling of loop antennas to a low loss Coaxial TEM ti;u?smisslon line mode in which the cable acts as the inner conducl,lr and the rock above and below acts as the outer conductor. The electuc and md' nctic Itelds for till` (node are apprlixitllatcly transverse to the cahlC and fall oil expontially with distance in the transverse plane. The principle of reciprocity is used to simplify the analysis. More expelitnental data arc needed to help resolve discrepancies between the theory and the limited data available to date.]

Jan 1, 1980

By P. M. Daling, C. A. Geffen

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume XI of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 1983

By R. R. Sayers

Although the attention of those interested in diseases peculiar to mining as teen focused recently on one duct disease - silicosis - other respiratory diseases may cause more suffering and economic loss. The increased incidence of these diseases usually is attributed to exposure to abnormal air conditions underground, such as sudden changes from high to low temperatures, excessive dust, and noxious gases. The principal respiratory diseases to which the mine is subject axe bronchitis, influenza and pneumonia, pulmonary tuberculosis, anthracosilicosis, and. silicosis. Although the mortality statistics in some of the tables included in this paper are old they have been corroborated by later, lees complete data Bronchitis Bronchitis is en inflammation of the bronchial tubes due, among other causes, to the inhalation of irritants such as dusts (organic and inorganic). Occupations that entail exposure to atmospheres polluted, by irritating gases carry with them the risk of bronchitis. According to Collie (1), it cannot be distinguished clinically from bronchitis occurring among the general population, and its association with tae inhalation of dust or gases usually is unrecognized.

Jan 1, 1941

By Terry Muldoon

In conventional noncoal, room-and-pillar mining, the cutting machine is frequently a major source of airborne dust. Water is often used for dust control. An evaluation of typically used water systems during this program showed that they reduced dust levels by 60 to 70 percent over dry cutting when at least 0.5 gpm of water was applied. These systems, however, are only marginally effective in maintaining compliance levels and the added moisture causes operational problems. During the program, three additional dust control systems were designed, fabricated, and evaluated. The first, a hollow cutter bar, was designed to capture dust in the kerf at the cutting zone. The system was only marginally effective in reducing dust levels due to its lack of control of other sources. Large quantities of material captured by the system made it operationally questionable. The second, a machine mounted exhaust system, was extremely effective in capturing virtually all the dust generated in the heading. The captured dust was ducted out of the heading and exhausted downstream in the crosscut. Exhausting the dust without scrubbing, however, creates problems for personnel working downstream of the cutting machine. Successful application would require changes to the mine ventilation system and mining sequence. The third, foam, injected foam from an onboard generator through a channel to the cutting zone at the tip of the bar. Test results showed that foam, using 1/3 to 1/2 the total fluid quantity, was equally effective when compared to the mine's current water system.

Jan 1, 1983

By George S. Rice, F. B. LANEY, A. J. Lanza, Edwin Higgins

Under its organic act the Federal Bureau of Mines is directed to conduct investigations relating to the improvement of health conditions in the mineral industries. This report describes the lead and zino deposits and the mining methods employed in the sheet-ground area of the Joplin district, Missouri, and discusses the causes and the methods of abating rock dust in the mines, the chemical and physical characteristics of the dust, and the quantities present in mine air. Although the preliminary investigation included a number of the "soft-ground" mines, the writer spent the larger part of his time in the sheet-ground mines, for in them alone was siliceous dust found in appreciable quantities. Some results of the preliminary investigation have been published by the Bureau of Mines in Technical Paper 105.a The territory covered in t~lCpreliminary investigation, during the period between November 7 and December 6, 1914, embraced parts of Jasper, Lawrence, Newton, and Greene Counties, Mo., and outlying districts in Kansas and Oklahoma. The remainder of the field work, to which 84 days during the period from February 9 to July 19, 1915, were devoted, was confined to the sheet-ground mines, the most important of which are situated in the vicinity of Joplin, Webb City, Carterville, and other smaller near-by towns in Jasper County, Mo.

