Search Documents

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; and forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2009

By Herbert F. ?Buck? Darling

A bridge replacement project in Rochester, NY, encountered difficulties when it was determined that rock below one pier was sloping downward toward the river at an angle of 42 degrees versus anticipated 12 degrees. Cofferdam design and construction became very difficult. The unanticipated subsurface conditions delayed the project by eighteen months and increased the cofferdam cost by almost $3.0 million ($US) when direct costs and associated delays were taken into account. The initial approach after discovery of the problem was to use the same type pier design and modify the cofferdam accordingly. This resulted in a cofferdam 12 meters (39.4 feet) deep on the shore side and 18 meters (59.0 feet) deep on the water side. The design used a master pile system to attain required wall strength and used rock anchors to prevent the cofferdam from moving toward the river. The pier foundation was then redesigned by the owner using revised seismic parameters. The original stepped footing carved into rock was replaced by caissons socketed into the rock beneath a large tremie concrete placement. The revised pier and cofferdam designs caused a shift from a mostly land based cofferdam, excavation, and rock removal project into an almost entirely water based cofferdam, caisson drilling, and tremie construction project. These design changes resulted in a reliable, safe, and unusual cofferdam and construction method. All of this was accomplished within a very narrow worksite with a railroad on one side, and the river with its public and commercial freighter traffic on the other. In addition, the existing two-leaf drawbridge was to be maintained in place which put further limitations on the water borne equipment. The engineering and construction considerations, problems, and solutions related to these cofferdams and pier foundations are presented.

Jan 1, 2013

By Leonhard Weixler, Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to construct structural elements in the ground, commonly used for retention systems, permanent foundation elements or deep ground-water barriers, named Cut-Off-Walls (COW). It can be anticipated that global urbanization and increasing demands on environmental considerations will need to be accommodated in underground space in the future. These trends show an increasing requirement for diaphragm walling in even more complex conditions, especially in inner-city applications with limited space. Therefore, there is the demand to minimize the size of equipment to accommodate such projects. Following this demand, a new trench cutter system, the so-called CUBE System, was recently developed. The complete trench cutter system has been fit into container size dimensions so that it can work in very limited space conditions. In addition, complex conditions in terms of space limitations require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistics to ensure smooth production. Due to the limited space requirements, the impact on the surrounding environment is limited. As the system is electric driven, an additional reduction of carbon footprint can be expected. First tests of the system have been carried out and the results will be shared. The paper will explain the construction process and the specific challenges and experiences made for these extreme conditions.

Oct 1, 2022

By Alexandre Alex) J. Bredikhin

"DISCLAIMER: the statements presented herein are those of the author and do not necessarily represent the views of US DoD or its Components.ABSTRACTProgress on the $750M lock project on the Monongahela River was derailed by discovery of large anomalies in the 6.5-7-ft dia. drilled shafts of the new river wall foundation. The anomalies were located 45 to 50’ below the top of the wall at the critical shaft-to-wall interface, and ranged in thickness from several inches to 2-plus feet. A Specialty team, comprised of representatives from the contractor, the Government, and structural design consultants, was formed to evaluate the extent of the problem and the impact on the new lock wall. With no standard method in place, the Government took the lead to develop acceptance criteria for the repairs while the contractor took the lead to identify the repair means and methods. The Government developed a detailed Quality Control plan to capture and document all of the repair data and to approve each shaft repair in a timely manner. This paper provides an overview of the anomalies encountered and the need for repairs; discusses the details of the repair plan; and provides details on the unique quality control measures employed to verify the repairs. By developing and adhering to a detailed quality control plan, the structural integrity of all of the shafts was successfully restored.INTRODUCTIONThe new Charleroi Locks Project is currently under construction by the U.S. Army Corps of Engineers (USACE) in Pittsburgh, Pennsylvania. In the region, the Corps of Engineers is modernizing the series of locks and dams on the Monongahela River. One facet of this modernization is replacement of the existing Locks #4 (aka Charleroi Locks) located upstream of Pittsburgh, Pennsylvania with new and larger capacity locks. The relative location of the project is shown on Fig. 1. The original construction of twin locks (56’x720’ & 56’x360’) and the fixed-crest dam was completed in 1932, with lock walls supported on timber pile foundations. The fixed crest dam was replaced with a gated dam in the 1960’s. The existing lock is undersized and in poor condition and thus needs to be replaced. The project requires the construction of the new river chamber adjacent to the existing land chamber which must remain operational to navigation throughout the construction. In order to accomplish this, the lock walls need to be constructed in the wet. The river wall was constructed using two construction methods referred to on the project as “cofferbox” and “non-cofferbox” construction."

