Search Documents

By P. Prakash

A dual-drive planetary mill, which has a rotating shaft that sweeps a circle of diameter 750 mm, has been designed. The planetary mill is powered by a 5 hp motor to rotate the main shaft and a 3 hp motor to rotate the jars. The charge dynamics inside the horizontal-axis planetary ball mill was established using three-dimensional DEM simulations. The simulation results provided data to determine the impact energy distribution and the effect of process parameters such as mill speed and filling. It has been observed that the mean impact energy per unit time increases with rotation-to-revolution ratio, whereas the average number of inter-particle impacts per unit time decreases. The mill was also used to synthesize a variety of powders. Here three case studies of reaction milling are briefly presented: (i) cementite and silicon carbide, (ii) oxide dispersed strengthened (ODS) steel, and (iii) magnetite from blue dust. In each case, the powder was produced by mixing and then milling the corresponding pure components. The phase evolution, particle size distribution, and morphology of particles during milling were studied for various samples collected at different milling times using laser size analyzer, SEM, TEM, and Mössbauerspectroscopy. The results established a convenient way to produce powders of high technological and commercial value.

Sep 1, 2012

By Wayne van Drunnick, Mervyn Ruthnasamy, Olvier Guyot, Christophe Bouché

"Anglogold’s Mponeng Mine is situated in South Africa’s North West Province approximately 80km from Johannesburg. The reefs being mined in this area are among the deepest deep level mining operations in the world. These shafts often exceed several thousand meters making these operations complex and expensive.The gold plant is fed with run-of-mine ore which is stored in mill silos. Feedrate to the mills is controlled by a variable speed belt. Three parallel SAG mills (4.85 x 9m) treat 80-100tph, operating in closed circuit. Hydrocyclones classify the mill discharge, returning the oversize to the mill feed. Cyclone feed density and pressure are measured and are used with typical control loops to determine water addition rates to the mill. Control loops at PLC/SCADA level were historically used with limited success in the control of the milling circuits. Mill control for an installation of this type used mill mass (measured by load cells) and feedrate to control throughput. An online particle size analyser (PSI) was installed to assist grind control in tandem with pressure/density control on the cyclones. Although the accuracy of the measured grind was reliable, long term consistency of the PSI could not be guaranteed. Economic pressure from the business sector requires consistent mill throughput at optimum grind conditions. Fluctuations in production targets can manifest due to inconsistent control and the lack of real-time information from the process.This sensitivity to process movements may vary between shifts and also with changes in ore competency.Whilst tools are available to improve control, few have the sensitivity to process movements to provide real-time information for optimal grind control. For this reason an Advanced Control solution was sought. Advanced Control is often described as the supervision of basic PLC/SCADA control. Advanced control systems have to seamlessly compliment the existing control strategy and bridge the gap that exists between basic control and optimised control. A solution was found in the Metso Minerals CISA’s OCS (Optimising Control System). This French designed system makes changes to process setpoints to achieve peak performance and is distinguished from others by its soft sensor capabilities. The soft sensor is an embedded module in the OCS package that can be configured to estimate values normally obtained from field instruments. Advanced control using a Fuzzy Expert System assisted by Statistical tools (such as moving averages and a Soft Sensor using Phenomenological Models) would serve to bridge that gap. Metso Minerals CISA’s OCS is a modular system with various capabilities.It was successfully used to provide on-time process information via Soft Sensors. Circuit stability was achieved using Rule Based Expert Control in complete synergy with Fuzzy Logic. Two rule-based strategies were developed for this circuit. The first uses the online product size analyser as a primary control variable. The second uses a calculated kWh/t value and a modelled mill discharge density as primary control variables. The latter had more availability than the particle analyser and is currently in use."

