Search Documents

By Bradley Stoughton

PROMINENCE has been given lately in engineering circles to the question whether an organisation with manifold interests can be as effective as one with a single aim, especially if that single aim be the furtherance of affairs of moment and the welfare of engineers in general. In its earlier days, the A. I. M. E. was forbidden by its constitution to engage in non-technical public affairs, but the members altered the constitution in this respect, in the year 1912, in response to the growing demand that engineers be more human in their interests and that the engineering societies represent them in this respect. Since that time, the activity of mining engineers in public affairs has been growing rapidly, and we are happy that the Institute has been able to render very valuable economic services. Doubtless the greatest public service rendered by engineers in a recent great emergency was the work of the Naval Consulting Board, without which the U. S. Navy would never have been able to enter promptly into service upon our entrance into the war, ,and both Navy and Army would have been a long time without the munitions that came at an early date. We can never forget that this Board was established through the direct activity of the then President of the A. I. M. E., with the hearty cooperation of other national organizations.

Jan 1, 1920

By Earl E. Hunner

At the end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping southwest, or exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a north-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly. Problems and Plans In order to understand what follows, the general layout and equipment of the mine as it was at this time must be briefly described. Fig. 6 indicates the relative positions of the shafts. The North Star (incline) shaft extends from the surface to the 6300-ft. level following the vein, with an average pitch of 26", between limits of 11" to 38. There is at present no hoisting equipment in this shaft between the 2700 and 4000-ft. levels. The Central (vertical) shaft connects with the North Star shaft at the 4000-ft. level, at a vertical depth of 1600 ft. In two compartments of this shaft 4-ton skips made a vertical turn of 15 ft. radius at the 4000-ft. level and ran down the incline to the 6300-ft. level. A cage operated in the third compartment to the 4000-ft. level. Men and supplies were transferred to a truck running on a third track down the incline shaft to the 6300, operated by an electric hoist on the 4000-ft. station. When the shifts changed double-deck cages were substituted for the skips in the vertical shaft, but they stopped at the 4000-ft. station. The truck to 6300 carried 22 men, and it required 8 min. to make a trip down and back. This arrangement was satisfactory as long as a fairly large proportion of the work was

Jan 1, 1930

By S. H. Ash

IN no part of the world other than a small area in Pennsylvania is anthracite mining an industry of major magnitude. As the deposits of anthracite in the United States are limited virtually to Pennsylvania, the difficulties of this industry have been commonly considered a state rather than a national problem. However, there is also national interest in the conservation and wise utilization of all the country's fuel resources and in the control of interstate waterways. The anthracite industry is confronted with a serious problem of water accumulation in many of the mines, a problem that must be solved in the near future if progressively higher mining costs are to be avoided. It cannot be solved by the operating companies without state or Federal aid, or both, owing to the magnitude of the work required, the diversity of interests of the coal and surface ownerships, the hazard to the whole mining community, and interests affected outside the mining region. 'The costs of abating the ever-increasing surface seepage to mine workings and of handling this seepage once it has occurred are beyond the eco¬nomic resources of the operating managements.

Jan 1, 1941

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M.. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information-will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries: All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute. can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will he classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 5, 1913

The Bureau of Mines extends. a cordial invitation to all members of the Institute to visit Pittsburgh, Sept. 29 to Oct. 1, to participate in the dedication of the Mines Experiment Station. Accompanying this will be a nation-wide participation in a First-aid and Mine Rescue Contest. The Pittsburgh Chamber of Commerce will cooperate. The Institute will be represented by a special delegate appointed by the President. MONDAY 8:30. A. M. Bureau Building open for inspection. 10:30 A. M. Dedicatory Ceremonies in rear of Main Building, .4800 Forbes St. 2:00 P. M.. Special Train and Automobiles to Experimental Mine near Bruceton, Pa. 3 to 6 P. M. Mine Explosion and Inspection of Experimental Mine . and of Explosives Testing Plant near Bruceton, Pa. 6:00. P. M. Return by Special Train and Automobiles to B. & 0. Station, Pittsburgh. 8:00 P. M. Informal Reception and Organ Recital Carnegie Music Hall. Arranged by Carnegie Institute of Technology.

