Search Documents

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By R. I. Cavanagh, A J. Last

THE USE of higher grade charges in blast furnaces in the form of sintered or pelletized concentrates has been increasing rapidly. The question of beneficiation of iron ores for this purpose is therefore receiving much attention as more deposits are developed. Many iron ores may respond well to magnetic roasting procedures followed by magnetic concentration, however, in most cases other more standard ore dressing methods are competitive and cheaper. For magnetic roasting as applied to iron ore beneficiation, the present question is "Can it be economically justified in situations where it appears to produce good results?" The following collection of information on the general status and operations of magnetic roasting methods may be helpful in considering this question. Magnetic Roasting Magnetic roasting involves the transformation of non-magnetic iron oxides, hydrated oxides and carbonates by means of heat and suitable

Jan 1, 1961

By George P. Demopoulos, Yan Zeng, Zhibao Li

Precipitated silica is marketed with a rising demand as reinforcing filler in the rubber industry and as a potential raw material for the synthesis of lithium-ion battery electrodes. Due to an awareness of the environmental impact of the existing processes for the production of precipitated silica, a green and sustainable process was proposed by using sodium bicarbonate (NaHCO3) as an alternative to sulfuric or hydrochloric acid in the precipitation reaction with sodium silicates. The use of NaHCO3 allows for better control of the supersaturation and pH to form silica with desired quality. Additionally, Na2CO3 solution as the process by-product is recyclable because it could be recovered to produce NaHCO3 by absorbing CO2. The solubility of sodium metasilicate nonahydrate (Na2SiO3·9H2O) in the Na-CO3-HCO3-OH-H2O system was measured using a dynamic method in the temperature range from 288.15 to 308.15 K. It is found that the solubility of Na2SiO3·9H2O decreases with increasing concentration of either Na2CO3 or NaOH over the investigated concentration range. With the aid of the OLI platform, a chemical model for the Na2SiO3-Na-CO3-HCO3-OH system was established with newly obtained interaction parameters of the Bromley-Zemaitis model by regression of experimental solubility data. The new model predicted the solubility of Na2SiO3·9H2O in multi-component systems with good agreement and was used to conduct a preliminary feasibility study of the new process.

Jan 1, 2015

By W. A. Lang

"I.-IntroductionAn attempt bas been made in this paper to provide a basis for appraisal of the future of the coal briquetting industry in Alberta by outlining the processes used for briquetting various ranks of coal, by specifying the requirements of a briquetted fuel, by indicating .the status of the industry in the United States, by giving developments in Western Canada, by assessing costs of processing, and by discussing briquetting researches in progress. Much of .the detail bas been omitted since this might mask, rather than reveal, the more important phases of the problem. Reference will be made when possible to published articles where many of the details can be obtained.It should be stated at the outset that, in the writer’s opinion, there are three possible developments in Alberta as regards briquetting: (a) an expansion of the briquetting of the fines of • non-coking and coking coals of semi-anthracite, and of low and medium volatile bituminous rank; (b) the processing of the fines of high-volatile C bituminous coals; and (c) the upgrading of the lower rank high-moisture sub-bituminous coals. Details of the chemical and physical properties of these coals can be obtained in publications of the Research Council of Alberta (1, 2), and of the Fuel Research Station, Bureau of Mines, Ottawa (3).Semi-anthracite and low and medium volatile bituminons coals occur in the mountain areas of Alberta, where, during the upthrust of the Rocky mountains, the coal beds served as the sliding surface. This resulted in the coals being; crushed and consequently they contain a h1gh percentage of fines. In some cases they are high in mineral matter and require to be cleaned before being processed. However, the cleaning of fine coal is both difficult and costly. Both the amount of fines present in the mine-run coal and the amount of mineral matter associated with the coal have increased through the introduction of mechanized mining and through the recovery of coal by stripping operations."

