Search Documents

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014

By Nilmara Dias, Maria Margarida Martins, Maria Teresa Carvalho

"The heavy residual fraction of the mechanical and biological treatment (MBT) plants treating undifferentiated municipal solid waste is mostly composed by inert materials, such as glass, stones, ceramics and brick. Glass, appearing in significant grade and amount, is not recycled today due to the high content in the other materials, mainly stones. All these materials have approximately the same density but stones have significantly different shape from other materials particles. In this paper it is presented the research developed to eliminate stones appearing in the fine fraction (2.8-8 mm) of the MBT plants heavy residual fraction (MBTr) using a shaking table operated in dry conditions. Two different samples from two different MBT plants were used. Firstly, the samples were characterized (materials content and particle size analysis). Then, laboratory work was carried out to optimize the operation of the shaking table, by changing the machine parameters, deck slope and movement frequency. The study showed that it is possible to upgrade the product in glass. The best results, obtained with one single stage of processing, were 82% content in glass with 84% in recovery, in the glass concentrate, when the coarser fraction (-8+5.6 mm) of one of the MBT plants was used. With the intermediate particle size fraction (-5.6 + 4mm), the glass concentrate attained 74% content in glass with 91% recovery."

Jan 1, 2014

By Nirmal S. Weerasekara, Malcolm S. Powell, Mohsen Yahyaei

"An understanding of the fundamentals of different breakage mechanisms is critical for successfully modelling comminution processes. Due to the high frequency of low energy collisions in the grinding process, superficial breakage has a significant role in size reduction in mills. To develop a scaling up methodology for characterising low energy surface damage behaviour of ores, a series of surface damage tests have been conducted using three grinding mill sizes with diameters of 1.8, 1.2, and 0.8 m. Two types of gold-copper ore with different hardness were used: C-ore and T-ore. All tests were conducted using wet mode to remove the products during grinding. To ensure low energy surface damage was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. A surface damage index normalised with product mass and surface based specific energy is determined from the results enabling a study of the grinding performance regardless of mill size, energy level or charge mass. Incremental breakage tests using the JKRBT indicate that the A×b values of the T-ore were 60% higher than C-ore, suggesting the T-ore is considerably softer. The fractional mass loss rate for the T-ore in the 0.8 m and 1.8 m mills started from 16 and 7 (1/kWh/m2) while for the C-ore it was 4 and 2 (1/kWh/m2). After 6 minutes the surface damage index in all tests tends towards steady state a constant value, an indication of steady state surface damage condition. It has been demonstrated that this methodology can be a useful basis for characterising superficial breakage behaviour of ores."

Jan 1, 2014

By M. Wright, A. H. Mwale

This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered.

Jan 1, 2003

By Alex Heath, Andrew Barycki, Baladron. Javier

"Efficient flocculation is important to thickener performance, affecting the overflow clarity, solids settling flux, underflow density and operability. Many factors affect flocculation; from the material/flocculant type, dilution of the feed and flocculant solution, mixing, to the shear rate and shear history. The flocculant addition point (or points) can be used as a tuning method to alter the effective flocculation time in a feedwell, with addition further up the feed pipe increasing the residence time but making the aggregates more prone to breakup if they experience high shear later in the process. Conversely, adding the flocculant later, eg under the feedwell shelf decreases the mixing time but allows some free (unadsorbed) flocculant to be available at the feedwell exit. An extensive trial has been performed on an operating thickener comparing seven individual different flocculant dosing positions through a Vane feedwell, and some combinations of two dosing points simultaneously. Measurements of the velocity, solids concentration and aggregate size were made throughout the feedwell at the different positions, with the dosing points significantly changing the aggregate size and clarity, and also affecting the solids concentration at some positions. The results are accessed in terms of flocculation kinetics and used as CFD validation data."