Jan 1, 2003

By M. H. Moys, H. Dong

"Discrete Element Method (DEM) has become a standard tool to simulate grinding mills in order to gain information about load behaviour, power drawn, etc. However, parameters necessary to run a simulation are not always readily available. For example, the coefficient of restitution used in DEM simulation from the literature ranges from 0.1 to 0.9 due to lack of accurate values. The lack of correct input parameters results in the fact that some simulation parameters are adjusted to match the simulation prediction with the experimental results. It is inappropriate to tune one single parameter arbitrarily in order to fit the prediction with experimental results. The correct value of parameters for DEM simulation should be established, and rigorous validation on simulation results by DEM needs to be done.The objectives of the ongoing project are to measure the coefficient of restitution at conditions analogous to grinding practice. Equipment has been built to measure the coefficient of restitution. A typical case of impact test showing the vertical position of a ball as a function of time is presented in Figure 1. The coefficient of restitution between steel ball of different sizes and the targets including steel liner (e = 0.91), mild steel block (e = 0.57) and rubber liner (e = 0.7) have been measured. The coefficient of restitution reduces to 0.38-0.52 when there is a layer of coal particles (1-2 mm) on the steel liner. The effects of ball size, drop height on coefficient of restitution are investigated. Then a DEM code is developed of several contact models to simulate the impact process. This code can reveal details on velocities (translational and rotational) and forces (normal and tangential) during the brief impact interval. Figure 2 is a comparison of the rebound rotational velocity between experiment and prediction by different models. The results can be used as DEM input and to assess contact models."

Jan 1, 2003

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

A new flotation system has been developed to improve the generally slow separating differentials of fine bubbles and fine particle suspensions. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. In the new system (see figure 1) this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.

Jan 1, 2003

By Sashnee Raja, Mehdi Nemati, Ashley Sissing, Susan T. L. Harrison

"Extreme thermophiles, operating at 65 - 90°C, are finding increasing application in biohydrometallurgy. These micro-organisms have the advantage of exhibiting better oxidation kinetics in terms of reaction rate and extent of mineral solubilisation (Duarte et al., 1993; Norris and Barr, 1988; Konishi et al., 1995). These extreme thermophilic Archae, characterised by a different cell envelope structure (König and Stetter 1986, König 1988, Michel et al. 1980) perceived to provide reduced structural strength in comparison to bacterial envelopes, and customised metabolic pathwaysThe active tank bioleaching process, used for high rate leaching, is conducted in a slurry bioreactor. Here sufficient energy dissipation is required to ensure suspension of the mineral phase as well as to sustain high rates of gas liquid mass transfer. It is well known that subjection to hydrodynamic stress of sufficient magnitude may alter the physiological state of a range of micro-organisms through changed viability (ability of the microbes to grow), metabolic activity and integrity. While limited study on the influence of the solids phase on thermophilic leaching performance is reported, initial reports suggest that the thermophiles used for bio-oxidation appear to be sensitive to hydrodynamic conditions (Jordan et al 1993, Clark and Norris, 1996) and the presence of solids (Norris and Bar 1988, Le Roux and Wakerley, 1988, Escobar et al. 1993, Torres et al. 1995, Nemati and Harrison, 2000)."

Jan 1, 2003

By Stephen J. Harker, John Knights, Randolph A. Pax, Glen A. Stewart

"Mineral samples were obtained from different stages of a mineral processing circuit used to extract the copper and gold rich mineralogical phases. The aim of this work is to characterise the quality of the samples at different stages of processing. The samples were taken of the head grade, tailings, cyclone overflow and the final concentrate.Characterisation of the samples was determined using Cu-Ka X-ray powder diffraction and Fe57 Mossbauer spectroscopy. These measurements will be presented and discussed in terms of the enrichment of the ore, showing the removal of magnetite and quartz through the processing, the final concentrate being rich in chalcopyrite and pyrite. This data also shows the utility of Mossbauer spectroscopy to provide mineralogical phase information directly.Mossbauer spectroscopy is a tool to determine the material phases of a sample. It is a nuclear based technique which measures the amount of attenuation of a narrow Doppler shifted source energy as it passes through a sample. The attenuation depends on the amount of resonantly absorbing material in the nuclear radiation path from the source to the detector. Synchronous detection of the doppler shifting velocity and the nuclear radiation count gives a Mossbauer spectrum. By convention, the energy axis of the Mossbauer spectrum is displayed in units of velocity.Figure 1 shows Mossbauer spectra obtained for a sequence of samples throughout a processing plant. These spectra show the removal of magnetite and the concentration of chalcopyrite and pyrite. Optical microscopy results indicated a significant component of bornite not witnessed with Mossbauer spectroscopy. Closer examination showed that optical microscopy assays over estimate the bornite component."

