Search Documents

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By R. W. Bartlett

DISILICIDE coatings, MeSi2, on refractory metals are usually grown by a solid-state diffusion reaction similar to the parabolic oxidation of metals. Two or more silicide compounds occur in each of the binary silicon-refractory metal systems. When an adequate source of silicon is available during the coating process, the lower silicide compounds are usually not formed.1 However, during service application of the coated refractory metal, continued heating causes further diffusion and growth of the lower silicides. A study of the growth kinetics of the lower silicides in the molybdenum and tungsten binary systems with silicon was previously reported.2 The present study is concerned with the growth kinetics of Ta5Si3 and Cb5Si3, formed as conjugate layers between TaSi2/Ta and CbSi2/Cb diffusion couples, respectively. Diffusion couples consisting of disilicide-coated tantalum and columbium sheet coupons were subjected to diffusion heat treatments, cross-sectioned, and scanned by an electron-microprobe analyzer to determine the relative X-ray intensity profiles. These profiles correspond closely to concentration profiles for the constituents, and were used to identify phases and locate phase boundaries. The analysis of a single specimen after a diffusion-anneal provides only one value for the Me5Si3 phase thickness, corresponding to the time and temperature of the diffusion treatment. Consequently, each isothermal curve showing the rate of accumulation or depletion of silicide phases required several samples with identical diffusion temperatures but different diffusion times. The disilicide coatings were prepared by pyrolizing commercially pure silane in a hydrogen carrier gas. The hydrogen was purified by passage through a palladium membrane. Commercially pure tantalum and columbium sheet metal coupons, 0.005 by $ by 2 in., were used. All of the coated specimens for each system were prepared together in a single group in order to minimize coating variations among individual specimens. During pyrolysis, the brightness temperature was maintained at 1200°C. With suitable flow rates at this temperature, only the disilicides of tantalum and columbium were formed in detectable amounts. Coated specimens were subjected to diffusion an-neals in a tube furnace with automatic proportional control within ±10°C. A H2-Ar mixture, deoxidized and dried over anhydrous magnesium perchlorate, was used to prevent oxidation during the diffusion anneal. Diffusion couples were cross-sectioned, polished and examined with an A.R.L. electron-microprobe X-ray analyzer. Both metal constituents in each specimen were simultaneously scanned using a 1-p beam spot size and either 1- or 2-µ steps. Analyses were performed using the Ka radiation of columbium and silicon, and the La, radiation of tantalum. For all specimens, an acceleration voltage of 30 kv was used, and integration was made against the specimen current. LiF and A DP monochrometers were used to isolate characteristic radiations. Three or more traverses were made on each specimen. The intensity scales were adjusted using the constituent metals and standard samples of the silicide compounds which had been verified by X-ray diffraction. The relative intensity profiles were used directly, in conjunction with the standard samples, to identify compounds and phase boundaries. The stoichiometries differ considerably between the silicide compounds in both systems, and the homogeneity range for these silicide compounds is narrow. These characteristics result in marked differences in relative intensities of the fluorescing elements—differences which permit ready identification of phases and phase boundaries. Projections of both electron back-scattered images and characteristic

Jan 1, 1967

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou' measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman' calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay' are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou' and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil' calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult's law within the requirements

Jan 1, 1957

By R. E. Ray, J. W. Stevenson, J. A. Berry

Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting insignificant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1986

