Search Documents

Introduction The mine winder is an essential element in the mining of ore in deep level mines and therefore requires a high degree of reliability to avoid interruption of production. Failure of any component on a winder may also be dangerous and expensive to repair. The larger the failure the larger the stoppage. The failure of a winder drum is the ultimate catastrophe, not only because of the cost of replacement, but also because of the lead time in procuring a new drum. Today these types of failure are not as common but many failures have occurred in the past and even today many an old winder is con- sidered for a new and often more arduous duty. As far back as the turn of the century a lot of information had been gathered to try and clear up the complexities of the multi- layering effect of coiling rope under tension onto a drum. Before comparing results obtained by various researchers the nature of the pressure distribution between rope and drum due to multi-layering will be discussed briefly.

Jan 1, 1987

By D V. Boger

The use of chemical additives to initiate such processes as particulate separation through flotation or dewatering through flocculation, is common in the mining industry. The dosing of additives is none the less poorly controlled from a process control viewpoint and it is perhaps fortuitous that over-dosing or misuse of chemicals is rarely catastrophic to the production cycle. In many cases, such events would go undetected if it were not for economic considerations. Recently, the advent of orebodies with finer mineral disseminations and the push for greater efficiencies in both production and tailing disposal have resulted in the need for greater control of the dosing and utilisation of chemical additives. The need to grind at higher pulp densities and to finer sizes and to dewater to higher solid contents are but two examples that require a more stringent understanding of the true role of additives in controlling the rheology of suspensions and the influence of additives on the surface chemistry of particles. The inter-relationship between the surface chemistry of particles and the role of additives in controlling suspension rheology is now well understood for systems in which the average particle shape in the mixture is spherical or close to spherical. Luckily, this is the case for a large number of systems in the mining industry and the true role of typical additives in these systems will be explored. Difficulties arise for suspensions containing clays or other platey or needle shaped minerals and in many cases, quite small quantities of platey minerals dominate the rheology of suspensions. The role of additives in controlling the rheology of asymmetric particle systems is more complex but the effect of the additive in changing particle alignment in solution is the key to understanding suspension behaviour. The manipulation of the rheology of asymmetric particle systems will also be explored.

Jan 1, 1998

The St George orebodies are situated within the tectonically disrupted eastern limb of the Boogardie Syncline.Highly disturbed rafts of banded chert formations occur within a sequence of felsic volcanic tuffs. The chert forms the hostrock for the gold mineralization.The gold distribution within the irregular and narrow banded chert formations is erratic and patchy. The average gold content of the two orebodies is between 3 - 4 g/t Au.Economic mining of these relative small, irregular and low grade St. George orebodies can be carried out by using a highly selective mining method.The highly selective mining method uses an excavator as the principle mining tool. Blasting, breaking and loading of the rocks is done in a different way than by using a front-end loader as with the conventional mining method. Simple, and therefore cheaper, blasting breaks the rocks and lifts them up without major displacements.

Jan 1, 1984

By Laing W. P, Neill D. M, O&apos

The Reward polymetallic massive sulphide deposit occurs 35 km south of Charters Towers, adjacent to the Highway gold deposit (Fig. 1). It is hosted within rhyolitic lavas and interlayered volcaniclastics of the Cambro-Ordovician Mt Windsor Volcanics. Reward is a "blind" deposit discovered in 1987 after a long history of exploration by various companies in the area. The main pyrite dominant massive sulphide body occurs under 100m combined thickness of Tertiary fluviatile sediments overlying deeply weathered gossanous volcanics. The exploration case-history provides a striking example of how geological and structural models can be built up almost exclusively from drill information. Four different styles and ages of mineralisation are present: 1) volcanogenic Cu+Pb+Zn+Ag+Au massive sulphides of probable syngenetic origin; 2) remobilised Cu+Au in massive pyrite of metamorphic/deformational origin; 3) supergene and 4) oxide Cu+Au mineralisation of weathering origin. The massive pyrite body, containing chalcopyrite lenses, transects the stratigraphy and is inferred to contain in excess of 5 million tonnes. Overlying the primary mineralisation a supergene chalcocite rich zone contains a measured/indicated resource of 634,231 tonnes of 6.77% Cu which includes 287,000 tonnes of 1.32 g/t Au and 18 g/t Ag. In addition a measured/inferred oxide resource of 309,000 tonnes of 5 g/t Au and 27 g/t Ag overlies the supergene zone.

