Search Documents

By Claude A. Jr. Seger

Introduction This paper presents in detailed form the results of settling tests that were published in a few preliminary notes in the April 1949 issue of the Bulletin (p. 166). Carborel is the trade name for sodium carboxymethyl-cellulose and aluminium carboxymethyl-cellulose produced by the reaction of monochloroacetic acid on the alkali cellulose to form an ether. The water-soluble sodium carboxymethyl-cellulose has been known in Europe for several years as sodium cellulose glycolate and has been marketed under several trade names. These cellulose ethers, however, are relatively new in North America, where the name carboxymethyl-cellulose is often abbreviated to C.M.C., or they are referred to as cellulose gum. The particular grade of Carboxel used in the settling tests in the mill of Chesterville Mines, Limited, is the high-viscosity sodium carboxymethyl- cellulose known as Carboxel H.V. It is a white, fluffy powder and is hygroscopic, although not deliquescent. Carboxel solutions in water are colourless, odourless, and resistant to beat and light. They are stable to alkalies, but are precipitated by acids when the pH is reduced below 4.0, and also by solutions of soluble lead, iron, copper, aluminium, and chromium salts. Solutions of Carboxel exhibit the properties of hydrophilic colloids.

Jan 1, 1949

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

By George Kellock

Introductory The Alberta Provincial Government has contemplated a revision of the Mines Act for some time past, and it is understood that a definite decision has now been made to do this at the next session of the Legislature. The Operators' and Miners' organizations of the Province have been asked, or at least have been given the opportunity, to submit their views and ideas relative to the proposed changes. The operators have already drafted out a number of changes which they feel would improve the Act from the standpoint of safety and practicability, and this paper has been prepared so that the general membership of the Rocky Mountain Branch of the Institute, which is composed largely of the operating and certificated officials of the mines, might have an opportunity to discuss, criticize, and improve upon the suggested changes which the operators are putting forward.

Jan 1, 1929

By K. H. Kretzschmar, M. A. Smith

A brief review of the rapid growth of ACT in Western Canada is presented. It is remarked that this rap-id growth has been accompanied by a heterogeneous approach to design. A more rational and consistent approach is suggested, together with the assumptions on which this approach is based. The operating history of some existing installations is discussed briefly, and conditions necessary for the continued growth of ACT are outlined.

Jan 1, 1960

By Thomas. L. O.

Apart from a few sketches and incomplete maps, mainly topographical, and one or two detailed maps of placer-creeks, there is little information on the topography and geology of most of the country adjacent to the sections of the Alaska Highway in the Liard River area, particularly that part east of Kechika river. In 1943, the Geological Survey of Canada made a recon-naissance from Fort Nelson clown the river of that name to the Liard, thence up the latter to Hell Gate, and also up Beaver river for a distance of fifty miles. The whole of the area covered was found to be underlain by sedimentary rocks, not a single igneous dyke being seen. The British Columbia Department of Mines began reconnaissances near the highway both in and north of the drainage basin of Prophet and Muskwa rivers with a view to finding structures favourable for the accumulation of oil. In Liard River valley near the mouth of Smith river and at intervals from there clown to Devil' s Portage occur warm springs whose character and origin are not definitely' known, since they have not been investigated (21, p. 38A). Similar springs are said to occur at several localities over a broad belt extending from Muskwa river across the Liard to the Nahanni River country (26, p. 11). On Liard river below the mouth of Dease river, stratified sands, gravels, and clays of Pleistocene (?) age are constantly met with and in one or two places are underlain by sandy clays. The distribution of the latter, however, is very limited in the section cut by the river west of the Rocky mountains. The only range of these mountains that reaches the Liard is the high limestone ridge which approaches the mouth of Vents river from the southeast and then almost vanishes a few miles to the northwest of it (27, pp. 43-45). In general, the ranges of the Rockies in the area under consideration have been but little explored, but they are undoubtedly very largely sedimentary and, with the exception of some volcanics and intrusives on their western flanks, are probably almost entirely so. Unlike the high, deeply incised ranges in southern British Columbia, they dwindle in elevation north of Terminus mountain to low-wooded ridges separated by wide swampy valleys, and practically lose their identity between it and the Liard. The foothills, which, along the Liard, have a width of 38 miles (from near the mouth of Trout river to Hell Gate) are composed of a great series of alternating shales and sandstones, with some limestones, all folded closely together, which resemble those found in the foothills farther south (27, pp. 50, 19-20).

