Search Documents

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more diffi cult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizing tie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State. INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges. Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story offi ce building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall."

Jan 1, 2007

By Lisheng Shao

Soil mixing and jet grouting have been widely used to support heavy structures such as tanks, cement silos, and storage buildings. Although the installation methods vary between soil mixing and jet grouting, the end product of soil-cement columns behaves similarly in supporting structure loads. In many cases, soil-cement mass treatment offers the owner savings over driven/drilled piles. This paper discusses the design methodology, production work, and quality control, with supporting figures, of a recent large complex tank farm project. The project consisted of constructing six above-ground steel storage tanks and an approximately 700-foot-long fill slope. The tank farm site is located in an industrial area of southern California, with highly variable subsurface conditions consisting of compressible soils and buried construction debris. The compressible soils necessitated that the new tanks be supported on deep foundations. A test pile program performed previously at the site showed that conventional driven concrete piles were not feasible because of buried construction debris, therefore a soilcrete system was proposed. Site design included evaluating the total and differential settlement and column group bearing capacity under both static and seismic loads. Extensive field and laboratory testing confirmed the design soil-cement strength and modulus of both the soil mixed and jet grouted soil-cement columns. The project operation and quality control programs are also included in this paper.

Jan 1, 2010

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

New York City is an urban environment with a history spanning over 200 years. The coastline of New York has changed over the years. In the East River, old bulkhead and remnant of relieving platforms together with variable bedrock elevations pose challenges in the design and construction of deep foundations. This paper presents a Case History of high capacity deep foundations along the Franklin D. Roosevelt (FDR) Drive on the Upper East Side in New York City. The project consists of a ramp that overpasses the FDR Drive allowing heavy trucks to access the Marine Transfer Station (MTS) facility built over the East River. Large diameter drilled shafts and mini-piles socketed to bedrock were designed and constructed. Remnant of old bulkhead was encountered at the site and a Ground Penetrating Radar (GPR) investigation was completed during the subsurface investigation phase of the design. This paper discusses details of the subsurface investigation program and design methodology of the high capacity drilled shafts and mini-piles. It also describes construction methods and results of Osterberg Load tests documenting the field values of skin friction through the rock socket. Other construction challenges include construction and drilling rock sockets for drilled shafts over sloping bedrock. 1. INTRODUCTION New York City is a renowned urban city that always calls for the most delicate, yet complex, and robust superstructures and most importantly substructure designs. The historic preservation of this large 200 years old city of 319 square miles is ever changing. Shorelines are often extended to accommodate new infrastructure and very often many miscellaneous structures are discovered below the ground surface. The East 91st Street Ramp was constructed to provide access to the East 91st Street Marine Transfer Station over FDR Drive and York Avenue. Another alternative ramp will be relocated to the South Bound (SD) of the FDR Drive at 92nd Street. A subsurface exploration program was completed in accordance with the New York City Department of Design and Construction (NYCDDC) general requirements, Section 4.5, to perform subsurface investigation along the FDR Drive in Manhattan, New York.

Jan 1, 2019

By Andrew Middleton, Mark Wyatt

"The Brickworks Marketplace Project is a significant shopping centre development in inner north west Adelaide constructed by Badge Constructions in 2014 and 2015. The site was a former brickworks with a deep pit containing various extents of uncontrolled fill which was to remain on site, and with a remaining void up to 6 m in depth. The existing uncontrolled fill was improved using the High Energy Impact Compaction system, and the pit backfilled using a quarry crusher byproduct selected by trial and a recycled crushed concrete and bricks and compacted in deep lifts. This approach resulted in significant savings in compaction time, cost and building foundations. The settlements of various parts of the completed works have been monitored since February 2015 and this monitoring has demonstrated small settlements which meet the user’s constraints.INTRODUCTIONThe Torrensville Brickwork Markets project involved the transformation of a former brickworks and clay pit site into a regional 17,000m2 shopping centre, opening in June 2015.The site was a former brickworks with adjoining clay borrow pit. The clay pit had been partially backfilled over many years with ‘uncontrolled’ fill comprising ‘clean’ soil, bricks and kiln dust typically of the following thicknesses:??of the order of up to 7 m to 10 m but locally up to 15 m in the western part of the site??2 m to 5 m in the south-eastern part of the site; and??less than 0.5 m in the north-eastern part of the siteAnecdotal reports suggested compaction of some of the fill may have been undertaken, although this not able to be confirmed nor records obtained.Initially it was proposed to take up the existing uncontrolled fill, sort and recompact or remove to landfill, followed by backfilling in conventional means over 500,000 cubic metres of imported filling to a thickness of up to approximately 6m to backfill the former pit. This work represented a significant cost and was not economically viable.During early negotiations, the contractor proposed an alternative to retain and ground improve the existing filling on site, and to backfill the pit with fill placed and compacted in deep lifts, thereby significantly improving the economics, environmental and community impacts of the proposed works.The developer agreed to the proposal with the following performance criteria:??a settlement of =10 mm after 10 passes by the Impact Compactor (on existing subgrade areas);??a bearing capacity of 250 kPa for high level footings;??a maximum long term differential settlement of 40 mm (measured over 16 m), ie. 1 in 400; and??a minimum modulus of 40MPa."