Jan 9, 1919

By R. W. Gurry, L. S. Darken

The solubility of cementite in austenite is computed by thermodynamic methods from the observed solubility of graphite. It is found that the solubility of cementite is greater than that of graphite in the entire austenite temperature range. Thus the prior discrepancy between this portion of the phase diagram and the observed metastability of cementite is partially resolved. FOR several years it has been apparent that a serious discrepancy exists in certain observations pertaining to the Fe-C system. Direct experimental data indicate: 1-That the curve representing the solubility of graphite in austenite'" crosses that for cementite4 at about 945°C as shown in Fig. 1. 2— That graphite and austenite saturated therewith are stable1 relative to cementite at all temperatures between the eutectoid, about 723°C, and the eutectic, about 1153°C. These observations are mutually incompatible in view of a well-known consequence of the second law of thermodynamics, namely, that the stable phase (presumably graphite at all temperatures) has a lower solubility than the metastable phase (presumably cementite). Hence either 1 or 2 above must be in error; either the measured solubility of graphite or of cementite, or the observation as to the stability of graphite, is in error. Our present purposes are: 1—To collate the available data on cementite and prepare a table of HO — HO° and of (Fa— HO°)/T. This tabular method seems the best and most convenient way to represent the heat and free energy of formation. 2—To determine whether the measured solubilities of cementite and graphite in austenite are in accord with the above table and the measured thermodynamic properties of austenite, in order to resolve, if possible, the existing paradox of these two solubilities. Enthalpy of Cementite The enthalpy of cementite at 273 °K, H279 — HOcem, was computed by integration of the low temperature heat capacity as measured by Seltz, McDonald, and Wells" 68" to 298 °K) and as given by the Debye functions recommended by them (0" to 68°K); the result is included in Table I. At higher temperature HCem — H,,"" is given by Kelley who used the data of Naeser7 (298" to 1037°K) and of Umino8,9 (273° to 1923°K). We have recalculated Hcem — H273 cem from the data of UminoO in the following way. In the equilibrated alloy at temperature the weight fraction of cementite Pct c -Pct cr is PctC -PctCr designated f(C), and the

Jan 1, 1952

By Norman J. Sather

LOCATION AND HISTORY The Bunker Hill Mine is situated on the south side of the Coeur d’Alene River in Shoshone County of Northern Idaho near the City of Kellogg. Kellogg, the largest in the Coeur d’Alene District cities, is at an elevation of 2,300 feet and has a population of approximately 7,000 people. It can be reached by air, railway or highway. The history of the Bunker Hill Mine dates back to August 26, 1885, when Noah S . Kellogg found the outcrop of the Bunker Hill ore body on the hillside above the present town of Wardner, Idaho, in Milo Gulch. A small concentrator was erected in 1886. Before the railroad came, the mine output was transported by mule teams to the head of navigation on Coeur d’Alene Lake. After ten years of production, an interest was purchased in the Tacoma Smelter at Tacoma, Washington, to which the entire output was shipped. In 1916 and 1917 a modern lead smelting plant and refinery was erected and in 1927 and 1928, a modern Electrolytic Zinc Reduction Plant was built and put into operation by the Sullivan Mining Company which was 50% owned and now totally owned by The Bunker Hill Company. GEOLOGY AND MINERALOGY The Bunker Hill ore bodies are found in gray and greenish gray quartzite and argillaceous quartzite of Precambrian age and are known as the Revett and St. Regis formations. Most of the ore bodies are found in the St. Regis formation.