Jan 1, 2003

By C. Suazo, N. Mora

"The bubble size distribution plays a fundamental role in flotation kinetics. Nowadays it is possible to measure the bubble size distribution, gas holdup and superficial gas velocity by using specialized equipment developed for this purpose. In this article a methodology is presented for estimating the kinetic rate constant using a known particle and bubble size distributions. The attachment and detachment probabilities were modelled from three matrixes. The first matrix represents particle size distribution, the second was named the probability matrix, and the third is the bubble size distribution. Using laboratory data, it has been possible to estimate the flotation rate constant as a function of operating conditions and both the bubble and particle size distributions. The model tested at laboratory scale achieved a quadratic correlation coefficient equal to 0.97. This methodology could be used in the operation and control of the flotation, when in the near future we have industrial equipment that allows in-line measurement, in real time, of gas dispersion and bubble size distribution. knowing particle size distribution, it will be possible to manipulate the operating flotation cell conditions, in order to modify the bubble size distribution and find the bubble distribution that maximizes flotation kinetics. Furthermore, knowing the bubble size distribution, the grinding operator will be able to look for the particle size distribution that produces the maximum flotation kinetics. In order to do this, the operator will have to modify the solids percentage fed to the hydrocyclone cluster, modify the apex/vortex ratio, etc. Finally, this article shows that the maximum flotation speed is reached when the particle size distibution slope is equal to the bubble size distribution slope."

Jan 1, 2014

By K. Ananth Krishnan

Today we see a paradigm shift in political, environmental, and economic trends, which are challenging the mining industries. It is very clear that these issues are reaching unparalleled scale and complexity. Cost efficiency and corporate social responsibility are the two primary drivers for the mining industry today. The current challenges facing the industry include: ? Due to deterioration of quality of ores, the scale of operations has become humongous which necessitates high degree of automation and remote operations ? Scarcity of skilled manpower and the necessity to minimize employment of humans at unsafe locations ? Automation of routine activities, improving the efficiency of operations and reducing the cost of production ? Land, water and energy have become scarce in most of the resource rich regions In the current macroeconomic conditions, it is obvious that the industry is under tremendous pressure and it is imperative that the industry embraces sustainability, enhanced energy efficiency, and improved resource allocation. Closely related sectors like energy and utilities have set an example by acknowledging the need to alter their business practices to meet the essentials of sustainability, adoption of new operating models, policy and regulation structures. There is a need to continuously optimize the operations across the entire process value chain as well as across geographies in order to meet the market demand while dealing with supply chain constraints. The goals of optimization could be enhancement in productivity, reduction of production costs, carbon footprint, etc. The gamut of operations is vast, starting from exploration to mining, mineral processing, smelting, refining, casting, rolling (deformation processing), heat treatment, and finally manufacturing of industrial products / components. Advances in information and communication technologies (ICT) in combination with modeling and optimization tools have made it possible to address these issues in a quantitative manner based on real life data. Manufacturing industry, for example, has successfully leveraged these technologies (ERP, PLM, MES, APC, etc.) to enhance productivity and quality. In this presentation, I would like to illustrate the benefits that could be derived by implementing ICT-leveraged solutions available today for the mining industries. I will focus on the following recent technological developments in the context of their applications in the mining and minerals industries: Mobility technologies: The industry is looking for strategically sustainable solutions that fit the working profile of mining engineers and which provide up-to-date information in real time. Mobile applications for iPhones and iPads are gaining popularity, which is helping mining engineers to work on-line as well as off-line. Mobility technologies have made it possible to provide data anywhere and anytime in a form you prescribe. This enables proactive responses to changing dynamics of the marketplace. For example, a plant engineer can access information about any critical process equipment, monitor its performance and do the needful as and when needed. Similarly, scheduling of operations can be optimized based on the market demand and on the availability of raw materials, labor, and status of equipment.

