Search Documents

?Four-wheel, skid-steer, rover developed for CSA ?U-chassis for payload accommodation ?Passive geometric suspension ?Max speed 13km/hr ?Remote workstation ?275kg payload capacity ?On-board processor, IMU, motor encoders ?5.2kW-h battery capacity

May 1, 2013

By E. H. Henderson

Introduction Stamp-Milling and amalgamation is, perhaps, one of the oldest processes of recovering gold from its ores. Many papers, theses, and textbooks have been written on the subject of stamp-milling practice in general, but, to my knowledge, there have been no publications describing the modern stamp-mill as designed, developed, and operated in Nova Scotia. Although it may be said that the gravity stamp-mill is the most primitive, and perhaps the crudest, crushing machine in existence, it is at the same time the most satisfactory all-round milling and amalgamating device yet contrived. Originating in Saxony, and used in North America first in Virginia and Georgia, the stamp-mill, in a primitive form, later found its way to California and Colorado. Here, it speedily developed from an affair of wood shod with iron, and operated with the crudest gearing, to substantially its present form. Briefly, it consists (see Figure 1) essentially of a series of hammers (the stamps), which fall upon a mixture of ore and water contained in a cast-iron box (the mortar). The resulting crushed ore (the pulp) is splashed out through a screen on the front of the box. For some years after the discovery of gold in Nova Scotia, in 1861, the ? arrastra and Chilean mill were used to recover the gold from the rich ores. The stamp-mill followed, and various types were used, principally the California and Gilpin County types. Then, in 1895, Mr. M. R. O'Shaughnessy, one of our foremost amalgamators, conceived the idea of a new type of stampmill, which has since become standard in Nova Scotia gold mines. This mill, unique in its design and operation, is specially adapted for the most efficient extraction and recovery of gold as it occurs in our Nova Scotian ores. It is commonly known as the Underwater Feed type, as opposed to the usual Overwater or Top Feed type, and it may be rightly termed The Nova Scotia Self-Classifying Stamp Amalgamation Mill. It is conceded by experienced mill-men that it is superior to any other type of mill for recovering the very coarse and granular gold typical of the ores of this Province. The particular installation and practice to be described in this paper is that of the Guysborough Mines, Limited, at Goldenville, Guysborough county. Emphasis will be laid on certain operating innovations of extreme simplicity and high efficiency.

Jan 1, 1935

By M. Nusheh, C. Bumby, A-H. Puichaud

"Vanadium-bearing titanomagnetite ironsand deposits occur along a 480 km stretch of the west coast of New Zealand. In the present study, the leaching behaviour of NZ ironsand was investigated in hydrochloric acid (2–10 M) solution at 50–80°C for 2 h. The resulting leaching liquors exhibited Fe/V ratios in the range 150–180. The distribution of trace element contaminants between solution and solid residue was investigated, and processing conditions have been determined for rapid and efficient dissolution of Fe, Ti and V into the leaching solution. In addition, mineralogical analysis of raw ironsand and leached residues was performed in order to study the leaching mechanism. Samples were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy (EDX), X-ray fluorescence spectroscopy, qualitative and quantitative X-ray diffraction and inductively coupled plasma mass spectrometry (ICP). Results indicate that the dominant dissolution process follows shrinking particle mechanism. However, ironsand particles containing ex-solution lamellae exhibited a different leaching behaviour compared to homogenous titanomagnetite particles.INTRODUCTION Titanomagnetite ironsand (blacksand) forms Quaternary onshore beach and dune deposits and offshore marine deposits (Figure 1) along 480 km of coastline from Kaipara Harbour south to Wanganui on the west coast of the North Island (Christie, 2016). It attracted the attention of scientists from the earliest times (Galbreath, 1998). The principal minerals in ironsand are titanomagnetite (TTM), ilmenite, quartz and ferromagnesian minerals such as augite, hornblende, diopside, and olivine with smaller amounts of rutile and apatite (Mauk, 2016).Several large ironsand deposits have been discovered and exploited since the late 1960’s. The Waikato North Head and Taharoa mines are currently operating and they have a 2015 measured resource of 400 million tonnes in total and provide over 2 million tonnes of concentrate per year by simple cost effective magnetic separation process (Christie, 2016; Christie & Brathwaite, 1997). The concentrate contains not only 7–8% TiO2 and 56–60% SFe, but also 0.3–0.6% V2O5, is both a valuable titanium mineral and a source of vanadium. All the production is used for steelmaking industries. The other potential for utilizing more of this resource without requirement of integration into an iron and steel producing plant is to develop a hydrometallurgical route with advantages of higher efficiency along with lower emissions. Currently, there is no existing commercial process capable of extracting all three of these elements as industrial-grade commodity products. Acid leaching of TTM concentrate with higher degrees of recovery and selectivity is a key step in any possible hydrometallurgical route."