By C. E. McManus

MANY mechanical advances have been made on mining equipment during the year 1951. There have been a number of trends established and many modifications made on open-pit equipment to increase the efficiency and availability of all the machines necessary in the moving of overburden and iron ore. Some years ago, the trend toward larger shovels for the loading of off-highway trucks began, but in the last year, it has become general practice to use the 5 to 7 ¼ -yd quarry-type shovels in the loading of haulage units. For years these larger shovels were used in the locomotive haulage pits. As the truck capacities increased from 15 to 20 to 30 tons, the need for larger loading units became apparent. Today in most mines, large shovels are in evidence and a few 8-yd shovels will be delivered this year for loading off-highway trucks. Torque Converter-Shovel The Diesel-driven shovel with its friction bands has been modernized with the torque converter. There have been about ten shovels remodeled to take a torque converter in the drive system. The large high-torque, low-speed Diesel engine was removed and replaced by a high-horsepower, high-speed, automotive-type engine. This engine was connected directly to the torque converter. The torque converter was connected to the shovel through the standard original sprocket and chain. Dual governors controlled engine performance. One governor controlled the high idle of the engine; the other governor, which is connected through a flexible shaft to the output shaft of the converter, controlled the loading of the engine. With this dual governor hook-up, the engine anticipates load conditions and is operating at high idle and full throttle before the shovel load is transmitted back through the converter to the flywheel. It has been found that with this automotive-type engine and converter, the shovel capacity has been increased about 20 pct. Also, the wear on the friction bands, breakage of hoist cables, and other mechanical breakages has been reduced materially. Alloy-Steel in Shovels The shovel equipment manufacturers have been experimenting with low-temperature-strength, high-alloy steels to combat the excessive breakage that occurs in extremely cold weather. High-nickel alloy steel has been used in critical areas that are affected by low temperatures, the most notable being dipper sticks. Most shovels ordered today are equipped with some of this special, alloy steel. More and more manganese alloy is being used for replacement parts such as shovel pads, idlers, drive sprockets, etc. Although the initial cost of these parts is considerably higher than the standard replacement items, the life of these manganese parts is considerably longer and well worth the added expenditure. Dipper-teeth repair is still a problem. Most companies use the small replaceable inserted tooth. It has become common practice among some of the companies to "job out" their dipper-tooth repairs to outside welding companies. This necessitates an additional inventory of teeth, but it does guarantee an adequate supply of replacement teeth at all times. These contractors have set up their shops on a production basis and can do an acceptable job at a high rate of speed. Thermite welding has been used in retipping teeth. To date, the process cannot be called successful but with improvements the time required to repoint the dipper teeth will be decreased considerably. The submerged arc process has been tried in the replacement of these dipper points, but like thermite welding has not proven successful. Here again, if a method can be developed to use submerged arc, the job of teeth repair will be made much easier. New model shovels in 6 ½ and 8 cu yd sizes fea-

Jan 1, 1952

[Separates of all the Technical Publications published in 1930 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions.] Metal Mining Technical Publi- Title Author Meeting Tran~. cation Volume No. and Page* 264-A.29 Quicksilver Industry in 1929. Im- L. H. Duschak San Francisco T30, 283, 319 provements in the Metallurgy of C. G. Maier and Oct., 1929 Quicksilver and Symposium on The others Present Status of the Quicksilver Industry (With Discussion) (37) 271-A.30 Observation on Ground Movement R. E. Palmer New York T30. 168 and Subsidences at Rio. Tinto Feb.. 1930 Mines, Spain (20) 274-A.31 Development and Installation of the C.L.Berrien New York T30, 139, 166 Hawkesworth Detachable Bit (29) Feb., 1930 276-A.32 Protective Measures . Against Gas 0. A. Glaeser New York T30, 129. 167 Hazards at United Verde Mine (11) Feb., 1930 287-A.33 Use and Cost of Compressed Air (12) R. S. Lewis New York Feb., 1930 314-A.34 Miami Copper Company Method of F. W. Maclcnnan New York T30, 39, YO Mining Low-grade Orebody (44) Feb., 1930 319-A.35 How Human Beings Respond to W. J. McConnell New York Changing Atmospheric Conditions Feb., 1930 (9) 324-A.36 Vertical and Incline Shaft Sinking at Arthur B. Foote San Francisco T30, 87 North Star Mine (21) Oct., 1929 32bA.37 Governmental Control of the Pro- W. E. Colby New York duction and Sale of Mineral Re- Feb.. 1930 sources (With Discussion) (16) 333-A.38 Some Recent Developments in Open- E. E. Hunner New York T30, 106, 117 pit Mining on the Mesabi Range Feb.. 1930 (25) 334-A.39 Mining Methods and Costs at Presi- V. D. Howbert El Paso dio Mine of American Metal Co. of R. Bosustow Oct., 1930 Texas (15) 339-A.40 Operation of Pressure Fans in Series W. 8. Weeks New York (8) V. 6. Grishkevich Feb., 1931 364-A.41 Top Slicing with Filling of Slices as H. Willey El Paso Used at the Charcas Unit of Com- Oct., 1930 pania Minera Asarco, S. A. (17) 373-A.42 Drill Sampling and Interpretation of H. T. Matson New York Sampling Results in the Copper G. A. Wallis Feb.. 1931 Fields of Northern Rhodesia (17)

Jan 1, 1930

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

EXPERIMENTAL work on the properties of high-purity alloys of the copper-manganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. PREVIOUS WORK Heusler1 conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilibrium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alphabeta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350° to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur5 have also noted this precipitate Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

