Search Documents

By Michel Robert

"In 1974, Copperfields Mining Corporation and Soquem formed a new company, Niobec Inc, to bring the niobium deposit of the St-Honore carbonatite into production.St-Honore is located in the Saguenay area, near the cities of Chicoutimi and Arvida, and about one hundred and forty (140) miles north of Quebec. The discovery of the carbonatite complex was made in the fall of 1967 as a result of an airborne radiometric survey in search of uranium. The detailed exploration of the carbonatite indicated two niobium-bearing formations besides the original discovery of a rare earths zone. During the following years, the niobium formations were defined by diamond drilling and a decline was driven down to obtain adequate samples for metallurgical evaluation. In 1974, after seven hundred (700) bench scale tests, eleven (11) months of pilot plant 2nd a worldwide market research, a joint decision was made to initiate the development of a fifteen hundred (1500) T.P.D. mine and mill, under the management of Teck Corporation. The construction of the facilities were completed in early 1976 both on time and within budget. Niobec is now the only north american and the world second largest producer of Niobium concentrate.The process used at Niobec was developed from the pilot plant programs and later modified by the mill personnel. A simplified flowsheet for this process is shown on the slide. Briefly, run of mine ore is crushed to minus 5/8"" and fed to a rod mill, ball mill, and screens circuit where the ore is ground to 92% passing 65 mesh. The ore is deslimed in two stages of cycloning, and the final cyclone overflow at 85% minus 11 microns goes to waste. The cyclone underflow is conditioned prior to flotation of a carbonate-apatite concentrate. This concentrate is cleaned twice and then pumped to tails. The carbonate rougher and cleaner tails are cycloned in two stages to change the process; water and then sent to the pyrochlore rougher flotation. The rougher concentrate is cleaned five times. This is followed by pyrite flotation to remove sulfur, leaching with hydrochloric acid to remove phosphorus and dyed to less than 0.1% moisture before being sent to packaging."

Jan 1, 1978

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997

By Bern Klein

Motivation for Improved Energy Efficiency in Mining ? Canada potentially adopting Greenhouse Gas Emissions and Intensity Legislation in 2013 ? BC -Climate Action Plan and Energy Conservation Agreement in 2008 ? BC Energy Plan 2007 -BC Hydro is mandated to save 50% of new load growth ? TSM Initiative -Energy Management, Energy Reporting, Setting Energy Targets, GHG Management BC MOU for Energy Conservation Agreement -MEMPR, MABC, BC Hydro

May 1, 2010

"Increasing demand for timely and accurate information about flotation plant performance requires metal accountants to increase the scope and reporting frequency of plant production. This trend has brought in-process inventory estimation at the forefront of metal accounting issues. Such significant in-process inventories can be locked in diverse process equipment (bins, holding tanks, flotation cells, thickeners, pipeline, etc.) or in stockpiles (ore, concentrates, tailings, etc.). Practice has shown that boldly ignoring these in-process inventories or the errors associated with their estimation lead to unreliable metal balances thereby creating confusion in plant production planning and operational performance assessment. To this extent, the characteristics (physical bounds, spatial heterogeneity and residence time) as well as the available measurements (volume, density, humidity, mass, composition, etc.) of each unit/section found in a generic flotation plant are jointly reviewed with respect to the particular metal accounting issues they present. The daily and monthly metal accounting tasks are then reviewed together with possible methods for obtaining reliable inventory estimates including different procedures for end-of month reconciliation.INTRODUCTION Most of the cost reduction initiatives of the mining industry aim at improving capital efficiency and asset utilization. Among the possible paths through which these goals can be achieved are mine-to-metal optimization, real-time plantwide process control (Hodouin, 2011) and knowledge sharing databases (Bascur & Linares, 2006). However, the successful implementation and subsequent monitoring will ineluctably results in an increased demand for timely and accurate information. This more than often requires metal accountants to increase the scope and reporting frequency of plant metal production. A striking example of such scope expansion is the Minas-Rio iron ore project in Brazil (Anglo American, 2013) having a pipeline route of 525 km between the concentrator and the concentrate shipping area. Several other mining companies have also set an increased frequency for their key performance indicators thereby shrinking the metal accounting period from monthly to weekly and daily. Those concurrent trends have brought in-process inventory estimation at the forefront of metal accounting issues. Indeed, as illustrated in Figure 1, improving trading reactivity requires improvements in production planning which strongly impacts the requirements for reliable metallurgical accounting. Furthermore, practice has shown that boldly ignoring significant in-process inventories or the errors associated with their estimation can lead to unreliable metal balances. In other words, since metal balances are the cornerstones of metal accounting, some of the risks associated with important business decisions are linked to errors associated with in-process inventory measurements."