Jan 1, 2017

By Jerry A. Steding

How many times have you heard "You can't drive piles because of the vibration."? You hear these words come out of the mouths of owners, engineers, and contractors. When a piling contractor hears this, he can almost always do a psychological profile of the individual uttering these words of wisdom. If the owner makes the statement, we know the odds are about 95% that the owner owns the building next door or he wouldn't care what happens to it; or the guy next door has threatened to sue the owner if he even so much as walks across the site of the proposed new building. If the owner owns the building next door to the new construction you can also be just as certain the old structure has undergone settlement. If the statement comes from the mouth of the contractor, it is usually just a case of him being inexperienced.

Jan 1, 1988

By Brian Koch

Michels installed 242 drilled shafts to support the piers for a new basket-handle, true-arch twin bridge across the Mississippi River from Moline, IL to Bettendorf, IA. The installation of the drilled shafts was completed with the simultaneous use of two Liebherr LB36 and one IMT 300 drill rigs. Utilizing barges, 233 drilled shafts were installed in the river. Michels crews also installed 7-ft to 10-ft permanent steel casing into the bedrock, and drilled to depths of 60 feet for each shaft. Despite working in strong currents, freezing temperatures and on rocking barges, Michels crews placed the shafts within 3 inches of plan position. Since the drilled shafts are the key piece in supporting the bridge structure, Michels provided cross-hole sonic logging to verify the integrity and strength of the concrete within the shafts and to add another level of quality control for the owner/customer. Extensive planning took place each day to ensure that tugboats, the linchpin of the project, were being efficiently utilized to shift the barges and materials daily. On any given day, Michels transported five concrete trucks by barge from shore to shaft sites to pour between 40 and 240 cubic yards of concrete. The Michels environmental team was diligent with preparing, discussing and implementing a water treatment plan that was accepted by all state and federal agencies and adhered to strict environmental regulations. Grain hopper barges were rented to control and treat the water that was used in the drilling operations. Another challenge crews ran into was the discovery of caverns when drilling into some parts of the bedrock. Michels worked with the engineer to develop a plan to construct the drilled shafts that encountered the caverns.

Jan 1, 2019

By Michael Perlow

Helical screw piles in use since 1838 are routinely used for energy, transportation, municipal, industrial, marine and coastal infrastructure as well as for excavation support, environmental remediation, and foundation repair. They are especially well suited for work in constrained areas, renovations and structure retrofits. Helical pile design procedures over the past 10 years have gone through a remarkable evolution with the establishment of the 2007 AC358 Helical Pile Acceptance Criteria and inclusion of helical screw piles in the 2009 International Building Code (IBC). New 2009 IBC building code requirements and AC358 Acceptance Criteria are presented along with advances in helical pile design procedures, installation, QA/QC, and recommended load test verification criteria. Use of helical smart piles to validate helical pile design and verification of ultimate pile capacity is highlighted.

Jan 1, 2011

By Clif Kettle

The paper will detail the design and execution of passive and active settlement control measures, the means adopted to overcome the various physical and operational constraints, and to meet specified allowable settlement criteria. The paper will highlight the close integration between the tunnelling and geotechnical contractors, designer, and Client, and demonstrate how particular practical difficulties were overcome by both the design and the construction methods.