By J. Gordon Parr, D. H. Polonis

IN a previous study of hypereutectoid Ti-Ni alloys' a substructure was observed in quenched powder specimens when the constitution was 100 pet retained ß body-centered-cubic phase. The alloy powders were quenched from 1000°C by a blast of helium gas and precautions already described were observed throughout the work, to minimize contamination. Ogden et al.2 have previously observed subboundaries in the ß phase of a Ti-Mn-N alloy; but this structure was attributed to nitrogen-rich a precipitation. The nitrogen content of the Ti-Ni alloys does not exceed 0.02 pet and the quenching rate was sufficiently rapid to suppress precipitation reactions. Since X-ray diffraction results have confirmed the absence of any second phase which might account for this phenomenon, it seems unlikely that this substructure is explicable in terms of nitrogen content. Fig. 1 shows the substructure in adjacent grains of 100 pet ß phase in a quenched 6 atomic pet Ni alloy. Fig. 2 shows adjacent ß grains in a similarly treated alloy; one grain contains marked intracrys-talline boundaries and the other is completely free from any substructure. The suberystals appear to have fairly regular shapes, suggesting a regular orientation relationship among them. Tempering the retained ß structure at temperatures below the eutectoid eliminates the substructure at an early stage of ß decomposition. At the present time it is possible only to guess at an explanation for this subboundary phenomenon, since very little work has been reported on substructures resulting from phase changes. It is believed that the present phenomenon is due to poly-gonization resulting from unrelieved stresses set up

Jan 1, 1957

By W. N. Carr, J. R. Biard, B. S. Reed

An analysis of the semiconductor injection laser is presented which is based on a phenomenological model using device and material parameters. The intent of the laser threshold analysis is not to predict from theory the actual threshold current density but rather to provide a logical means of interpreting experimental results. The device and material parameters have been selected such that they describe both the threshold conditions and quantum efficiency of the lasev. A technique is proposed whereby the current required to obtain a population inversion is predicted from device 1-V characteristics. Experimental data are presented which support the analysis. THIS investigation is concerned with the characteristics of GaAs lasers fabricated in this laboratory. However, the assumptions used in these calculations should not limit their application to GaAs alone. It is felt that the analysis is sufficiently general to be useful in describing the operation of other semiconductor-laser materials. ANALYSIS heavily doped semiconductors to be considered. The absorption and/or generation of optical radiation may be completely specified in terms of q(E) and the probability functions f,,(E) and f,(E) which define the occupancy of the valence-band and conduction-band levels, respectively. The symbols used in this analysis are listed at the end. Following the approach of all' it can be shown that the effective gain coefficient, g, in the plane of a forward-biased P -N junction is g(E)=-ai@)[1-fv(E)-fc(E)] [1I In particular Eq. [I] holds for the photon energy at which lasing occurs, Ep. Throughout the following discussion Eq. [I] is considered only for the lasing transition E = Ep. For simplicity the functional energy dependence of the various factors is omitted in subsequent equations. Unless otherwise stated the symbols used represent the values at Ep. If the analysis is limited to the P-type side of the laser junction, the function q(l -f,,) is recognized as the band-to-band absorption in the P-type material at thermal equilibrium. Under forward-bias conditions the function f, is determined by the electron quasi Fermi level in P-type material. For sufficiently large forward bias the second term in Eq. [3] will become dominant and net gain will result; i.e., g will become positive. In order to simplify the subsequent analysis several assumptions are in order at this point. a) No conductivity modulation occurs. /„ is independent of f, and therefore go is a constant. b) The P-type material is heavily doped such that the degeneracy of the valence band permits popu-

Jan 1, 1964

By John V. Beall

Monotonous flood planes flanked either side of the road as we drove in the embassy car from the airport to downtown Seoul. We crossed the brown waters of the Hann River, meandering over mud flats. A great, gnarled tree bore beautiful fall colors of gold. "That is a Ginko Tree, the oldest living fossil, probably a hundred million years old;" said Jean W. Pressler. Compared to other cities of the Far East, the traffic in and around Seoul was sedate. Few motorcycles or bicycles, and little superfluous horn tooting. "This is the best season in Korea. We have long beautiful springs and falls," said Pressler, chief of the mining branch of USAID, and he continued with a briefing on the country.