Jan 1, 1970

By SIDNEY ROLLE

ACURSORY glance through the literature on the subject reveals that the ablest minds in the land are devoting themselves to the great question of labor, of which employment is one of the fundamentals. Volumes have been written and the end is not in sight. Employment management is today about in the position that efficiency was 15 years ago. During the early days of the war, and perhaps for a year or so before, labor was plentiful. As the war progressed and Europe drew on us for munitions, employers began to compete with one another for', all, classes of labor. Labor was difficult to obtain, wages rose, the labor turnover increased, and employers began to install employment departments, welfare plans, and all sorts of schemes, but the labor efficiency dropped. As the war progressed, greater and greater production was demanded. New factors were introduced each day. The government, labor unions, industrial councils, all tended, it seemed, to make the situation almost intolerable. Wages rose to fantastic heights, the cost of living rose higher and higher, and the efficiency dropped still further.

Jan 1, 1921

By J. J. Jonas, J. L. Uvira

Equipment was constructed which permitted the hot compression of 99.8 pct Armco iron and 2.8 pct Si steel at constant true strain rates of 0.05 to 1 per sec over the temperature range 600" to 1000°C. A maximum true strain of 1.9 could be attained, followed by immediate quenching or by isothermal annealing. True stress-true strain curves were obtained, and the steady-state flout stress, a, strain rate, i, and temperature, T, were found to fit the following expression: The constants A, a, n', and AH were determined for the two ,materials. The activation energies obtained for Arrnco iron and silicon steel are 66 and 80 kcal per mole, respectively, and approximate those for seu- diffusion and for creep. This indicates that hot compression is a diffusion-controlled thermally activated process. THE hot compression of iron and steel is usually carried out in the austenite temperature range,1"7 as this is the one of greatest interest with respect to industrial hot working. However, a disadvantage of testing in the austenite range is that the hot-worked structure is destroyed by the phase transformations taking place during cooling. The present study was therefore carried out in the ferritic temperature range, and the hot-worked substructures were preserved by rapid quenching after deformation. The substructural results will be described in a separate paper, and the present communication is restricted to the strain rate/stress/temperature relationship observed during hot working. The results of hot-compression testing are usually given in the form of true stress/true strain curves, with a different curve for each temperature/strain rate ~ornbination.',~,~ Sometimes simple algebraic equations are fitted to the curves, so that certain extrapolations or interpolations can be performed.1'2'5 These equations are, however, devoid of mechanistic interpretations. The present study was undertaken to show that hot compression can be described by an equation of the type used in creep studies. That is, it will be shown that the temperature dependence of the strain rate in hot working is well-represented by an Arrhenius term, with an activation energy similar to that for creep. Also it will be seen that the stress dependence of the strain rate is similar to that for creep EXPERIMENTAL METHOD AND MATERIALS The investigation was carried out with the following three ferrous materials: 1) Armco iron; 2) Armco iron with 0.26 pct Mn; 3) 2.8 pct Si steel. The first two materials were utilized for investigations performed in the temperature range 600" to 800°C; the last one was used for tests at temperatures from 600" to 1000°C. The materials were of commercial purity,* as shown in Table I. Cylinders of five different sizes were prepared by strain annealing. The resulting mean grain diameter was 3 mm in the 1-in. Armco iron and 2 mm in the other sizes and grades. Different ratios of diameter/height were used to enable the determination of the coefficient of friction. The specimen faces were provided with concentric grooves, which acted as lubricant holders during compression, as recommended by English and ~ackofen' and others.2'9 Powdered glass lubricants were applied to the samples before hot compression to decrease friction and barreling, following the practice of previous investigator~.~~~~~~~~ Different mixtures of glass powder were used for each temperature, after the determination of suitable compositions by experiment.'' Equipment for Hot Compression. Hot-compression tests were carried out on an adapted 150-ton vertical hydraulic extrusion press and also on a modified high-temperature creep machine. The modified extrusion press was used for temperatures up to 800°C. The following items were added to the press: a) a high-temperature furnace with built-in upper and lower platens; and b) a transmission assembly, which permitted the attainment of logarithmically decreasing crosshead speeds. These accessories are described in detail in Ref. 11.