Jan 1, 2017

By P. Nos, L. Kolbeinsen, M. W. Kennedy, A. Filzwieser, R. T. Jones, A. MacRae

Modern furnace designs often incorporate extensive use of cooled elements to achieve long campaign lives at high operating intensities. However, contact between water and high temperature fluids can result in powerful Boiling Liquid Expanding Vapour Explosions (BLEVEs). Therefore cooling such elements with water carries inherent risks when used under slag and particularly below molten metal or matte. Alternative cooling media exist that can reduce or eliminate the risk of BLEVEs. These media are analysed and discussed in the context of deeply cooled furnace elements. Important factors in selecting alternative coolants are explored including: critical heat flux, thermal limits, toxicity, flammability, unit cost, etc. Key cooling system design criteria are reviewed in the context of both traditional and alternative coolants. Results of Computational Fluid Dynamics are presented for an example tap-block cooler design using a number of selected coolants. Research needs to advance the safe use of alternative coolants are presented.

Jan 1, 2015

By C. H. G. Bushell, G. Brown, C. J. Krauss

1N FLOTATION, copper sulphate is used universally for the activation of sphalerite and marmatite and, to some extent, for the activation of other minerals. The copper activated surface readily adsorbs standard collectors such as the xanthates and dialkyl dithiophosphates whereas untreated zir~ sulphide does not. With the host of reagents available, making a mineral float is seldom difficult. The problem is to achieve selective flotation. In zinc flotation, the great value of copper sulphate results from its ability to activate zinc sulphide preferentially to gangue minerals. At the Sullivan Concentrator of The Consolidated Mining and Smelting Company of Canada Limited, the most abundant gangue mineral in the lead-zinc ore is pyrrhotite, and the zinc mineral is marmatite of somewhat variable zinc to iron ratio. For this Cominco study, selectivity between marmatite and pyrrhotite was therefore the most interesting aspect of copper sulphate activation.

Jan 1, 1961

By Fathi Habashi

The year 1987 marked the centennial of the beginning of modern hydrometallurgy. On October 19, 1887 British Patent No. 14174 entitled Process of Obtaining Gold and Silver from Ores was issued*. The discovery was made by John Steward MacArthur (Fig. 1), a chemist-metallurgist, supported and assisted by Robert and William Forrest, two brothers practicing medicine in Glasgow. The discovery was made in the basement of their clinic. The process, which became known as the cyanidation process in reference to the alkali cyanide reagent used, immediately received industrial success in New Zealand in 1889 and in South Africa in 1890t. It displaced the chlorination method which had been in use. In 1903 MacArthur was awarded the first Medal of the Institution of Mining and Metallurgy in London1131 - The cyanidation process was responsible for the doubling of gold production in the world in the two decades which followed its first application (Fig. 2). To the modern metallurgist, it may be surprising to think of MacArthur coming across an obscure reagent such as an alkali cyanide as a leaching agent for gold ores. It is the purpose of this paper to discuss the background and the factors that led to this invention, the development of the understanding of the process, and the application of modern technology.

