Search Documents

By Messenger A. J, Miles J. G

A thermal neutron irradiation technique using a mCf neutron source has been developed and applied to thp.simultaneous determination of iron and aluminium (expressed as AI2O3) in iron ore fines (-6 mm particle size) on a moving rubber conveyor belt.While the determination of iron with this technique is based on the use of a NaI(TI) detector to monitor the characteristic prompt gamma rays (7.64 MeV) emitted by thermal neutron capture reactions in the iron, the etermination of AI2O3 is based on the use of a second Nal(Tl) detector to monitor the characteristic gamma rays (1.78 MeV) emitted after thermal neutron activation of the aluminium. The second detector is located downstream from the first. Although the speed of the conveyor belt has no direct effect on the iron measurements, it must not exceed about 3 m/min if good accuracy is required for the AI2O3 measurements. Consequently an auxiliary conveyor belt is required in order to avoid interference with normal ore processing.Dynamic trials of the technique, using 1500 kg samples of ore on a 460 mm-wide rubber conveyor belt moving at 1.7 m/min, have demonstrated that the method can achieve accuracies of 0.7% Fe and 0.1% AI2O3. At the present stage of development, it is recommended that lump ore be crushed to a particle size of 6 mm before analysis.In addition to iron and AI2O3 determinations, measurements of total moisture content and bulk density are possible. The determination of Si02 is also feasible, but a separate fast neutron source (e.g., Am-Be) and a separate gamma ray detector are required.

Jan 1, 1980

By P Holtham, K Duffy, W Valery, A Jankovic

In the face of increasing energy costs, limited water resources, more stringent legislation, and lower feed grades, the mining industry is searching for more sustainable technologies and practices. Metso Process Technology and Innovation (PTI) is undertaking a research project, ‘improving the resource and eco-efficiency of mining operations’, to help the industry meet these challenges. The project is investigating alternatives in mining and processing that reduce energy and water consumption, minimise emissions and waste, and maximise the value recovered from the deposit. The targets are to reduce energy usage by more than 30 per cent and greenhouse gas emissions by more than 50 per cent compared to current practice.Key areas of interest were identified across mining and processing operations. These were grouped into the following interrelated work areas for investigation: high intensity selective blasting, in-pit crushing and conveying, preconcentration, energy efficient comminution circuits and technologies, coarse particle flotation, and water recovery optimisation. Investigations have included reviews of industrial data, modelling, simulation, and laboratory and pilot scale trials. In some areas industrial scale trials will commence shortly. This paper discusses the investigations and key findings from the project so far; highlighting the possibilities for reducing energy consumption, water usage and carbon emissions. A particular mining process may incorporate any combination of the alternatives identified and requires tailored solutions based on a detailed understanding of the ore deposit, the process and local conditions. The focus is on improving resource efficiency; creating more value with less impact and consequently a better economic return from the available resource. Technologies exist today that can transform mining into a more efficient industry for tomorrow.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Resource efficient mining processes of tomorrow, in Proceedings Third International Future Mining Conference, pp 227–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M Ireland

Extensive use of diesel-powered mobile equipment in modern mines for materials handling, such as load-haul-dump machines, constitute a significant source of heat, exhaust gases and diesel particulate matter. Provision of sufficient quantities of fresh, cool air are required to remove such atmospheric contaminants from the environment for miners, particularly at depths where ventilation constraints and associated operating costs have an increasingly adverse impact. An alternative solution to diesel equipment to combat economic, environmental, social and health challenges, are battery electric vehicles (BEV), with the potential to expand production and substantially reduce ventilation and cooling demand, subsequently reducing operating costs. In this context, this paper focuses on the introduction of a battery electric loader to a diesel fleet at one of the deepest underground mines in Australia, the CSA Mine, a high-grade copper operation in Cobar, New South Wales. Analysis of a trial battery electric loader compared to existing diesel machines is performed with regards to infrastructure, technical and operational issues. Key benefits of battery electric vehicles over conventional diesel-powered vehicles are discussed, including lower energy consumption and greater efficiency, reduction of emissions and heat, reduced need for ventilation and lower operating costs. Challenges of introducing BEVs into an operation, along with the results from the comparative study are addressed under impacts to energy consumption, equipment selection, effects on ventilation and cooling, mine design and economic viability for future fleet implementation scenarios whilst meeting production targets.