Jan 1, 1900

By Benjamin Jennings, Jason Herron

In the summer of 2016 Xcel Energy experienced a storm event that resulted in the collapse of approximately 8.5 miles of a 345 KV transmission line near Rogers, Minnesota. In design of the new transmission line, Xcel Energy determined that ten tower locations would be replaced with steel H-frame structures supported by helical piles instead of wood H-frame structures supported by driven wooden piles. A steel foundation was proposed for the towers due to time constraints and site conditions unfavorable to large pile driving equipment. Xcel Energy contacted the helical pile manufacturer Hubbell Power Systems, Inc. (HPS) for aid in the design of a complete steel foundation for the structure legs. With the shear, moment, and axial loads provided, the manufacturer used pile group modeling and axial capacity software to design a four helical pile group; and used 3D modeling and finite element software to design a moment resistant grillage to connect to the tower base. The steel grillage utilizes a new moment resistant connection and clamp system to transfer loads from the piles to the grillage. This connection provides a true fixed head condition and reduces lateral deflection issues typical to smaller diameter piles in pinned head connections. The clamp is designed to deform the helical pipe pile shaft and transfer the full axial load of the structure through the mechanical and friction connection. The helical piles and the moment resistant grillage were manufactured with shorter than average lead times and a helical pile installation contractor performed the installation. An expedient plan of install was developed by the contractor that resulted in an average installation rate of one complete set of tower foundations per day. The design of the moment resistant grillage, clamping system, and excellent foundation construction by the contractor provided an expedient and efficient foundation system to be discussed in this paper.

Jan 1, 2017

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The stadium development consists of construction of a 68,500-seat, open-air NFL football stadium for the San Francisco 49ers. The main structure will consist of a 7-story above grade steel structure supported by over 3,000 piles. Berkel and Company Contractors, Inc. (Berkel) was selected as the design-build pile contractor who used their auger pressure grouted displacement (APGD) piles for this project. During an indicator pile installation and pile load test program, fifteen piles were tested to develop installation criteria to support demands of 150kips tension and 180 kips compression. Following the indicator pile program Berkel installed 3088 piles in 30 working days. Throughout pile installation data were collected with an automated data acquisition system (DAS). During pile installation field engineers from Treadwell & Rollo observed the pile installation as well as the real-time data from the DAS. Strategic staging and pre-production planning by Berkel along with consistent collaboration with the design team created an atmosphere for a successful and on schedule project completion.IntroductionThe new San Francisco 49ers Stadium in Santa Clara, California will be a 68,500-seat facility, a rendering of which is shown in Figure 1. The main structure will consist of a 7-story above grade steel structure supported by more than 3,000 piles. The north, east and south portions of the stadium are designed as an open seating bowl, while the western portion includes open seating at the lower levels and seven-story tower which houses over 150 suites.The stadium project includes the stadium structure, as well as elevated open pedestrian walkways, commercial community space, and three new pedestrian bridges spanning a nearby by creek. Sustainable designs and innovations such as a green roof, photovoltaic panels, a ground source geothermal system, stadium-wide Wi-Fi capability, and access to public transit are provided throughout the project. The stadium is designed as an open, light, and airy structure and is surrounded by an existing amusement park, office buildings, the Santa Clara Convention Center, and the training facility of the 49ers."