Jan 1, 1969

By J. P. Zannaras

Referring to the article by R. J. Charles and P. L. de Bruyn, let us assume that W = weight of glass bar; P = weight of hammer; e = total deformation; K = unit of deformation; K = potential stress energy; E = modulus of elasticity; L = length of the bar; 7 = coefficient of inertia; h = height, ft; V = velocity, fps; and a = cross section area. The portion of kinetic energy which is effective in producing stress energy in a fixed bar struck horizontally is given by the formula" 1 + 1/3 W/P K =1+1/3w/p/(1+1/2w/p)2 P.V2/2g = Ph where 1 + 1/3 W/P ? (1 + 3W/P/(1=1/2w/p)2 [8] Putting e e = W/P =------------ From the above equation it can be seen that the maximum transfer of kinetic energy to stress energy is when e = 0 or W/P = 0 which indicates that the weight of the hammer must be very large as compared with the weight of the impacted rod. Eq. 8 diametrically opposes the conclusions reached by the authors of this article. In fact, if their suggestions were followed to the extreme when e = co when P = 0, there would be no transfer of kinetic energy to stress energy at all, as 7, becomes zero. Eq. 8 presumes that the velocity with which the stress is propagated through the bar is infinite, whereas the authors claim that the compression waves reflected are reaching the struck end of the bar prior to the complete transfer of the kinetic energy to cause such modification of the conditions there as to make them reach the reverse conclusions demonstrated by the above formula. That such interference exists is unquestionably demonstrated by the authors and others. However, if my observations are correct, such interference for this specific experiment and also for practical comminu- tion is insignificant, and the conclusions of the authors are in error and must be reversed to comply with Eq. 8. Eq. 5, w. = AE 2/2, given by the authors on page 51, is derived from the following equation (Eq. 9): K = 1/2Pe, where P = Sa, S = ?E, e = EL, and L = 1. The above formula, Eq. 9, cannot be applied in this case. This formula is applicable for static loads where the load increases from zero up to its final value, P, in such a way that the deformation at different instants is proportional to the loads acting at those instants and actually represents the area of a right triangle in the strain load diagram of base e and height P. The typical photographs shown in Figs. 3 and 4 represent the familiar strain load diagrams, and since the line of the wave marks the existence and intensity of the strain with the unquestionable conclusion that such strain has been caused by the action of a load acting continuously all along the wave until it reached the horizontal axis, the work stored at this point is represented by the area under the wave line and the horizontal axis and not by the area of the fictitious triangle given by the authors. Then if this is correct, even visual estimation of these areas at gage stations given in the typical photographs of Figs. 3 and 4 suffice to contradict the authors' calculation given in Figs. 6a and 6b and Figs. 7a and 7b. The typical photographs presented by Charles and de Bruyn show a considerable variation of the intensity of the strain at different stations but very small variation of areas which actually represent the stress energy at the corresponding stations. And, apparently, by squaring the small quantities, the authors magnified their error tenfold. J. M. Frankland's paperV iscusses the relative strain intensity and not the total energy for different types of impact loading. He states in his paper, "The reader is explicitly warned not to confuse the results in this report with those obtained when the load is applied by a blow as from a hammer. In this case the peak load rises to very large but mostly unknown values. The accompanying large deflections and stresses are the result of high values of P, not of the dynamic load factor n. According to Frankland "the dynamic load factor" is the numerical maximum of the response factor. It therefore appears that the authors followed the same procedure in obtaining the relative strain energy ab-