Jan 1, 1999

By C. P. Jenney

"Exploration for copper, in a region of 7,000 square miles on the Arctic coast between longitudes 114 and 118 degrees west, has covered a period of nearly 200 years. Occurrences of native copper, used by the natives for tools and weapons, have been reported since the early part of the eighteenth century. In J 771 Samuel Hearne of the Hudson's Bay Company, in the course of his classic 3-year journey from Fort Churchill, became the first white man to see the deposits, and incidentally the first to reach the Canadian Arctic coast by land. During the next 140 years the deposits were mentioned by every explorer and traveller who passed through the area. A good historical summary of this literature has been presented by Tyrrell (1912).In 1911-12 the Douglas-Sandberg party did the first geological mapping along the Coppermine River and Dismal Lakes (Douglas, J., 1913; Douglas, G. M., 1914), and described the copper occurrences there. In 1914 J. J. O'Neill (1924) of the Canadian Arctic Expedition investigated the showings on Bathurst Inlet. In 1929-31 two Canadian exploration companies sent prospectors and geologists to the area (Gilbert, 1931; Norrie, 1931; Duncan, 1931). Since that time only brief references have been published (Kidd, 1931; Stockwell and Kidd, 1931; Lord, 1941, 1951; Washburn, 1947). In 1943-45 an area of more than 1,500 square miles was prospected by American Metal Co. of Canada, Ltd., under the direction of the writer. Forty-nine showings were examined; seven of these were mapped in detail by plane-table and two were sampled by 27 short diamond drill holes totalling 3,061 feet. All holes were in permanently frozen rock, and the deepest vertical distance reached was 206 feet. Five groups of claims were staked. These later lapsed, but one of the groups was restaked in 1951, and assessment drilling and some trenching were carried out in 1952-53. Results were disappointing, and the claims have been allowed to lapse.The area is within the Arctic Circle, northeast of Great Bear Lake and 360 miles north of Yellowknife on Great Slave Lake. For exploration purposes, access is by aircraft from Yellowknife. During the short open season heavy freight can be brought by sea to Coppermine at the mouth of the river, either from Aklavik at the mouth of the Mackenzie or around Alaska. Concentrates would have to be moved by these routes.Although none of the deposits so far found is mineable under present conditions, the total volume of copper in the numerous showings marks the district as a major area of copper mineralization, which may some day be of economic importance."

Jan 1, 1949

By R. K. Collings

"This paper summarizes research that was done at the Mines Branch, Ottawa, to evaluate samples of phosphogypsum for gypsum products manufacture. The samples were from phosphate fertilizer facilities at: Port Maitland, Ontario ; Valleyfield, Quebec; and Fort Saskatchewan and Redwater, Alberta. All samples were wet-screened, washed, filtered and calcined in a laboratory kettle at atmospheric pressure. Tests were also made at higher pressures in a small autoclave. The gypsum and resulting hemi-hydrate, being acidic, were treated before, during and after calcining with various bases. The hemi-hydrate products were checked for time of set, compressive strength and bond to gypsum wallboard paper. The results of this study indicate that phosphogypsum from each of the sources investigated has potential as a substitute for mined gypsum in gypsum products manufacture. Pilot-scale testing is recommended to confirm that the product would be satisfactory for the manufacture of plaster products on a commercial basis."

Jan 1, 1972

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By R. M. Graves, C. B. McKenzie, D. Barbour, D. W. Desnoyers

"Abstract -The prospective Tulks volcanic belt hosts five significant massive sulfide deposits, Tulks Prospect, Tulks East, Jack's Pond, Daniel's Pond and Victoria Mine, as well as numerous showings and indications throughout its 70 km outcrop length. Regionally, the 498 Ma sequence consists dominantly of felsic pyroclastic rocks and flows with interbedded mafic volcanic units and fine­ grained sediments, commonly graphitic. Contemporaneous granitoid rocks occur in the south half of the belt. Rocks usually display a strong NE-SW, steeply dipping, penetrative foliation and other shear-related high-strain fabrics. Facing directions are normally northwest, although there is local evidence of folding. Sulfide bodies and their alteration systems are deformed and shape-modified in the style of ambient strain.The Tulks, Tulks East and Jack's Pond prospects appear to occupy a similar stratigraphic level, on or near the contact between a thick felsic pile and an overlying broad, conductive package of graphitic sedimentary rocks. AU are pyritic deposits with well-developed footwall alteration systems. The Tulks prospect comprises four polymetallic lenses totalling 750 000 t. Three lenses constituting more than 6 000 000 t of sulfide mineralization are indicated at Tulks East but only the 210 000 t ""B"" lens contains significant base metals. Jack's Pond consists of a very extensive, zoned alteration complex in which four lenses of massive to semi-rnassive pyrite + chalcopyrite are known.The central part of the system, characterized by Mg chlorite and carbonate, is enveloped by pervasive sericitization and capped by intensely silicified and pyritized volcanics. The sulfide lenses are interpreted as part of the footwall zone and are beneath that part of the system most likely to host polymetallic massive sulfides.Daniel's Pond differs from the other prospects in such fundamental ways as metal content, associated alteration and structural setting. The deposit comprises strongly tectonized, Ag-rich, Zn-Pb mineralization distinguished by a pronounced Ba-As-Sb signature. Mineralization is confined to a narrow, north-south high-strain zone which separates unstrained mafic volcanic rocks to the east from well-foliated felsic rocks. The deposit Jacks an extensive alteration halo and at its north end is associated with a lens of barren, undeformed massive pyrite.The Victoria Mine deposit, the most cupriferous of the five, is related to a moderately dipping structure that separates well-foliated Tulks volcanic rocks from an overlying, Jess deformed volcanic­ sedimentary sequence that may be as young as 462 Ma. The structure is also the locus of black chlorite, dolomite and quartz alteration. Structurally remobilized precursor sulfide mineralization is one possible source for the deposit."