Jan 1, 2014

By Buse Florian

This paper presents the specific features of the large-scale production and transportation systems (LSPTS), describing the main notions and characteristics of the LSPTS elements. A methodologically unitary approach of the formulation, formalization and solution of the problems regarding the planning of the LSPTS structure development is offered, based on the system description by the aggregation-decomposition method, as weil as on the complex of interreloted models for the planning optimization. The paper describes the characteristics of the complex of dynamic models for investments, utilized in solving the planning problems of the LSPTS structure development.

Oct 1, 2009

By T. Binnert Haites

INTRODUCTION NUMEROUS examples of troubled zones, interfering with the normal development of coal seams, have been cited in the literature. From a geological point of view they can be subdivided into structural and sedimentary troubles. Of the latter type, wash-outs are usually the most bothersome. Some years ago, A. A. Thiadens and the author arrived at the conclusion that they represent fossil river-beds. A method of predicting the course of these rivers was developed, which has been successfully applied in the Netherlands coal measures, and more recently by P. Stassen in some of the Belgian coalfields and by the author in the Sydney coalfield. The Sydney coalfield has long .drawn the attention of geologists, and three main periods of systematic geological research may be distinguished. The first period, 1872-1900, is covered by the studies of Ch. Robb and H. Fletcher (32, 10-13) (1). Their detailed sections of the cliffs have lost nothing in value, and are frequently consulted today.

Jan 1, 1951

By Todd Smith, Brigitte Lacouture, Greg Anderson, David Lin

"The lead and zinc flotation circuits at Red Dog Mine are preceded by a preflotation circuit which recovers naturally-floating organic carbon contained in the ore. Organic carbon is a potential contaminant in the lead concentrate and is detrimental to lead-zinc selectivity. Prior to 2007, the Red Dog preflotation circuit consisted of a single stage bank of tank cells which floated the organic carbon. The preflotation concentrate was discarded directly to tailings, however, this stream contained significant amounts of lead and zinc. Zinc loss to preflotation ranged from 2% to 6%, relative to the zinc in the mill feed and was proportional to the amount of organic carbon in the ore. The main mechanism of the zinc loss was entrainment.Pilot plant and modeling testwork were conducted to examine the use of a Jameson Cell to clean the preflotation concentrate. Results indicated that up to 90% of the zinc deporting to preflotation concentrate could be returned to the flotation circuit for recovery. The installation of a 5.4 m Ø Jameson Cell with 18 downcomers was initiated in June 2006. The new preflotation cleaning circuit was commissioned in March 2007. Conservatively, preflotation cleaning has resulted in zinc and lead absolute recovery gains of 1.0% and 1.5%, respectively. The $9.1M project has a payback period of approximately 1 year at current metal prices.INTRODUCTIONRed Dog Preflotation CircuitRed Dog Mine is located above the Arctic Circle in northwest Alaska. It is the world’s largest zinc concentrate producer with a production rate of more than 1.0M t/yr. Red Dog is operated by Teck Cominco Alaska Incorporated under an operating agreement with the Northwest Alaska Native Association (NANA). Due to the remote location of the mine, it is accessible only by air, or seasonally, by ocean-going barges.The Red Dog deposit is a rich sedimentary exhalative (sedex) zinc-lead-silver deposit. The major sulphides, in decreasing order of abundance, are sphalerite, pyrite, galena and marcasite. Due to the complex nature of the ore body, run-of-mine ore is blended in stockpiles before being crushed and processed through the concentrator. The average mill feed grade for 2006 was 6.1% lead, 20.6% zinc, 8.0% iron and 0.67 % organic carbon."

Jan 1, 2008

By B. Roy

The Somita plant processes low sulphide gold ore in Burkina Faso with a CIL process. After experiencing recurrent low gold recoveries, Somita undertook an investigation on the source of the problem. COREM conducted a mineralogical study on different pit samples. A series of tests was also conducted on a composite sample from the plant which shows a content of 3.4 g/t in gold and 0.48 % in graphite. A reference test in laboratory resulted in a recovery of gold of 75%, similar to plant recoveries for the evaluated ore. In these tests, even if cyanide is not deficient, it was diverted mainly into iron cyanide complex, copper cyanide complexes and by graphite adsorption. Causes of low recovery were also identified and quantified. Solutions to increase gold recovery were suggested such as increasing gold dissolution kinetics by O2 or by lead nitrate addition, change in activated carbon addition point location to the 1st cyanidation tank and finer grinding to increase liberation. Increase in the pH could also contribute to reduce cyanidation consumption. Following these recommendations, Somita changed carbon addition from tank 2 to tank 1 in the CIL circuit. This change led to an increase of more than 5% in gold recovery. A system for the addition of lead nitrate is also under implementation at the plant and benefit will be evaluated in 2013. Finally, pit management for cyanidation will be done based on mineralogy instead of gold content in the future.