Jan 1, 2015

By Thang V. Nguyen, Lisheng Shao, Gary E. Taylor

"The Community Memorial Hospital of Ventura, California, proposed to build a new state-of-the-art Cancer Treatment Center with radiation shielding walls and roof. The loose silty soils at the site had the potential to liquefy during an earthquake, which would result in significant settlement under the heavy footing loads. Treatment options included various deep foundation alternatives, as well as several ground improvement methods. The choice of wet soil mixing minimized the disturbance to the adjacent hospital during construction and potential settlement. Wet soil mixing allowed the structure to be supported on a raft foundation, meeting the stringent building total and differential settlement criteria. The authors also performed unit cell 3-D finite element analyses to evaluate the behavior of the wet soil mixing system in seismic loading conditions. This paper highlights the ground improvement design, construction, QA/QC, and the research related to evaluating the effectiveness of soil mixing for liquefaction mitigation.INTRODUCTIONThe Ventura Community Memorial Hospital proposed the construction of a new Cancer Treatment Center to replace the existing structure, which was built in 1901. The hospital complex is located in a wellestablished residential neighborhood. The soil conditions at the site of the proposed structure required ground modification to support the very heavy radiation treatment section of the building and limit settlement. Originally, 90-foot-long precast piles were considered for foundation support. Based on supplemental Cone Penetration Tests (CPTs) performed, the deepest CPT did not encounter competent pile bearing strata at a depth exceeding 30.5 m (100 ft). This could result in failure of the piles under long-term conditions, especially if hydro-consolidation occurs. The more realistic pile penetration depth would have been 36.6 to 45.7 m (120 to 150 ft). In addition, the excessive noise in association with pile driving would have been unacceptable to the community, patients, and staff of the hospital, so an alternative ground improvement solution was required.The specialty geotechnical contractor recommended wet soil mixing, an economical solution of creating a soil-cement product known as soilcrete that would significantly reduce the construction related noise and provide a more complete deep foundation for the structure.SOIL CONDITIONS AND SETTLEMENT CONCERNSThe subsurface soils were interbedded (Fig. 1) consisting of loose to medium dense silty sands, and soft to medium stiff silty clays to a depth of 30.5 m (100 ft). Groundwater was encountered at depths of 9.1 m (30 ft) and historical high groundwater was at 8.5 m (28 ft) below the ground surface."

Jan 1, 2015

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

Rammed stone columns and similar reinforcement systems are used worldwide more frequently as a cost-effective method for improvement of foundations on soft soils. The effectiveness of the treatment method is evidenced by the increase in bearing capacity and reduction of compressibility of the treated ground. In this study, two job sites with over 500 stone columns were studied. On both jobs sites, shallow soft silty soils were found and stone columns were designed to support the foundations of MSE walls, which serve as abutments for viaducts. In order to verify the soil improvement efficiency CPT tests were performed before and after the construction of stone columns, also plate load tests were performed on both job sites to verify the deformation modulus of the stone columns. From CPT data it was observed an increase up to 30% of sleeve friction and 20% of tip resistance, which demonstrated a higher deformation modulus maintaining the same strength in the soil after stone columns construction. The plate load tests yield load-deformation curves which indicated that the original assumed modulus was conservative. As a result of these findings, optimization of the settlement reduction ratios was conducted using the modified values of deformation modulus for the soil and stone column, obtaining a reduction up to 30% of stone columns for further job sites with similar soil conditions.

