Search Documents

By C. F. Gleeson, D. G. Sheehan

"The results of humus and overburden geochemical surveys over the Doyon, Bousquet and Page-Williams gold ore deposits are presented.These studies show that humus sampling for gold gives negative results over the Doyon deposit. The lack of response is probably caused by the presence of 1 m of relatively impermeable glaciolacustrine clay and silt that overlies 1 m to 2 m of till over the surface expression of the ore zone. By contrast, positive responses for gold occur in humus samples over the Page Williams A and C gold deposits. The ""A"" ore zone is covered by several metres of exotic calcareous till over 0.5 m to 1 m of older, locally derived till. Anomalous values for gold in humus range from 10 to 35 ppb over the orebody. Overburden over the ""C"" ore zones is much thinner, generally it consists of less than 2 m of sandy till. Trenching humus anomalies that range from 10 to 1360ppb Au uncovered the gold mineralization. The geochemical dispersal trains in till from the Doyon orebody and the Page-Williams ""A"" zone are relatively short (i.e. less than 200 m) because both deposits occur in the lee of bedrock highs that shielded them from extensive glacial quarrying. Dispersal trains from all three pyritic gold deposits can be defined using either the fine fraction or heavy mineral fraction of the till.The intensity of the gold in till anomalies over the ore zones is variable. Therefore, it would be misleading to attach rigid significant threshold gold values to overburden drilling results. Each case must be evaluated based on bedrock topography, sample density, overburden type, thickness of till, as well as size, type and orientation of the target exposed to glacial erosion."

Jan 1, 1987

By Robinson KJ

Education in Australia now has to respond to a very wide political and policy agenda. The political emphasis is upon increasing participation and retention rates with a view to greater graduation rates in `high-tech' disciplines. There is an implied linkage between `education' and `economic well-being'. Our argument is that equalitarianism in education tends towards mediocrity. In this context many Geoscience educators view the future with pessimism. The argument is that science has been `sold short' and needs revitalising. We contend that Geoscience coursework should be a feature of both secondary and tertiary education in Australia. To this end we propose six policy initiatives to increase the content of Geoscience in education programmes.

Jan 1, 1989

By John H. Weigand, Stephen V. Crum

"VIBRONICS, INC. instrumented and monitored a residential structure for response to,blasting at aMidwestern surface coal operation. The residence was owned by the mining company and was extremely close to the operation. Blasting was conducted within 120 feet (36.5 meters) of the test structure. Up to seventeen (17), four (4)-channel seismographs were used during the monitoring period. The basement walls and floor were monitored. VIBRONICS, INC. also monitored a brick chimney in the basement and attic. Structural responses were then compared to outside vibration measurements taken in the soil near the foundation."

Jan 1, 1998

By Douglas W. Christie

Deep foundations in Washington, DC have played a role in the city?s development since the 19th century. Designers of government and commercial buildings sought deep foundations initially to minimize settlement of structures. As the western portion of the National Mall was made by filling in portions of the Potomac River, numerous memorials and monuments on the Mall required deep foundations. In recent years deep foundations have been used to allow underground construction for various reasons. Commercial developers have sought to maximize the use of sites by developing below-grade space for parking to meet code requirements and offset the limits on building heights. Underground museum and gallery space has been constructed to expand public space while preserving open space above grade. Access and security concerns have prompted the design of underground visitor centers rather than above-grade structures.

Jan 1, 2006

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumedmetabolic rate of 325W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ?Tgi and ?HR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ?Tgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

Nov 8, 2019

Jan 1, 1993

By J. E. Nesset, S. R. Rao, J. A. Finch

"For base metal sulphides, iron rejection starts in mineral processing. This review focuses on changes in plant practice specifically to improve iron sulphide rejection by control of contaminant ion effects and discusses selected general innovations in mineral processing that can be expected to play a role. One group of changes to control contaminant ions is in size reduction (the use of stage grinding and inert stirred milling) and another is in system chemistry (order of reagent addition and exploitation of the flexibility of sulphoxy reagents). Plant examples illustrate the successes, indicating that there are several options available. The general innovations start by considering the new tools for measuring gas dispersion properties and quantifying froth characteristics by imaging. Examples of their application to improve concentrate quality illustrate the potential. Other innovations stress adapting geostatistics to model variation in milling and flotation response to provide feed forward control and rigorous application of statistical experimental methodology in plant test work. An example from one concentrator shows improvements in concentrate quality from application of basic principles can be impressive.INTRODUCTIONThe more iron control (rejection) that can be accomplished in mineral processing the lower the subsequent metal extraction costs and environmental implications of iron disposal, particularly in hydrometallurgical processes. Iron rejection has been a contributing target to periodic attempts to apply mineral processing to nickel laterites and bauxites but the prime application is control of pyrite and pyrrhotite (iron sulphides) in the treatment of sulphide ores by flotation. In this paper some new concepts and innovations introduced in sulphide flotation plants over the past ten years or so (i.e., since a previous review [1]) will be outlined with examples of how they have contributed to improved “iron control”.To increase rejection of iron minerals, first the recovery mechanism should be understood. There are four principal ones, two physical in origin: 1, via locked particles (i.e., flotation of composite particles due to insufficient size reduction to liberate the minerals) and 2, through entrainment in the water reporting to the float product (an unselective process); and two originating from a response to the system chemistry: 1, true flotation (i.e., iron sulphides becoming hydrophobic) and 2, as a result of iron sulphides forming aggregates with hydrophobic particles (e.g., ”slime” coatings). There has been considerable effort to diagnose which of these dominates iron sulphide recovery; in many cases it is due to “chemistry”, in particular true flotation. The flotation effect often appears related to contamination by metal ions [1]. This can reduce selectivity in two ways: 1, metal ion species may activate iron sulphides, or 2, cause general depression which demands more vigorous flotation conditions (e.g., additional collector) with consequent loss of selectivity. This is where the review will start, by considering ways to control contaminant ions."

