Search Documents

By Naim Noori Samie

Lateral force rsistance of piles is analytically investigated by dividing the pile length to 3 segments. The first segment (Zone I) models the load eccentricity with respect to the soil and the pile-deck connection, using a third degree differential equation representing the shear variation along the pile. The soil is assumed to be uniform, homogeneous with an elastic-perfectly plastic behavior. The Top soil layer (Zone II) is assumed to be stressed beyond the elastic limit. A simple 4th degree differential equation represents this zone. The soil resistance is assumed to vary linearly with depth (or surcharge). The pile deformation and soil behavior determines the plastic zone length. In zone III the soil is assumed to behave elastically, hence its resistance is proportional to its deformation. A linear 4th degree differential equation is employed in this zone. The compatibility conditions are satisfied on each boundary. Maximum allowable moment and shear are investigated throughout the pile as the basic limiting criteria on lateral force capacity. In this paper the soil coefficients are taken from a proposal by ref(3), and the results are compared with the soil response as determined by the P-Y method as recommended by ref(2).

Jan 1, 1996

By Subrata Ray

A large no of power stations are being set up in Chandrapur area having coal deposits. Several industries are also coning up in this area. The subsurface is geologically formed under Gondwana system and consists of shale strata at depths ranging from 8 to 12 m. The stress deformation characteristics of shale exhibits wide variation because of it's geological origin. In view of this, a study was conducted on bored cast in-situ piles installed for a Switch yard project to evaluate load settlement characteristics of three test piles to understand the probable engineering behaviour of the material at the tip and the sides. An approach is developed to simulate the load settlement behaviour as observed in the field, theoretically. This is based on the concept of load transfer. The fit is obtained by varying the parameters, thus may be considered as iterative in nature. The theoretical curves closely matched the observed curves. The results of this study are presented in this paper.

Jan 1, 1996

By Clarissa Aguiar, Seok hyeon Chai, Thamer Yacoub, Sina Javankhoshdel

Sheet piles are used as an excavation support for soil retention. They are interlocked systems to form a wall for earth support along with anchors to provide an extra lateral support in excavations. The earth pressure against a sheet pile structure is not unique for each soil, but rather a function of soil-structure system. Movements of the structure with respect to the soil are primary factor in developing the pressure and thus the problem becomes indeterminate. In order to model a sheet pile wall for the analysis, structural element/interface can be used for the sheet pile. However, the use of the structural element with soil model alone is insufficient to simulate this soil-structure system as it fails to capture the slip condition between the sheet pile and the retained soil. In order to capture this slip condition, an interactive element can be used between sheet pile and soil to allow slip to occur. There have been many case studies where this method was used to analyze the response of the retained soil. Numerical studies have shown a good agreement with experimental results, but this stiffness is often not a well-known parameter, due to its complexity in nature of interactive behavior between soil and sheet pile walls. Also, many case studies are carried out with twodimensional analysis of the foundation, where three-dimensional analysis may be more suitable in some practical applications. In this paper, the interactive behavior of the element between sheet pile and soil is investigated with case studies for staged excavation using sheet piles and anchors. Then, investigation of a three-dimensional model is carried out by comparing with two-dimensional analysis.

By Teresa M. Bodas Freitas, Arianna Lupattelli, Peter J. Bourne-Webb, Diana Salciarini, Martina Zito, Donatella Sterpi

The thermomechanical response of thermally-activated (TA) piles under monotonic thermal loads is quite well understood and the remaining uncertainties relate to the effect of long-term, cyclic loading of individual TA piles and pile groups. Recent studies undertaken by the authors have provided insights into the behaviour of TA pile foundations undergoing cyclic thermal loading. Despite their simplicity, the analyses show that key aspects of the observed response of piles in sand, under cyclic thermal loading can be reproduced, providing confidence in the outcomes of the analyses. The studies examined isolated piles and pile groups, and concluded that irrecoverable thermally-induced settlement may be mitigated through the choice of an appropriate margin of safety on the pile shaft resistance under service mechanical load conditions, and the maximum thermal stress can also be readily estimated. This paper consolidates these works and provides guidance regarding the safe geotechnical and structural design of the piles, then looks towards the remaining issues around the safe provision of thermally-activated pile foundations.

May 1, 2022

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

The city of Naruto in the southwestern part of Japan is situated at the mouth of the mighty Yoshino River. An approximately 1,000m-long levee/bulkhead along one of the river’s tributaries in the city was raised with prefabricated steel panel walls on a concrete base bulkhead. Some sections of the walls’ foundations were combi-walls made of sheet pile cut-off walls and interspaced pipe piles; both of which were installed with press-in piling because the new wall alignment was very close to existing homes and businesses. A Clamp Crane, which clamped onto already installed piles and moved forward and backward on them, was utilized for a segment where the access to its piling location was too tight for a conventional crane or a track-mounted pile driver to maneuver.