Jan 1, 1989

Since 1958 there have been 16 major coal mine explosions in the U.S. claiming 323 lives. Whilst the exact cause of a number of these incidents has not been determined, the majority has involved gas ignitions in one way or another. In addition there have been fatal gas explosions in salt mines and vapor explosions in oil mines. Furthermore, many of the oil shale mines in the U.S. have proven to be gassy giving cause for concern. Compounding these problems is the fact that frictional ignition of methane in coal mines has dramatically increased over the past several years; over 100 such ignitions were reported in 1979. While, no fatalities have been attributed to frictional ignition in the U.S. since early 1978, a recent mine explosion in Nova Scotia which resulted in 11 fatalities was attributed to a frictional face ignition. Research being conducted at the Bureau of Mines is aimed at the prevention and suppression of gas explosions. Emphasis is placed on new coal cutter bits for reducing ignition frequency, machine-mounted water sprays for preventing frictional face ignitions and automatic devices for quenching incipient ignitions and fully developed gas explosions.

Jan 1, 1981

By J Vann, S Dunham, M Job

Two-dimensional (2D) estimation approaches have significant advantages over three-dimensional (3D) approaches when dealing with a narrow vein- or layer-like geometry. The main motivation for 2D estimation is that bias due to non-additivity of grade is avoided. The various aspects of 2D estimation are illustrated by use of a case study from the 1A Shoot Nickel deposit at Leinster, Western Australia. The width of the 1A mineralisation is variable, and so are the angles of drilling intersection. Consequently, the variable of interest (in this case nickel grade) is not suitable for direct kriging because it is defined on non-uniform support. However, grade can also be defined as the ratio of two variables that are suitable for direct kriging: thickness and accumulation. In the 2D approach, tonnage equates to thickness and metal equates to the product of grade and thickness, also called æaccumulationÆ. In the simplest approach we can independently krige accumulation and thickness and derive the grade by the ratio of the two resultant estimates. The thickness and accumulation variables must be in a consistent projection orientation, for example a horizontal projection in the case of steeply inclined mineralisation like 1A. Because the density is not constant across the 1A (and most other) deposits, the issue of density weighting is also discussed. The impact of the correlation between grade and length, or grade and density are important issues in implementation of 2D estimation. The circumstances under which these correlations need to be taken into account (by co-kriging) are reviewed. Finally some comments are made on the final use of the resultant 2D estimate for mine planning purposes.

Jan 1, 2003

By Dierling D. H

The paper briefly describes the mining system employed on Western Deep Levels for the past 20 years. The negative aspects which gave rise to a new mechanized method of mining are discussed. The sequence of events leading from the Mine's first attempt at trackless mining in 1980 to the present day in-stope project is presented. The original justification for this project and the in-stope trackless mining method is described in detail. The results to date are evaluated and the original rationale for going in-stope trackless mining questioned. A totally new mining philosophy for Western Deep Levels, whereby major geological disturbances are left in situ and longwalls re-established and mined using trackless mining machinery is described. The economics of this mining method are discussed. Trackless mining machinery can also be put to good use within the conventional longwalls in a new method of mining using Load Haul Dumpers (LHD) in reef drives. When the instope trackless mining project commenced in 1983, it was stated that expansion to any significant degree with diesel powered vehicles could be ruled out and electrically driven alternatives would have to be developed. This issue is discussed and the Mine's decision to expand with diesel powered vehicles explained. Finally, the extent to which trackless mining is likely to be seen in the 1990 s at Western Deep Levels is discussed.