Sep 1, 2012

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By Paula Olea, Gonzalo Montes-Atenas

Froth flotation operation is a large tonnage process aiming at selectively separate economically valuable minerals from gangue material. The wellbeing of an industrial froth flotation operation has been historically assessed and understood in terms of many variables known to somehow affect the process performance. Among these variables, air dispersion have been pointed out as key to secure the correct transport of hydrophobic particles to the froth phase and, then, to the concentrate. One of the classic parameters assessed when evaluating the air dispersion in flotation tanks is the superficial gas velocity. Many reports have focused on studying the superficial air velocity profiles across the pulp phase and theories have been based on the fact that the measurements should be performed in the so called "quiescent zone", which is a volumetric region inside a flotation cell of difficult determination. The hypothesis behind this research work is that the reporting of particles to the concentrate would provide a better correlation with the effective air flowrate pattern created in the froth phase. The aim of this study, as a first step towards developing a flotation model fully froth phase-based, is to estimate the effective surface area used in a flotation cell derived from results obtained with a specific setup at laboratory scale. The methodology considers running a thin lateral flotation cell cut at different superficial air velocities, with and without particles. It was found a non-linear correlation between the superficial air flow rate and the characteristic distance between the vertical wall next to the cell lip and the cut point where the foam or froth flowrate almost stops contributing marginally to the overall amount of solid particles transferred to the concentrate. The presence of hydrophobic particles reduced the mobility of the froth phase reducing the characteristic distance.

Jan 1, 2014

By Hernán Menares, Diego Hernández

"Over the last few years, the copper mining industry has been facing a changing scenario with respect to both the market and society which has resulted in taking a closer look at the way in which mining is being done. The cycle of high metal commodity prices of the last decade left the industry with high costs. Together with increased environmental and social requirements, a decrease in ore body quality, scarcity of resources such as human capital, water and energy, has resulted in an ever-increasing challenge to make a profit out of new ore bodies but also to maintain the current operations in the longer term competitive. The major challenge is to create value for all stakeholders, exploiting ore bodies that nowadays are not considered economically attractive, which applies to both new ore bodies and existing operations, but in a sustainable way. In order to achieve this objective, it is necessary to approach the mining business differently in five main areas: (1) operational efficiency through better use of installed equipment and skilled labor force; (2) efficient use of energy; using opportunities for alternative energy sources and efficient design; (3) efficient use of water; diminishing losses and use of seawater as an alternative source; (4) minimizing environmental impact by eliminating effluents and controlling dust emission; and (5) a more closer, proactive and collaborative relationship with the communities allowing them to be an active player in the solution to assure a sustainable business in the long term. This presentation will show how Antofagasta Minerals is facing these challenges with a long term strategy that includes all of the above mentioned aspects and that is allowing the company to exploit its mineral properties in an efficient and successful way."