Jan 1, 1944

By V Dolmage

In 1957 and 1958, ten topographically suitable damsites were investigated along the Peace river between Finlay Forks and Hudson Hope, B.C. Of these, three were eliminated after a reconnaissance survey indicated that the geology was unsuitable for the 650-ft.-high dam contemplated. ?After extensive drilling, five other sites were deemed unfeasible because of geological factors and, in 1959, the two remaining sites were designated as being suitable, one for the high dam and the other for a low dam downstream. The sites are located in the Peace River canyon, on the west and the south? side of Portage mountain, west of Hudson Hope. The site for the large dam, the Portage Mountain dam, has since been investigated by surface mapping, thousands of feet of diamond drilling, a seismic survey, laboratory rock tests and on-site grouting tests in order to establish the possible effect on the dam of all facets of the foundation rocks. Three diversion tunnels, 50 ft. in diameter and 2,200 feet in length, have been driven through massive sandstone and shale, and an intake cut, 500 ft. in length, 200 feet in width and 200 feet in depth, has also been excavated in rock.

Jan 1, 1963

By G. M. Hutt

Introduction The major development of industrial minerals in Manitoba has been in building materials. 'The building-stone industry is developed far beyond the needs of the Province, and the well known Tyndall limestone is marketed over a wide area throughout the other provinces to Canada. Similarly, gypsum and gypsum products are produced in excess of local requirements and are exported to adjacent provinces. The crushed-stone, sand and gravel, limestone, and lime industries are sufficiently developed to supply the needs of the Province and, notably in the case of lime and lime-stone, there is a surplus for export to the adjacent provinces and to the United States. The manufacture of common brick is well established, but for face-brick and other clay products the Province is dependent largely on importations. Production of silica-sand will increase as Canadian markets become available through recognition of the utility value of the Black Island sand as foundry-sand and for other purposes. There is some possibility of the export of feldspar, of lithium ore and concentrates, and perhaps of salt. A considerable part of the Province has not been seriously prospected for industrial minerals and it may be expected that, as time goes on, other deposits of non-metallic minerals will be discovered and opened up, especially as the prairie provinces become more industrialized. At the present time, there is some activity in the southern part of the Province based on gas and oil indications. Whatever may be the outcome of this work, it should yield valuable information concerning the geological structure of the area.

Jan 1, 1934

By Terry A. Lee

The grade of mineral resource estimates underpin all major economic considerations of mining prospects. While there are reporting requirements to satisfy when stating a mineral resource estimate, an examination of NI 43-101 style reports suggests that authors believe that there are a number of ways of addressing these requirements. As a reader of these reports, some processes are helpful and others are not so in getting a real appreciation of how realistic is the mineral resource estimate. Critical to the quality of the mineral resource estimate is how realistic is the economic mineral concentration component. In many cases, this parameter is called grade. The industry experiences increased difficulty in achieving realistic grade estimates as the sample grade variability increases. The level of transparency in a mineral resource estimate is very much a function of the competence of the author. An objective presentation of the critical data, such as grade sampling variability can assist a reader in determining if the geology of the mineral concentration is adequately understood and how realistic is mineral resource grade estimate. This paper has considered 75 NI 43-101 style reports released in the past 2 years. The review demonstrates features that were helpful in determining how realistic the mineral resource grade estimate is. If there is insufficient transparency in a report, there is a high probability that the mineral resource grade estimate will not be realistic.

Apr 1, 2005

By Patrick Mclaren, Peter B. Hale

Canada, with one of the largest continental shelf areas in the world, has done little to evaluate its offshore unconsolidated mineral resources which include heavy minerals (gold, chromite, rutile etc.) and industrial minerals (silica sand and aggregates). During glaciation much of the continental shelf was covered with an ice sheet and later subaerially exposed with the result that glacial, glaciomarine and fluvial processes deposited sediments that may contain heavy minerals derived from onland locations. With rising sea-levels, beach and nearshore processes may have served to concentrate heavy minerals by winnowing and removing the lighter mineral components. These potentially valuable resources can be found with suitable exploration techniques such as seismic profiling and bottom sampling. Gold deposits are known to exist off the coast of Nova Scotia, and on the basis of form er beach mining, gold deposits probably occur off Vancouver Island and the Queen Charlotte Islands. Large deposits of silica sand occur near the Madeleine Islands and it appears likely that supplies of marine aggregates are present close to urban markets or sites of future mega-projects such as oil field developments. This paper, which is based upon a review of literature and consultation with members of the Department of Energy, Mines and Resources' Coordinating Committee on Ocean Mining (DCOM), is the first step in assessing the Canadian offshore f or its resource potential with respect to quantified deposits, known and speculative mineral occurrences. Although this is a subjective evaluation, the potential appears promising. A more detailed resource inventory is required to provide a more certain assessment.