Sep 8, 2021

By Sastry Putcha, Santosh Mummaneni, Avasarala Swamy

"Inspection of bored pile hole bottom prior to placement of concrete is one of the most crucial element of foundation design and construction, especially for end bearing piles. Pile hole bottoms that are not cleaned well for sediments could potentially result in settlement. Although many projects have specifications in-place for drilled pile hole inspection, they are rarely implemented as the current available tools are either unsafe or cumbersome and costly, thus making it very unattractive for owners and contractors. Further, sometimes the post-construction nondestructive quality control testing such as PIT or sonic logging on piles resulted in unanswered questions related to soft bottom. This generates costly disputes with additional testing including concrete coring and possible repairs. Currently, there are several bored pile bottom inspection devices in USA, namely, SID, DID, and SQUID which can either provide video and photo documentation or measure sediments.“ShaftCam”, a patented advanced Digital Borescope, was invented to address the issues related to pile hole bottom inspection with its ability to measure sediments as well as photo and video documentation. Shaftcam device consists of 8-inch diameter bell with a camera, led lights, air hose connection and penetrometer with digital measurement that are connected to a control power box and laptop through a cable. The bell is fitted with a round clear open fiberglass skirt to form an open chamber. A simple motorized winch frame allows the user to lower the ShaftCam equipment gently to the bottom of the shaft at the desired location. Once the bell with camera is lowered to the bottom of the hole, air is pumped into the clear chamber to displace the water/slurry/polymer and get a clear view of the hole bottom to record the conditions and measure the sediment thickness and resistance. The skirt can also be enclosed and lowered to the desired location to allow for inspection of shaft walls.ShaftCam weighs less than 15 lbs. (6.8 kgs) in water and allows for inspection of the hole by one person in less than 30 minutes. Use of ShaftCam has saved significant time and money and thus allowed owners and contractors to readily accept and implement the quality control measures in many projects in USA over past few years."

Jan 1, 1900

By Alessandro Bertero, Manuel Toniolo, Vincenzo Tirozzi

"The installation of foundation elements (large-diameter Bored Piles or Diaphragm Walls) for the execution of underground works to be performed through the ""Top Down"" Technique (Stations, Car Parks, Subways, Artificial Tunnels) often requires the insertion, with pinpoint accuracy, of steel or prefabricated elements within the foundation system, to provide temporary and/or permanent support to the whole structure.The future high-speed railway station of Florence Belfiore (Italy) is a perfect example; the new station will be built in the Northwest area of Florence, about two kilometers far from the existing station of Santa Maria Novella. The project envisages installation of about 500 bored piles (1200-1500-2100 mm diameter), with lengths ranging between 50 and 70 m. In the upper inner part of 250 piles, a steel pipe (weight: 15-20 tons, length: 22-25 mt.) has to be inserted with pinpoint accuracy.The “TREVI-CALATORE” system allows to install the plunge columns and adjust their position and verticality.INTRODUCTIONThe execution of underground works via the ""Top Down"" technique, train or tube underground stations, parking shafts, tunnels, often implies the need to carefully insert steel or prefabricated structures, serving as provisional/definitive pillars, into the foundation elements.The future high-speed railway station of Florence Belfiore is a perfect example; the new station will be built in the Northwest area of Florence, located about two kilometers far from the existing station of Santa Maria Novella.The new Belfiore Station is part of the new European high-speed railway network. The works related to Florence urban penetration include (figure 1):•,a 6.5 km. twin tunnel excavated via TBM/EPB, that will run beneath Florence in a north-east direction,•,passing under more than 150 buildings, many of which can be considered historic buildings, with a soil•,coverage ranging from 6 m to 20 m;•,a North portal in Rifredi area, Firenze Castello Station;•,a South portal near Campo di Marte Station (which is also the launch shaft of the TBM)•,the new Underground Station in Belfiore area."