Jan 1, 2014

By Remmerswaal, U. Boin, M. B. G. Castro

"To design sustainable products that can be recycled with high resource efficiency, low environmental impact and economic feasibility, the choice of materials and materials combinations, made in the design stage, is fundamental. The products we design, manufacture and use now will be the resources of the future. Designers are able to select materials for a product according to the many functional requirements they must fulfil. But they have a limited knowledge of the recycling processes and its requirements regarding quality of the secondary material streams. Resource Engineers have to manage the processing of these streams, that are becoming more complex with the increasing variety of materials and decreasing size of components. After mechanical separation of the materials streams resulting from shredding of EOL (endof- life) products, there is always a degree of contamination, from two possible causes:Incomplete liberation: the bonds between different materials combined in a component are not completely destroyed by shredding, resulting in some particles containing two or more materials attached;Separation efficiency: the mechanical separation processes are not able to separate perfectly the many material particles; there are always a number of foreign particles in the recovered streams.Sometimes, those contaminants cannot be removed by the industrial metallurgic recycling processes, and a more serious problem occurs when the contamination levels compromise the recycling of the material stream by lowering its quality (i.e. the properties of the recycled material will be lower due to the contamination). As a consequence, the material must be diluted in virgin raw material and/or used in a less demanding application (downgrading), causing resource depletion and increased energy use, waste production and recycling costs. In order to make the best choice of materials combinations for a product, a systematic approach is necessary, that can close the gap between the knowledge areas of Product Design and Recycling Technology."

Jan 1, 2003

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003

By R. Els Ellis

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

By R. Bugueño, W. Calderón, G. Montes-Atenas

From the point of view of industrial performance of metal extraction, the efficiency of a column leaching operation depends strongly on the leaching agent and the ore properties such as mineral composition, mineral liberation and particle size distribution. One aspect that has become particularly important is how the leaching solution flows through the porous structure which contains the valuable minerals. It is known that the output flow rate of leaching solution depends mainly on factors of the input flow, environmental condition and porous bed properties. The latter factor is often evaluated and reported under saturated conditions but in practical leaching systems unsaturated conditions are dominant. This investigation has the purpose of determining the residence time of the leaching solution in columns with different diameters under unsaturated conditions by using experimental data and numerical simulations. Laboratory leach test were performed using isothermal jacketed columns with top cap to reduce the evaporation. The simulations were performed using the software SVFlux® which incorporates material properties such as Soil Water Characteristic Curve (SWCC) and Unsaturated Hydraulic Conductivity. Preliminary results indicate a non-linear asymptotic behavior of the saturation rate with respect to the operation time. Results from numerical simulations show the same non-linear behavior and a considerable delay between input and output flows. Further analysis concerning with the effect of transpiration and evaporation mechanisms is discussed.

Jan 1, 2014

By Rod Hocking, Nenad Djordjevic, Randolph A. Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures from standard operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill. Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulate the assemblage of a physical mill.By modelling the assemblage of steel balls in a 1 m pilot mill and duplicating the experimental arrangement exactly with the PFC3D model, it was possible to replicate the pattern of falling balls in the experimental mill. Furthermore, the key features of the acoustic emission spectrum that was calculated compared favourably to the measured spectrum at low frequencies. The experimental spectrum is shown in Figure 1."

Jan 1, 2003

By Francis Pitard

"The optimization of metallurgical processes requires an in-depth understanding of the heterogeneity carried by any constituent of interest. It emphasizes that knowledge of the Theory of Sampling (TOS) is the necessary step to ensure that valuable and valid research programs, pilot plants, feasibility studies, plant design and plant operations have been set on solid foundations. Too many publications today are solely based on the properties of the sample, with no mention of how this sample relates to anything in the environment where it was collected. Unfortunately sampling is an error-generating process that leaves no apparent tracks of its shortcomings. Indeed, it is easier to track down analytical errors than sampling errors. Consequently, bad sampling practices plague the scientific community and the industry and are responsible for severe money losses, unsatisfactory science and processing, and sometimes litigation. A point-by-point strategy is presented addressing sampling problems in early stages of a project. Sampling system requirements for metallurgical accounting and process control are listed. The use of Chronostatistics is suggested to determine if sampling systems are performing satisfactorily and to identify the various types of process variability that may not be easily detected by a conventional inspection of available chronological data. This strategy will help engineering firms, manufacturers, managers and supervisors to provide, install, use and maintain key sampling systems located at very important points in a process. Equipped with the appropriate sampling and statistical tools it becomes easier to minimize reconciliation problems with the mine, with suppliers and with clients. Contrary to the beliefs of many people, good sampling systems are not expensive because in the long run they help to reduce hidden cost and better regulate plant productivity; they most certainly minimize the number of unnecessary meetings looking for solutions where there are none. The suggested strategy will help specialists to extract maximum information from the available data, as large investments and crucial decisions depend on it."