Jan 1, 1993

Operating CIP/CIL gold recovery plants in the arid regions of Western Australia face unique challenges due to water and ore quality issues. The presence of cations of Mg, Fe and Cu metals in water supplies and leached sulphide ores can have considerable effect on plant consumption of lime and cyanide, due to pH buffering and complexation effects. Reagent costs are critical to many of these operations. In this paper, computational modelling is used to analyse a number of process options to mitigate such issues. This requires careful consideration of the chemistry of the process system, and the ability to predict accurately the response of speciation and precipitation reactions to changing process conditions. The Mg-Fe-Cu-CN-H20 system is specifically modelled in this application. The Gibbs Free Energy Minimisation thermodynamic framework has been selected to model equilibrium phenomena. Furthermore, this approach has been extended to the process flowsheet level, incorporating multiple unit operations and recycle streams in a steady-state mass balance model. The Gibbs equilibrium composition module of HSC Chemistry software has been successfully integrated into the commercial flowsheeting package SysCAD. Consideration of the Gibbs Energy Minimisation capabilities of other flowsheeting packages has also been given. This approach has been successful in simulating the aqueous process chemistry typical of such plants. It has resulted in a predictive capability where equilibrium states respond appropriately to process changes. Potential cost savings may be identified by examining alternative process conditions to minimise overall reagent consumption.This methodology may be extended to other hydrometallurgical plants where issues of solution ideality, temperature and other equilibrium processes are sufficiently understood.

Jan 1, 2005

By Tassos Grammatikopoulos, Vladimiros Papangelakis, Douglass Duffy, Cheryl Washer, Srinath Garg

Flotation operations in Sudbury, Ontario, seeking to separate pentlandite and chalcopyrite from mixed sulphide deposits, produce pyrrhotite tailings that have been disposed of in tailings ponds for over 50 years. These reactive tailings are viewed as waste, despite containing ~0.8 wt% Ni, and represent an environmental liability because of their acid mine drainage (AMD) potential. Given the large quantities of pyrrhotite currently stored in Sudbury, and declining ore grades elsewhere, these tailings have shifted from being viewed as a waste to a potential resource. Recent advances in the bioleaching of low-grade sulphide ores have raised the prospect of bioleaching as a potential low-cost processing option. However optimization of this proposed process requires a thorough understanding of the mineralogy of the pyrrhotite tailings that would be leached. The work presented here addresses the characterization of two distinct Sudbury pyrrhotite tailings, namely from the Vale and Glencore operations, using electron microprobe, XRD and QEMSCAN analysis. Particular focus is given to how the mineralogy may affect bioleaching as a processing option, through the deportment of nickel and the various phases present

Jan 1, 2015

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

By Cheryl Devine, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg

The microbial-mediated recovery of valuable metals locked in mining wastes presents an economical alternative to conventional hydrometallurgical processes. The present study investigated the bioleaching response of a low-grade nickeliferous pyrrhotite tailings (0.6 wt% Ni) and an upgraded pyrrhotite tailings (1 wt% Ni) produced by Vale Base Metals in the Sudbury Basin of Ontario, with the ultimate aim of maximizing Ni recovery. The initial part of the study focused on the bacterial adaptive evolution protocol, by repeatedly sub-culturing an indigenous culture from an acid mine drainage site on 2% (w/v) pyrrhotite tailings. The results showed that the extent of Ni dissolution is positively correlated with microbial activity. Microbial profiling revealed A. ferroxidans to be the dominant member of the microbial consortium. The enriched culture was used for optimizing the growth medium by varying the concentration of essential growth nutrients. Finally, an aerated biotic and abiotic leach of a 10% (w/v) upgraded pyrrhotite tailings with and without pH control, showed a higher recovery of Ni in the pH controlled experiments. These results demonstrate that a high concentration of the oxidant Fe3+ in solution promotes the dissolution of Ni. Furthermore, the sulphide conversion into So was found to be higher in the pH controlled experiments (32%), relative to the experiment without pH control (10%).

