Search Documents

By John R. Hoskins

The Bureau of Mines conducted an investigation to more exactly define the influence of some end conditions on the laboratory-determined uniaxial compressive strength of rock samples. Limestone, marble, sandstone, and granite were used to provide a range of specimen modulus of elasticity from 2.7 X 106 psi to 10 x 106 psi. Four variables were studied: Nonparallelism and surface texture of specimen ends were the specimen variables investigated; the end platen size and the adjustable or spherical head friction were the machine variables studied. It was concluded that the loading ends of small laboratory models and samples should be prepared with surface irregularities that do not vary from a plane surface by more than 0.001 inch. It was also concluded that nonparallelism of the specimen ends should not exceed 8 minutes for a rigid head load or 15 minutes for an adjusting head load. The measured compressive strength of specimens prepared with these tolerances will be statistically the same with any diameter or thickness of platen and any degree of head friction if initial alinement of the specimen is assured.

Jan 1, 1968

1. Domestic Production and Use: In 1982, 13 companies operated 30 primary aluminum reduction plants, with 3 firms accounting for 55% of production. Washington, Oregon, and Montana accounted for 34% of the production; Texas, Louisiana, Missouri, and Arkansas 18%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central and eastern States 34%. Based on published producer prices, output of primary metal in 1982 was valued at over $5.5 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 39% of domestic consumption in 1982, transportation 20%, building 14%, electrical 8%, consumer durables 8%, and other uses 11%.

Jan 1, 1983

By Arthur L. Murray

"INTRODUCTION In compliance with those provisions of the organic act establishing the Bureau. of Mines which relate to improvement of health conditions of persons engaged in the mining, preparation, or treatment of mineral substances, sanitary surveys have been made of towns and villages housing the coal miners, metal miners, and mill and smelter employees of Utah.The purpose of the surveys is to afford studies of conditions prevailing in the various mining and smelter towns so far as concerns housing, water supplies, sewage disposal, refuse disposal the handling of foodstuffs, general sanitation, wash and. change houses, and the control of preventable diseases, all of which directly or indirectly have a bearing on the health and efficiency of employees and their families. Certain other factors have been added to the general sanitary surveys such as school and recreational facilities, which have a decided influence on contentment and efficiency. Through comparisons of favorable and unfavorable conditions and practices, and the dissemination of such information, improvements can be effected which will benefit both the employees and the employers.ACKNOWLEGMENTSAcknowledgment is made of the many courtesies shown by the officials of companies and towns visited. In some instances the towns were entirely under the control of officials of mining companies, being on company property whereas, in other instances, the towns wars incorporated not under company management. Particular acknowledgment is made of the assistance given by the Utah State Board of Health through Health Commissioner Dr. T. B. Beatty."

Oct 1, 1932

By Jr. Brinkley

For a theoretical description of power plants that derive their energy from the combustion of a fuel, it is necessary to solve, to an appropriate degree of precision, a hydrodynamic problem that requires for its solution a knowledge of the thermodynamic properties of the working fluid com-posed of the products of the combustion reaction. It is usually a good approximation to assume that the properties of the combustion gas are determined by the conditions of thermal equilibrium, and it is thus possible to employ the methods of Classical thermodynamics for their computation. The thermodynamic properties of fuel gases also are of considerable importance, as they form the basis for the design of appropriate means for their effective utilization. The specification of the operating conditions to produce a gas for use as an intermediate in a chemical process, such as the synthesis of liquid fuels, may be based upon a study of the variation of the composition of the synthesis gas with changes in the various process variables. Although there exists a large number of important scientific and technical applications of the data that can be obtained from the systematic determination of the thermodynamic properties of combustion gases, such application has been greatly handicapped by the extremely tedious and time-consuming computational methods required. The development of large-scale automatic computational equipment makes feasible the initiation of a systematic program for the determination of the thermodynamic properties of combustion gases and for the application of such data to specific problems of scientific and technical importance. As a part of its program of basic research in flame and combustion phenomena, the Explosives and Physical Sciences Division of the Bureau of Mines is engaged in such a program. The present communication is designed to introduce a series of reports presenting the results of this program.