Jan 8, 1969

By H. P. Willard, R. W. Gates

Basic Inc., has been mining magnesite and brucite for 27 years at Gabbs, Nev. This is a medium sized open-pit mine. The magnesite deposits are in north-western Nye County about 30 miles east of Luning, Nev., on the west slope of the Paradise Range, at an elevation between 5000 and 6000 ft. The magnesite and associated brucite is used to make magnesia refractories employed principally in the steel industry and magnesium oxide for various chemical uses.

Jan 10, 1963

By A. H. Larson, L. G. Twidwell

DURING the roasting of zinc sulfide concentrates and by-product recovery from flue dusts, the zinc sul-fate phase may occur in various stages of the processes. In addition to zinc sulfide, other sulfide phases are usually present such as CdS, PbS, CuzS, and FeS. Consequently, the effect of these sulfides on the thermal decomposition of ZnS04 was investigated. Merck high-purity, anhydrous zinc sulfate was used as the starting material. The sulfate was heated under an argon atmosphere, at a rate of 10°C per min. With the first slight indication of decomposition as determined by gas analysis, the sample was removed from the furnace and allowed to cool. X-ray patterns showed no other phase present. It is estimated that less than 0.05 pct of the ZnS04 decomposed. The metal sulfides were also heated under an argon atmosphere to drive off any adsorbed water. The materials were then sized (-200 to +270 mesh), mixed in predetermined mole ratios, and pressed into pellets. The experimental measurement of the reaction rate consisted of purifying the argon carrier gas, continuous flushing of the heated reacting mixture with argon, and collection and analysis of the SOn product gas. The reaction system was heated to 600°C and al-

Jan 1, 1967

A record $18.7 billion worth of metals, non- metals and fuels was produced in the U.S. during 1962, according to a year-end estimate from the USBM. The 1962 total value, based on preliminary statistics compiled by the Bureau, was nearly $600 million more than in 1961. Most minerals gained both in value and volume of production during 1962 according to information collected by the Bureau. All mineral fuels except anthracite showed increases. Among nonmetallic minerals- other than fuels-gains exceeded losses by two to one. Metal production held steady as gains and losses balanced.

Jan 2, 1963

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-The following report covers briefly some of the more important activities of the Institute during the year 1923. In my report for the year 1922, I drew attention to the falling off in membership of the Institute due to the depressed condition of the mining industry in several lines and the inability of many of our members to find profitable employment in mining or its associated branches. A number who were unemployed during 1922 established connections during 1923, but a still greater number have been forced to resign or drop their membership during 1923. Fortunately, the number dropped is not so great as in the previous year. The Employment Service conducted by the four Founder Societies bears witness to the trend in business. For the young men just out of college, there are plenty of opportunities at small salaries, there are plenty of opportunities for them as laborers; but for the mature members, those of experience, there are few calls. During the last eighteen months, our Employment Service has been able to place only six of our members out of every hundred engineers for whom it has found work. Another loss which this Society has suffered, but which is not felt so keenly by our sister societies, is in its foreign members. The A. I. M. E. has always had a large foreign membership, but of recent years exchange has been so heavily against many European and South American countries that a large number of members residing abroad have been compelled to relinquish their membership. Almost invariably these members express keen regret because of the necessity that confronts them, and almost invariably the writers express hope that present conditions will not last long and that they will soon be able to ask-for reinstatement. Having stated the darkest side of the picture first, it may now be drawn to your attention that in spite of these losses the number of persons applying for membership was decidedly encouraging.

Jan 2, 1924

TO THE BOARD OF DIRECTORS, AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS: Gentlemen.-I have the honor to present the following report of the President for the year 1919. In order that this report may be printed and distributed to the members in advance of the February meeting, it is necessary that it end with the calendar year 1919. Any activities during the first six weeks of 1920 will be covered in the Secretary's report for the year 1920. VISITS TO MEMBERS Your President has visited each of the Local Sections of the Institute, with the exception of the ones at Washington, D. C., Tulsa, Okla., and the Nevada Section. These three sections have not arranged meetings at which the President could be present. In addition, your President, accompanied by President Jennings and Secretary Stoughton, in the year 1918, attended meetings of members in Minneapolis and Duluth, Minn., and Houghton, Mich. A dinner and meeting of the members in Pitts-burgh, Pa., was also attended, in company with the Secretary and your President also attended the meeting of Canadian Mining Institute in Montreal, in March, 1919.