Jan 1, 1917

The Bureau of Mines is responsible for a broad spectrum of programs for meeting the diverse and changing mineral resource needs of the Nation. These programs are managed by the Director and two Deputy Directors, who formulate general policy and program direction from the Washington, D.C., headquarters. A senior advisory staff, consisting of the Chief Staff Officer, Chief Scientist, and Chief Mining Engineer, provides advice and consultation to the Director on a wide range of scientific and technical matters and acts on behalf of the Director to maintain liaisons with other government agencies, mineral industries, and professional societies. Bureau program activities are classified into two major functions: (1) Developing new and improved technology that will make the production and processing of minerals more efficient, safer and more healthful for mineral workers and the public, and more compatible with a quality environment.

Jan 1, 1980

By W. W. Adams

Increased employment and a lower accident-frequency rate were the outstanding features of the metal- and nonmetal-mining4 industries of the United States in 1939 compared with 1933, according to reports furnished by individual mining companies to the Bureau of Vines, United States Department of the Interior. Except for 1937, the reports for 1939 showed gains both in number of employees and number of mar -hours worked over all years since 1929. The accident-frequency rate per million man-hours of exposure to mining hazards was lower than in any year since 1925. Reports for 1939 revealed a total of 111,909 men employed in and about mines, an increase of inure than 8 percent over 1931 The total volume of labor performed at all mires was slightly more than 299 million plan-hours, an increase of mare than 10 percent over 1938. As these gains suggest, the average employee had a longer period of work in 1939, the increase amounting to r workdays per employee.

Jan 1, 1941

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By Gregory M. Molinda

Large structural faults create serious ground control hazards, as well as adversely affect coal mineproduction. Two faults related to the Pine Mountain overthrust sheet in Buchanan County, VA, were investigated by the U.S. Bureau of Mines to determine their effect on ground control and to develop recognition criteria for prediction. Five underground mines encountering these faults were visited and mapped for structural information. This information, along with surface mapping, indicated that Pistol Gap and Keen Mountain Faults show right-lateral, strike-slip faulting and bedding planes slippage, which can be projected linearly and vertically. These fault zones are up to 200 ft wide, with coalbed offsets up to 18 ft vertically, coalbed swags (depressions) up to 15 ft, and roof falls up to 20 ft high. Recognition criteria include bedding plane slips, coalbed offsets, fault gouge, coalbed swag (depressions or synclines), and disturbed bedding. These recognition criteria will help an informed operator realize that many sudden coalbed discontinuities are related to larger geologic events (in this case thrust faulting) and can be projected linearly and vertically. Ground control strategies include mine designs that minimize fault exposure. Mining plans can be adjusted based on type and extent of fault movement.

Jan 1, 1989

By K. E. Robinson

This study provides an initial indication that mill tailings produced in the Coeur d'Alene Mining District of Idaho can be placed on floodplain areas in a technically acceptable manner without artificial liners and without seriously contaminating the surrounding area. Tests have shown that landfills on these unused areas can result in returning these areas to productive use. The engineering properties of mill tailings permit construction of stable embankments. Designed slope protection inhibits water erosion. Among the environmental considerations in using tailings for landfill construction are the acid and other contamination produced by tailings and wind erosion of exposed tailings surfaces. The initial results indicate that adverse impacts are not as severe as previously thought, and mitigative measures are feasible. Based on the preliminary data, and in accord with existing Federal and State waste management regulations, a conceptual design has been developed for 23 potential landfill sites in the District, which could reclaim 750 acres of floodplain. A cost analysis of landfill construction with mill tailings indicates that the method would be an economically viable means for increasing the valleywide tailings storage capacity, provided construction with slurried tailings is feasible. A Stage H study is proposed to evaluate slurried tailings as a foundation material, as opposed to hauled tailings used in this present study.

Jan 1, 1981

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the sixth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Fayette County, Pa., which comprises the Uniontown and parts of the Brownsville, Connellsville, Donegal, Waynesburg, Masontown, and Confluence, Pa., Morgantown and Bruceton, W. Va., and Accident, Md., quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals ar.9 included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information.

Jan 1, 1951

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935