Jan 1, 2007

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,500 tons of ore per day with an average gold grade of 0.34 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, a long-hole stope and cut-and-fill mining methods are used at the deposits which are divided into several mining zones. Cemented rock fill (CRF) is used as the backfill in the open stope. CRF design includes the aggregate design, the ratio of cement and fly ash design, and strengths for the long-hole stope and cut-and-fill. In the aggregate design, the particle size distribution is one of the most influential aggregate characteristics in determining how it will perform as a basic backfill material. Gradation helps determine durability, porosity, cement and water requirements, strength, and shrinkage. To cut the backfill cost, fly ash usually is added into the binder to replace some part of cement. However, adding fly ash can affect the strength of the backfill. The reasonable percentage of fly ash is also important for making a good and low cost backfill. Based on the different mining method, the different backfill with different strength is designed. A systematic quality control procedure for aggregate and backfill is followed. After four yeas application, CRF system in Leeville achieved very good results.

Jan 1, 2011

The stratigraphy of the Western Coalfield is briefly reviewed and the important units of the Lithgow Coal Measures, particularly the coal seams, are defined. The possibility of coal measures of Tomago age ocurring near the edges of the Sydney Basin is discussed onpresent evidence.Using data obtained from unpublished drilling records, detailed structural, isopachous and lithofaeies maps have been drawn. These show that the structure of the coal basin has been influenced by the underlying basement in many ways.The prominent jointing in the overlying Triassic sandstones is discussed in relation to jointing in the coal measure sediments.It is concluded that in addition to the general knowledge obtained with respect to the coal basin, useful information regarding coal quality and quantity can be gained by the study of broader sedimentary and structural features.INTRODUCTIONThe term "Western Coalfield" covers approximately the area from Katoomba to Rylstone, together with the smaller, separate Ulan area (Fig. 1). The area studied is part of the great sedimentary Sydney basin named by Osborne (1948). The first discovery of coal in Sitlt in the area was made in 1824 by Andrew Brown, although George Bass noted the presence of coal float in the Grose River in 1797. Production is recorded from the Western Coalfield in 1838 but mining was intermittent until 1868 when mines in the Lithgowvalley (producing coal from the Lithgow Seam) came into production. In 1882 the Katoomba Seam was first worked at Katoomba.The work of J. E. Carne (1903, 1908) defined the limits of the Coal Measure sediments and also contributed a great amount of valuable detailed information about the region.

Jan 1, 1960

By Yates C, Gillie E. W, Finucane K. J

During the year 1940 a complete investigation was made of the whole of the stoping operations throughout the Great Boulder Mine and, as a result, it was decided to convert some of the existing shrinkage stopes into cut-and-fill stopes, and also to mine many of the more recently developed ore blocks by the latter method. The necessity for filling was due primarily to the structure of the ore blocks, the character of the walls and possible excessive dilution, but was influenced also by the grade of the ore-block and by the fact that cleaner mining can be carried out by cut-and-fill stoping.The comparatively few cut-and-fill stopes in operation prior to 1940 had been filled mainly with waste rock from development work, but as the amount of this material available, or likely to become available, would have been wholly inadequate for future operations, it was proposed to construct a system of passes to supply filling material from the surface.Owing to the distribution of the stopes, no central pass or system of passes could be devised which would service all the stopes satisfactorily.However, work was commenced on two passes, one designed to service the cut-and-fill stopes in the Eastern Section of the mine, and another to service those in the Western Section. It was realised that these passes could serve only a small proportion of the total number of Stopes (Figs. 1 and 2). During the progress of this work experiments were undertaken to test the possibility of using filtered tailings underground as an adjunct to the above scheme, but for various reasons these were only partially completed.Early in 1942 it was suggested by the Mill Superintendent that an attempt be made to fill with wet classified flotation tailings as practised at Mt. Lyell in Tasmania and at the Triton Mine at Reedy, West Australia. For the purpose of testing this, an experimental stope was prepared on the 309-ft. level, "X" Lode. This was 100 feet long and averaged 4 feet in width. Water-tight rearings were built at each end of the stope and waste rock fill was spread to a height of 6 to 8 feet above the timber. Used filter cloths were laid on top of the fill and brought a few feet, up the walls of the stope. A two-inch victaulic drainage line was then placed in position, the end passing through a hole in one of the bearings and thence to a sump. In the central portion of the stope two vertical pipes were brought up from this line. These were bored with one-inch holes staggered on opposite sides of the pipe, the vertical interval between each hole being one inch. The holes were then stopped with...