Sep 8, 2021

By Sumantra Sengupta

"Northeast Frontier Railway (NF Railway) intends to connect Imphal, the capital of Manipur (bordering Myanmar) with Assam by railway link. They have planned a 125km long railway line that passes through steep rolling hills of Patkai region, eastern trail of Himalaya, and as a result large number of tunnels and bridges need to be designed. While the high mountains are penetrated by tunnel, the deep gorges between the mountain ridges are connected by tall bridges. The tallest of such bridges connects a gorge at about 140m above its bed level with an overall length about 700m at rail level. In all, five such bridges with tall piers are now under construction. With extensive study on possible alternate arrangement of the bridges considering the effect of high seismicity of the area, moderately to highly weathered siltstone/ sandstone as ground bed material, slope of the hills etc it was decided that bridge will be founded on 1.5m diameter bored cast in situ piles with length varying from 20m to 30m depending on the location. The substructures are RCC hollow pier and superstructures are steel open web through type girder of 103.5m span. Considering absence of any major construction work in the vicinity, it was decided that prior to design work, Site-specific spectrum study will be carried out and design will be carried out considering the varying stiffness of the tall piers, each of different height. Interesting results were obtained regarding behavior of piles under lateral loads generated by high seismic conditions. The paper discusses in detail the design of Pile foundations and the effect of bed material along the steep slope on which the piles are being constructed.INTRODUCTIONIndian Railway has undertaken the construction work of connecting the North-Eastern states of India through railway line. The major stretches of the area passes through hilly terrain and as a result the line passes through tunnels and bridges in succession. The tall mountains are being penetrated with tunnels and immediate after deep gorges are crossed with high level bridges. The entire area is under high seismically active zone. The bed material below the ground level of the sloped hill is 4 to 10 meter of mixed soil of sand, gravel, pebbles etc underlain by moderately to highly weathered sandstone, siltstone at the higher level and moderately weathered sandstone, siltstone at lower level. Considering all the aspects like constructability, maintainability, geological and geotechnical aspect, seismicity, stability, safety, functional aspect and cost it was finally decided that the bridges will be simply supported structure with open web through type steel superstructure of maximum span 103.5m and hollow cylindrical discretely varying RCC substructure with 1.5m diameter group of piles as foundation. The paper discusses on the design aspect of the pile foundation in the rocky strata in the hill slope. The codes and standards that have been followed for design are IRS (Indian Railway Standard), IS (Indian Standard), IRC (Indian Road Congress), AREMA (American Railway Engineering and Maintenance-of-way Association), UIC (International Union of Railway) provisions."

Jan 1, 2015

By Anupam Saxena

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading test, and installation of piles for a 22-story condominium tower in southwest Florida, U.S.A. ASC was commissioned to provide value engineering services in the proper selection of an economical and satisfactory foundation system. For the site-specific subsoil conditions, various types of foundations were considered and following an evaluation of high structural loads, site-specific constraints, and the production timeframe mandated by the project owner, a prestressed concrete pile-supported system was selected as an economical and effective foundation approach. The building foundations were designed for a compression capacity of 575 kN (65 tons) for the tower and 220 kN (25 tons) for the parking structure. The axial pile capacity and lengths were predicted using SPT91 software. The validation of these capacities was derived from driving 21 probe piles and performing static loading tests on selected probe piles (2 in compression and 1 in tension). The predicted pile capacities were evaluated with results from static loading tests on selected probe piles. This information was effectively utilized as part of an overall quality control program to install a total of over 920 prestressed concrete piles to lengths ranging from 11.5 to 16.5 m (37 to 54 ft) below existing ground elevation as part of the foundation support system.

Jan 1, 1996

By Nagarajan. D, Raja Rajan. K, Vijayakumar. T

Major bridges crossing mighty rivers must be constructed in flowing water. Constructing the sub-structure in water has been a challenging job for contractor. Special construction techniques with marine fleets to be adopted for waterfront construction. Enabling works like temporary piling platform and cofferdam used for pile and pile cap construction. Apart from this, enabling works like load out jetty to transport the materials from land to water; temporary walkway for access of workman to work location; temporary access bridge for construction vehicles movement; temporary liners for tower crane foundation; Concrete block to act as dead man anchor for barge movements were all required by the contractor for smooth functioning of site as per construction schedule. Investment in enabling works by contractor plays a significant role on profit margin of the project and of course with utmost safety. Design of enabling works for waterfront structures involves hydrological data like afflux, bathymetry survey, current force, scour depth and wave force to be taken cautiously for safe and economic design. Type of foundation and pile/well cap top level corresponding to water levels shall influence the construction scheme. Usage of geotechnical software like Wallap and Plaxis required for enabling work design to enhance the safety of the structure. Bathymetry and soil condition play a critical role in design and construction of enabling works. Water Discharge quantity in river along with water levels like low water level, high flood level, seasonal fluctuation of water levels has a great impact on design of enabling works. Establishing enabling works for waterfront construction near to an existing bridge is an additional challenge for the contractor. Along with design, constructing the enabling works in water requires special construction methodology and sequence of work. This paper shall provide insights on overview of design and construction of enabling works for waterfront construction.

