Search Documents

By Jeff Whyatt

Deformation of underground salt, trona and potash mines is generally time dependent, providing for gradual adjustment of strata to mining induced stresses. Time dependence can allow for higher extraction ratios provided eventual failure can be tolerated. However, this eventual failure can be violent if creep deformation can shift stress and potential energy to strong, brittle geologic units. The mine failure case studies reviewed here illustrate this process. Yield pillars and defects in bridging strata figure prominently in these cases. Yield pillars provide local and temporary support to the roof, temporarily delaying the cave; and allowing extraction ratios and overburden spans to increase beyond the long term capacity of overlying strata. Defects (faults, voids, thinning) of strong overburden strata reduce the critical span, sometimes to less than panel width. Analyses of many of these cases have focused on a cascading pillar failure mechanism, but recent work and this review point to failure of strong overburden strata as the essential element. The suddenness of failure and attendant seismic events pose hazards to miners and, in some cases, to those on the surface. Characterizing these failures is a first step towards recognizing and managing the risk of catastrophic collapse in underground mines.

Jan 1, 2008

By K. Nasrallah

"The Dumont deposit is a large (1,179 Mt proven and probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the project from a scoping study in 2010 through to completing the feasibility study in July 2013.The Dumont deposit in a nickel deposit with the recoverable nickel contained in three minerals; pentlandite, haezlewoodite and awaruite. The minerals are recovered by a combination of flotation and magnetic separation. Over the course of the studies many flowsheet design decisions and changes were made. This paper outlines an overview of the project, flowsheet design including the comminution circuit, desliming and awaruite recovery. The overall resulting flowsheet that was used for the feasibility study is then presented along with the confirmatory locked cycle testing that showed the feasibility design basis was able to produce the predicted concentrate grade and recovery.IntroductionRoyal Nickel Corporation (RNC) is a mineral resource company headquartered in Toronto, Canada, primarily focused on the exploration, evaluation, development and acquisition of base metal and platinum group metal properties. RNC's principal asset is the Dumont Nickel project (Dumont project) located in the established Abitibi mining camp, 25 km northwest of Amos, Quebec. RNC acquired a 100% interest in the Dumont property in 2007. The mineral claims covering the Dumont deposit are currently held 98% by RNC and 2% by Ressources Québec.The Dumont project is located in the province of Quebec in the municipalities of Launay and Trécesson approximately 25 km by road northwest of the city of Amos, 60 km northeast of the industrial and mining city of Rouyn-Noranda and 70 km northwest of the city of Val d’Or."

Jan 1, 2016

By G. M. Schwartz

THERE has been considerable controversy regarding the structure and mineral constituents produced when iron ore is sintered. This investigation was undertaken in order to establish the fundamental reactions that take place in the sintering process by determining the nature of the resulting minerals. The writer's immediate interest in the subject arose mainly from the request of E. W. Davis for information based on a microscopic study of sinter submitted by him in May, 1926. In the author's preliminary work, samples of iron-ore sinter were secured from the Minnesota School of Mines Experiment Station and from commercial plants. These were polished by the usual methods for polishing opaque ores. In order to study these surfaces satisfactorily, it is necessary to magnify them rather highly, a range from 100 to 1000 dia. being used. For the higher magnifications oil-immersion lenses and an intense source of light are necessary. After the preliminary study had shown the problems involved, a series of small samples were sintered under carefully controlled conditions and with analyzed materials. Variations in the relative amounts of ore, coal and water were made in order to study the effect of each constituent. The attempt has been to arrive at a clearer understanding of the sintering process and the reactions involved without reference to any preconceived notion as to sinter. It is clear that the study of polished surfaces has yielded results not possible with thin sections alone. The thin sections made in this work were found unsatisfactory at magnification greater than 75, whereas magnifications of 1000 were easily studied with reflected light on carefully polished surfaces. A rather complete statement of observed facts is made so that the reader may form his own conclusions. The writer's interpretations are suggested.