Jan 1, 2016

By Ramdane Bahar

The new Algiers airport building is a reinforced concrete building of more than 80 thousand square meters of floor slabs. It is located at Dar-EI-Beida, near the old passenger terminal, about 20 km east of Algiers. The project is designed to receive about six millions passengers annually and leaves the possibility of future extension. Due to the presence of a top layer of compressible soil and great concentrated loads transmitted to the foundations, the building is to be founded on 1730 bored piles of 1.2 meter diameter varying in length between 14 and 28 m. Construction work started in 1986 and was interrupted in 1996 due to financial difficulties when the structure was almost complete. The structure was left unattended for more than three years without any weatherproofing and in 1999 a new firm was appointed to complete the work and hence an evaluation of the existing structure was necessary. This paper describes and discusses the foundation design, construction supervision, site quality control and assessment by the parallel seismic method of the deep foundations built in cohesive soils. The variation in soil conditions and identified geotechnical and hydrogeological problems associated with the development of the area, required a thorough knowledge of the soil conditions. A variety of tests, involving more than 200 locations, were carried out. The ground investigation, pile tests as well as different problems encountered during piles construction, are presented.

Jan 1, 2002

By K. Rama Sarma

Piles are frequently subjected to lateral forces and moments in addition to vertical forces and hence the piles have to be designed for both lateral loads as well as vertical loads. In the design of such pile foundations, two criterias must be satisfied. First an adequate factor of safety against ultimate failure and second, as acceptable deflection at working loads. In this study the work has been carriedout to study the lateral deflection pattern of the pile. The solutions to the problem primarily depend on soil modulus. Equations for computing the values of slope, deflection and coefficients for many types of soil conditions have been developed for static loading for long piles. As analysis part is not available for the above methods for the values of depth coefficients in the tables. It is required to go for linear interpolation which is not valid and highly unreliable. In this present method, coefficients can be obtained for any value of depth coefficient (z) with simple calculation. The present method is very concise and allows one to ana­lyse any type of pile with varying depth coefficient (z) even without the availability of any practical data regarding applied lateral load (P1) and moment (M1).

Jan 1, 1996

By W. Morgan NeSmith

"The DFI ACIP Pile Committee, in conjunction with the Florida DOT, completed an ACIP Pile installation monitoring and performance test program in late 2016 to advance the inclusion of ACIP piles in future specifications for bridges by state agencies. Piles of different diameters were installed for compression, tension and lateral testing, and one pile was extracted for visual inspection. This paper presents the pile installation, non-destructive testing and load test results of the program.INTRODUCTION The Deep Foundations Institute (DFI) Augered Cast-In-Place (ACIP) Pile Committee performed a ACIP pile installation and test program in the fall of 2016 to demonstrate a fully monitored installation of 18-in and 24-in diameter ACIP piles. The program included automated and manual installation monitoring, Thermal Integrity Profiling, compression, tension and lateral load testing (including monitoring of strain gages embedded along the compression pile shaft), and post-testing extraction of an installed pile for visual inspection.PROJECT DETAILS AND FIELD EXPLORATION A general program location map along with an aerial view of the property in Okahumpka FL is shown in Figure 1. Two Cone Penetration Tests (CPT) were performed at initial reaction pile locations R-6 and R-8 (Figures 2 and 3) The results from CPT R-6 indicated very loose soil conditions at depths below 55-ft, indicating potential relic sinkhole conditions. The test layout was subsequently rotated and moved south of CPT R-8.TEST PILE INSTALLATION DETAILS Seven piles were installed to either 40-ft or 60-ft below grade. Thermal Integrity Profile (TIP) wires were installed in all piles but varied to include one wire each attached to a steel center bar or one wire attached to the steel center bar AND four additional wires (each) attached the steel reinforcing cage installed in these piles. Additionally, the 24-in lateral and compression piles had four steel or PVC casings installed next to the TIP wires for testing by thermal probe and/or wire inserted into the casing."

Jan 1, 2017

By Andrzej Tejchman

A method of improvement of a subsoil under bored pile base by injection is presented. The method employs a special chamber attached to the reinforcement at the bottom of the drilled borehole. The chamber is made of semi-permeable textile bag. The injection entered under high pressure into the bag, causes prestressing of subsoil under the pile base. The results of load tests of piles improved in this manner have shown a substantial increase of their capacity together with simultaneous reduction of settlements. This technology has been implemented for four constructions such as trestle bridges in Gdynia and Warszawa and the bridges in Szczecin and Gdansk. The injection effects are shown based on the load test results.

Jan 1, 2002

By Florian König

It is well known that the bearing capacity and stiffness of displacement piles may increase significantly with time, a phenomenon usually referred to as set-up. In cohesive soils the set-up is commonly explained by consolidation processes in which the dissipation of the excess pore pressures around the pile leads to an increase in effective radial stresses. Recent case histories show that set-up may also occur in sand over a period which exceeds by far the consolidation process. Therefore, other effects apart from the dissipation of excess pore pressures must contribute to this long-term set-up effect. This paper presents the results of a series of multiple pile load tests on prefabricated concrete piles which capture the effect of pile set-up empirically. The main characteristics of the set-up trend are shown with respect to soil type, pile dimensions and distribution over the pile length. Possible reasons for pile set-up like consolidation and stress relaxation after the end of driving are examined using a finite element model which simulates the pile installation process.