Jan 1, 2014

By Achilles Dutra, Everton Santos, José Oliveira

The beneficiation of phosphate ores by froth flotation is the most efficient process used to separate apatite from gangue minerals like calcite, dolomite and quartz. However, the similarity of surface properties between apatite and calcite generally lead to non-selective adsorption of reagents, rendering the selective separation of these minerals a worldwide problem. The phosphate deposit of Itataia, State of Ceará, Brazil, studied in the present work, presents a complex mineralogical composition having uranium associated with the apatite mineral. The main gangue minerals are calcite and quartz. The bulk flotation of apatite and calcite with anionic collectors in an alkaline medium followed by the selective flotation of calcite at pH 5.5 using phosphoric acid as well as citric acid as depressant have been suggested for this ore. This paper presents the results of contact angle measurements obtained using jojoba oil, a natural reagent composed mainly of gadoleic acid (C20:1) and long-chain fatty alcohols (eicosenol and docosenol), as an alternative collector for the selective separation of apatite and calcite minerals. The hydrophobicity studies were carried out using a computer controlled contact angle goniometer. Additionally, the collector adsorption was evaluated via electrophoretic mobility and FTIR measurements. The results indicated that a high selectivity can be obtained by using jojoba oil as collector in a slightly acid pH range, without the use of depressant. The best results were achieved with a jojoba oil concentration of 200 mg.L-1 at pH 6.5, where the apatite was fully hydrophilic and calcite showed a high hydrophobicity (? > 60 º).

Jan 1, 2014

By Tuan V. Nguyen, Kosta Simic, Louis Mittoni, Murray Rudman, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D .Improving Thickener Technology. project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By Pawel Strzalkowski, Marta Baszczynska, Urszula Kazmierczak

The paper presents issues related to interference of mining activities with the environment. Exploitation of mineral resources causes primarily a modification of the landscape. All of the negative impacts on environment are short-lived and last as much as it takes to exploit the raw material. After the mine closure reclamation is necessary during which all aspects that reduce harmful effects of the mining activities on the environment must be taken into account. Current ways of reclamation allow recreating natural environment, which is different from the original and enriched in diverse new values. This requires propositions of new forms of converted land development through a detailed analysis of technical, natural, planning, economic and social sphere requirements. Before making final decisions regarding selection of direction of reclamation, a thorough analysis of the key factors has to be carried out. All steps related to the implementation of the reclamation project are shown in the paper using Limestone Mine "Górazdze" located in the south-western part of Poland as an example. This paper also presents an analysis of current ways of post-mining reclamation towards agricultural and forestry landscape, along with our own suggestion for their extension in order to preserve biodiversity. For choosing optimal solutions the most relevant criteria were considered: existing natural values and possibility of their protection. Taking into account the economic and social aspects, supported by natural potentials, implementation of tourism and recreation in this area were proposed. It was shown that this proposition would not interfere with the current trends of the natural landscaping. Finally, after completion of reclamation and land development in the considered mine area, creation of a geo-park was proposed along with appearance of geotourism in the area. To illustrate the proposed forms of post-mining land development in the form of maps, an ArcGIS(ESRI) software was used.

Jan 1, 2014

By Megan Becker, Cyril O’Connor, Jenny Wiese, Gaynor Yorath

The effect of particle shape on true flotation has been widely reported. The present paper presents results obtained in investigating the effect of particle shape on the entrainment of particles during the flotation process. Different hydrophilic minerals with particles of varying aspect ratios were used and their shape determined using rheological tests and QEMSCAN. Their entrainment properties showed a close relationship to their shape with the recovery due to entrainment increasing as the aspect ratio of the particles increased. The effect of surface charge, by changing pH, and size of particles showed that the effect of shape was sustained at different pHs and particle sizes. Proposals are made to explain these observations in terms of the known relationships between drag coefficients and terminal velocities and shape. Since it has been previously reported that different milling procedures can affect particle shape, these results indicate that it is possible that such different procedures may result in increased entrainment of hydrophilic minerals.