Jan 1, 1957

By S. A. Bradford

Internal-oxide precipitates in decarburized a iron alloys were studied by microscopic and X-ray methods. Diffusion of oxygen is primarily trans-granular, although large amounts of manganese or PhosPhorus cause preferred grain boundary dimsion at temperatures below 1450OF. Transgvanular internal oxidation follows the parabolic rate law with an apparent activation energy of 60 kcal per g-atom for decarburized rimmed steel and around 50 kcal per g-atom for higher alloy contents. The internal oxide is (Fe,Mn)0. Evidence was found for a miscibility gap in the FeO-MnO system. UNTIL very recently, the internal oxidation of metals was studied primarily as a scientific curiosity or, in a few cases, as a means of strengthening alloys by precipitation hardening. However, with the recent development of low-carbon enameling sheet steel, internal oxidation has become a problem of practical importance to the steel industry. For example, in 1961 it was reported1 that internal oxidation of steel can occur during decar-burization by open-coil annealing and will reduce the notch ductility of the sheet unless the process is carefully controlled. The present study was therefore undertaken to learn more about the rates and mechanism of oxygen diffusion and oxide formation in iron alloys. BACKGROUND The process of internal oxidation has been well-defined in the literature:',' oxygen dissolves in an alloy, diffuses inward from the surface of the metal, and reacts to form a precipitate with the alloying element that will provide the most stable oxide. he growth of the finely divided so-called subscale, i.e., the internal-oxidation zone, depends on the diffusion rates of both the oxygen and the reactive element.4 Investigators have generally found that increasing the temperature increases the size of the oxide particles, the rate of subscale growth, and the tendency to transgranular diffusion. With very few exceptions, the square of the thickness of the internal oxide layer is directly proportional to the reaction time. Given two conditions easily satisfied for iron systems— a) an oxygen solubility much less than the concentration of the alloying metal and b) an oxygen-diffusion rate to the oxide boundary much faster than that of the alloying element—then the general expression developed by Rhines and co-workers5 for the parabolic growth rate of the internal-oxide zone can be simplified to the following form: where Co and CM are, respectively, the solubility of oxygen and the concentration of the alloying element, DO is the diffusion coefficient of oxygen, O/M is the weight ratio of oxygen to metal in the precipitated oxide, and x is the thickness of the internal-oxide zone after an annealing time t. Both the oxygen solubility and diffusion coefficient can be approximately expressed as functions of temperature by Arrhenius-type equations: in which H and Q are, respectively, the heat of solution and the activation energy of diffusion. Consequently, the apparent activation energies calculated from Arrhenius plots are the sum of the heat of solution of oxygen in iron and the activation energy for diffusion of oxygen. The data, if not the interpretation, of Schenck et al.8 bear out the fact that oxygen diffuses in the atomic form. The general rate law for atomic diffusion is: the reaction rate being proportional to the square root of the pressure at low pressures. Benard and Moreau8 studied both the surface oxidation of Fe-Ni alloys and the gradual penetration of oxygen into the metal. They observed that oxide particles first form along grain boundaries and then grow to form continuous films that eventually envelop the grains. The parabolic rate law does not usually apply in these cases, especially at the higher temperatures. The oxide formed is wustite which gradually transforms into Fe3O4 and finally into Kennedy and coauthors8 examined Fe-Ni alloys with 26, 75, and 84 pct Ni oxidized at 800°C and

Jan 1, 1964

By Arthur La Motte

I NDUSTRIAL explosives, as distinguished from military explosives, include high explosives and blasting powder. The high explosives which are best known are straight dynamite, gelatin dynamite, ammonia dynamite and permissibles. There are two kinds of blasting powder, saltpetre blasting powder and nitrate of soda blasting powder. Blasting powders are mechanical mixtures of nitrate of potash or nitrate of soda with sulfur and charcoal, highly compressed, granulated and glazed. They ignite from a spark and burn with relative slowness, the rate of burning and hence the rate of conversion into gases depending upon the size of the granulation and upon the degree of. confinement under which the powder is placed. High explosives, on the other hand, are chemical compounds which detonate; that is, when the explosive is subjected to a violent shock, provided in practice by a blasting cap or an electric blasting cap, the molecule of the essential ingredient, usually nitroglycerin, is disrupted and the energy and heat released cause any other explosive ingredients which may be present, such as ammoniuin nitrate or T.N.T., to decompose with a resultant evolution of gases at an extremely rapid rate varying from 6000 to 20,000 ft. per second.