Jan 1, 2006

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

Circular secant pile shafts were installed along the tunnel alignments for both the Ohio Canal Interceptor Tunnel project in Akron, Ohio and the Ohio River Tunnel project in Louisville, Kentucky. The diameters ranged from 34 to 51 feet and the depths ranged from 49 to 107 feet. Verticality and concrete volumes were measured on all piles to verify compliance with the design, which for some shafts consisted of a finite element model with multiple openings using unreinforced concrete secant piles. All secant piles were drilled into rock to seal off the groundwater. This paper will discuss the design, construction and quality control of the secant piles for these projects. INTRODUCTION Many Midwest and Northeast cities have Combined Sewer Overflow (CSO) systems which discharge pollutants into waterways during wet weather events. One way to remedy this issue is to provide a temporary overflow tunnel. A temporary overflow tunnel connects to the combined sewer system and collects the overflow during wet weather events, storing the wastewater until the event has subsided. After the storm event, the stored wastewater can be pumped to the treatment facilities and processed as normal. Project Background – Akron, OH The Ohio Canal Interceptor Tunnel (OCIT) project was performed as a result of the Environmental Protection Agency’s (EPA) Consent Decree with the City of Akron, Ohio. This Consent Decree required modification of the existing Combined Sewer Overflow system. The resulting project consisted of a 27- foot diameter tunnel with multiple points of entry to capture the sewer overflow and prevent it from entering waterways. The tunnel is over 6,000 feet long and is as deep as 150 feet below the ground surface; see Figure 1 below.

Jan 1, 2019

By Joshua C. Adams, Les Chernauskas, Edward L. Hajduk

"Drilled shafts are increasingly being used to support bridge and building foundations. Because these foundations usually carry very high design loads and often serve as non-redundant, single load carrying units, these foundation systems need a high level of quality control (QC) and quality assurance (QA) during construction. One such method for providing QC/QA is crosshole sonic logging (CSL) testing, in which ultrasonic signals sent across the drilled shaft concrete assess concrete quality.CSL testing is an effective tool to evaluate the integrity of the in-place drilled shaft concrete. While typically used to evaluate drilled shaft concrete after construction, CSL testing can also be used to evaluate drilled shaft repairs. This application can be difficult, given the variability of repair methods and material properties. CSL testing can also be adversely affected by the condition of the concrete/access tube bond, leading to false anomaly detection and/or inability to evaluate concrete integrity effectively. This phenomenon, called access tube debonding, is often located in upper portions of the drilled shafts where large changes in groundwater occur, such as within tidal zones.Two case histories showcase innovative uses of CSL testing to deal with consistent access tube debonding and to evaluate drilled shaft repairs.CSL OverviewCSL testing involves placing ultrasonic transmitters and receivers in access tubes installed in the drilled shafts prior to concrete placement. Concrete quality is assessed by examining the First Arrival Time (FAT) and relative energy of the signal sent between the transducers. If the distance between the access tubes is known, an apparent signal velocity (i.e., wave speed of the ultrasonic signal through the concrete) can also be determined and used to assess concrete quality.Common CSL testing practice consists of simultaneously raising the ultrasonic transmitter and receiver and recording the ultrasonic signals with respect to depth. This results in a 2D examination of the"

Jan 1, 2009

By P. J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 2010

By Vladimir M. Korolev

The field studies conducted at the experimental-production sites allowed to develop the technology of arranging drilling piles in loess subsiding grounds over 25 m deep and over 250 mm in diameter, to select optimal compositions of flush fluids, to assess the carrying capacity and field of use of the piles under test and to produce a special equipment. The dependence of the ultimate axial pressing-in load on pile driving into the non-subsiding section, its diameter and method of fulfillment, as well as the ground moisture dependence of the specific ground resistance along the piles' side surface within the limits of the subsiding section were determined. The study results allowed to reduce the length of the work piles and the number of bars in the reinforcement frames. The obtained experimental data enable to give a preliminary assessment of the piles' carrying capacity under complicated engineering-geological conditions of subsiding grounds.