Jan 1, 2014

By Paulo Castillo, Cesar Gomez, Jaime Alvarez

Operations using flotation to produce mineral concentrates require testing of frothers to characterize their ability to preserve bubble formation size and to build a stable froth. Many techniques have been proposed to measure parameters associated with these two roles. These techniques focus, in general, on only one of these roles and are based on special equipment operated at conditions quite different from those existing in industrial cells and columns. Both roles have been simultaneously characterized in a laboratory flotation column, but the requirements associated with the installation and operation of one of these units, are a serious limitation for its use on-site. A technique based on the use of a laboratory mechanical cell, a common piece of equipment in operations, will have wider application. Establishing the ability of a frother to control coalescence by preserving bubble formation size is done through bubble size measurements as a function of frother concentration. Froth build-up and stabilization is associated with the amount of water carried by bubbles into the froth layer, which has been demonstrated to correlate with the gas holdup in the collection zone. Procedures devised for determining the critical coalescence concentration (CCC) from measurements of bubble size as a function of frother concentration, and the gas holdup by collection of water displaced from the cell by the presence of bubbles at different frother concentrations, were tested. Three analytical-grade frothers were utilized: a straight-chain (1-heptanol) and a branched (MIBC) alcohol and a polyglycol (PPG425). The results obtained at a standard set of conditions, demonstrated consistent differences between these frothers, and the ranking from least to most effective for reducing bubble size or decreasing water drainage followed the same sequences found when more complex frother characterization techniques are used.

Jan 1, 2014

By M. F. He

There are three polymorphic modifications in pyrrhotite (monoclinic, hexagonal and orthorhombic), with monoclinic and hexagonal polymorph being more abundant. The floatability of different crystalline structures of pyrrhotite (monoclinic and hexagonal) is studied in this paper. It is shown that the floatability difference of monoclinic and hexagonal is obvious and that the flotation recovery of monoclinic pyrrhotite is greater than that of hexagonal pyrrhotite using different collectors . Using butyl dithiophosphate as collector, the flotation recovery of pyrrhotite is higher than when sodium diethyl dithiocarbamate and sodium butyl xanthate are used as the collectors. Monoclinic and hexagonal pyrrhotites are more easily activated by Cu2+ in acidic conditions than in alkaline conditions, while Cu2+ can not activate hexagonal pyrrhotite when sodium diethyldithiocarbamate was used as the collector. By the measurement of contact angle, it is indicated that monoclinic and hex-agonal pyrrhotite float well and are easily activated by Cu2+when dithiophosphate was used as the collector. Using sodium diethyl dithiocarbamate as a collector, the flotation behavior of pyrrhotite was investigated. The relationship between potential and pH range for pyrrhotite flotation was established. The results show that the flotation of pyrrhotite is dependent on pulp potential at certain pH values.

Jan 1, 2014

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By T. Neesse

In many cases, the use of hydrocyclone control is desirable for the stabilization of separation in the setting of changing feed conditions. Control concepts based on exact mathematical models are not satisfactory due to the complexity of the physical process. In this case, fuzzy control is a suitable solution. The data are primarily derived from an optical sensor that monitors the outside view of the free underflow stream. A throttling valve, serving as an actuator, is installed in the overflow pipe that regulates the volume split of the cyclone. Applications in closed circuit grinding and in separation plants for tunnel driving, fine sand dewatering, and classification of kaolin demonstrate the typical use of this development. Additionally, the technological characteristics of the cyclone may be improved by this control, which is mainly caused by the increased discharge capacity of the un-der flow nozzle. A further advantage is the option to operate at an optimal operation point. In many cases, this point is located at the transition spray/rope discharge. The improved operation characteristics present new options for extensive applications of fuzzy cyclone control.