Jan 1, 1984

By T. A. Utigard, S. Pedler

Ilmenite from the Everett deposit in Quebec was characterized both chemically and mineralogically. The sample investigated contained the following main components: 40% Fe2O3, 21% TiO2 and 21% SiO2. The ilmenite grains contained about 20 to 25% hematite intergrown blades, with widths ranging from 2 to 30 \u03bcm. Crushing the sample to less than 0.85 mm led to significant liberation of the ilmenite from the gangue minerals. Gravity separation followed by magnetic separation of this size fraction led to a TiO2 concentrate grading of about 30% TiO2, with a recovery of 94%.

Jan 1, 2010

By K. B. Chaudhurl

The thermodynamics of the reactions taking place are examined with the aid of equilibrium diagrams for the Pb-O-S system. Based on investigations of chemical, mineralogical and differential-thermo analyses of intermediate products of different desulphuration degrees, an attempt is made to explain the mechanisms of the reactions in the smelting shaft of the KIVCET furnace. The differences between this and other direct lead smelting processes are demonstrated by these thermodynamic and kinetic considerations. Proceeding from these results, the practicability of direct lead smelting processes is discussed with reference to the composition of the primary feed materials to be processed. This comparison also considers the behaviour of minor metals, the products obtained and their characteristics in respect to further treatment. For assessing the operating costs, the over-all energy consumption is considered taking into account various price relations between electric energy and fuels/reductants. Based on the peculiarities of the various processes, an attempt is made to compare the necessary means of meeting the pollution control requirements. The paper concludes with reference to the criteria and problems involved in comparable evaluations.

Jan 1, 1978

By A. Bascetin

The mining industry in Turkey has been developing in the last 10 years. Mine wastes and tailings have thus been increasing, depending on the rising production rates. There are many problems related to accidents that occur in tailings damps. In this study, the applicability of the surface paste disposal (SPD) method for a Pb-Zn mine in western Turkey was examined. Density was 3.084 and specific surface area was 0.899 m2/g. The mill tailings have very low plasticity and show characteristics of clays and silts in terms of the Unified Soil Classification System. The particle size distribution of the tailings was 39.2% particles finer than 20 µm. The results of this study showed that the physical and chemical properties of mill tailings make them suitable for SPD.

Aug 1, 2013

By F. Awotwe-Appiah, P. Koshy, A. Y. Fosu, J. Dankwah, J. R. Dankwah

Ghana currently exports its bauxite raw without any value addition. Gradual depletion of high grade bauxite (with high alumina content) and the emergence of low grade bauxite (with high iron oxide content) calls for novel and inexpensive ways to recover alumina from these low grade ores. Bauxite users have indicated their willingness to pay 10% to 50% higher for a corresponding reduction in impurities by a similar amount. This project therefore investigates the carbothermal upgrading of the Ghana Awaso bauxite using waste polypropylene as reductant in a locally designed gas-fired furnace. Composite pellets of low grade bauxite sample (assaying 45% Al2O3) containing pulverised waste polypropylene were formed, oven dried, placed in fireclay crucible and fired for 30 minutes. The magnetic fraction after reduction was separated by a Low Intensity Magnet and weighed. It was observed that up to 97% of the iron oxides (occurring as hematite and goethite) could be separated into the magnetic fraction as magnetite leaving a nonmagnetic fraction with over 98% Al2O3 as opposed to the 45% Al2O3 in the as-received bauxite sample. This research direction provides yet another simple but effective way for simultaneously upgrading low grade bauxite and recycling waste polypropylene, whilst at the same time decreasing the amount of waste material generated as red mud after the Bayer process.

Jan 1, 2015

By Ralph W. Edie

"IntroductionTHE GOLDFIELDS AREA in northern Saskatchewan has be-come important in recent years because of numerous discoveries of pitchblende. The area is underlain by rocks of Precambrian age and, because of metamorphism and hydrothermal alteration, the geology in the vicinity of the pitchblende deposits is exceedingly complex and presents a challenge to all geologists •working in the district. This paper is a contribution to the geological literature of the area and presents a description of rock types, supplemented with petrographic, chemical, and spectrochemical data.Field work in connection with this paper was carried out during the summers of 1948, 1949, and 1950 while the writer was employed as assistant geologist for the Crown Corporation, Eldorado Mining and Refining ( 1944), Limited, Gold-fields area. Laboratory work was undertaken at the Massachusetts Institute of Technology during the winter months of 1949-50 and 1950-51 and extended through the summer of 1951.With the exception of SiO2and FeO, all of the new analyses ( 1) presented were carried out by quantitative spectrographic techniques under the supervision of Dr. L. H. Ahrens at M.I.T. Many of the techniques have only recently been developed at that Institute and detailed laboratory procedures have not yet been published."