Jan 1, 1950

By George W. Bain

Summary During the last three years the discovery of gold in the belt of volcanic and sedimentary rocks extending eastward from the Porcupine and Kirkland Lake gold-fields has caused a great deal of excitement in mining circles. The area is heavily drift covered, and every aid to the location of veins is eagerly grasped. A knowledge of the physiographic history of the area is of the utmost importance in the application of many of these aids. Evidence is presented to show that glacial erosion has lowered the general elevation very little below the pre-glacial level, and that many glacial erratics have been carried less than three miles southward. Probably a knowledge of the general geology of a: region was never more necessary to the understanding of the distribution and continuation in depth of the mineral veins than in this area. Four distinct granites occur in the region, and gold-bearing veins are genetically associated with only one of these. Two types of quartz-feldspar porphyries have been found, only one of which has any bearing on the locus of the mineral veins. Many other examples of this complexity of associations might be cited, but everyone goes to show that in most cases the economic importance of the deposits can be realized only after the regional geology is understood. A series of sandstone, limestone and shale intruded by granite lies unconformably below the Keewatin lavas. The latter are intruded by a gneissoid granite and are overlain unconformably by the thick series of Timiskaming greywackes and silts. These are intruded by carbonated syenites and syenite porphyries which have since been rendered somewhat schistose.

Jan 1, 1927

By R. F. Robertson

"Adsorption isotherms of hexyl mercaptan vapour on synthetic sphalerite, zinc sulphide and zinc oxide were de-termined with a gravimetric McBain-Baker micro balance incorporated in the B.E.T. apparatus. Isotherms are given for hexyl mercaptan on synthetic sphalerite at 25°C, 0.5°C and 50°C; on zinc sulphide at 25°C and 1.5°C; and on zinc oxide at 25°C. All these isotherms are sigmoidal, with a definite change in slope at or close to the mono-layer. The amount of mercaptan adsorbed below the monolayer increases almost linearly with relative pressure to P/P0 = 0.8.Above this value, the amount adsorbed increases very rapidly with relative pressure. Hysteresis loops appear in the isotherms for all adsorption-desorption cycles. These loops are completely reversible. It is not possible to desorb the mercaptan monolayer from any of the adsorbents, even at elevated temperatures."

Jan 1, 1966

By Chris M. Healey

"Abstract- The Jasper Gold mine in northern Saskatchewan produced a total mill feed of 140 127 tonnes at an average grade of 19.0 g/t Au. Both diamond drilling and chip samples from under­ ground workings returned extremely high values, up to 12 851 g/t (375 oz/I) Au over 0.10 meter from a chip sample. In the presence of such extremely high grades, the accurate estimation of reserves is a major problem.ln the first part of this study, production data from the mine were used to evaluate the results of a variety of reserve estimation techniques in this environment. In two out of three cases studied, indicator kriging with assays cut to 342.9 g/t (10 oz/I) gave extremely good results. In the third case, however , indicator kriging gave unacceptable results. Instead, lognormal kriging of uncut data gave the best results.Secondly, from the same database, a number of drill-hole spacings were simulated, and reserves estimated from the simulations. As may be expected, the results of this analysis show increasingly better results with tighter drill-hole spacing. However, even with a 5 m by 5 m spacing the variation from actual grade was quite large. This is not a systematic under- or over-estimation of grade, rather a random scatter of results .The results of this study show very clearly the problems of deriving good estimates of reserves when extremely high-grade samples are encountered. There is a high degree of randomness to this database, so reserve estimation in this situation will remain a high-risk operation."

Jan 1, 1993

By M. Marchese

It is no secret that scarcity of fresh water is an issue that at a global level in the years to come will have a major impact on the business landscape. A number of projects, beyond the mining sector, could remain on paper only due to this. At the same time, this situation is seeing the rise of new business opportunities, such as development of technologies for more efficient usage of water, water recycling, and desalinization of sea water. Despite that most of Chilean mining facilities are located in the driest area of the world, business has developed strongly and actively for more than a century. However, the negative effect on the water reservoirs and the environment is, lately, resulting in the reduction of the authorized water rights. Holding Water Rights for any given volume does not guarantee that the resource will be available when needed. A recent report from the United Nations on global climate change indicates that global warming can be directly related to changes in the natural and human environment. Chile would not be an exception. The reduction in snow levels in the high Andes and reduced rainfall during the so called "Bolivian winter", have directly affected the replenishing of the underground water reservoirs in the lower parts of the valleys, where most of the extraction of the resource takes place. Mining facilities shall be designed to reduce potential environmental effects, using proven technologies, and considering the best practices available. These measures shall constitute a complete structural framework for the environmental impact assessment (EIA) of the Project. The measures to prevent and mitigate the impacts on the water resources shall be considered during the design stage of a mining project. Current and future mining projects in Chile are conscious that the increasing pressure on the limited water resources is becoming unsustainable, and are already facing the water scarcity and social pressure by implementing sea water desalination plants, including long pressurized pipelines to the mine sites (e.g. Escondida, Candelaria, El Morro, Regalito). This paper presents, in summary, an analysis of the present and potential future scenarios.