Jan 1, 1986

By OÆGrady P

Finite element analysis is becoming a routine component of design of longwall extractions, now superseding more traditional somewhat intuitive approaches. Finite element modelling is relatively inexpensive and provides an adequate degree of similitude to give satisfactory analysis. The physical modelling of two decades ago is now largely replaced by numerical methods of which finite element is the best known. Important data for finite element work are physical properties, including creep aspects, introducing the non-linearity of stress response.Various computer packages are available and some were used to model two specific UK examples, using both linear and non-linear approaches. It appears that non-linear approaches will yield most benefit. The use of materially non-linear analysis is merited by the greater similitude it provides between model output and real mine situations.

Jan 1, 1991

Spatial continuity as described by a variogram is a reflection of the underlying mineralisation/geology. Modelling of the spatial continuity (variogram) must account for both the quantitative data (ie sample grades), on which the variogram calculations are based, and the qualitative information as provided by the geological interpretation. An understanding of the geology and the variogram interpretation tie together the sample values and allow us to go beyond the actual data (Journel, 1995). Variography makes geology transportable and allows the geological interpolations to be channelled downstream into mine planning, ultimately affecting the economic decisions surrounding a deposit. As such the process of variography and resource modelling is critical. Thus consistent expert decisions need to be made which force geologists to have a closer look at the available information and the geological interpretations. The aim of this paper is to provide an overview of the latest developments in visualising variography and to demonstrate their usefulness in decisions regarding the spatial continuity of mineralisation. New ideas concerning potential future developments in visualising and modelling spatial continuity through variography are introduced.

Jan 1, 1996

By V N. Rudashevsky, N S. Rudashevsky

Characterisation of platinum-group element (PGE) deposits and their process products has many challenges for the process or applied mineralogist. It is now well established that the PGE distribution for such samples is variably divided between submicroscopic concentrations of PGE in sulfides, tellurides and related minerals occurring as discrete platinum-group minerals (PGM), of which there are a large number of species, many with partial replacement between the PGE and between anions. Each PGE deposit type requires a targeted approach but fundamentally, there are two general methodologies in vogue. One way is to make a large number of polished or polished thin sections for detailed scanning electron microscopy (SEM)/optical examination to determine the PGM distribution and their associations and grain sizes. The other is to make concentrates of representative crushed or processed samples, thus having fewer subsamples to examine. Our method of choice is to use hydroseparation (HS) for concentration. HS provides representative concentrates of sizes down to ~10 ¦m, not possible by other techniques. Various microbeam methods have been used for analysis of trace quantities of PGE (EPMA, micro-PIXE, SIMS and LAM-ICPMS). We prefer LAM-ICPMS (laser ablation microprobe û inductively coupled mass spectrometry) because of the relatively large analytical volume sampled, the ability to measure all the PGE, monitor up to 20 elements, together with detection levels in the tens to a few hundreds of ppb. We provide typical results derived in studies of stratiform PGE ores and tailings, and a massive Ni-Cu sulfide ore.

Jan 1, 2008

By C Torrisi, J Andreatidis, M Duffy

BHPÆs Cannington process plant was commissioned in October 1997. The Cannington ore contains high grades of silver, lead and zinc but also contains high levels of fluorine which must be removed to produce a marketable concentrate. As a consequence the plant is more complex than the typical base metal concentrator. Some of the features of the Cannington operation include a single stage autogenous mill, multiple stages of flotation cleaning, two leach circuits, pressure filtration and a paste fill plant. The start-up and achievement of design performance for new lead/zinc operations has traditionally taken much longer than for gold or copper operation and is littered with many tales of woe with feasibility targets often not achieved (Agarwal, Brown and Katrak, 1984; Bulatovic and Wyslouzil, 1999; Leung, Andreatidis, Woodall and Alford, 1996; Sherman, 1999; Ward, 1998).