Jan 2, 1920

By K. Takahashi, I. Iwasaki

it is well known1 that racemic mixtures of optical isomers can be separated by passing their solutions through a column packed with r- or 1-quartz powder so that one of the isomers becomes adsorbed selectively on the asymmetric quartz surfaces. Although the natural occurrence of r- and 1-quartz is more or less equally distributed, some localities show enough deviations toward a higher proportion of l-quartz2 to suggest that optical isomerism might influence quartz flotation. Beta-amines have an asymmetric carbon atom, and therefore optical activity may be expected. Beta-amines are reported to behave quite differently from alpha-amines in the flotation upgrading of certain oxidized iron ores.3 It is of interest, for both practical and theoretical reasons, to determine whether or not optical isomerism plays a role in the amine flotation of quartz. In this article the results of Hallimond tube flotation tests and of adsorption measurements using d-beta-phenylisopropylamine on both r- and 1-quartz are compared. D-beta-phenylisopropylamine was chosen for the tests because it is commercially available in optical isomers. MATERIALS AND METHODS Brazilian quartz crystals were hand-sorted according to the difference in trigonal trapezohedral faces, and each crystal was further checked by the Airy's spiral.4 The respective crystals were then crushed, and the -150 + 200-mesh fractions were screened out for the Hallimond tube tests. The samples were cleaned by brief leaching with warm, dilute hydrochloric acid, and then by repeated rinsing with distilled water. In preparation for the adsorption measurements, they were then dry-ground in a pebble mill for several hours, washed a few times with distilled water, and finally dried in a vacuum desiccator. By means of the Krypton gas adsorption method, the specific surfaces of r- and 1-quartz samples were determined to be 27,700 and 19,800 sq cm per gm respectively, the difference being due mainly to the decantation procedure rather than to the inherent difference in their grindability. D-beta-phenylisopropylamine was the only collector used in the study. It was solubilized by neutralizing with 110% of the stoichiometric requirement of 0.1 N hydrochloric acid. The specific rotation of the d-beta-phenylisopropylamine was determined with a polari-meter using sodium D line to be, Although the d-beta-phenylis~prop~lamine showed absorption maxima in the wave length region of 250 to 270 millimicrons, due presumably to the phenyl group, these peaks were too sensitive to be used for colorimetric determination of the residual concentration in the adsorption measurements. The amine-picrate method, used in the colorimetric analysis of dodecylammonium chloride,' was found to work satisfactorily for the d-beta-phenylisopropylamine. The adsorption densities were thus determined after equilibrating 40 gm of the ground quartz sample with 300 ml of solution by tumbling in separate glass-stoppered Erlenmeyer flasks for one hour. EXPERIMENTAL RESULTS Fig. 1 presents the adsorption densities of d-beta-phenylisopropylamine on the r- and 1-quarts in the pH range of 6 to 7.5. In agreement with data reported in the literature, the adsorption density of d-beta-phenylisopropylamine was slightly higher on the r-quartz than on the 1-quartz, although the difference was not as pronounced as one might expect from the capacity of r-quartz and 1-quartz to separate racemic

Jan 1, 1969

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.' This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

By R. D. Carnahan, G. A. Stone, R. J. Arsenault

An experimental technique has been developed for carrying out a dynamic tensile stress-strain test in which plastic strain is measured continuously throughout the microstrain region extending through the macroflow region to total deformations of 5 pet. The tests were carried out on niobium, samples having interstitial impurity levels of 160 and -800 ppm at temperatures ranging from room temperature down to 100°K. A band spectrum of activation energies was obtained from calculations based on the measured activation volumes and temperature dependence of flow stress. The inability of a single rate-controlling process to predict such a phenomenon has led to the proposal that several sequential rate-controlling dislocation mechanisms are operative in the preyield micro-strain region. These are thought to be: the motion of geometrical kinks, the formation of double kinks in edges, and finally in the macrostrain region the formation of double kinks in screws. In less pure niobium the effect of interstitial impurities is shown to be dominant in the microstrain region, suggesting that a fourth probable mechanism is overcoming interstitial barriers instead of geometrical kink motion and the formation of double kinks in edge dislocations. THE principal fundamental aim of most mechanical properties studies of crystalline solids is to determine the dislocation mechanisms responsible for the plastic behavior. The extension of such studies to the region of preyield microstrain behavior has received renewed attention in the past few years as the details of macroscopic flow behavior have become better understood. For the most part, microstrain studies have been carried out using one of two variations of a single experimental technique.1 The first method involves loading the sample at a constant extension rate to a predetermined stress level (less than the macroscopic yield stress), instantaneously unloading, and then determining the extent of plastic deformation to a sensitivity of 10"6. The microscopic stress-strain curve is then constructed from the results of a repeated series of such individual measurements, each of which involves loading to an incrementally higher stress level, by relating the accumulated plastic microstrain for each step to the maximum applied stress in that step. The second variation, also carried out by step-wise increases in stress, measures the total strain to a sensitivity of ~10"6 and relates the maximum stress to the area of closed hysteresis loops that are generated under certain conditions (namely, prestrained samples). The foregoing methods have yielded interesting information about the nature of preyield deformation and plastic response to stresses below the yield stress, but they offer certain disadvantages for studying the dynamic behavior of dislocations. In the first method it is physically impossible to specify a plastic strain rate inasmuch as the test sample is reexposed, as it is loaded to its maximum stress in a particular step, to lower stresses at which flow will take place. The strain corresponding to a given stress level on the stress-microstrain curve thus generated will then always be greater than that at the corresponding stress level of a truly dynamic test carried out at the same extension rate. The second method has been used to obtain correlations with dynamic macroscopic flow parameters by applying dislocation damping theory to the hysteresis loop areas.2 The approach has had some success but suffers in that only samples that have been prestrained a few percent can be studied. Although the stresses