Jan 1, 1924

By Richard F. Link, George S. Koch

About 50,000 assays of mine samples were required in a preliminary investigation of the distribution of gold, silver, lead, copper, and zinc in two large Mexican mines, the Frisco mine at San Francisco del Oro (Chihuahua) and the Fresnillo mine at Fresnillo (Zacatecas). The feasibility of working with so many assays rests directly on the use of machine processing methods. The purpose of this article is to describe the methods used because machine (or data) processing can also be used efficiently to make the many calculations from mine assays needed in mining operations. No particular originality is claimed for these methods, which are straightforward applications of standard procedures for machine processing. Inasmuch as machine processing is essentially a routine job once it is begun, procedures must be organized more completely than is the case where human judgment can be inserted at every step. Before undertaking any work, it is necessary to decide carefully just which data must be processed as well as the exact results desired.

Jan 9, 1960

By AIME AIME

T HE Executive Board of the American Engineering Council held its fourth meeting at St. Louis on the first anniversary of the organizing conference which met in Washington on June 3,1920. Representatives of a number of the leading engineering organizations in the vicinity of St. Louis were present by invitation. The members of the Executive Board were guests of the Associated Engineering Societies of St. Louis. They were given a delightful ride about the city and were entertained at the Glen Echo Country Club at dinner. The special committee that had been appointed to draft resolutions to Mr. Hoover submitted the following, which were adopted : WHEREAS, our President, Herbert Hoover, has been appointed Secretary of Commerce in the Cabinet of the President of the United States, and WHEREAS, in consequence of his acceptance of this high public office, he has deemed it necessary to tender his resignation as President of The Federated American Engineering Societies.

Jan 1, 1921

By Karl V. Lindell

THE Jeffrey mine of the Canadian Johns-Manville Co., Asbestos, Que. has operated for a number of years, supplying the parent company, Johns-Manville, raw material for asbestos products. The mine is situated in the 70-mile-long serpentine belt running from Asbestos, Que. on the west to East Broughton on the east. This district is the most important producing area in the world of quality spinning-fiber asbestos, with 11 operating mines supplying 70 pct of the world's needs. The Jeffrey mine, located 90 miles from Montreal and approximately 35 miles southwest of Thetford, accounts for 50 pct of the Canadian asbestos output. Production from the Canadian serpentine belt is the chrysotile asbestos, which is considered the best available for spinning. Consumers in the United States prefer the clean, fine fibers of the Canadian chrysotile of the type produced by the Jeffrey mine. Mining In 1881, when the mine was first opened, all work, including drilling, was done by hand. The deposit, located on a hillside, was first worked as a sidehill cut by hand drilling 15-ft holes and blasting with black powder. The fiber was chiselled from the broken rock. Hand derricks, later powered by horses, were used to raise the rock as the pit deepened. Eventually, the pit became so deep that derricks were, by necessity, replaced by aerial tramways. In the late 1930's, further deepening of the open pit, with the resulting constriction of the pit bottom brought about the need for altering the mining system then in use. The high ratio of overburden to be handled to mill ore mined and the value of surface structures, not company property, that would be destroyed in expanding the area of the pit, definitely indicated vertical rather than horizontal expansion would have to be used. One exception to this was that a small area on company property to north and east of the pit could be opened up. The mining problem then resolved itself into two phases; make the small lateral expansion and as rapidly as possible choose a mining method that would expand the mine vertically. Several methods for vertical expansion were studied and rejected. Methods considered included shrinkage stoping, block caving, glory holing, and various modifications of open workings. Block caving was finally accepted as the most suitable method of underground development. Cost factors and production were important factors in the decision, also, the asbestos mines in the Thetford area were already having success with this method. Original plans provided for the lateral expansion of the open mine where possible and beginning the underground operation. This program was based on the open pit being worked out in 1954, with the underground development and production gradually increasing until the open mine was depleted. In 1949, the plan was changed to allow underground development to progress at maximum so that underground output would be 550 tons per hr by 1951. Any deficit in ore would be mined from the open pit. This change permitted extending the life of the open pit through 1964 and in this time would make available a large quantity of readily attained ore. Block Caving at The Jeffrey Mine Plans for the underground operation were formulated on a 12,000-ton-per-day basis, and the adaptability of block caving methods to high production presented a desirable situation. As shown in the main-haulage plan, a continuous loop was laid out for smooth operation of the underground railroad from the loading points to the underground crusher. A feature encountered at the Jeffrey mine, as well as other asbestos mines using caving methods, is the large size of caved material, requiring that ore be crushed before hoisting.