Jan 1, 1929

By Charles E. Wait

It is said by some that the occurrence of a deposit of sulphide of antimony in Southwestern Arkansas has been known for fifteen or twenty years. Whether or not such is the case I am not prepared to say, but I am not able to find any record of such a discovery, or any analysis of antimony ore obtained from that section, published at so early a period. The present discoveries, that seem to be attracting some attention, date back to the winter of 1873-74. At that time a vein of ore was found by Mr. Robert Wolf, in honor of whom the vein was named, and still is called, "the Wolf lode." At the time of the discovery the ore was unknown to the prospector, and its composition was not thoroughly understood in that locality until samples were sent to several analytical chemists, who pronounced it sulphide of antimony—stibnite. Since the discovery of this ore there have been three mines opened, and a number of interesting minerals of the antimonial series have been found. I have had an unusually good opportunity to collect specimens from these mines; and it is owing to the constant inquiry concerning the character of these ores that I have collected for publication the results of quite a number of analyses, sufficient I trust to clearly point out their composition. This is one of the few localities in the United States where antimony ore is found in workable quantities ; I say workable quantities, because two different shipments of ore have been made to English reduction works, and in both cases excellent returns were made. The discovery of these deposits will, it is hoped, give rise to a prosperous and remunerative industry at no distant day, and when fully developed they may yield ore in sufficient quantity to supply the regulus for the home demand, thus adding wealth not only to those interested, but also to the State of Arkansas. The three mines are situated in the northern part of Sevier County, and may be reached by the St. Louis, Iron Mountain and Southern Railway to Fulton, thence by wagon-road to Columbus, Nashville, Centre Point, and to the mines. During most seasons of the year the

Jan 1, 1880

A discussion on simulation tools to aid the development of robotics platforms is presented. The focus of the work is towards mining robotics platforms where operations are typically in unstructured, unpredictable environments and a high degree of dependability in their operations is required. It is argued that a test-based development approach leads to more robust solutions and faster development cycles than traditional single-track field-only development and that the key enabling technology for this development paradigm is the judicious use of simulation tools. The future direction of simulation for use in online applications such as active planning and as a means to assist tele-operation in high latency communication applications is also brief y considered together with the requirements for a useful simulation environment in terms of the simulator architecture. Finally, a case study is presented on the application of the discussed methodologies to an unmanned ground vehicle (UGV) for earth-moving tasks, which is being developed in an accelerated time frame with a transient development team.

Dec 6, 2010

By C. Crussard, R. Tamhankar

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers accord-ing to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Gerhurd Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Staff Coordinator, James J. Burke THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Past-President; John Chiprnan, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman; Dennis Carney, John Chip-man, J. C. Fulton, J. H. Hollomon, H. H. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and D. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman, F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham, .Jr., Robert F. Hehemonn, R. I. Jaffee, F. E. Jaumot, Jr., Irving R. Kramer, A. J. Lena, Harold Margolin, C. J. McHorgue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alan U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B. King, F. C. Langenberg, W. 0. Philbrook, and T. 0. Winkler. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AIME members. Single copies, $4.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AIME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts... Second class postage paid at New Yark, N. Y., and Ann Arbor, Mich. Volume 212, Number 6.

Jan 1, 1959

By Alvin Schallis

Of all the uses for dolomite that depend on its magnesia content, perhaps the most important is its use in basic refractories. The quantities of dolomite (including both that used as crude and that calcined before use) sold or used for refractory purposes by producers in the United States for 1920-41, inclusive, are shown in figure 1. As can be seen from the chart, the utilization of dolomite as a basic refractory is far from new; it was, in fact, the first basic refractory used extensively in open-hearth steel furnaces. After large deposits of magnesite were opened in Austria-Hungary, the use of dolomite in the open hearth declined somewhat, only to be actively revived during the World War of 1914 to 1918, when supplies from Austria were shut off. The use of dolomite as a refractory in the steel industry again declined slightly for a brief period after the Armistice, but subsequently its use has tended steadily to increase, latest statistics indicating that more dead-burned dolomite is used per ton of open-hearth steel now than during the World War of 1914 to 1918. Despite fluctuations in consumption, dolomite has continued to be by far the most widely used basic refractory material. The following table, showing the quantities of basic refractories consumed in the manufacture of steel, the principal outlet, indicates the relative importance of dolomite. The chief reason for the widespread use of dolomite as a basic refractory is its relatively low cost. Its abundance and the proximity of the deposits to the steel industry (see fig. 2) afford every incentive to enhance the desirable physical properties of dolomite refractories and to ameliorate certain of their less desirable characteristics. The present emergency, with its huge demands upon the steel industry, has lent further impetus to the work of improving dolomite refractories.

Jan 1, 1942

By Jean-Marie Fecteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET?s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialised in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET?s program in mechanisation and automation for narrow vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies (Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow vein mining industry. Several important impacts of this project will be monitored. Specifically, a database of methods and equipment used in narrow vein mining is being developed. A key thrust is to identify operators? needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The main problems identified following meetings with mine operators are described with a few elements of solution and the Web site created for the broadcast of the results is presented.