Nov 1, 2022

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

The Waterman Hospital in Tavares, Florida was undergoing an expansion and required a below-grade excavation immediately adjacent to the Emergency Department. This wing of the hospital was under high traffic and required uninterrupted access for ambulances as well as helicopter landings. The below-grade expansion was also next to a part of the hospital which did not have a basement. Tiedback soldier beams and wood lagging were used as the earth retention system where the shoring line was not immediately adjacent to the existing structure. Structural jet grout underpinning was used to support the existing building and to serve as the earth retention system in the more sensitive area. Jet grout underpinning was chosen to minimize movements, loss of ground and settlement of the structure which was bearing on clean sand deposits. This paper will discuss the design, quality control and construction of jet grouting and its application to this project. INTRODUCTION Project Background The expansion of the Waterman Hospital included an addition to the Emergency Department. This addition was located adjacent to the existing hospital building in a congested area with limited access. The north side of the addition was bordered by the ambulance drop-off area. The south side of the addition was bordered by the helipad landing area. Both areas had to remain open and fully accessible 24 hours a day, 7 days a week.

Jan 1, 2019

By Harald Vogel, Johannes Lachenski, Friedemann Koetzel, Sebastian Schnell

In this paper, a digital subsoil approach, a work-in-progress, will be presented describing the transformation from a classical 2D to digital 3D thinking process in the design of geotechnical structures. Certain pitfalls as well as lessons learned are described, and the reader can understand that the digitalization process of the design of geotechnical structures is always a problem-focused approach by creating systems for certain processes rather than setting rules or regulations. Three project examples are presented. Two of the presented project examples feature a heterogeneous geology distribution and made it necessary for the design of the foundations to work with 3D subsoil and 3D calculation models. However, the digital 3D design process in the third project, an inner-city excavation pit, is driven by the complicated boundary conditions making it necessary to work in a parametric 3D design space. All projects have in common, that new processes had to be developed. The paper concludes with a flow chart describing the process of the elaborated digital subsoil approach.

May 1, 2022

By S. Chilka, I. Maloney, J. Brady

"The purpose of this project was to design the Electrical Service Platform (ESP) for the Cape Wind Offshore Wind Farm. The ESP structure comprises two primary parts: the topside platform housing the electrical equipment and the two jacket substructures providing foundation support to the platform. The topside is supported only by the two inner legs of each jacket. The site water depth is relatively shallow and the seabed comprised of loose sediment subject to severe local scour up to 18 feet. The piles are designed for local scour, storm conditions, vessel impact, ice loads and pile installation fatigue. This paper focuses on the design and construction aspect of this project.PROJECT DESCRIPTIONBackgroundThe Cape Wind project will be located in Nantucket Sound between Cape Cod on the Massachusetts mainland (northeastern coast of the USA) and the Islands of Martha’s Vineyard and Nantucket (Fig. 1). The project is to be sited on Horseshoe Shoal, about equal distances from the mainland and the two islands. The project will produce 75% of the electricity used on Cape Cod and the Islands of Martha’s Vineyard and Nantucket with zero pollution emissions and resulting in the reduced operations, fuel consumption and pollution emissions from the fossil fuel power plants in the region. The wind farm, if constructed per plan, is expected to be America’s first offshore wind farm.The wind farm will consist of an array of 130 Siemens 3.6-megawatt offshore wind turbines with a combined production capacity of 468-megawatts. The offshore wind turbine towers will be bolted onto the transition pieces supported by monopile foundations driven into seabed. The power from the 130 wind turbine generators will be delivered to the Electrical Service Platform (ESP) by an array of up to 14 seabed conductors."

Jan 1, 2017

By Ganesh Deepak K., Anjana R. K., Dr. Kumar Pitchumani N., Rajasekharam R. M. V. M. S. S.

The Phase 2 of Chennai Metro is being introduced in the city to ease the dependence on the existing transportation systems. Phase 2 is a combination of underground and elevated metro stretches comprising of three corridors. The current study focusses on the underground stretch of Corridor 3 which has a total of 29 underground stations. Construction of the underground cut and cover stations results in ground movements, which in turn impact the structures adjacent to the excavations. The greenfield ground settlement can be evaluated with the help of empirical approach or an approach requiring finite element modelling (FEM). The paper compares empirical and FEM approaches with regards to ground conditions in Chennai. Further, with the predicted ground settlements, building damage assessment is performed. The damage category of a building is defined based on the estimated tensile strains. This paper also compares the building damage assessment with empirical method and finite element modelling.