Jan 1, 2007

By V. G. Papangelakis, S. Peters

Pressure oxidation of refractory gold ores can be conducted on ores with high carbonate content using just water or water with alkaline reagents to promote fast kinetics, and suppress the formation of elemental sulphur and CO2. In this work, a fundamental study was conducted to explore the silica-pyrite interaction in the presence of calcium and sodium carbonate. It was found that an alkaline environment increases the pyrite decomposition kinetics on one hand, but on the other dissolves silica, which encapsulates the dissolving pyrite thus hindering ultimately its complete decomposition.

Jan 1, 2011

By Marc Symbaluk

Core Programs Current ? Aboriginal Involvement Program ? Adaptive Forest Management / Forest History Program ? Grizzly Bear Research Program ? Natural Disturbance Program ? Foothills Growth and Yield Association ? Foothills Stream Crossing Program ? Fish and Watershed Program ? Caribou Landscape Management Association ? Social Science Program ? Local Level Indicators Program ? Communications and Extension Program ? Geographic Information Systems Program ? Mountain Pine Beetle Ecology Program In Development ? Climate Change Program ? Forest Community Program ? Water, Quantity and Quality Program (Water for Life) ? Circumboreal Initiative ? Yellowhead Ecosystem Management Group

May 1, 2008

By Louis Frost

MINE ventilation has for many years been the subject of intensive study by numerous investigators who have presented their findings in forms that are understandable to the average mining man, and all this writer hopes to do is to review those findings in relation to the 'manager's' problem in mine ventilation. It would not, perhaps, be wholly correct to acclaim practical mine ventilation as an exact science, because of the many variables entering into the problem. Each mine has its own particular problem and ventilation characteristics. Fan design, in contra distinction to mine ventilation, is an exact science, but the designer cannot always take into proper consideration the practical variations to which each mine is subject. Fan designers, accordingly, are forced to base their design on such data as the mine manager or engineer is able to supply, and, when it is borne in mind that the mine characteristic is constantly changing, it is not at all surprising that fans do not always show efficiencies hoped for. In many instances, fans work far beyond the de-signer's limitations, and, in consequence, are an economic disability in the colliery cost-sheet, and it is of paramount importance that the colliery manager evaluate all the factors involved in relation to fan performance for the colliery to receive full benefit from its investment.

Jan 1, 1941

By Peter A. Hacquebard

Recent drilling programs have shown that the in-situ coal resources of Nova Scotia are very substantial. The grand totals of the measured, indicated and inferred categories amount to 232 m, 646m and 993 m tons, respectively. This vast quantity of coal occurs essentially in five main fields: Sydney, Mabou, Port Hood, Pictou and Springhill. The largest resources (84% of the total) occur in the submarine area of the Sydney coalfield. With a 65% recovery rate, there are at present 150m tons of proven, recoverable coal in Nova Scotia. At a predicted maximum annual production of 5 m tons, this amount equals a lifespan of 30 years. However, additional drilling, particularly in the Sydney offshore area, holds promise of increasing the recoverable reserve tonnage to at least 350 m tons. This figure may be compared with the 484 m tons production obtained during 191 years of mining (from 1785-1976). The geological appraisal of the remaining coal resources in the five fields mentioned is presented in three-dimensional diagrams, per individual seam and corresponding reserve area. In addition, the submarine extensions of the Sydney and Mabou coalfields are discussed in light of results obtained from off shore oil exploration wells. The terminology and standards of coal resource calculations are pointed out, and the phenomenon of seam splitting and its prediction from geological data is illustrated. The availability in Nova Scotia of either thermal or metallurgical coal is considered in relation to rank and sulphur content. This paper was presented in June 1977 at the 90th Annual Meeting of the Mining Society of Nova Scotia. The coal resource estimates, however, have been updated to include the results obtained with the offshore drilling in the Sydney Coalfield to November 1977.