Jan 1, 2008

By Prakash Annamalai Rangasamy, Muthukkumaran Kasinathan

"Infrastructure development like elevated expressways, metro train and flyover are required proper foundation system to carry heavy traffic loads/significant lateral load, especially in the presence of hard stratum at shallow depth. Pile foundation under bridge pier system is widely adopted in metro projects where the piles are essentially socketed in rock. However, the drilling in hard rock is a time consuming process and needs heavy machineries which lead to delay in construction activities. In the present study, the influence of free standing height on rock socketing under lateral load is investigated. The experiments were conducted on an instrumented model pile with varying depth of socketing and for varying Lf/D ratios. The experimental results shows the load carrying capacity of the pile increases by increase in Lf/D ratio, where in the case pile without socketing (bearing on rock) is compared with 3D depth of socketing. Thus socketing the pile provides significant benefits on carrying capacity of lateral loads. Embedding the pile into hard strata reduces the lateral displacements substantially compared with pile bearing over hard strata. Form the study, it is noticed that the influence of rock socketing has significant effect in the lateral load capacity. And also, the effect of free sanding height play a major role in the lateral load capacity of the rock socketed piles.1. INTRODUCTIONA substructure carrying heavy lateral load at shallow depth, the structure has to be socketed into hard strata to enhance the efficiency of load carrying capacity. The existing field practice is to socket the end bearing piles in hard strata over a minimum depth of four times the diameter of the pile based on rock classification (IS 14593:1998). Reese (1997) developed p-y curves for analysing drilled shafts in rock under lateral loading, based on strong and weak rock criteria. The proposed p-y curve approach has the ability to simulate the nonlinearity and non-homogeneity of the rock mass surrounding the drilled shaft. Gabr et al. (2002) proposed a hyperbolic p-y criterion based on field tests on small diameter drilled socketed shafts. By considering pile as linearly elastic semi-infinite space and soil as homogeneous isotropic material, Poulos (1971) proposed solution to determine the horizontal displacement and pile head rotation. Poulos (1972) extended this elastic continuum approach to give an approximate solution by considering drilled shaft and pile bearing on rock as fixed and pinned end boundary condition. Zhang et al. (2000) developed a non-linear continuum approach for drilled shafts in a soil and rock mass by considering the effect of soil and/or rock mass yielding on the behaviour of shafts. Randolph (1981) conducted a parametric study on the response of laterally loaded piles embedded in an elastic soil continuum. The study was conducted using the finite element method and the results were fitted with closed-form expressions from which the lateral responses of piles were calculated. The solutions given by Randolph (1981) were expanded by Carter and Kulhawy (1992) from the results of finite element studies on the behaviour of laterally loaded flexible and rigid drilled shafts in rock. Desai and Christian (1977) gave a finite difference program to solve rock socketed problems by considering soil and rock mass as elastic-perfectly plastic. Zhang et al. (2000) verified the proposed finite difference method with existing field test results. Gabr et al. (2002) and Liang and Yang (2006) proposed hyperbolic p-y curves based on filed test results and verified with finite element programs. However the need of field and lab scale experimental studies to validate the existing methods of analysis is necessary."

Jan 1, 2015

By Jesús E. Gómez

A total of 260 micropiles were installed as part of a retrofit effort for two existing bridges. The micropiles consisted of hollow core bars installed under limited headroom conditions. Of the total number of micropiles, 180 were installed in submerged sand and 80 were installed in stiff, silty clay. The micropiles were drilled using a lean cement grout which was re-circulated for de-sanding and re-use. Final grout was injected upon completion of drilling to the design tip elevation. The micropiles were subject to a rigorous quality control that included grout quality testing and proof-testing of each production micropile. This paper presents a description of the procedure for installation and quality control of the micropiles. The successful proof-testing of all the production micropiles showed that hollow core bar micropiles can be used effectively in granular and fine-grained soils. Hollow core bar micropiles offer particular advantages when installed in submerged sand formations with respect to other traditional micropile types. The results of the proof load tests are presented in a companion paper.