Jan 1, 2014

By A. Collings, A. Farmer

"Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation, which is the formation and sudden collapse of bubbles in a fluid. Cavitation occurs preferentially at solid surfaces in a liquid: at container walls, inserted objects or suspended particles. When the cavitational bubbles collapse near a solid they do so by forming a very high energy jet directed from the point on the bubble furthest from, and directed towards, the surface of the solid, in effect micro jet blasting.This paper highlights some of the major mineral processes where ultrasonics is beneficial namely: Surface cleaning of detrital mineral particles, where container quality glass sand was upgraded to tableware quality and up to 20% improvements in the sharpness of high tension separation of mineral sands was achieved"

Jan 1, 2003

By G. S. Hansford, G. E. Searby

"Ferrous iron oxidation kinetics was measured in continuous culture at temperatures between 65 and 75ºC, using thermophilic microbes suitable for high temperature bioleaching. The resulting specific oxidation rates were modelled as a function of the ferric/ferrous iron ratio. The results were compared to those obtained by conventional mesophilic microbes.Microbially mediated ferrous iron oxidation is a vital sub-process in the mesophilic bioleaching of sulfide minerals and is expected to be of similar importance at elevated temperatures using thermophilicmicrobes.A thermophilic archaeal culture used in chalcopyrite bioleaching was successfully grown in continuous culture on ferrous sulfate, indicating the capability of the microbes to sustain growth for long periods on the energy provided by the conversion of ferrous iron to ferric iron, the primary leaching agent in sulfide mineral bioleaching.Steady state data was obtained at residence times of between 70 and 10 hours, with washout occurring at residence times between 11 and 9 hours, corresponding to a maximum growth rate (µmax) of between 0.09 and 0.11 hr-1. The reactions were followed by measurements of the solution redox potential, soluble iron concentrations, and offgas analysis of the oxygen and carbon dioxide utilisation rates."

Jan 1, 2003

By M. Özer, G. Önal, F. Arslan

"The use of ultrasonic in industrial processes has increased during the last few years. Ultrasonic vibrations are used in sieving, grinding, ore washing, cleaning, and flotation in mineral industry. There are also some attempts for the utilization of ultrasonic treatment in separation and removal of fine particles from gases and liquids. In Kalemaden A.S. (Turkey) four different types of clay mixtures (1. A mixture of clays from Balikesir-Düvertepe and Istanbul-Sile, 2. A mixture of clays from Ukrania and Balikesir-Düvertepe, 3. Sögüt-Kadikelimesi, 4. A mixture of clays from Sögüt and Istanbul-Sile) and kaolin from Balikesir-Düvertepe (Turkey) are concentrated before their use in ceramic production. Dewatering is the important step in those types of concentration plants. Sedimentation of concentrated clay has always been difficult and taken long times due to their nature and having small particle sizes. Flocculants can be used to enhance the sedimentation, but they are not preferred by the ceramic industry since they affect the quality of ceramic products. For this purpose, ultrasonic treatment is used in the sedimentation of clays mentioned above for solving the problems encountered related to the ceramic industry and promising results were obtained.Kaolin sample, subjected to this experimental study, from Balikesir-Düvertepe region of Turkey was brought from the plant as a pulp in containers and throughly mixed with a stirrer before sedimentation experiments. A two liter graduated cylinder and an ultrasonic bath (with 25 kHz frequency and 0.5 KW power) were utilized in the tests. Superfloc A-120 (1% concentration) was used as a flocculant. The settling distance was reported against the settling time during the experiments. Initial and final pulp densities were also determined. The effects of several parameters such as pulp density, flocculant addition, and ultrasonic treatment on the sedimentation of kaolin were investigated and the results are represented in terms of settling distance versus settling time."

Jan 1, 2003