Jan 1, 2014

By Yuemin Zhao

Pre-combustion cleaning of coal plays a key role in the process of efficient and clean utilization of coal resources. Recently, wet beneficiation of coal is predominant around the world. Nevertheless, wet beneficiation processes are limited by the increasingly serious problem of worldwide shortage of water, especially in China. Thus, it is imperative to develop efficient dry coal beneficiation techniques. Currently, several technologies such as air dense medium fluidized bed, compound dry cleaning and air jigging have successfully achieved high-efficiency separation of 50~6 mm coal. However, in recent years, a large amount of fine coal is generated as the mechanized mining technology has been progressively deployed in coal sector. Thus, it is necessary to develop efficient dry beneficiation techniques for fine coal. In recent years, many countries including China, India, Canada, Germen, and Australia have carried out many research works on fine coal dry beneficiation techniques. China University of Mining and Technology has carried out systematic researches on the introduction the vibrated energy to traditional air dense medium fluidized bed for fine coal beneficiation. This paper studied air dense medium vibrated fluidized beds (ADMVFB) for fine coal dry beneficiation. The experimental results show that the coal of <6 mm size can be beneficiated in an ADMVFB efficiently with the E value of 0.065~0.085, the separating density can be adjusted in the range of 1.45~2.2 g/cm3, and the lower limit of beneficiation can reach to 0.5 mm. Keywords: fine coal, air dense medium vibrated fluidized bed, coal separation, dry separation

Sep 1, 2012

By Jean-Paul Franzidis, Robert G. Coleman, Emmy V. Manlapig

"The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented mobile pilot flotation plant developed by the Julius Kruttschnitt Mineral Research Centre, the Mineral Processing Research Unit of the University of Cape Town and EIMCO, as part of the Australian Minerals Industries Research Association (AMIRA) P9 Project. Apart from being a fully operational pilot plant, the FCTR was designed to determine flotation model parameters and to develop and validate flotation plant modelling, scale-up and simulation methodologies.The FCTR was installed at WMC’s Kambalda Nickel Operation where circuit modelling, simulation and scale-up test work was performed using the AMIRA P9 flotation model as the basis of the analysis. The model parameters were obtained through metallurgical sampling, batch flotation tests and gas dispersion characterisation around the FCTR. Model parameters were determined for four FCTR circuits, each of increasing complexity. The circuits ranged from a simple rougher-cleaner configuration with no recycle streams, to a more complex rougher-cleaner-recleaner configuration with two recycle streams.Using the P9 modelling methodology, the system was analysed using four mineral species: nickel sulphide, iron sulphide, copper sulphide and non-sulphide gangue. The floatability of each mineral was analysed as two floating species (fast and slow) and a non-floating species. Mass balanced data from all four FCTR circuits were regressed simultaneously together with data from 47 batch flotation tests. Nonlinear regression was used to determine the solution. The model fit was found to be accurate with most data points predicted within experimental standard deviations. A Monte Carlo sensitivity analysis was also performed to establish the stability of the regressed parameters.Using the P9 simulation methodology, simulations of five FCTR circuits (different from the previous four) were performed. The FCTR was also operated in these five circuit configurations to obtain experimental data to validate the simulated predictions. The simulations were found to predict the recovery and grade of nickel sulphide and copper sulphide within experimental standard deviations. The prediction of recovery and grade of iron sulphide and non-sulphide gangue was less accurate. Overall the FCTR simulations predicted the changes in circuit configuration well."