Jan 1, 2007

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Karsten Beekhaus, Sander W. Odijk, Rabea Bahlum, Mazin Adnan, Ayman Abdelh Al Nuaimat, Hassan Farhat

The Arab Potash Company, APC, is one of the 10 largest potash producers of the world. The solar ponds at the Dead Sea, used for the enrichment of the salt content in the brine, are of crucial importance for the first step in the exploitation of the potassium salt. Targeting at the expansion of production in the since over 50 years utilized facilities, the increase of the brine exploitation capacity, reducing the substantial brine seepage losses from the ponds, becomes a crucially required measure. In this context, the remediation measures on the over 11 km long Dyke 1, being a main dyke of the solar ponds system, became inevitable to reduce the brine losses, prevent further development of sinkholes and cavities and hence assuring the stability of the dyke. The highly aggressive environment, the acting hydraulic conditions and the sensitive stratification and nature of the existing ground represented remarkable challenges for the design, as well as its implementation by the construction activities. Royal Haskoning developed a solution addressing the challenges above and targeting at a high sustainability of the executed structure, especially in view of the various geological and hydrological hazards repeatedly occurring in this Dead Sea region, including sinkholes of several meters by diameter and depth. The construction works, consisting of a cut-off wall, with depths reaching down to 31 m, were awarded to Bauer International FZE, a subsidiary of Bauer Spezialtiefbau GmbH. Upon the execution of the first section of 4.2 km length, additional sections were subsequently commissioned, also on further dykes, totaling to about 300,000 m² of cut-off wall. The specific project conditions, such as utilization of cutter technique for the excavation in Halite rock, the stability of open trench exposed to hydrostatic pressure of salt-saturated ground water, resulted in unconventional requirements towards the supporting fluid. The extremely aggressive saline conditions –with a Dead Sea water density of 1.25 tons/m3; one of the world's saltiest water–, were further a decisive factor for the definition of the backfill material concept. Despite its clear advantage for construction of cut-off walls with installed sheet piles, the single-phase system with hardening slurries, fulfilling both functions of excavation support and cut-off wall backfill material, had to be abandoned in favor of the two-phase system, to construct a hybrid cut-off wall made of sheet piles and plastic concrete.

May 1, 2022

By Pierre Gouvin

"This paper discusses real time monitoring of utility vaults during the reconstruction of the Elliot Bay Seawall in Seattle. The project, undertaken because deterioration of the old wall posed increasing risks to property and lives, impacts businesses, ferry terminals, a rail line, and electrical utilities that distribute power to much of the downtown area. The project, which has been fast tracked to minimize risk and commercial impacts, involves multiple contractors with heavy machinery working in an area one mile long and only a few hundred feet wide. This presented challenges to monitoring of the utilities, as will be discussed in the paper.INTRODUCTIONThe Elliot Bay Seawall (EBSW) was built in over a period of 18 years, starting in 1916. It consisted of a vertical concrete wall placed on a timber pilings and timber relieving platform. The seawall also retained fill that served as the foundation for a road known as the Alaskan Way. The seawall has performed well over the years, but now cracks in the concrete have allowed loss of fill, and the timber piles and support structures have been weakened by marine boring insects.The project to replace the seawall was undertaken because deterioration of the old wall posed increasing risks to property and lives. Because the project impacts businesses, tourism, ferry terminals, and a rail line, it was given a compressed timeline - 36 months from start to finish. In addition, construction activities have been staged carefully to minimize disruption of Salmon and other wildlife living in Puget Sound. In fact, will incorporate several habitat improvements to promote sea life, such as a nature-imitating textures in the surface of the wall and a glass deck structure that allows sunlight to reach the water. (Fig. 1) shows a schematic of the planned new wall.The sheet piling, concrete piles, jet grouting, drilled shafts, ground freezing, and demolition activities are all taking place in the narrow corridor that holds the subsurface ducts and vaults protecting Seattle’s electrical power distribution. If the network of duct bank and vaults were to experience differential settlement during work here, then most of downtown Seattle would be in the dark. Thus it was important to provide real-time displacement monitoring of these utility structures."