Jan 1, 1952

By H. P. Allen

The Achotla mill of the Cia. Minera de Penoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1939

By H. P. Allen

The Achotla mill of the Cia. Minera de Penoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1939

By W. L. Saunders

(New Haven Meeting, February, 1909.) This paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the heading-and-bench system. Much de-pends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading. In mines, the tunnels, drifts, cross-cuts, adits, etc., are usually of small diameter, hence the driving of headings applies to completed tunnels in minim-work, except, of course, in cases like drainage-tunnels and main entries leading into coal-mines, where conditions call for tunnels of large diameter, approximating those driven for railway-service. In building aqueducts the tunnels are driven from 6 to 8 ft. in diameter up to 15 or 20 ft., while in railway-service the dimensions vary from 18 to 30 ft. in diameter. There is no department of rock-excavation so difficult as that of heading-driving. This work. also belongs to the most expensive class in rock-excavation. A heading is driven .directly in the solid. There are no lines of lesser resistance towards which to direct the energy of the blast, but. the material must be blown out by main force. The completion of the heading simplifies all the rest of the work of excavation. It is easy, for instance, to enlarge a heading either from above, below or oil the sides, by breaking towards the open face through holes approximately at right angles to the axis of the heading; or the enlargement sometimes takes place by holes driven outside

Apr 1, 1909

By Harry E. Krumlauf

The year 1957 was one of declining metal price and production. Many lead-zinc-copper mines were forced to close, and the remaining mines limited production to stay more in line with demand. High cost of labor, supplies, and equipment and high taxes aggravated the situation. Some operators postponed or abandoned expansion programs because of uncertain economic conditions. Output was curtailed by elimination of over- time employment and reduction of the working force. The number of employes laid off was small- reduction in the labor force was accomplished by not replacing those who left a company's employ.

Jan 2, 1958

By William R. Webster

I have continued the investigation of the Pottstown Iron Com pany's basic Bessemer keel plates on the line referred to in my paper of last October (Trans., xxi., 766)) and have added a study of the hardening effects of sulphur, which were not taken into account at that time. The results are so encouraging that I now give them in full. For some months we have graded all the steel at these works by the table given in my former paper, and checked the grading by the forging-tests as described in the paper of Mr. Joseph Hartshorne, read at the same meeting (Trans., xxi., 748). The steel thus graded was bloomed for the plate orders. Then one slab was rolled into a plate for the order, and a tension-test was made of this plate. By the result of this tension-test we were guided in rolling the balance of the heat. Out of several hundred heats graded in this manner, 95 per cent. met the requirements of the orders in every respect, and were accepted; but these results will no doubt be improved upon, when the influence of sulphur is also considered.. The hardening effect of sulphur seems to be about 500 pounds per each .01 per cent. of increase. In the table accompanying the pres ent paper, the ultimate strength with .06.5 per cent. sulphur agrees with the old table where sulphur was not considered; that is, for all steels with less than .065 per cent. sulphur we now get lower re sults, and for those with more sulphur, higher results. Making this allowance for sulphur, the assumed ultimate strength of a 3/8-inch plate of pure iron is reduced from 38,000 pounds per square inch to 34,750 pounds. With this as a basis, I have constructed my new table, giving each of the elements, carbon, phosphorus and manganese the same hardening effect as before, to wit : Carbon is credited with a constant effect of 800 pounds per each, 0.01 per cent. Phosphorus shows greater effect in high-carbon than in low-carbon steels. For 0.07 and 0.08 C, it has about the same effect as carbon, that is, 800 pounds for each .01 P. This increases to 1500 pounds per .01 P in 0.15 C steel, or nearly twice the effect of carbon. This

Jan 1, 1894