Jan 1, 1968

By H. Morgolin, M. A. Greenfield, P. A. Farrar

In attempts to correlate mechanical properties with microstructure, it is desirable to determine the effect of ß grain size. Determination of 6 grain size is not a problem where a has precipitated at ß grain boundaries. However, in alloys which have been processed to produce an equiaxed a +ß structure the ß grain size is difficult to determine because ß grain boundaries do not etch. The ß grain size can sometimes be laboriously determined by searching for grains which have some a! outlining the 6 grains. This difficulty of ß grain size determination in equiaxed a + ß alloys can be overcome by heating below the ß transus temperature for a short time and water quenching. Fig. 1 shows the starting equiaxed a + ß structure of the Ti-5.25A1-5.5V-0.9Fe-0.5Cu alloy used in this investigation, and Fig. 2 shows the microstructure of the same sample water-quenched after heating 1 min at 1675"F, which is 25°F below the 0 transus. The heavily etched microstructure consists of some equiaxed a! in a structure showing considerable amounts of transformed ß. The ß grain

Jan 1, 1969

By D. W. Levinson, L. E. Tanner

DURING the course of an investigation of the zirconium-iron-tin system the zirconium-iron system was reexamined up to 55 pct* Fe. The alloys pre- visible melting3 and X-ray diffraction studies were made of samples of the alloys. The ferromagnetic properties of ZrFe2were determined by Professor P. W. Selwood* using a modified Faraday balance.4 The zirconium-rich portion of the phase diagram is presented in Fig. 1 and compared with the work of Hayes et al.1 The maximum solubility of iron in ß is somewhat decreased while the eutectic temperature is raised. There seemed to be no change in the eutectic composition of 16 pct Fe. Since the base material was so low in iron content, it was possible to establish the maximum solubility in a between 0.017 and 0.025 pct Fe at the eutectoid temperature. The observation of fine ZrFe, particles in the micro structure of a specimen of 0.012 pct Fe alloy quenched from 700°C indicated that the solubility drops below this composition at 700° C and lower. Further study was made of the intermediate phase ZrFe2. wallbaum5 identified the compound initially as ZrFe2 with a C 15 (MgCu2) structure, placing it at 55 pct Fe stoichiometrically. Hayes et al.1 believed they found the phase at about 47.2 pct Fe and called it Zr2Fe3 but reverted to ZrFe, in the discussion of their paper.6 Jordan and Duwez7 confirmed Wallbaum's work as well as finding the same single-phase structure to about 62.3 pct Fe or Zr0-61 Fe2-18. In order to establish the ternary phase relations in the zirconium-iron-tin systema the exact position of this phase had to be known. This was accomplished by X-ray diffraction, visible melting, and metallographic techniques. Elliott8 obtained a single-phase ZrFe2 X-ray diffraction pattern from an alloy of about 55 pct Fe. This was confirmed in the present study with an alloy of 54.81 pct Fe. However, extra lines (attributable to a or ß zirconium) were found in diffraction patterns of the 47.42 and 49.83 pct Fe alloys. The melting characteristics of these same alloys were studied by suspending 47.42, 49.83, and 54.81 pct

Jan 1, 1960