Jan 1, 2017

By George Piscsalko

"Quality control of drilled shafts and ACIP piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult to properly inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. In other cases, such as ACIP piles, it is impossible to inspect the shaft in any manner prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity in drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity over 100% of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube typically 12 to 48 hours after concrete placement, or from embedding thermal wires within the shaft prior to concrete placement and monitoring them with unattended data collectors for 12 to 48 hours after concrete placement. This Thermal Integrity Profile method will be described in detail and several case histories will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing, and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.IntroductionDrilled shafts and Augered Cast-in-Place (ACIP) piles have been increasingly used over the past several years due to several reasons including the reduced noise and vibration, speed of installation for ACIP piles, and the large axial and lateral capacities which are attainable for very large drilled shafts. ACIP piles are drilled and cast without any visual inspection. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2017

Volume 1 pages 665-671 Title should read as Dynamic pile testing of H-piles at HDB sites J.Wei, Y. S. Heng, C. S. Lok, M. K.Chong Housing and Development Board, Singapore 'tons' should read as 'tonnes' Para 3.2 fourth equation (page 667) [TC = t2 v.dt t = 0 should read as TC = t2 v.dt - s t = 0]

Jan 1, 1994

By Dinesh Hinduja, Pérez: Miguel

"Large structures are generally exposed to dynamic and structural loading. They require usually either foundation connected to hard rock through sockets or driven foundations, which encounter boulders as well.In this regards drilling hard-rock sockets or boulder offshore or onshore can be a challenging job especially when deep foundations are mandatory. To overcome the challenge, specialized equipment like a Pile Top Drilling rig (PBAs) can be used, which have to be correctly set-up and operated in order to get its maximum drilling performance. High performance drilling with PBAs requires maximizing key elements of its operation. The configuration and management of the drill string components are important. The key elements are constant weight on bit which is done by adjusting ballast and managing thrust force; and selection of cutters and proper flowing discharge.The methodology is based on the experience from over 40 years of building and operating PBAs for different project applications. These applications include drilling offshore and onshore for:?Superstructures and buildings?Drilling platforms, barges and jack-ups?Harbours, jetties, dry docks and dolphins?Bridges, piers and causeways?Marine sewerage diffusers?Offshore wind farms?Dam rehabilitationMHWirth documented methodologies demonstrate that by using PBAs properly it is possible to improves performance of underwater drilling for hard-rock sockets and boulders which ultimately reduces project-cost.Background. There is a significant percentage of total project cost in structural foundations. Equipment capabilities and technics to drill shaft with rock-sockets and embedded boulders onshore and offshore are highly developed due to the dramatic equipment advancement and experience in the last 40 years. Formerly, driven piles accounted for the majority of foundations either onshore or offshore, following the experience of previous practice in the market. Nowadays, deep drilled foundations can be constructed to carry the load through the overburden down to the sound load carrying rock or soil.Scope and objectives. The overall objectives of this study are:?Synthesis information on current practices to drill shaft with rock-socket and/or embedded boulders onshore and offshore with Pile Top Drill Rigs?Identify the principal challenges evolving with practice?Provide suggestions for improvements in the construction of drilled shafts through proper operation of Pile Top Drill Rigs?Convey information through case studies and experiences"

Jan 1, 2015

By Ashley Shirer

Have you heard a geotechnical engineer rail against using the word "dirt"? The typical maxim is: "It's not dirt, it's soil!" This axiom is so prevalent that it is joked about on the construction site. How did we get to the point in our profession that soil is too technical to understand, while dirt is not viewed as important? Take a moment and think about the images that come to mind by the word soil. Responses range from the sand at a playground to the mud that sticks to the bottom of your shoe, the dark loam found in gardens to the firm earth under your feet. But do you know where the term soil originated? Or how it was intended to be used? This article looks at how word choice can lead to very different motivations for owners, designers and constructors.