Jan 1, 1951

By T. N. Rushton

Rate minima are encountered in the reduction of magnetite with hydrogen. In a certain temperature zone, the reaction rate decreases with rise in temperature. This is inexplicable by classical kinetic theories; neither is a transition in reduction mechanism suitable for interpreting the observed behavior, This anomaly can be fully explained by hypothesizing two species of chemisorbed hydrogen with different adsorption coefficients and activation energies for adsorption. Competition between two energetic states of adsorption occurs with temperature rise, with the low energy state predominating below the anomalous temperature zone and the high energy state above it. The presence of two possible adsorption sites appears to be characteristic for oxidic adsorbents.

Jan 1, 1968

By Paul G. Marinos, Vassilis Marinos, Evert Hoek

The Geological Strength Index (GSI) is a system of rock mass characterization that has been developed in engineering rock mechanics to meet the need for reliable input data related to rock mass properties required as input for numerical analysis or closed-form solutions for designing tunnels, slopes, or foundations in rocks. The geological character of the rock material, together with the visual assessment of the mass it forms, is used as a direct input for the selection of parameters for predicting rock mass strength and deformability. This approach enables a rock mass to be considered as a mechanical continuum without losing the influence that geology has on its mechanical properties. It also provides a field method for characterizing difficult-to-describe rock masses. Recommendations on the use of GSI are given and, in addition, cases where the GSI is not applicable are discussed.

Jan 5, 2007

By M. A. Trevits, T. A. Gray, L. M. Crayne, P. Glogowski

Mine seals can he remotely constructed in underground coal mines through vertical boreholes when direct access to a fire is impossible or considered to he too dangerous. This method has great merit because the boreholes can be drilled to specific mine areas, and the seals can be positioned close to a fire zone. The technology however can be largely ineffective if the constructed seals do not provide of effective barriers to airflow or if they cannot he used to impound water and other inert materials. Unfortunately, no viable alternatives exists to sealing the entire mine to the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL). Under this effort. Howard Concrete Pumping Company and GAI Consultants Inc. have joined forces to evaluate a potentially significant improvement to the current state of the art. This paper covers the development o f novel technology or rewrote mine seal construction, the evaluation of rite materials used, the construction practice and the Fellow-up testing.

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in more intensified efforts in inspections of coal refuse sites. Inspections, however, are mainly qualitative and time consuming. In August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photointerpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Bibliographies of literature reviews in the area of past coal refuse embankment failures, monitoring instruments and methods, and photogrammetry are included.

Jan 1, 1977

By R. G. Travis

1. Reserve estimates have been made for eight coal beds in Monongalia County, W. Va., but only the Pittsburgh, Sewickley, and Upper Freeport beds are important at this time. The Pittsburgh, Sewickley, Waynesburg, and Upper Freeport beds contain the largest recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 3,526 million tons as of January 1, 1954. Of this total, 3,294 mil-lion tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By Jr. Hazen

This report documents 653 sets of sample data involving 78,366 assays obtained from past exploration for various minerals and metals. Most of these data have been taken from published reports describing exploration projects, conducted jointly by the Bureau of Mines and the Geological Survey, for the Strategic Minerals Program from 1940 through 1949. Means and standard deviations have been computed for the exploration assay data and have been plotted on graphs for 22 minerals and metals. A mathematical model, based on the binomial distribution, has been developed to explain the configuration of the plots of the exploration means and standard deviations. The two statistics, mean and standard deviation, which describe assay data, have been used for simulating probability models. These probability models then have been combined with the binomial model of the exploration assays and related to the sequential decision process associated with exploration drilling for mineral deposits. These probability regions can be used to form the basis for sequentially predicting the probable range of the average grade of mineral or metal that may be expected as an exploration drilling program is continued after the initial discovery of mineralization has been made.

Jan 1, 1966

By Frank J. Wiebelt

Under a general program to extend the resources of mineral deposits, the Bureau of Mines examined the Quien Sabe antimony mine in October 1948. The preliminary evaluation demonstrated that a diamond-drill program was warranted co establish the tenor and persistence of the veins and permit an estimation of antimony reserves. The Bureau of Mines conducted a diamond-drilling program on the property from December 1949 to May 1950. Ten holes aggregating 2,483 feet were drilled. Nine of the holes encountered antimony-bearing vein material.