Jan 1, 1979

By A. K. Mahto, B. Samanta

"A heuristic model was developed to simultaneously generate the ultimate pit and production scheduling at a mining project. The method consists of a preprocessing step to select a starter pit, the implementation of a genetic algorithm to optimize the pit and schedule of the starter pit, and a network-flow algorithm–based postprocessing operation to finalize the ultimate pit and production scheduling. Applied to an iron ore mine, the model pit and schedule produced a net present value 21% higher than the reference pit and schedule prepared by experienced field engineers.RÉSUMÉ Un modele heuristique a ete developpe pour generer simultanement l’ordonnancement de la fosse finale et de la production dans le cadre d’un projet minier. Cette methode comprend une etape de pretraitement visant a selectionner une premiere fosse, la mise en oeuvre d’un algorithme genetique pour optimiser la fosse et le calendrier d’execution de cette premiere fosse, ainsi qu’une operation de posttraitement basee sur des algorithmes de flux reseaux pour finaliser l’ordonnancement de la fosse finale et de la production. En l’appliquant a une exploitation de minerai de fer, ce modele de fosse et d’ordonnancement a genere une valeur actualisee nette (VAN) superieure de 21 % a l’approche de reference pour la fosse et l’ordonnancement developpee par des ingenieurs de chantier chevronnes. INTRODUCTIONLong-term planning for an open-pit mine involves two important activities: developing the ultimate pit and determining the optimum production schedule. To accomplish this, an ore deposit is discretized into a number of smallsized elements called blocks, which are presented in a 3D block model structure. Because of economic and slope criteria, only a certain set of mining blocks can be extracted from the deposit constituting a pit. During mining, these blocks must be extracted in a specific sequence known as the production schedule."

Jan 1, 2017

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

By J. Suarez Condezo, E. Herrera Alarcon

The Ilo Smelter Modernization Project will require treating the slag from the Peirce Smith converters in Slag Cleaning Furnaces using pig iron technology. Currently the slags from the converters show variable magnetite contents. The copper contained in this slag is recovered in Reverberatory Furnaces, where the smelting rate was improved due to the high silica content of the converter slag. Preliminary industrial tests where developed to clean the slag from converters using pig iron. The results showed that the magnetite content has a significant influence in this process. This work describes the actions that are being implemented in the converter operation to control the magnetite content in the slag in order to maintain the high copper recovery of the smelter when the new facilities are commissioned. This task will demand a strong control of both the slag chemistry and converter practices in order to get the copper recovery considered as the design criteria (~97.4%).

Jan 1, 2007

By Loris S. Russell

THE plains of southern Alberta constitute one of the classic areas of geological investigation in Canada, for it was here in 1874, and in 1881 to 1883, that George Mercer Dawson (1, 2, 3) made the pioneer observations that are basic to all subsequent work on the interior plains of Canada. Dawson's work was extended eastward by R. G. McConnell ( 4) and northward by J. B. Tyrrell( 5) , but it remained. for D. B. Dowling to re-examine Dawson's Bow and Belly River Area and to make certain necessary revisions in the stratigraphical system of his predecessor. In 1917, Dowling published his memoir, The Southern Plains of Alberta( 6) , which remained for over ten years the last word on the stratigraphy and structure of the area described. It is generally conceded that Dowling's work made known the existence of a great artesian basin beneath the semi-arid plains of southeastern Alberta. In addition, his structural studies greatly stimulated the search for natural gas and petroleum. The most recent general publications on this area by the Geological Survey are based on the field work of M. Y. Williams, E. J. Whittaker, W. S. Dyer, and P. S. Warren, between the years 1923 and 1926. Their results were embodied in the Calgary Sheet (7) and the memoir, Geology of Southern Alberta and Southwestern Saskatchewan (8). By this time, the number of geologists working in Alberta in the development of the petroleum and natural gas industries had become large, and in 1931 the Alberta Association of Petroleum Geologist~ offered the Donaldson Bogart Dowling Memorial Symposium on Stratigraphy of Southern Alberta( 9) , a most valuable series of papers descriptive both of the ,surface stratigraphy and that observed in the well records.