Jan 1, 2002

By Zhou Haizuo, Diao Yu, Zheng Gang

"The conventional design method for the embankment supported by DM columns usually assumes the simultaneous failure of all the columns. However, the progressive failure may occur in practice, especially considering that many researches have justified the critical load of DM columns is bending moment. In this study, a finite difference method was adopted to simulate the embankment on soft clay improved by DM columns. An increasing surcharge was applied on the embankment surface to investigate the mechanism of the progressive failure of columns beneath embankment. To capture the brittle bending failure of the DM columns, the model employed a cut-off method, in which the column was separated on failed section as long as the ultimate bending failure was reached. Furthermore, high-strength DM columns were used to enhance the global stability of embankment in this study. The numerical results showed that the ultimate bending failure was first reached at the column beneath embankment toe, and then a continuous collapse extended to the column beneath the embankment shoulder. It is found that the reinforcement could be obviously effective when the reinforced area of high-strength DM columns was extended to a certain area.INTRODUCTIONDeep mixed (DM) columns have been commonly used as a soil-improvement technique to increase stability and to reduce settlement of embankment. Research on failure modes of DM columns owing to embankment fill and surcharge has been the subject of interest for a number of investigators (Miyake 1991; Kitazume 2000; Han 2005; 2006).The potential failure modes of DM column include bending, inclination, shearing, rotating, soil flowing and a combination of these modes (Kitazume and Terashi 1991; Broms 1999). Many researchers have found that bending failure of DM columns was more critical than the shear failure. A centrifuge test was performed by Kitazume (2000) and the results showed that the columns failed in bending before shear failure. In addition, several numerical computations illustrated that design method using the shear strength overestimated the stability of embankment over DM columns (Han and Huang 2005; 2006; Navin 2006; Liu 2007; Wang 1996). In practice, an equivalent shear strength method based on bending failure could better reflect the stability of embankment (Zheng 2010; China Code JGJ79-2011)."

Jan 1, 2015

By Alex Ryberg, Matthew L. Becker

Several integrity testing methods exist which may be used to evaluate drilled shafts. Each test method has advantages and limitations. On occasion, the results from different test methods may lead to conflicting conclusions, making it difficult to conclusively know which results more accurately represent the quality and integrity of a drilled shaft. This case study focuses on the integrity testing evaluation for two drilled shafts which were constructed using permanent casings and installed through flowing river water. Integrity testing was performed using Thermal Integrity Profiling (TIP) and Crosshole Sonic Logging (CSL) on each shaft. During testing, the influence of flowing water and soil layering needed consideration in the collected TIP data. Similarly, concrete curing time influenced the CSL test results and required the CSL tests to be performed multiple times with additional wait times following concrete placement. To aid in the shaft integrity evaluations, Low Strain Integrity testing via the Pulse Echo Method (PEM) was performed on several shafts and concrete coring was also performed to help further assess the acceptance or rejection of the questionable shafts. This paper presents an overview of the testing methods that were applied, their basic methodology, as well as potential limitations that should be considered when evaluating their results.

Sep 8, 2021

By Travis Coleman, Elvis Ishimwe

Currently, more than 400 drilled shafts have been constructed by various contractors at the I-90/94 and I-290 Jane Byrne (Circle) Interchange, located near downtown Chicago, Illinois. Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) tests were performed to evaluate the integrity and concrete quality of the drilled shafts installed at this project. For Phase I of the project the shafts were tested using CSL methods, and the shaft integrity was identified by analyzing the First Arrival Time (FAT) and the signal strength (energy) measurements. For the major portion of Phase II, the Illinois Department of Transportation (IDOT) accepted TIP testing as a substitute for CSL at the request of the contractors. The CSL testing results indicated 54 percent of the tested shafts had anomalies, and 78 percent of these anomalies were located within the lower three diameters of the shafts. To date, TIP testing results indicated the shaft integrity was as expected and acceptable for the all 34 tested shafts. A review of the testing results and a discussion of the detected anomalies are presented. In addition, a comparison of both TIP and CSL measurements is presented in this paper.

By Wanchai Teparaksa

Pile deviation generally can happen after installation of driven pile particularly in soft soil layers. In this case study, all 242 diameter 0.8 m spun piles were deviated from 20 to 820 mm. The large deviation was caused by lateral soil movement in the top very soft clay layer of thickness about 23 m. This very soft marine clay is very sensitive and anisotropic having high water contents of over 120% and low undrained shear strength of 5-10 kN/m2. The remedial works were carried out based on theory of load transfer and soil-structure interaction. All deviated piles were rectified and used as the foundation piles with strictly controlled pile load tests. The construction of a nine-storey building was successfully completed founded on the rectified piles and it has been opened for the service for over two years.

Jan 1, 2002