Jan 1, 2003

By Luis Bergh, Iván Rojas, Juan Yianatos, Luis Vinnett

"At present, flotation rate characterization follows standard measurements to identify the overall flotation performance looking at the feed, tailings and concentrate in flotation cells or banks. This classical approach does not take into account the evolution of the true collection rate down the flotation banks explicitly. The potential for identifying the impact of the mineral characteristics (size and liberation) as well as the effect of different manipulated variables (reagents, froth depth, gas dispersion) on the true flotation process remains hindered. Top-of-froth (TOF) measurements, which consist of sampling the first layer on the froth surface, have been used to characterize the mineral collected by true flotation in rougher banks. The information provided by TOF samples allows evaluating the floatable mineral evolution (grade, particle size, liberation) down the bank. In this work, an indirect approach to estimate the flotation rate along rougher flotation banks is proposed. The new approach is based on the decreasing of collected mineral grades (on top of froth) and the feed characteristics. Flotation rates per liberation classes were used to reconstruct the TOF grades from the feed information. This approach requires a simple froth surface sampling, without constraints typically observed during mass balance surveys and uncertainties on the mineral recovery estimation. The proposed methodology was successfully applied at industrial scale using TOF measurements together with QEMSCAN information."

Jan 1, 2014

By Antoineta Boteva

A significant part of the currently production of the non-ferrous and precious metals is from sulfide ores. Character feature of sulfide ores is the presence in them always pyrite and wide range of different sulfide minerals else. These minerals are the carriers of valuable for industry metals. Due to the low content of the main components, very often call on the use of collective- selective flow-sheets. The extraction of minerals in the collective concentrates determined in a large extent the effectiveness of the collective-selective sheets. In conditions of bulk flotation kinetics to floatate of the various minerals is different. Due to why it is and how it can be used for a more effective selection of minerals ?this is the main task of this report. For this purpose are used results from the bulk flotation of pyrite, copper sulfides, molybdenite, galena, blenda. It is separated and place of host rocks. Base it of large experimentation material, including both electro-kinetic measurements of mineral systems, as well as laboratory flotation tests and factories monitoring it is established kinetics of flotation of mineral particles in conditions of collective flotation. Made an effort to clarify the effect as of the species and the proportion of different sulfide minerals involved in flotation pulp else. Traced was the impact of the density and aeration of the flotation pulp on deferens in kinetics of mineral flotation in condition of balk flotation. The obtained results are used to increase the efficiency of the diffraction flotation of the complex sulfide ores containing precious metals. In the schemes, it is possible precious metals to fall in the most appropriate for the next processing products. Keywords: flotation, sulphide ores, kinetic extraction

Sep 1, 2012

By G. K. Nimal Subasinghe

The establishment of grind size that optimally liberates the valuable mineral for efficient down-stream processing is of great importance for most mineral processing operations. Reasonably accurate comminution models as well as models of downstream separation processes may be found in the literature but their use in optimizing grind size is limited without an associated liberation model. In this work, an attempt has been made to address the above shortcoming by demonstrating how the effective parameters of the downstream flotation process may be predicted from the liberation characteristics based on the ore texture data for a disseminated nickel ore. In this regard, the liberation model based on linear intercept distributions of mineral and gangue proposed by King (1979) and its application to predict the flotation performance of an industrial plant demonstrated by Schaap (1979) may be considered useful contributions. However, while the model proposed by Schaap is simplistic enough, it is based on several assumptions due to the non-availability of intercept length measurements on the parent rock, in particular, on the extent of mineral exposure on the surface of comminuted particles. In this work, the linear mineral and gangue intercepts on polished specimens of a binary ore, comprising darker pentlandite as the valuable mineral and lighter barren host rock were measured using an image analyser. The resulting intercept distributions followed negative exponential distributions. Using the mean sizes of mineral and gangue intercepts, the proportion of liberated, compo-site and mineral occluded particles of a given size, the extent of mineral exposure on the surface of particles and their mean mineral contents were calculated using principles of renewal theory. The rock was then crushed and ground and different size fractions were floated. It has been shown that the parameters of observed recovery data based on 1st order kinetics such as the associated rate constant and ultimate recovery agrees well with those predicted from the quantities calculated above. This work has important practical implications since it can indicate variations in flotation performance arising from changes in mineralization within a large ore body.