Jan 1, 2014

By H. R. Butler, R. N. Browne

"The International Nickel Company of Canada Limited consumes some 33 ½ millions of gallons of fresh water and reuses more than 100 millions of gallons of water daily. The continuing search for suitable recycle methodology has enabled the Company to put one 25,000 TPD mill on line utilizing recycled water entirely and a second 35,000 TPD mill is under construction which will likewise employ the concept of recycled water. Future milling plans are aimed at the replacement of all fresh water with recycled water, including sewage effluent and mine waste water.WATER REUSE AT INCO’s SUDBURY MILLSAs man searches unexplored horizons for new and economic industry, he must be constantly and acutely aware of the presence or absence of that precious commodity without which Industry, indeed Man himself, could not survive -- W A T E R. The water requirements of the world today are magnanimous, considering that in 1960 the estimated consumption in the United States was over 300 billion GPD (l) or more than 1,700 GPD per person(5) The magnitude of the problem can be visualized as one considers that three times this quantity of water will be required in the United States by the year 2000, when the dependable supplies of water are estimated to be only two-thirds of that required(2). How, then can we continue to wreak such havoc on that life-sustaining substance - WATER?"

Jan 1, 1970

By Robert Martin

New Millennium ?a new project for an experienced mine building team ?Owns 100% of KeMag(Harris Lake) property ?Owns 80% of LabMag(Howells River) property -20% owned by Naskapi Nations of Kawawachikamah ?All founding directors are mining professionals : Geologists or Mining Engineers ?All have extensive experience in the iron ore industry ?The Project Office is located in Montreal, lead by a team of experienced iron-ore professionals Project Overview Geology & Resources Market Prospects Process & Product Development Development Plan Questions

May 1, 2007

By J. R. Porter, C. Panaou

"A significant effort is expended on preparation of the capital estimate for feasibility studies. The development of the operating cost estimate is usually allocated a significantly smaller budget and less emphasis is placed on ensuring the accuracy of the operating cost. This paper presents a comparison of capital and operating costs of hydrometallurgy processing plants in order to demonstrate the importance that variations in operating costs have on the overall life-of-mine costs. The analysis is supported by a case study on the operating costs of a water treatment plant at an existing Australian hydrometallurgy facility at the feasibility design level. INTRODUCTIONDetermination of the economic validity of a minerals processing project is a critical outcome of a feasibility study. In many cases, the financial results of the feasibility study will determine if the project should proceed to execution. Ensuring that these results are reliable and built upon sound engineering practices allows companies to make informed decisions on resource opportunities and the selected technology.The methodology for developing a capital cost estimate at the feasibility level is well established. Specialist engineering estimators use budget quotations, first principle estimation and rules-of-thumb to develop an estimate with an accuracy of typically -10% to +15%. Cost reporting software packages are used to methodically build up the estimate from design information supplied by the engineering disciplines. Risk analysis and capital expense workshops are carried out to identify potential deficiencies in the estimate. It is widely recognized that in order to successfully produce a feasibility level capital estimate with an appropriate level of accuracy, a rigorous development process is necessary.The development of the operating cost estimate is typically less rigorous than the capital cost estimate. The operating cost is normally derived by the process engineering discipline and rarely are specialist estimators used to support the development. The allocated budget for producing an operating cost is usually smaller and less emphasis is placed on ensuring the accuracy and contingency reflect the most likely operating cost scenario."

