Search Documents

By Jose a. Sanchidrian, Ramon G. Eguren, Javier L. Amigo

On December 2013 a MEMU exploded at a blasting site in Norway, after burning for more than two hours. This paper describes the analyses made to determine the actual yield of the explosion, the lessons learned from the event and the actions taken as a consequence. The conclusions of the analysis were the following: - The yield of the explosion was 650-1450 kg TNT. In terms of AN and ANE they correspond to 1300 – 3700 kg AN, or 950 – 2450 kg ANE or ANE/AN blend. These quantities are 8 to 31 % of the explosive precursors in the truck. The burning of the truck and its load for two and a half hours had consumed more than two thirds (perhaps up to 90 %) of the explosive precursor material.

Jan 1, 2016

By Charles Zdazinsky

Over-break is undesirable in underground civil construction because it excessively damages rock along the perimeter of the tunnel, which directly influences the cycle times of advancement. A quicker cycle time for each process is required to optimize the operation and therefore minimizing over-break is essential for operational success.

Jan 1, 2015

By Gabsoo Kim, Rulin Yang, Dave Kay

Blast vibration data, such as PPV are usually scattered. In many cases, plots of PPV versus the charge weight scaled distance are so scattered that useful trends from different blast designs cannot be identified. The scattering of the data may be attributed to the inaccuracy of the PPV measurement, the definition of the scaled distance from a multiple-hole production blast, and the measurement of distances and charge weights. The error from vibration measurements is one of the major contributors to the scattering of the plots. If accurate monitoring is conducted, improved design options may be identified. This paper documents two case examples that compare different vibration sensor couplings. The first case shows mounting accelerometers at spots that protrude from the ground, compared with the sensors that were mounted on a flat ground surface. The second case compares data from loose-sand buried geophone with that from sensors coupled to the ground using concrete blocks.

Jan 1, 2014

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By Robert McClure

The detection, recovery and disposal of commercial explosives and explosive waste has always carried a level of risk and requires specialized equipment and technical expertise. Improperly stored, discarded, deteriorated, misfired, stolen or surplus products are often the primary sources of explosives that require safe disposal. Detection and disposal tools available today have advanced significantly due to developments in Counter-Improvised Explosive Devices (C-IED) operations and commercial blasting technology. These technologies have provided safer more efficient ways to detect, investigate and dispose of commercial explosives products in order to minimize property damage and potential harm to disposal personnel and the general public.

Jan 1, 2015

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By Larry Schneider

"0 ne of the incentives that led to the development of non-electric shock tube initiation systems was the desire within the industry to improve detonator safety. And to the extent that nonelectric initiators are immune to the hazards of stray current and radio frequency energy found on normal blast sites, an advancement in safety has been accomplished. However, as a cautionary note, it is important to realize that there are still many hazards associated with any initiation system. While some of these hazards may differ from those associated with electric detonators, others are identical to those associated with any type of initiation system. For instance, contrary to what some uninformedblasters may believe, lightning remains a hazard when using nonelectric initiation as well as electric initiation."

Jan 1, 1995

By R. F. Favreau, Patrice Favreau

"A blast with explosives creates vibration waves in the zone around the blast.The prediction of the intensity of vibrations is important because people in the cinity demand that the vibrations do not disturb them, and society imposes limits on the vibrations. The U. S. Bureau of Mines (USBM) showed that the easurement of the particle velocity U predicts the risk of damage from vibrations. A currentapproach of blasters to monitor vibrations is to measure them with a seismograph at several distances S, and create a graph of U vs. S and the explosive charge “W” according to the equation U = K / (S / W)N where K and N are constants that depend on the blast method and the nature of the ground over the distance S. Though useful, this equation is empirical, and the results predicted from it are very variable, as shown by figure 1 which indicates that a prediction of U can deviate significantly from the actual value. Moreover, a minimum of two seismograph measurements at two values of S are required to establish the curve. However, here now exists another very convenient method to predict U; it is with the simulator Vibmas, which is based on the fundamental principles of how a blast reates vibrations. This simulator takes into account not only W but rather all the blast parameters, the type of explosive and the properties of the rock. Moreover, to establish the calculation of U as a function of S, only one seismograph measurement is required rather than two as for the USBM method. This last difference is important because it makes it easy to predict U not only as a function of S, but also as a function of the orientation of S. On the site this allows much safer control of the vibrations, and the use of larger explosive charges which reduce excavation costs. The article presents results from a field case at a hydroelectric project in Canada, where the deviation was very moderate. Use of this vibration simulator on the Web is very easy."

Jan 1, 2015

By Hans Perlid

In the handling of emulsion explosives pumping is a key operation. A number of serious accidents has shown that pumping can be a risky operation and should be carefully considered and investigated. This is the background behind a series of pump tests carried out by NITRO NOBEL.