Jan 1, 1952

By T. G. Joseph, A. Chamanara

ABSTRACT: The chicken and egg scenario — where adverse truck motions cause ground deterioration and poor ground profiles cause adverse truck motions — is a downward deterioration spiral dominating our industry. If we remove one action, the reaction stops. A simple truck to excavator load data analysis and wireless communication system is outlined, which will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. This will reduce subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life, and ongoing maintenance of haul roads.

Jan 1, 2012

By H. Marquis

The present paper consists of a survey of the literature on the problems of abrasion and wear of metals and materials by suspended matter. This problem is a very general one in industry, and is especially notice-able in the operation of cyclones and other types of dust collectors. The problem of abrasive dust in corrosive gas environments, such as commonly encountered in metallurgical industries, is particularly severe. Very little work has been done in the study of this type of abrasive wear, especially at high temperatures. However, a general review is presented here of all the work published on related subjects, such as that involving sand erosion in turbines and water wheels and the effect of temperature on friction wear. Topics in this paper include: blasting wear by sand, quartz, limestone, silicon carbide and other refractory particles; methods of investigation; effects of velocity, temperature and *Canadian Armament Research and Development Establishment, Valcarter, P.Q. angle of attack; correlation between indentation hardness, scratch hard-ness and resistance to abrasion; the effect of protective coatings; resistance of various metals; etc.

Jan 1, 1962

By J. Beddoes

Many high strength aerospace alloys undergo solution heat treatment (SHT) and aging to develop precipitate strengthening. Most simply, SHT involves an isothermal hold in a single phase region followed by relatively rapid cooling to develop a super-saturated solid solution from which precipitates form during aging. However, subsequent properties are sensitively dependent on the details of the SHT, which frequently also serves a homogenization function. Altering the details of the thermal cycle during SHT significantly improves the properties attained during aging, as presented by examples of SHT design for titanium aluminide intermetallics, polycrystalline and single crystal superalloys, and 7075 aluminum.

Jan 1, 2010

By C. Doyle, D. M. Hoffman, C. Díaz, J. Hrepic, W. J. Koshut, R. H. Hanewald

"Recently, lining life of the INMETCO submerged arc furnace has been dramatically extended from an average of eleven months in the 1980s to a current record of 34 months. This paper summarizes test work and operating results describing the development and establishment of slag parameters that reduce corrosion of the magnesite-chrome refractory lining.The desired slag parameters are now maintained by utilizing waste streams as slag additives. This paper also discusses the successful evaluation of a rebonded-fused-grain magnesite- chrome refractory as a lower cost, more thermo-mechanically forgiving alternative to a fused-cast magnesite-chrome refractory that had been the refractory of choice in previous years at INMETCO.IntroductionSince 1978, INMETCO, a wholly owned subsidiary of INCO Limited, has been well known for recycling by-products from the production of stainless steel, namely, EAF bag- house dust, mill scale and grinding swarf. INMETCO operates the only smelter in North America dedicated to the recovery of nickel, chromium, and iron from hazardous and nonhazardous waste. The process was developed in the research laboratories of INCO. In recent years, the process has been successfully modified to accept a wider variety of other specialty steel waste streams including: spent pickling solutions, pickling and waste water treatment filter cakes, acid scale, carbon brick, spent bag-house bags, torch cutter dust, spent dolomitic and chromium-bearing refractories, and rechargeable nickel-cadmium batteries."

Jan 1, 1997

By E. E. Cudby

"FOLLOWING the Leduc discovery •by Imperial Oil in 1947, The California Standard Company began to acquire land in the area immediately west of Edmonton and in line with the Leduc reef trend (Figure 1).The California Standard Winter-burn Province No. 1 in Lsd. 10, Section 4, Township 53, Range 25, West 4th, which was spudded, on the basis of a seismic anomaly, in December, 1949, failed to find reef. This well was located on the eastern .edge of a large land block which California Standard and Imperial Oil had pooled as a joint venture, with California Standard a:s the operator (Figure 2).The culmination •of an extensive exploration and land aquisition programme was the drilling of the California Standard-Acheson Province No. 1 well .in Lsd. 13, Section 2, Township 53, Range 26, West 4th. On August 24th, 1950, a drill stem test was run in the D-3 zone which had been encountered at 4,969 feet, and a flow rate of 702 barrels per day •of 36° gravity oil was obtained. Just previously, Imperial Oil had completed a similar programme in the Stony Plain Reserve with the swabbing-in of Imperial Stony Plain No. 1. These two discoveries set off a drilling programme to determine the extent and value of the oil accumulation.Subsequent drilling of wells some successful .and others not by several other companies as well as California Standard bias, .to date, still left much to be determined as to the approximate delineation of the productive limits of the Ache-son-Stony Plain area. However, to August 31st, 1951, there were twenty-one D-3 producers north of the reserve and three in the Stony Plain Reserve."

Jan 1, 1952

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016