Mar 29, 2023

Advances in Coarse Particle Recovery - Fluidised-Bed Flotation

Sep 13, 2010

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991

By K Ehrig

You are a geologist, geometallurgist, or metallurgist/process engineer and are fortunate enough to work for an organisation who asks you to design/execute a geometallurgy program. What seems like a simple request is actually not a trivial exercise. æRecipeÆ style manuals are not readily available. However, many æexpertsÆ are lurking around willing to deliver solutions which will solve all of your problems. Even though similar ore deposit styles (e.g. porphyry Cu, IOCG, Ni-laterites, calcrete hosted U, etc.) have many similar characteristics, each ore deposit is unique. Hence your geometallurgy program needs to be æfit-for-purposeÆ. This paper offers some insights gained via designing and executing geometallurgy programs from exploration through to production, and working at a mine where you are held accountable for your metallurgical performance predictors.CITATION:Ehrig, K, 2013. Geometallurgy - What do you really need to know from exploration through to production?, in Proceedings MetPlant 2013 , pp 28-33 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Moorrees C, Koh P. T, Tsambourakis G

Calcination of samples from the Savage River region of Thsmania containing varying magnesite/dolomite ratios under conditions optimized for the magnesite component, followed by carbonic acid leaching at elevated pressures, leads to leachates of varying composition. For a 3 per cent solids slurry leached at 15.5°C and 700 k Pa carbon dioxide, the leachates have magnesium concentrations in the range 0.71 - 13.2 g/litre. The corresponding magnesium extraction data are 12.5 - 86.4 per cent. The variation in leachate composition would be unacceptable in terms of continuous processing, so that a feed of "constant" composition is essential. Selective mining and physical beneficiation to remove the bulk of the dolomite do not appear to be practical. It is concluded that the most appropriate method of feed preparation is to carry out extensive blending of the magnesite/dolomite ore and the resultant calcine.

Jan 1, 1987

By S Lakemond, L I. Ku, J Vaughan

Conventional processing of poly-metallic gold containing flotation concentrates are challenging for a number of reasons. One reason is that substantial copper and zinc in the cyanide leach solution compete with gold and silver for carbon adsorption sites. In this study, metal-cyanide adsorption kinetics and equilibrium are measured on three samples of coconut derived activated carbon and one sample of synthetic carbon. Loading selectivity was confirmed to be in the order gold>silver>copper>zinc for all carbon samples. The synthetic carbon tested showed promising results in terms of loading kinetics and capacity for precious metals.CITATION:Lakemond, S, Ku, L I and Vaughan, J, 2013. Effect of carbon type on adsorption of Cu, Zn, Ag and Au from mixed cyanide solution, in Proceedings World Gold 2013 , pp 411-418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

The Beginnings of Mineral Processing Research in Canada - A Short Account

Sep 13, 2010

A study of the electrolysis of PbS in molten PbCl2 showed cathode efficiencies which increased with current density at fixed sulphide concentrations, and decreased with increasing sulphide concentration at fixed current densities. The anodically produced sulphur dissolved rapidly in the melt, the rate increasing with temperature and sulphide concentration. Experiments with diaphragm cells, made to determine the relative effects that dissolution of lead and sulphur have on the cathodic current efficiency, demonstrated that dissolution of sulphur was the major contributor to the lowering in efficiency.

Jan 1, 1973

Mineralogical analysis of a nickeliferous laterite from the Rockhampton region shows that the nickel is largely associated with the manganese wad and opaline silica. The laterite also contains an appreciable chromite content (about 12 per cent Cr2O,) although this tends to be poorly liberated.Leaching with hydrochloric or sulphuric acid, at atmospheric pressure at the boiling point is non-selective with respect to iron dissolution.The degree of dissolution increases as the acid concentration and retention time are increased; cobalt dissolution requires less aggressive conditions than does the dissolution of an equivalent amount of nickel.Leaching with sulphuric acid at elevated temperatures and pressures leads to a minimum amount of iron dissolution, is rapid, and requires a reduced acid addition rate. Nickel and cobalt recovery from the clarified leachate would be simplified because of the leach selectivity.Pressure leaching appears to be the most practical route for treating the Rockhampton laterite. The economics of processing would be made more attractive by the recovery of a chromium concentrate from the leach residue. This would typically contain about 45 per cent Cr2O, and could be used as a source of chromium chemicals.