Jan 1, 2000

By S Pigram, G J. Jameson

This paper is concerned with the tracking of particles in the froth phase of an aerated water/glycerol mixture. Experiments have been carried out in a specially designed laboratory flotation cell that allows formation of a deep froth. Phosphorescent tracer particles of various sizes were injected into the centre of a froth column where they were excited by ultraviolet lights, positioned at the back and front of the column. The motion of particles was captured on a digital camera with a green filter. The images from the digital camera were then transferred to a computer and an image analysis program was used to convert the colour intensity to the concentration of particles at each location within the froth. The tracer technique was used to determine the dispersion of hydrophilic particles and the variation of the concentration of solids with axial and radial positions.

Jan 1, 2005

Battle Mountain Gold Company's Paj ingo Mine is the first gold mine developed by the Company in Australia. The Mine located in northern Queensland commenced operations in September 1987. The high grade epithermal orebody is selectively mined and processed through a conventional carbon in leach/carbon in pulp (CIL/CIP) plant at a rate of 200000 tonnes per annum. In 1988 it produced 61000 oz gold and 152000 oz silver. Inadequate preoperational development of non technical management and organisational functions often leads to inefficiencies that last well into the operation. The Pajingo experience in this regard is oaTple ented by those from a number of other recently commissioned small operations. A checklist is discussed to assist any future preoperational group in focussing their attention into areas that seem to be of secondary importance at the time but often have a significant impact on overall management efficiency later.

Jan 1, 1989

By T R. Stacey

South Africa has a long history of rockbursts, some 100 years. During this time much research and many developments have taken place in the country to limit the occurrence of rockbursts, and to mitigate their effects. In this paper I shall present a personal view of what I consider to be important achievements, and contributions made. Some of these are: planning of stope layouts, and the use of strike barrier pillars; recognition of energy as a key factor, the use of the energy release rate ERR as a layout planning criterion, and development of MINSIM for calculation of ERR and stope planning; sequential grid stope layouts; use of backfill for stope support; and, development yielding support elements, and dynamic testing of stope and tunnel supports. The record shows the establishment of a rock engineering research powerhouse over a 40 to 50 year period and, unfortunately, the complete breakdown of this capability in the subsequent 10 years. CITATION:Stacey, T R, 2018. A personal review of South African rockburst research, experience and lessons learnt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 5–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

The key elements required to maintain final wall integrity and hence slope reliability are discussed. Failure modes and mechanisms in highly structured rock slopes are then reviewed. The impact of blast disturbance on rock masses in general is discussed and the relationships between the slope failure mode and blast disturbance is then explored. The question of how designers can incorporate such impacts into the slope design process is then addressed. This necessarily involves rock mass strength consideration and two case studies are used to demonstrate a recent dilemma in this regard. Some progress regarding this dilemma has also been reported for the second case study. The major conclusions are that: Slope reliability can be severely compromised if the slopes are damaged by blasting and this impact is not often incorporated into the slope design process. The location and extent of the blast damage will impact some slope failure geometries and failure mechanisms more than others. The concept of failure mechanism specific vulnerability needs to be further developed. The evidence indicates that this aspect is even more extreme for weak ground conditions. The quantification of the reduction in rock mass strength due to blast damage is not well understood and limitations exist with some recent guidelines. The use of the Hoek-Brown criterion for slopes in blocky rock masses requires considerable judgement. Further applied developments in this regard would be very beneficial to the industry. Some promising methods to incorporate blast damage estimates into the slope design process are emerging. It is good business to minimise final wall blast damage otherwise a whole range of issues relating to reduced slope reliability emerge.