Jan 1, 2015

By W. P. Campbell

THE investigation herein described had its beginning in the chemical laboratory of the Department of the Interior, Calgary. After the transfer of the natural resources to the Province of Alberta in 1930, the laboratory was closed and the investigation discontinued, but in 1933, with the permission of the Director of the Mines Branch, the work was again taken up and brought to completion. OBJECT OF THE INVESTIGATION The object of the investigation as originally planned may be stated as follows : (1) To determine the chemical composition of the limestone formation underlying Turner Valley gas field. (2) To identify 'beds' in the limestone, if such existed, with definitecharacteristics which would mark them from immediately overlying and underlying measures. (3) To relate information acquired on the composition of the limestone to the occurrence of oil and gas in the particular section examined. Definite information was lacking as to the exact chemical composition of the limestone and of its variations in composition at various depths. The formation was generally referred to in the field as the 'dolomitic' limestone, but the depth to which the dolomitized zone extended and the degree to which the limestone generally had become dolomitized were not known. Jn the drilling and logging of wells, the recognition of suitable 'markers' in the various formations is a matter of some importance. Markers are generally relatively small but widespread members of a formation, which have some characteristic property, of colour, composition, or form, by which they may be identified, and with them, consequently, the formation of which they form a part. In the formations above the limestone in Turner Valley, a number of well defined and easily recognized markers are known to geologists, drillers, and others interested in the field. Many of these markers Hand out in sharp contrast to adjoining measures and are therefore easily recognized; in others, the contrast is less sharp, with consequent difficulty in identification.

Jan 1, 1937

By Mehmet Guney

This article is based on a detailed heat investigation conducted at the Rokana Division of Nchanga Consolidated Copper Mines Limited while both authors were employed in Zambia. Mindola Mine is one of the three underground mines comprising the Rokana Division on the Copperbelt of Zambia, producing about 270,000 tons of ore per month at 1.9% Cu and 0.14% Co. The total volume of air being circulated by means of five primary fan installations slightly exceeds 1,000 m3/sec at standard density. Sectional bulk cooling is practised where air cooling coils are installed at primary splits some considerable distance from the stoping operations. Total capacity of the refrigeration complex is 10,500 kw (3,500 R. tons), of which about 7,000 kw is available as effective cooling power after losses, but the heat removed from the coifs is about 3,500 kw with 61% over-all plant performance. An extension program is planned for a further five production levels with the re-deepening of a sub-vertical shaft. Thermal heat will become a major problem at increased depth associated with higher rock temperature, higher thermal conductivity of the rock groups encountered and fissure water flowing into working areas through the strata with increased rock temperature. This paper describes the ventilation and refrigeration practices in Mindola Mine, with special reference to future thermal heat problems. These are discussed with a view to mining at depth.

Jan 1, 1979

By Norman A. Grant

"Location and Transportation FacilitiesTHE BEAVERLODGE area of North Saskatchewan is on the north side of lake Athabasca, 500 air miles northeast of Edmonton.The main Eldorado operation and townsite are on the north •side of Beaverlodge lake, which is immediately north of lake Athabasca and is separated from it by only a mile long portage at Lodge bay. The once famous town of Goldfields. Saskatchewan, and the Box property of the Consolidated Mining and Smelting Company of Canada, Limited, are located on lake Athabasca nine mines from Beaverlodge townsite.Previously, all Eldorado freight was delivered by barge at the Lodge Bay portage, hauled across the portage, and across Beaverlodge lake by small Northern Transportation Company barges, which involved many handlings.In 1952 the port of 'Bushell' was established at Black bay. This is a particularly snug harbour, well protected from the main body of the lake and with good foundations for docking facilities. A Butler building, 300 ft. by 60 ft., and tank farms provide storage at the port. A •road from Bushell to the main Beaverlodge operation, a distance of twelve miles through rugged terrain, was built by the Saskatchewan Government. The cost was shared by the Saskatchewan Government, the Federal Government, and Eldorado and other mining companies.Along this road are located the properties of several enterprising mining companies and near the midpoint lies the ambitious budding town of Uranium. This road has made portaging unnecessary and palletized freight loaded at Waterways, Alta., is now loaded directly on trucks at Bushell and delivered to the point of consumption."