Jan 1, 2012

By Hongfei Li, JianLong Wang

This paper introduces the technical characteristics, transformation scheme and production practice of the project in which Copper P-S Converter was replaced by Bottom Blowing Continuous converting for the first time, and introduces the technical achievements obtained by the project. The application practice proves that bottom blowing copper continuous converting technology can completely solve the problems of fugitive off-gas pollution in the ladle transportation, large amount of flue gas and fluctuation of flue gas caused by P-S converting. Comprehensive energy consumption and operating costs of producing blister copper, safety and environmental risks are greatly reduced, and economic, environmental and social benefits are significant. It is one of the preferred technologies for upgrade and to replace P-S converting technology. INTRODUCTION At present, more than 80% of copper production capacity is still using the P-S converting technology with a history of more than 100 years. During P-S converting process, melted copper matte needs to be transported by ladle, and it needs to rotate the furnace body several times, causing a lot of serious environmental and safety risks such as SO2 flue gas emission and low-altitude SO2 pollution. In addition, the high operating cost caused by low rate of air blowing, the short life of the refractory materials and high energy consumption during P-S converting become big problems. Other problems such as large amount of flue gas, low SO2 concentration, large fluctuation of flue gas volume and SO2 concentration, and discontinuous flue gas cause high cost of subsequent flue gas treatment are also needing to be solved. In order to solve these problems during the P-S converting, metallurgical engineer in various countries has spared a lot of efforts to develop continuous blowing process for decades. The continuous converting that have been industrially applied are flash continuous converting, Mitsubishi continuous converting, Noranda continuous converting, Bottom Blowing Continuous converting and multi-lance top blowing continuous converting

Jan 1, 2019

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

By Colin Hardie, Erik Bartsch, Guy Comeau

"The Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik region has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,200,000 tonnes per year due to an Optimization Project (FAG to SAG conversion) in 2005 and many recent processimprovements.In 2006, the Raglan Metallurgical Group with assistance from the Xstrata Process Support group decided to make SAG control one of its priorities in order to further increase throughput and improve stability. The original primary mill control logic delivered by the Optimisation Project in 2005 consisted of a simple PID loop controlling the mill charge (bearing pressure) through feed rate changes. Due to the multivariable, non-linear and disturbance dominated nature of the SAG circuit it was quickly found that this traditional PID control strategy was not able to adequately control the mill; resulting in poor stability, frequent operator interventions and less than optimum performance.This paper describes the successful integration of advanced field systems such as mill feed image analysis (Wipfrag) and crusher gap controller (ASRi), into a multi-variable fuzzy logic SAG mill controller. The process of how a strategy for control was developed and implemented directly in the existing control system (exploiting standard system capabilities) is discussed. It is also shown how this approach has provided mill automation which is simple, robust (despite erratic feed characteristics), and delivers both an increase in throughput and a reduction of variability.INTRODUCTIONOriginally commissioned as a Fully Autogenous Grinding (FAG) circuit in 1997, preparations to convert the Katinniq Concentrator Mill to SAG had in fact commenced as early as 1999, but were halted owing to alternative process improvements which achieved up to 1Mtpa as early as 2000. Up until this time, plant process controls had remained more or less static; modifications having been limited to those required by new equipment. Primary mill process controls and related measurements were at this stage limited to:"

Jan 1, 2008

By Adil Aledresse, Louis Mercier, Laxman Amaratunga

"The development of high capacity adsorbents with uniform porosity denoted, MP-HMS (Mercaptopropyl – Hexagonal Mesoporous Structure) using nanotechnology, and their ability to extract gold from solution, is presented. The preparation of highly effective heavy metal ion adsorbents by the incorporation of thiol moieties into the pore channels of mesoporous silica molecular sieves has been the subject of many nanotechnology research investigations. The unique feature of these nanoporous adsorbents is their ability to adsorb gold ions from ultra-low concentration solutions like mine effluent as well as from leached solutions in gold mills. The preliminary studies from laboratory simulated gold solutions show that the adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 370 mg gold per one gram of the nanomaterials from Tetrachloroaurate solution (up to 37% of their weight). Experimental studies indicated that the maximum adsorption of gold (as high as 99.9% recovery). The current studies will be extended to investigate the interaction of ionic gold complexes with nanomaterials. Future development of this work may lead to either to replace the conventional CIP/CIL processes or use nanomaterials in tandem with the former, suggesting plausible use of mesoporous material in pulp, MIP or in leach, MIL, as a novel gold extraction process.INTRODUCTIONGold typically occurs at very low concentrations in ores less than 10 g/t or 0.001% (mass basis). At these concentrations the use of aqueous chemical (hydrometallurgical) extraction processes is the only economically viable method of extracting the gold from the ore. Typical hydrometallurgical gold recovery involves a leaching step followed by the separation of the gold bearing solution from the residues, or adsorption of the gold onto activated carbon adsorbent. After elution from the activated carbon the gold is further concentrated by precipitation or electrodeposition."