May 1, 2023

By Sebastian Lobo-Guerrero

Welcome to DFI45! our first on-line annual meeting. We cannot deny the severe impacts that the COVID19 pandemic is having in our industry and our lives. We extend our support to all of our members that have been impacted in many different ways. But through the middle of this difficult and challenging times, our beloved annual conference emerges, trying to re-unite our industry and remind us why we love what we do so much. DFI45 was not originally planned to be delivered virtually, but as our world changed, we adapted. Adversity became an opportunity to re-invent our annual conference. Thanks to the vision of our Organizing Committee, we saw the amazing new possibilities and DFI45 is today a reality. Our theme for this year is People + Purpose + Passion. This theme was decided before the COVID 19 pandemic started, but today it is more relevant than ever before. We are a group of very diverse people at DFI. Our organization includes Contractors, Consultants, Suppliers, and Academics just to name a few sub-groups. But we all have a common purpose and try to find common ground. We are all extremely passionate about what we do, and this excitement is really what makes this organization what it is today. This conference celebrates this passion as you can see in our three main Keynote Sessions. On a local scale, we want to go back and remember the contribution of our industry to our beloved National Monuments in Washington D.C. On a national scale, we want to explore and recap the development of Government Guidelines and Specifications that became the world standards. And finally, we want to close the conference with a session celebrating the family legacy and share amazing stories of families with multiple generations working in our industry. Besides our Keynote Lectures, the conference is full of exciting content such as several case histories, experimental research in deep foundations, applications of new technologies, business aspects and risk management considerations for deep foundations, just to list a few. We also have our now traditional events such as the Hal Hunt Lecture, Awards Reception, DFI Educational Trust 5K Fundraiser, etc. For the first time, all this content will be delivered using different virtual formats, including on-demand presentations, plenary sessions, interactive chat rooms, etc. We are excited about these possibilities. To conclude, we need to recognize the people that against all odds made this conference a reality. First our sponsors, they adapted to the most abrupt change never thought before, and they always stayed there with us, providing unconditional support. Without them no conference is possible. Next, our Organizing Committee that re-invented the concept of an annual conference and found new and exciting ways to make this happen! Our Technical Program Committee led by our Technical Program Chairs, Jennifer Nicks and Gregg Piazza, showed us that nothing is impossible. And last, but not least, the amazing DFI staff that make dreams reality. It has been an honor to serve as the Conference Chair for DFI45. It is an experience that will stay with me for the rest of my career. Conference Chair: Sebastian Lobo Guerrero, Ph.D., P.E. American Geotechnical and Environmental Services (A.G.E.S.)

Oct 27, 2020

By Y. Z. Wang

Zhengzhou Yellow River Highway Bridge, which is under construction, has a total length of 5550 meters with bored cast-in-place concrete piles as the foundations of its piers which have a diameter of 2.20 m with a length of approximately 65 m. This paper attempts, through the introduction of the said bridge's footing pile design and construction, mainly to give an account of the following points: 1) experiment and research on deep friction pile with a large diameter, 2) calculation of vertical carrying capacity of the pile with a large diameter, 3) analy­sis of horizontal forces the footing-piles of the column-shaped piers, 4) application of normal and reverse-circulation rotary drilling technologies to the construction of bored cast-in-place concrete piles with a large diameter and 5) applying super-sonic impulse on destruction detective device to examine the quality of the pile concrete.

Jan 1, 2010

By Farhad Elmi

In this paper, a new procedure is used to find the bearing capacity of single piles and cone penetration resistance in soils. Although the procedure is mainly applicable to clay and sand using any plasticity model, this paper deals only with steady penetration in Sand. Cylindrical cavity expansion around the probe in a calibration chamber is modeled by finite element method using the HUJEUX elasto-plastic multi-mechanism model. The penetration resistance (qc) is related to cylindrical cavity expansion pressure limit (pL) using the method of Salgado et al. (1997). This procedure is tested using the results found in 3S/IMG calibration chamber. In this article the word "penetrometer" refers to both pile and cone.

Jan 1, 2002