Jan 1, 1996

By Don Z. Painter, Gordon F. Revey

Frontier/Traylor Joint Venture is presently constructing a section of the Tri-County Metropolitan Transit District of Oregon's (TRI-MET) Westside Light Rail system. This new section will extend Portland's existing transit system to the western suburbs of Beaverton and Hillsboro. The drill-blast excavations at this project include 10,000 feet of 20 foot tunnel, 18 cross passages, three shafts, an underground railway station, and a U-wall open cut. From a blast designer's perspective, this job has been extremely challenging. Blast vibration is limited to 0.5 ips at 200 feet or at the nearest structure, and airblast is limited to 129 dB -- linear peak and 96 dB -- C scale. The tunnels pass under heavily built up areas and have top of tunnel to surface cover distances as low as 70 feet. Surface blasting in the 26,000 cubic yard U-wall excavation was limited to five short nighttime periods due to its proximity to the very busy highway 26.

Jan 1, 1995

By Charlie Adcock, Rob Farnfield, Andy Wetherelt

The ISEE Blasters Handbook gives guidance on the level of air overpressure likely to cause occasional window breakage (151dB) and general window breakage (171dB). A long-term safe level of 140dB is also suggested. This guidance is widely used by demolition and other contractors to assess damage zones in the region of explosive applications employing unconfined charges. Other reference material gives more detailed guidance relating to window area, aspect ratio and glass thickness. Despite the guidance given in these references, complaints by members of the public regarding window breakage continue to be received by explosives engineers from air overpressure levels well below the longterm safe limit. Such complaints are not limited to the use of unconfined charges but can even be generated from the highly confined use of explosives in quarry blasting. This paper describes a series of experiments with explosive charges fired in unconfined conditions close to various window configurations. The aim of the work was to test the existing guidance levels and to extend the knowledge base in this area. Topics covered include the role of differential pressure across windows in the walls of an enclosed space such as a room.

Jan 1, 2006

By Robert Morgan

The mind-set that only blasters and their helpers need training in explosives can result in risk to other employees working at mine or construction sites where blasting is conducted. Misfires are not always immediately obvious during postblast examinations performed by the certified blaster in charge; the presence of undetonated explosives may not appear until well within the muckpile as was the case in the photo, right. To avoid accidents involving misfires, follow safety procedures specified in mine safety regulations, and the ISEE Blaster’s Handbook that include the following:

Jan 1, 2004

By Dean Nichols, Matt Ortel

Explosive accidents in the United States have brought increased attention to emergency operation plans (EOP) at all facilities that manufacture, transport, or store hazardous materials – particularly explosive materials. Explosions are sudden, powerful, and complex events that are difficult to characterize in terms of the thermal, over pressure, and debris effects. Industry, regulatory, and public officials require emergency response planners to not only anticipate the blast effects of an explosion, but also to prepare an appropriate response.

Jan 1, 2016

By U. Gorkhan Akkaya, N. Enver

Geographic information system (GIS) is one of the most accurate and useful tools to help decision – making for decision-makers. As to expert systems, it provides solutions to the problems faced by mimicking reasoning of the human experts. Blasting operations in mining include high risks for the vicinity of the operations. GIS having required mechanisms to take right decisions for the people who have to make right and precise decisions, while it is utilized as a integrated system with expert reasoning, is thought to be considered important tool that provides to take decisions with ease, and also to reduce the risks in the blasting operations. It is possible to find out both of the economic and optimum solutions to solve the various encountered problems in the mining activities such as blasting operations, only when GIS integrated expert systems is used. Managing the spatial data unified with expert reasoning is the one of the greatest advantages of the system. In the scope of the study, various scientific studies were investigated. The benefits of the system were figured out and the phases of a unified system were proposed in the blasting operations.

Jan 1, 2013

By Ali Kahriman, Alper Celtikc, Serdar Celik, Tuncer Gungor

This paper presents the results of ground vibration measurements carried out in Gülyali Hisarcik Basalt open pit mine located on the north side of the Anatolia near Ordu province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 5 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 5 different vibration monitors (4 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2013

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

By Jerry Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (1 l- 14 million cubic meters) of gas per day.

Jan 1, 1996

By Paulo Couceiro, Manuel Lopez Cano

"The Panama Canal is one of the most important engineering projects of the modern era and plays astrategic role in the global economy and international maritime trade since its inauguration in 1914. Now, a little more than one century later, the final phase of its expansion program, the largest infrastructure works undertaken since its inauguration, has concluded. This expansion program has created a new lane of traffic along the Canal with the construction of a new set of locks – one on the Pacific side and another one on the Atlantic side -, increasing the Canal’s capacity and its impact on the world’s economy even more."

Jan 1, 2017

By Milos Bila

The second half of 2008 and the first half of 2009 brought up important anniversaries. My old passport from Czechoslovakia has a stamp with date 10-10-1968 at 10:00 AM, the exact time I crossed the border between the former Czechoslovak Republic and Austria. This date has an important meaning because I could not come back to my country for the next 21 years. The 40th anniversary of Soviet led invasion, which took place on the 21st of August 2008, revealed some unknown and long time kept secret news.

Jan 1, 2010

By David Ziegler

A formal blast plan is sometimes required for projects involving rock excavation. A written blast plan submitted with a bid proposal can also be an important sales tool. A blast plan will cover the basic elements of shot design: hole diameter, spacing, burden, loading, and so forth. Some suggestions are discussed here for additional items or topics to address, including: safety issues, ground control, traffic & site control, public relations, pre-blast inspections, seismic monitoring.

Jan 1, 2003