Jan 1, 1937

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

"In many gold deposits, a reasonable amount of the gold that remains in the cyanide leach tailing is associated with pyrite. Some gold plants have found it economical to incorporate gravity circuits on the cyanide leach tailing to recover the gold bearing pyrite before subjecting it to fine grinding, then recycling the ground pyrite back to the cyanide leach circuit. For low grade gold deposits the loss of gold bearing pyrite is exacerbated as the broader process economics normally favour a coarse grind (> 150 ?m). An option that has received attention over the last decade is to recover the gold bearing sulphides in the milling circuit by gravity, similar to the widely-practiced gravity recovery of free liberated gold. The modelling and simulation of a gravity gold circuit in a milling flowsheet is relatively simple compared with a gold bearing pyrite circuit, as the recycle advantages and breakage functions for gold and pyrite are quite different. This current work represents an attempt to simulate the gravity recovery of gold bearing sulphides in a milling circuit that also incorporates fine grinding, using relatively simple simulation models. The simulation results are further explored with reference to the economics of this type of circuit.INTRODUCTION It is well known that gold is associated with pyrite in most sulphide gold deposits and that the amount of gold associated with pyrite will vary from deposit to deposit. Most of the gold associated with pyrite is liberated in the grinding circuit during the processing of a gold ore. However, some gold remains occluded in the pyrite and is lost in the final leach tailings. Little information is available in the literature on methods to enhance gold liberation from pyrite by specifically removing pyrite, either in the grinding circuit or from the final tailings stream, and grinding it finer. One of the earliest record of this approach is described by King (King, 1949) where pyrite present in Witwatersrand gold ores was recovered by circular jigs and Johnson barrels followed by fine grinding of the concentrate prior to cyanide leaching. Dominy et al., 1970, provides information on the use of Yuba jigs to recover pyrite from the discharge end of ball mills. Again, the jig concentrate was ground to a fine particle size before cyanide leaching to recover the liberated gold. Unfortunately, no information is provided in these articles on the additional gold recovery from implementing these circuits in a flowsheet. Martins et al., 1993, provides details of a gravity circuit using Reichert cones and spirals to recover gold bearing pyrite from a cyanide leach tailings followed by fine grinding of the pyrite concentrate in a Tower mill. The ground concentrate returned to the front end of the already installed leach circuit. Overall recoveries were increased by some 2% to 4% depending on the amount of gold and pyrite in the plant feed."

Jan 1, 2017

By K. Maruyama, T. Nagasaka, R. d. Chairaksa-Fujimoto, T. Miki

Electric arc furnace dust or EAF dust is considered as a hazardous waste but contains a significant amount of economically attractive non-ferrous metals especially zinc as zinc ferrite (ZnFe2O4) and zincite (ZnO). The hydrometallurgical process is one alternative choice because it has the advantage of low energy consumption. The leaching of ZnO from the dust is very easy. However, the complex major zinc compound in EAF dust is ZnFe2O4, which is very stable and insoluble in alkaline or acidic media under delicate conditions, and causes the low zinc recovery yield by hydrometallurgical process. Moreover, halogens and heavy metals in the dust are also problematic. In order to develop a new effective EAF dust treatment process, the authors have proposed "CaO addition process" as pre-dust treatment to transform all of ZnFe2O4 in the EAF dust to ZnO and Ca2Fe2O5. In this study, the selective zinc leaching from the CaO treated EAF dust with NaOH and NH4Cl solutions was carried out. The effect of temperature, reaction time and solute concentration were systematically investigated. All of zinc in CaO treated EAF dust was successfully leached into both solutions.

Jan 1, 2014

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012