Jan 1, 1953

By Farzaneh Abedini, Narain Hariharan, Lucas C. McFarlane, Nikolas A. Romaniuk, Tiffany Thayne

The use of dewatered mine tailings as backfill material (commonly referred to as ‘paste’ backfill), is the most practiced form of backfill in Canada providing significant environmental benefits by reducing the size of external tailings facilities and improved economics through enhanced resource recovery. Paste backfill operations reuse filtered mine tailings with a cementitious binder and water to create a slurry that is hydraulically transported to refill underground stopes, later forming a structural network of cemented tailings in the mine stopes. Unlike typical structural applications that utilize General Use (GU) Portland cement; modern paste backfill operations maximize strength performance by blending Portland cement with ground granulated blast furnace slag (GGBFS) or other supplementary cementitious materials (SCMs). GGBFS and other SCMs offer key performance benefits and carbon reductions; however, the availability of these SCMs is rapidly dwindling in today’s carbon-constrained economy. This paper examines the development of an alternative binder system that provides similar performance and carbon reduction to that of GGBFS for mine backfill operations. The binder utilizes the chemical reaction between a reactive source of aluminosilicates and available calcium from calcium oxide or calcium hydroxide to replace between 50 to 100% of GGBFS. The performance of the binder is examined with insights into the hydration mechanisms that generate mechanical strength in the cemented paste network. Paste backfill slurries require precise engineering to create a material that maintains flowability during pipeline transport and generates enough strength to meet operational targets once placed in the stopes. Engineering of such slurries requires large amounts of water to be added to the binder-tailings matrix, far exceeding the typical water to binder ratios used in concrete mix designs. This characteristic of paste backfill warrants great emphasis on understanding the hydration mechanisms of the binder used in the paste backfill system. GU cement is typically composed of 50-70% tricalcium silicate and 15-30% dicalcium silicate.  The hydration mechanisms of these compounds consume 4 to 6 units of water to mineralize into calcium silicate hydrate cemented phases that result in compressive strength development. Cementitious aluminate and aluminosilicate phases make up 5-20% of GU cement and aid in secondary performance characteristics such as set time. Certain calcium aluminate hydrate phases such as monocarboaluminate and ettringite mineralize 10 to 32 units of water into their crystalline structure. Hydration products such as ettringite are traditionally avoided in construction applications due to their propensity for volumetric expansion after cement setting, leading to micro-fissures and subsequent strength degradation (known as ‘sulfate attack’). This paper proposes that such hydration products benefit the strength development in paste backfill slurries with the aforementioned characteristics due to their greater potential to mineralize free water. The newly developed calcium aluminosilicate binder is designed to replace 50-100% GGBFS or other SCMs used in paste backfill systems and meet operational strength requirements by providing exceptional hydration characteristics through cementitious reactions. Additionally, the aluminosilicates used have a minimal carbon footprint and a secure supply outlook, thereby allowing mine operators access to a low-carbon binder option throughout the mine’s lifespan.

May 4, 2025

The methods employed for the addition of uranium to steels and cast iron in the Physical Metallurgy Division are outlined. It has been found that the segregation of? uranium is a major problem in aluminum and/or silicon killed steels and that the cooling rate is important in al-lowing the segregate to settle to one area, which can subsequently be discarded. The unsegregated areas were found to be extremely low in total oxygen, acid insoluble aluminum (AizOg) and, in some cases, slightly lower in nitrogen. Uranium recoveries, based on analyses of the unsegregated areas, were quite constant, at about 45 per cent, regardless of the type of uranium master alloy used for the addition. No segregation of carbon, manganese, silicon, sulphur, phosphorous, chromium or copper was observed in these steels. In commercial heats, the recoveries ranged from 7 to? 29 per cent for ladle additions to oxygen converted steel. When the steel was fully deoxidized prior to the uranium addition, recoveries ranged from 49 to 66 per cent, regardless of the steelmaking process.

Jan 1, 1964

By Y. Wang, S. Liu, K. Jiang

China is the world’s largest producer and consumer of non-ferrous metals. In recent years, significant progress has been made in research and commercial application of pressure leaching technology to produce some nonferrous metals. Research and development activities include a low-pressure, low-temperature leaching technology for complex copper concentrates, a hematite process to treat pressure leach solutions from zinc concentrates, and a pressure leaching - solvent extraction process for molybdenum and rhenium. Examples of commercial practices include a two-stage pressure leach technology in a zinc plant in Danxia, a direct leaching technology in a zinc plant in Zhuzhou, a high pressure acid leaching process for a nickel laterite project in RAMU, and a pressure leaching technology to treat arsenic sulfides in a plant in Guixi. The development of pressure leaching technology for the recovery of lead, vanadium, gallium, germanium, and precious metals in China will also be described in this paper.

Jan 1, 2015