Jan 1, 2008

By Jim Dodd, Jim Paynter

"We would like to acknowledge the efforts of the following key people who helped to make this project a success.Ron Jung, instrumentation supervisor for the Golden Giant Mine, spent many hours reviewing process and instrument drawings, selecting instruments and providing hands on support during commissioning.Andy Keough, underground production supervisor for the Golden Giant Mine, was responsible for readying the underground distribution network for paste backfill.H.A. Simons Ltd. personnel who did an excellent job providing sound conceptual and detailed engineering.Fred Brackebusch, of Mine System Design who designed the paste backfill delivery systemPierre Lacombe, mill superintendent of the Louvicourt Mine, generously shared information and operating experience of their paste backfill plant.AbstractThroughout the 11 year history of the Golden Giant Mine, the primary backfilling method made use of consolidated rock fill. New backfill technologies have developed over recent years which now make it possible to use large quantities of fine mill tailings as backfill.In January of 1996, construction began on a new paste backfill plant at the Golden Giant Mine. Six months following, the plant was commissioned. This paper describes the design, commissioning and operational experience to date of the paste backfill plant."

Jan 1, 1997

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By J. L. Bowlby

The heats of combustion of fuels are determined in the laboratory by means of a calorimeter, usually of the oxygen bomb type. A known weight of the fuel is burned in an atmosphere of oxygen under approximately 400 pounds pressure in a heavy metal container-the bomb- and the heat evolved is imparted to a definite quantity of water. From the rise in temperature, measured by means of a Beckmann thermometer, and other data incidental to the determination, the heat value of the sample can be calculated. On paper, the method appears simple indeed, but in practice the determination of the heat of combustion is one of the most difficult of the various coal analyses. This h as led to considerable investigational work in order to obtain formula: whereby calorific values of solid fuels could be calculated from proximate analysis data al one. The proximate analysis of a fuel consists of the determination of moisture, ash, and volatile matter, with fixed carbon by difference. Sulphur determinations properly belong to the ultimate analysis, but in this section of the country, where the sulphur content of the coal is comparatively high, a request for the proximate analysis of a fuel implies the determination of the sulphur as well.

Jan 1, 1929

By D. Hatfield

"Flotation plants typically aim to maximise recovery at or above a target grade. As the ore from the mine varies, operators increase or decrease the mass pull in different flotation banks by adjusting air and level set points in order to achieve target concentrate grade. A methodology has been developed to maximise overall recovery at target grade by determining the optimal mass pull for each bank. However, the approach of targeting equal grade for each ore type in the deposit leads to sub-optimal overall recovery. This is because some ore types sacrifice a large amount of recovery to reach target grade while others easily achieve target grade and can be processed at higher than target grade for little or no loss in recovery. Processing different ore types at different grades and blending the concentrates therefore gives a higher overall recovery.This paper presents a case study where an 80 year production forecast was made for a large Chilean copper concentrator in feasibility stage. A circuit model was created using SGS’s Integrated Geometallurgical Simulator (IGS) for the different ore types to be processed. The model was calibrated from standard rougher flotation tests (MFT), cleaner tests and from the results of plant surveys of similar operations. The pull rates for each bank in the circuit were determined to achieve an optimal graderecovery curve for each ore type. These curves were combined at different concentrate grades for each ore type to obtain the mathematically optimal overall recovery at target grade. The paper shows a methodology for obtaining an optimal combination of operating conditions for each ore type to maximise overall recovery at a set combined concentrate grade."

Jan 1, 2013

By R. Nendick

"IntroductionThe Ancient Egyptians recovered gold from the mud in the bottom of ponds by having teams of maidens sit around the pond dipping goose feathers dipped in grease into the mud. The gold would preferentially stick to the oily surface and was periodically washed off to give a gold concentrate. This was a forerunner of today's flotation processes.In Greek mythology Jason and the Argonauts pursued the Golden Fleece, which was a primitive form of gravity concentrate produced when gold ore slurry was passed over a sheeps fleece. The heavy gold settled and was caught in the fleece, producing a rich concentrate that allowed Jason & Company to perform the first recorded case of highgrading. The process was a forerunner of todays shuiceboxes used in placer mining.From these simple beginnings, gold metallurgy has progressed to a state where very complex flowsheets are proposed, sometimes to perform a simple metallurgical task. Figure (i) shows a hypothetical flowsheet to identify the range of unit processes that might be brought to bear on a refractory ore. The flowsheet identifies the three primary areas of gold metallurgical operations:Ore PreparationExtractionRecovery."

Jan 1, 1986