Nov 1, 2022

By Madhu. P, Srinivas. K

Measurement of thermal properties like thermal conductivity, thermal resistivity, heat capacity and thermal diffusivity for materials, it plays a crucial role in a wide range of various civil and electrical engineering projects, and many field applications like building’s basement, power generation, underneath soil heating, wastes from nuclear as well as thermal plants, and buried cables. Thermal conductivity of soil depends upon various geotechnical parameters such as type of soil, moisture content, particle size distribution, density, and compaction characteristics. Earlier studies, the measurement of thermal conductivity of soil by incorporating the heat source methods. Thereby expensive and time taken to conduct in laboratory as well as field measurements. The thermal conductivity is determined by fabricated probe and used in this work. Fabricated probe was calibrated with glycerin. The thermal conductivity of the soil increases as the water content and density increase because these factors are majorly influencing and water has a higher thermal conductivity than soil minerals, and grain to grain contact increases as density increases. therefore, Thermal conductivity is higher in coarser soils than in finer soils. The details regarding of this work as explained in this paper.

Sep 1, 2022

By Melissa S. Beauregard, Randall A. Pietersen

This study focuses on quantifying the effects of water infiltration on a full-scale energy pile system’s ability to meet the thermal demand of an HVAC system. Theoretically, an energy pile system should increase its thermal capacity after a rain event due to increased moisture content creating an increase in thermal conductivity of the surrounding soil matrix. The United States Air Force Academy has an energy pile research site consisting of 8 full-scale energy piles located below a shower facility. The local colluvium surrounding the piles allows for relatively high water infiltration during rain events. This study uses an 11kW Precision Geothermal Geocube to apply a thermal load on two single-loop piles. A weather station located south of the structure records atmospheric conditions. Results indicate that moderate rain events can caused up to a 23% increase in the system’s thermal exchange capacity. This change is due to the increase in moisture content near the surface, which penetrates to deeper soil layers with time. The time required for moisture to penetrate to greater depths and then dissipate in the soil matrix, explains why increased system performance is seen for over a week following the passing of a singular rain event. 1 INTRODUCTION With a “future-forward” focus, there is an ever-pressing economic and environmental need to use sustainable sources to meet growing energy needs. HVAC is typically responsible for 34% of the overall energy required by commercial buildings and 48% of the energy required by residential buildings (USEIA, 2009; USEIA, 2012). Energy piles are a low cost, sustainable technology that have been used to offset this energy demand incurred by a building’s space heating and air conditioning requirements. An energy pile consists of heat exchanging elements in a closed loop system integrated into a building foundation and connected to a ground source heat pump (GSHP). It is most common for these heat- exchanging elements to be constructed within a drilled shaft foundation due to both construction practices and geometric considerations. This system operates based on the principle that at a certain depth below ground (typically 4 meters) subterranean temperature remains constant at a value equal to the mean annual air temperature at a given location (Kavanaugh et al., 1997). This allows the soil to function as a heat sink for cooling operations and a heat source for heating operations when exchanged within this zone of relatively constant temperature. For the past 25 years, the implementation of energy pile technology in public, residential, and even large-scale architectural complexes has slowly expanded which has created an increase in research into the topic as a result (Brandl, 2006; Hamada, 2007; Sekine et al., 2007; Gao, 2008; Bourne-Webb, 2009; Stewart and McCartney, 2013; Murphy et al., 2014). When pile construction takes place beneath the groundwater table, soil is under fully saturated conditions, maximizing thermal exchange for a GSHP system. Under unsaturated conditions, however, changing moisture contents change thermal conductivity values in a soil, which affect a GSHP system’s ability to meet a thermal demand. The observational data presented in this paper apply to GSHP systems in unsaturated soil conditions.

Jan 1, 2019

By Robert L. Goehring, Fred Munene

This case history for three major additions to a tire manufacturing plant in north Georgia discusses the impact of highly variable Karst (sinkhole) geology on both foundation design and construction. For Phase 3, alternatives were considered for a heavily loaded mixing tower with up to 2,000 kip column loads. A non-traditional approach of using auger cast piles was adopted. To satisfy a risk-averse Owner, a pile load testing program including strain gauges was conducted. One test pile was cored full depth to demonstrate effective bearing on steeply inclined rock. For Phase 4, similar methodology was used at another critical mixing tower structure associated with that phase and the installation procedure was refined to reduce grout take. In Phase 5 construction, another mixing tower and the equipment pits were supported on auger cast piles. After pile installation, a sinkhole opened up between two equipment pits. Remedial grouting was performed. Development also required construction of a R&D building over a 96 inch diameter RCP storm sewer. Auger cast piles were used to support the building to avoid overstressing the existing pipe and risk separating joints. This case history outlines lessons learned while constructing auger cast piles in Karst and proving quality was built into the foundations.