Jan 1, 1945

Further evidence is presented as to the widespread occurrence of Thiobacillus ferrooxidans in nature in association with sulphide minerals. Leaching rates are discussed in terms of the effect of environmental parameters, particularly Eh and pH, on the bacterial process.The methods used to investigate leaching phenomena are described and the advantages and limitations of each method are discussed. A theoretical treatment of the bacterial leaching process is given which indicates that the optimum conditions arrived at by traditional methods are compatible with those deduced from consideration of the mathematics of continuous culture and thermodynamics

Jan 1, 1968

By G. Zaitsev

In mining and mineral processing, ammonium and nitrate from residues of explosives and other sources are discharged to the aquatic environment. Nitrogenous compounds in mine water can adversely affect the aquatic environment. The aim of this work was to study the biological removal of nitrate from cold inorganic mine water at the pilot-scale in an operating underground mine. Seven-months pilot testing on biological removal of nitrate from inorganic mine water was successfully performed in denitrifying fixed-bed biofilm reactors. The feed to denitrification bioreactors contained 11 mg NO3--N/L. Methanol was added as an external carbon source to the denitrifying bio-reactor since the inorganic mine water contained only traces of organic compounds (<CODCr (50 mgO2/L). Nitrate removal reached 75 g NO3--N/m3/d with removal efficiencies above 95% at temperature below 4°C. Thus, removal of explosives-residues from cold inorganic mine water was shown in pilot-scale biofilm reactors.

Jan 1, 2014

By Randy Vranes

Sophisticated information technology, quality management systems and a commitment to the environment has allowed Solutia’s Soda Springs phosphate mine and elemental phosphorus plant to reduce operating costs, improve product quality and contribute to the sustainable development of Idaho’s industrial minerals. Soda Springs background The Soda Springs phosphate mine and plant is a joint venture between Monsanto and its operating partner, Solutia Inc. The operation is based in southeastern Idaho in the Western Phosphate Field. The plant is located about 275 km (170 miles) northeast of Salt Lake City, UT and about 4 km (2.5 miles) north of the town of Soda Springs.

Jan 1, 1999

By N. Gatelier, T. You, J. C. Kandel

ABSTRACT: Underground hydrocarbons storage is a very specific domain for the designer. He is usually free to adjust the section, shape and layout to cope with the geological and geotechnical conditions. This paper presents a panorama of the geotechnical design of mined underground storage caverns, then lists a number of uncommon features encountered in a storage excavated in Sydney, Australia, the Elgas LPG project that had to face major non-isotropic conditions with numerous local variations, impacting on the achievement of the design profiles. Changes in geotechnical design methodology and practice are examined through this project, now in operation, which will have lasted altogether almost ten years. KEY WORDS: underground storage, geotechnical engineering, stability, methodology, design. ZUSAMMENFASSUNG: Die untertaegige Speicherung von Kohlenwasserstoffen unterliegt in der Planung sehr spezifischen Bedingungen. Der planende Ingenieur hat bei der Dimensionierung und Formgebung der Speicherhohlraeume gewisse Freiheiten, muss jedoch vorgefundene geologische und geotechnische Bedingungen beruecksichtigen. Der vorliegende Beitrag gibt zunaechst einen allgemeinen Ueberblick ueber die geotechnische Planung von bergmaennisch aufgefahrenen Speicherhhohlraeumen. Darueber hinaus werden Besonderheiten betrachtet, mit denen das Elgas LPG-Speicherprojekt in einer bergmaennisch aufgefahrenen Kaverne in Sydney, Australien konfrontiert war. Hierbei ging es um die Beruecksichtigung anisotroper Bedingungen mit zusaetzlichen Heterogenitaeten im Gestein und den daraus erwachsenden Schwierigkeiten, die geplante Hohlraumform zu verwirklichen. Ueber einen Zeitraum von fast 10 Jahren, in denen das jetzt in Betrieb befindliche Projekt unterschiedliche Betriebsphasen durchlaufen hat, wurden verschiedene geotechnische Entwurfsverfahren auf ihre Anwendbarkeit geprueft. SCHLUESSELWOERTER: Untergrundspeicherung, Geotechnik, Stabilitaet, Entwurfsverfahren, Planung. RESUME : Le stockage souterrain d’hydrocarbures est un domaine très spécifique pour le concepteur, car celui-ci dispose d&apos;une large liberté pour adapter les sections, les formes et les implantations aux conditions géologiques et géotechniques de l’environnement choisi. Après un panorama de la conception géotechnique des stockages souterrains d’hydrocarbures par la méthode dite des cavités minées, l’accent sera mis sur un certain nombre de particularités rencontrées lors du projet de stockage de GPL de Elgas à Sydney en Australie, creusé dans de très fortes conditions d’anisotropie du massif rocheux, avec de nombreuses variations locales et toutes les implications que cela peut avoir sur le maintien des formes. L’évolution des approches méthodologiques géotechniques durant la dizaine d&apos;années de développement de ce projet depuis les premières études jusqu&apos;à l&apos;exploitation actuelle est également présentée. MOTS-CLEFS : stockage souterrain, géotechnique, stabilité, méthode, conception.