Jan 1, 1986

Much interesting data on cemented carbides has been published over a period of years which, when classified and pieced together, gives a clear picture of this special branch of powder metallurgy. This is an attempt to present the essential information in an ordered account.THE HARD CARBIDES-THEIR PROPERTIES AND PREPARATIONThe so-called hard or refractory carbides are the carbides of a number of metals which are grouped together in the Periodic Classification. These metals are in groups IV, V and VI. They are titanium, vanadium, chromium, zirconium, niobium (columbium), molybdenum, hafnium, tantalum and tungsten. These carbides have attracted the attention of chemists because of their remarkable properties. They possess very high melting points, and are rather difficult to prepare in the pure state. Their outstanding propertyis their extreme hardness, which they share with certain other carbides, such as those of silicon and boron. In addition, these compounds possess distinctly metallic properties, such as lustre (in fused specimens) and high thermal conductivities.(l)t They are capable of forming alloys in two ways:1. With metals, particularly those of the iron group. 2. With each other (a case of solid solubility).The constitution of these substances is not that of ordinary salts, which obey the usual valency rules, but must be likened to that of certain intermetallic compounds. Actually they are "interstitial" compounds(2), that is, they are formed from the ordinary metallic lattice by the insertion of the relatively small carbon atoms in the interstices.. The energy required to fill the lattice completely is high, and this explains the difficulty often found in obtaining the exact stoicheiometric compound. Thus the carbides can have a range of composition, and can be considered as solutions of carbon in the respective metals.Physical Properties of the CarbidesThe hardness of these compounds is so great that it is difficult to compare the individual compounds on this basis. Becker(l) gives values on Moh's scale, which are not very accurate and are of no great value. Burden(3) has reproduced a diagram by Hatfield which indicates that the cemented carbides are between 1,400 and 2,000 on the Vickers diamond scale. However, the pure carbides are harder, tungsten carbide being about 2,200. Hoyt(4) describes a method of measuring hardness applicable to powdered specimenswhereby the powder is rubbed on a standard block of cemented tungsten carbide under standard conditions, and the rate of wear is determined. In...

Jan 1, 1942

By G M. Mudd

The growing popularity of platinum and platinum group metals (or PGMs, including palladium, rhodium and others) for a wide range of applications leads to some interesting issues for mining and sustainability. The uses for PGMs includes catalytic converters for air pollution control in vehicles, growing jewellery use, catalysts for various purposes (especially petroleum and chemicals processing), hydrogen fuel cells and many others. Given the growing importance of most of these PGM uses in more sustainable technologies or in making industrial processes more efficient, it is critical to understand the complex sustainability issues which surround platinum and PGMs. At present, South Africa is the dominant PGMs producer and holds about 88 per cent of estimated global resources, with important but relatively minor production and resources in Zimbabwe, Russia, Canada and the United States. Given the concentrated location of PGM resources, what are the likely trends in PGM mining with respect to environmental sustainability? That is, what are the costs in terms of energy, pollution, greenhouse gas emissions, water, land use impacts, social impacts, economic aspects associated with this globally important industry? This paper compiles and analyses a range of data on platinum-PGM mining, focusing primarily on South Africa. It synthesises a unique combination of data which relates typical production aspects such as ore grade and scale with sustainability aspects such as greenhouse, energy and water costs. The findings are critical in understanding the debate about the increasing environmental and social costs of some materials and technologies which are considered crucial for sustainable industries based on PGMs. Overall, the paper represents a valuable insight into the platinum-PGM sector, providing a range of useful data for understanding the environmental sustainability of this particular group of precious metals.

Jan 1, 2009

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By P Vasconcelos, X D. Deng

Numerous supergene manganese oxide deposits are developed inSouth China as a result of weathering of a thick sequence of Paleozoic marine Mn-bearing sedimentary rocks, consisting mainly of limestones, cherts and black shales that were intensely folded and faulted due to multiple episodes of tectonism since the late Triassic. The ore minerals are dominantly pyrolusite, cryptomelane, nsutite, lithiophorite and braunite. The supergene manganese ores contain Mn ranging from 20 to 44 wt per cent; manganese oxide deposits derived from cherts and black shales also contain recoverable levels of Co, Ni, Cu, Pb and Zn. 40Ar/39Ar dating of potassium-bearing manganese oxides reveals that extensive supergene manganese ore formation started at least in the earliest Miocene and persisted to the Present. Ages of the deposits show a close correlation to tectonic stability, with the oldest in tectonically quiescent areas and the youngest in active areas that have subjected to continuous uplift and thus significant denudation. The prolonged wet and hot climate since Oligocene and the balance between weathering and erosion, which is parameter to the tectonic stability, are the ultimate controls on the formation and distribution of South China supergene manganese oxide deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The following brief observations on the mineral composition of the Mt. Oxide copper ore are intended to supplement the geological description of that ore-body recently published by Blanchard (2).'" The Mt. Oxide copper mine is situated about 45 miles W.N.W. of Dobbyn, in the Cloncurry district of Queensland (Fig. 1). A representative suite of specimens from the mine was obtained through the kindness of Mr. P. B. Nye, Executive Officer of the Aerial, Geological and Geophysical Survey of Northern Australia, and Mr. Jack Hall, the tributor of the Mt. Oxide mine. The specimens, as shown in Fig. 2, were nearly all from the sulphide zone, between the l04-ft. level and the 300-ft. level. Several additional specimens, together with information which will be referred to later were kindly sent to me by Mr. Roland Blanchard.MINERAL COMPOSITION OF THE COPPER OREThe mineral composition of the ore is relatively simple. It consists essentially of chalcocite, with varying, but minor figures...