Jan 1, 1999

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987

By Wu Y, Qu Q

The Central Coal Mining Research Institute has developed the MAE acoustic emission monitoring system, the BD4-1 portable acoustic emission monitor and the MRB rock burst monitoring system. In the MAE system there is an IBM-PLAT, a receiver and 16 channels and the investigating range is 100 m. The main functions are detecting acoustic events from the working faces, periodically making statistics, prints, displays and storing of the results, and performing the off-line process such as drawing the curves of acoustic activity. The BD4-1 instrument has four channels, it works for more than 24 hours continuously, and keeps the data for more than 30 days after power tum-off. The BD4-1 is suited to the monitoring for a long or a short time as a fixed point where the system is invalid, especially to the monitoring of the acoustic activity promoted by the blasting. There is an IBM-PC/AT, a receiver and 16 channels spread 10 km in the system MRB. The system could on-line collect microseismic events throughout the whole mine, calculate the source location and the energy, and off-line draw the seismic activity draft of time-based or distribution in space. In practice, the forecasting is successful by using the acoustic emission and microseismic monitoring system and the portable instrument.

Jan 1, 1991

This paper details a proposal for integrating the use of the Pilbara Iron Ore Classification (PIOC) and stratigraphic data for fine tuning blast. pattern design on Mt Whaleback. The main thrust of the proposal is based on the assertion from Haqan and Harries (1979) that rock properties influence blasting results more than explosive properties. This premise is supported by a literature search, which indicated that blasthole burden, spacing, stemming and subdepth lengths are also determined by rock properties if the same explosive and blasthole diameters are used. A brief explanation of the PIOC is provided during which it is noted that the classification is based on physical hardness, mineralogical and genetic characteristics of the ore. The classification also extends to the two main waste rock types LBIF (banded iron-formation) and shale]. Ore type plans produced from face mapping indicate that many areas on Mt Whaleback can be divided into various PIOC zones and regions thus making it more useful in blast pattern design. Several recommendations for blast pattern design experimentation are made for hard, medium and soft ores as well as for the waste rocks, the most important being the use of expanded patterns to blast. soft BIF and medium hard to soft shales.

Jan 1, 1986

Diamond drilling is a relatively new commodity in terms of drilling. The first known diamond drilling activities were carried out in the Swiss Alps around 1863 when the Swiss engineer M Leschot designed and made a tube with a diamond set face which was used in probing ahead drilling for the Mont Cenis tunnel (Figure 1). Craelius AB which today is a part of the Atlas Copco Group was formed in 1886. The name Craelius is a family name and the founder of the company was Per Anton Craelius (Figure 2). He went to the United States to study this new technology using diamonds to extract core samples and when he returned to Sweden designed his first diamond drilling machine. It was a man-powered drill needing a crew of six men, two to crank the unit, one to feed, two to power the flush pump and a foreman (Figure 3). As time passed through research and development, the original design was improved and manpower was substituted for steam engines and later combustion engines or electric motors (Figure 4). During the 1930s the drills radically changed designs and took the form of the short stroke drills which to a certain extent are still in use today. The original design of these drills have been refined during the years, hydraulic chucks, gear boxes and other improvements have been added.

Jan 1, 1995

Exploration risk increases with time, due to a general decrease in prospectivity as the more accessible deposits are found, and be- cause of rising costs and demands due to an improving standard of living. Risk is separated into financial risk, which increases sharply at the development stage, and the risk of failure which is at its peak at the outset of exploration. Risk is also divided into internal and external factors; some of the latter cannot be offset, viz. the systematic overall risk for any enterprise. The recently emergent risk embodied in withdrawal of large areas from exploration access is discussed. An appeal is made for objective multiple land-use policies to be applied so that land remains available at reasonable cost and with appropriate environ- mental safeguard conditions. Risks specific to gold exploration are discussed. As gold now accounts for over 50% of all mineral exploration, and most other metals are depressed, any sharp decline in gold will have grave effects on the ex- ploration industry. Gold exploration will become more difficult and expensive in about five years, after most of the readily accessible deposits in Australia are found. Government's role is important in pro- viding stability and basic data at reasonable cost. Exploration for specific minerals or of particular areas could be stimulated by extending the 150%.tax deductibility of R & D to aspects of exploration of strategic im- portance, particularly in the event of a downturn. Exploration is classic scientific research, at least through to the proving Stages.

Jan 1, 1987