Jan 1, 2003

By Warren E. Morrison

Stimulated by 4 years of continuous economic growth without inflation, demand for energy in the United States reached an alltime high in 1964. Total value of production of goods and services (gross national product--GNP) for the year was $629 billion, an increase of 6.8 percent from 1963. Allowing for price changes based on 1958 dollars, the gain in real terms was 5 percent. In 1964 the Federal Reserve Board Index of Industrial Production stood at 132, a rise of 6.2 percent. With the impetus provided by personal income and corporate tax reductions during the year, aggregate wages, profits, and consumption reached record levels. Even the persistent balance of payments problem improved. Against this background the national consumption of commercial energy increased 4.2 percent. Energy needs continued to be met largely from domestic resources with imports, mainly crude petroleum and refined petroleum products, accounting for but 7 percent of the total. Mineral energy resources, namely gas, coal, and petroleum, contributed 96 percent of the input of energy into the economy during the year. The remaining 4 percent came from hydropower and nuclear power.

Jan 1, 1965

By L. M. Pidgeon

"Part I. - PrinciplesIntroductionIf the oxides of the metals are listed in decreasing order of the magnitude of their heats of formation, the list appearing in Table 1 will be formed. It will be apparent at once that this is essentially the well-known electrochemical series (Table li). The metals at the bottom of the list exhibit great stability and are attacked only by the most violent of chemical reagents. Higher on the list, the metals become more reactive until, at the head of the list, the metals lithium and calcium are unstable in moist air.The reactive metals to be considered lie above manganese. In this group will be found familiar and abundant metals such as aluminium and magnesium, the unfamiliar yet abundant metal titanium, the rare and mysterious metal beryllium, and others of greater or less interest.While these metals exhibit properties as unlike as those of uranium and magnesium, they have in common a specialized and difficult extractive metallurgy. They form compounds of great stability, and their reduction is to varying degrees difficult. The position of a metal in Table 1 (and more particu1arly its position in the free energy column) gives a numerical value to this property.Oxides with low free energies of formation may be reduced with great ease; thus silver and mercury may be produced from their oxides by simple heating in air.Lead, iron, and zinc may be separated from their oxides by heating with carbon to moderate temperatures. Magnesium oxide, on the other hand, .requires a high temperature and very special conditions before it will yield magnesium metal."

Jan 1, 1950

By H. S. Sichel, W. J. Kleingeld, C. E. Dohm

A model of ore value distributions is presented that is the culmination of a statistical approach rather than simply a model that has been successfully applied to the evaluation of ore reserves. Detailed geological and physical observations based on large sampling data sets have been used to support the statistical modelling. Fundamental to the modelling process is the concept that the occurrence of a given grade value in space is a function not only of the presence of the mineral but also of the fact that it is associated with a specific trapping mechanism. The concepts have been specifically applied to gold mineralisation

Aug 1, 1995

By D. DeGagne, E. De Souza, J. F. Archibald

This paper describes the potential use of anew agent material for backfill consolidation, ground waste glass, to be used as partial replacement of Portland cement fractions within backfill. Significant fractions of commercial and residential silica glass production is currently utilized as waste landfill and must be disposed of at high cost and with no foreseeable environ-mental benefit. This paper also demonstrates that waste glass materials could be effectively recycled as backfill additives, and that a significant, large and stable source of additive supply, currently land filled, can be developed. This new application will generate added value for such materials, serve to promote positive environ-mental stewardship and satisfy engineering sup-port requirements in mines.

Jan 1, 1997

By S. B. Bealko

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities, and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies including a fire or explosion, a massive roof collapse, mine inundations, or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life, and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006