Jan 1, 1940

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

Mt Waruwari, host to the Porgera underground gold mine in the Highlands of Papua New Guinea (PNG), is a prominent ridge of sediments and dioritic intrusives rising approximately 600m above the surrounding valley floor. Consequently, mining occurs in a low stress environment where structural and material considerations are foremost in the design of ground support and reinforcement. Three major rock types are encountered in the underground mine. These are locally referred to as "black sediments" (slightly indurated mudstones and clayey siltstones), "altered sediments" (derived from black sediments by thermal metamorphism), and "intrusives" of dioritic composition. The rocks are moderately to highly fractured, the black sediments being generally weak and occasionally sheared while the altered sediments and intrusives are quite strong but often brittle. Mining takes place from a series of stopes extracted by either slot and mass blast or a modified vertical crater retreat method (VCR), which are backfilled with a cemented rock fill. Ground support and reinforcement has been relatively conserv- ative to date and generally relies on pattern reinforcement of all development with cement grouted "rebar" bolts and mesh, extending to pattern cable bolting with occasional mesh in stope backs. In addition there has been considerable reinforcement of stope hangingwalls in some cases. A programme of broad scale structural mapping, monitoring with extensometers, material property testing, and stress analysis has been devised to allow optimum design of ground support and reinforcement in the future. Considerable work remains to ,omplete this task.

Jan 1, 1991

By S G. Walters

The minerals industry is facing a productivity and investment crisis. The ‘Millennium Super Cycle’ from 2003–2011 was an unprecedented period of growth and investment resulting in increased throughput and development of lower grade resources to meet demand. During the boom quantity became more important than quality with throughput the key metric. This was accompanied by a general trend of decreasing feed grades across all commodities that was offset with higher production volumes.Current industry perception is that feed grade depletion is an unavoidable consequence of ore deposit geology and mass mining technologies for increasingly mature mining operations. In typical crush-grind-float operations value recovery only takes place at ~1–200 micron particle size during flotation, ie 3–4 orders of magnitude size reduction compared to primary feed. For increasingly low-grade deposits the cost of energy and capital intensity required to process and reject low value material at micron scale drives poor productivity. An alternative is to deploy a range of coarse (~10–100 mm) separation and rejection technologies. Grade Engineering® is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans.Coarse rejection can be used on size distributions ranging from run-of-mine (ROM) to semi-autogenous grinding (SAG) discharge. Grade Engineering® is based on five rock based ‘levers’ linked to combinations of screening, sensor-based sorting and heavy media separation. These involve exploitation of preferential grade deportment to specific size fractions during breakage: differential blasting to condition grade by size at bench scale; sensor based sorting at truck and conveyor scale; and differential particle density.Grade Engineering® is being developed and implemented by a consortium of over 30 mining companies, equipment suppliers and research organisations. Emerging results from collaborative site activities demonstrate potential for generating significant value, which can reverse the trend of declining productivity due to feed grade depletion.CITATION:Walters, S G, 2017. Driving productivity by increasing feed quality through application of innovative Grade Engineering® technologies, in Proceedings Tenth International Mining Geology Conference 2017, pp 263–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Nicol S. K, Swanson A. R

The poor flotation response of many coals has in the past been attributed to such factors as differences in rank, differences in degree of oxidation, differences in petrographic composition, or slime coatings. The present work shows that while all these factors undoubtedly influence flotation, the size distribution of the feed may override these. Evidence is presented which shows how this factor can lead to substantial losses of coarse coal (>250 µm)from a coal which would normally be considered amenable to flotation. Reasons for this loss of flotation response are suggested together with means of overcoming the problem.

Jan 1, 1978