Jan 1, 2014

Froth flotation is an industrial process commonly used for the separation of mineral particles. Bubbles sparged in a pulp collect and carry hydrophobic particles to the top layer of a flotation cell, the froth zone. There is a strong correlation between the stability of the froth phase and the flux of solids. However, flotation units placed in series operate, as a whole, in a non-steady state regime with the concentration of particle decreasing from one cell to the next resulting in a decrease in froth stability, which can compromise the recovery of valuables. Organic chemical reagents, frothers, are generally added to prevent fine bubbles from coalescing and to increase the stability of the froth phase. Frothers represent the second largest group of mining chemicals. It is crucial to understand the resulting properties of the frother on the froth phase in order to select the most suitable reagent for a particular operation. The bubble coalescence dynamic of three different surfactants, 1-pentanol, poly (propylene glycol), and tri (propylene glycol) methyl ether, were investigated in this study. In the first stage, the stabilisation mechanism of bubbles in a solution of surfactant was investigated using a specifically designed experimental setup. The coalescence behaviour of bubble pairs was recorded using high-speed video imaging in which information such as the coalescence time and the deformation of the resultant bubble upon coalescence could be extracted. The results were then compared between the different surfactants for several concentrations. It is shown in a study that the coalescence time increases with surfactant concentration until the Gibbs-Marangoni effect is suppressed by bulk diffusion. Conversely, the oscillation of the resultant bubble was found to be affected only at concentrations at which the film is saturated. The implications of the effects of surfactant type and concentration on the coalescence time and bubble oscillation in froth flotation are discussed. Keywords: froth flotation, frother, bubble coalescence

Sep 1, 2012

By S. M. Bradshaw, C. Dorfling, F. Ngandu

"Selenium removal and platinum group metal (PGM) recovery from copper sulfate leach solutions form an integral part of platinum producers’ base metal refinery operations. Recent studies found that substantially higher PGM recoveries can be achieved if excess thiourea instead of sulfurous acid is used as precipitation reagent; however, the impact of the proposed process on downstream processes was unknown. The objective of the current study was therefore to investigate the effects that excess thiourea and residual selenium present in the rich copper sulfate electrolyte have on copper electrowinning. This was achieved by performing cyclic voltammetry tests using a platinum rotating disk as working electrode, a graphite auxiliary electrode and a saturated calomel reference electrode. A synthetic copper sulfate electrolyte containing 0.01 M Cu2+, 1 M H2SO4 and varying amounts of selenium (20 – 150 mg/L) and thiourea (10 mg/L and 100 – 300 % excess) was used. The results obtained have shown that both thiourea and selenium interact with the cupric ion cathodic reduction reaction. Thiourea polarized the working electrode and lowered the efficiency of the cupric reduction reaction. Tests on the solutions with high selenium concentration showed simultaneous reduction of copper and selenium, which led to copper selenide formation. Nodule formation on the deposit surface also became significant at higher selenium concentrations. Based on these results, it was concluded that precipitation of PGMs from the copper sulfate solution with excess thiourea is not feasible due to the detrimental effect on downstream electrowinning operations.INTRODUCTION During the high pressure oxidative leaching stage in a typical base metal refinery (BMR) circuit, selenium, tellurium and some platinum group metals (PGMs) are dissolved along with the desired copper ions. The impurities (selenium and tellurium) may pass to the copper electrowinning circuit where it can result in the formation of nodular copper electrodeposits or reduced current efficiency. The presence of PGMs in solution, on the other hand, increases the precious metal inventory and potential losses of the operation. Currently, sulfurous acid is widely used for selenium and tellurium precipitation from copper sulfate leach solutions. Sulfurous acid is capable of reducing cupric ions to cuprous ions; the generated cuprous ions then react with Se4+ and Se6+ to precipitate selenium as a copper selenide (Bello, Dorfling, 2014). Recent studies have, however, proposed the use of excess thiourea as a precipitating agent for the removal of selenium and tellurium; it has the advantage of improved PGM recovery in the Se/Te precipitation step (Lottering, Eksteen et al., 2012; Mulwanda, Dorfling, 2015)."

Jan 1, 2018