Jan 1, 1956

By W. P. Yant

[This report describes results of a study bf the carbon monoxide and particulate matter in the air of the Holland Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development]

Jan 1, 1941

By Alan A. Campoli

OD March 20, 1989, a meeting was held at the U.S. Bureau of Mines Pittsburgh Research Center at the request of Senator Pete V. Domenici of New Mexico. The purpose of the meeting was to engender a technical relationship between the National Laboratories and the minerals industry. During the meeting, the Director of the Bureau of Mines, T S Ary, suggested that since the Bureau is the focal point for mining research in the United States, it would be appropriate for the agency to act as the liaison between the National Laboratories and the minerals industry. As the first step in this process, the author was selected to perform a 6-month investigation to better define the proper role of the Bureau in this area. As part of the investigation, the mining and mineral-related technology available at 21 major U.S. Department of Energy (DOE) Research Laboratories was reviewed. It was assumed that the broad range of scientific and technical areas covered DOE research would provide fertile ground for mining-related technologies. It was hoped that the applicability of DOE research to this liaison effort would be indicative of Federal laboratories in general.

Jan 1, 2011

By Slavoljub D. Maksimovic

The Bureau of Mines, through a memorandum of agreement with the State of Ohio, tested a method of constructing seals in abandoned mine openings in Ohio by means of pneumatic stowing of crushed limestone and gravel with sand. A total of five openings and one shaft were back-filled. Pneumatic stowing uses compressed air to convey material through a pipeline and into the mine opening. The stowing equipment consists of a power supply, a blower, a feeder to inject the material into the pipeline through an airlock, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. Well-graded aggregate up to 2 inches in diameter and having sufficient fines is used as fill. The stowing method is safer and faster than conventional methods, is cost competitive, prevents trespass into abandoned mine openings, and eliminates or reduces the exposure of workers to possible hazards since the discharge nozzle can be kept at the mouth of the opening. The equipment is mobile, and, with some modification, the technique could be widely used for sealing abandoned and active mine openings, even in remote locations and during severe weather conditions.

Jan 1, 1982

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds in Russell County , Va . Almost 2 million tons of coal was mined in 1961 ; 75 percent of the coal was cleaned mechanically in preparation plants in the county . The coal of Russell County is ranked as medium- to high- volatile bituminous , contains small amounts of sulfur , and generally requires some cleaning to reduce the ash content to limits acceptable for metallurgical purposes .

Jan 1, 1963

By Laurel A. Powers

The Bureau of Mines process for recovering Ni and Co from low-grade domestic laterites uses a reduction roast followed by an ammonia, ammo-nium sulfate leach. This investigation examined the waste streams of the process for their potential environmental impact and focused on the laterite residue produced. The U.S. Environmental Protection Agency's extraction procedure (EP) toxicity tests and column leaching showed that leachable metal concentrations would be low enough so that the residue would not be considered a hazardous waste under present definitions. Under nonacid leaching conditions, about the same amount of metal was extracted from laterites as from their residues, and the leachates were similar to water samples from an undisturbed laterite deposit. Washing tests on the laterite residue showed that ammonia and ammonium sulfate concentrations were reduced according to equilibrium stage calculations, resulting in residues that would be acceptable for revegetation. With water washing only, the residue would not be considered a hazardous waste even though significant amounts of Ni and Co were absorbed from entrained leach solution onto the residue. Washing first with fresh leach solution and then with water prevented this absorption and thus improved the overall metal recovery.

Jan 1, 1983

By R. W. Michelson

The Bureau of Mines developed computerized mathematical models to estimate the economic availability of Mesabi Range taconite concentrates; these are a quality model, a cost model, and an economic availability model. The quality model evaluates metallurgical test data; the cost model determines iron unit cost from mining and processing cost data; and the economic availability model determines quantity from geologic and ore quality data. By correlating all of the physical resource quality factors and dimensional characteristics with the economic cost factors associated with producing iron ore pellets, these three models combine to establish a final relation between iron ore reserve quantities and iron unit cost.

Jan 1, 1970

By Thomas W. Camm

In this U.S. Bureau of Mines report, mine and mill cost models are presented to make quick estimates of the cost to develop mineral deposits in the desert region of the Southwest United States. Regression analysis was used to generate capital and operating cost equations for each model in the form Y = AXB, where Y is the cost estimated and X is the assumed daily capacity in short tons. A and B are constants determined by the regression analysis. Each is broken down into 11 subcategories to facilitate escalation of costs for inflation and to increase their versatility in economic evaluation work. This report contains 2 open pit models, 6 underground mine models, 11 mill models, and cost equations for access roads, powerlines, and tailings ponds. In addition, adjustment factors for variation in haulage distances are provided for open pit models and variation in mining depths for underground models.

Jan 1, 1991