Oct 1, 2001

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By C. W. Whitten

Iron ore deposits in south-central Missouri have emerged as a possible resource for the rare-earth elements. The Pea Ridge Iron Mine is one such deposit. Rare-earth minerals at the Pea Ridge Iron Mine are contained in breccia pipes consisting primarily of silicon oxides and feldspars. These pipes extend up through the magnetite ore body and appear to be alterations and replacement of earlier hematite. The mineralogy of these pipes is very complex and varied, which could complicate the concentration and extraction of the rare-earth minerals. This U.S. Bureau of Mines !eport represents a study by characterization of the mineral phases to assess the amenability and development of concentration and extraction techniques. Previous characterization of rare-earth minerals has been mainly by transmitted light microscopy. This method along with reflected light microscopy, scanning electron microscopy, and X-ray diffraction was used to identify and characterize the rare-earth and associated minerals. The minerals identified were the major ore minerals, magnetite and hematite; the rare-earth phosphates, monazite and xenotime; the rare-earth silicate, allanite; the minor associated minerals, cassiterite, pyrite, and apatite; and the gangue minerals, feldspar, quartz, and actinolite.

Jan 1, 1990

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2004

By Laura Bustemante, Bruce Vandenberg, Fred Huettig

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to 1000 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the KineView 1256P system and compare these with the analogous aspects of fii based cameras.

Jan 1, 1998

By Rossiter W. Raymond

(Canal Zone Meeting, November, 1910.) THE death of Professor Blake removes the oldest of American economic geologists and mining engineers, and deprives this Institute of one of its, earliest and most illustrious members. To many of us it brings a personal loss also, the loss of a friend. William Phipps Blake was born June 21, 1826, in New York City. -His father, Elihu Blake, was a surgeon-dentist of eminence, a direct descendant of William Blake, who settled in the Massachusetts Bay Colony about 1630. He was prepared for college at private schools in New York, and entered the Sheffield School of Yale, where he was graduated as Ph.B. in the chemical course, class of 1852, the first graduating-class of the institution. In the same year he became chemist and mineralogist of the New Jersey Zinc Co., and chemist of chemical works at Baltimore, Md. In 1853, lie started the Department of Mineralogy of the World's Fair at New York City. In 1854, 1855 and 1856, he was mineralogist and geologist of the United States Pacific Railroad Surveys of Williamson, Pope, and Whipple, and for the War Department at Washington. His writings, during this period comprise reports on the geology and mineralogy of California and other parts of the Southwest, and constitute well nigh the earliest scientific accounts of the regions described. One of them. was a translation of the Resume and Field Notes of Jules Marcou, of Whipple's expedition. From 1856 to 1859, he was engaged in explorations of the geology and mineral deposits of North Carolina, :and other parts of the country. In 1859, he became editor and proprietor of The Mining Magazine. This was a monthly periodical, founded in 1853 by W. J. Tenny, who conducted it until 1858, when it passed into the hands of Thomas McElrath, a New York publisher, and appeared in May of that year as The Mining and Statistic Magazine, with the name of

Sep 1, 1910

By Vincent Jue

In December 2009, the Italian High Speed Rail Network AV began running over the full 1000 km system length from Turin, at the foothills of the Alps to Salerno, on the seacoast south of the volcano Mt. Vesuvius. It runs through Alpine rivers, highly seismic active zones, mountains, river plains, and through some of the most densely populated areas in Europe as well as some of its most expensive real estate. The Italian High Speed Network?s technical/economic constraints and its regulatory/socio-environmental concerns well may mirror similar obstacles set to confront the nascent California High Speed Rail Program. The two types of constraints must be dealt with together to reach the best construction solution. It is estimated that more than 20% of Italian High Speed Rail Network costs were spent on ground engineering including over 150 km of tunnels, 200 km of viaducts and bridges and 650 km of embankments and trenches. However, it also is estimated that 25% of costs were spent on social and environmental integration of the new rail lines including over 6 square miles of green offsets, 160 km of anti-noise walls, and 300 agreements for socio-environmental work. This paper will look at four examples of innovative ground engineering solutions, each with its own intricate set of constraints: ? Foundation system for viaducts across the ?Po? and ?Ticino? rivers. ? Soil consolidation under railway embankments ? Requirement of short tunnels for physical and environmental reasons ? Construction of railway stations in a confined right of way

Jan 1, 2010

By W. L. Hunter

The preparation of coal for the commercial market is a study both varied and wide, and can be viewed from many angles and in different ways. This short paper can but touch upon the subject and is intended to discuss briefly preparation plants which in some cases would seem to be quite inadequate. The conditions confronting most operators are similar, inasmuch as the existing plants were not built specifically to prepare a product for the market of today, but rather of yesterday. The tremendous strides made in the field of combustion in recent years require that the product be of the highest grade procurable, and in a glutted and somewhat restricted market the buyer may be more pernickety than otherwise. These would appear to be the conditions of today. Where a mine is operated individually, better all-round results seem more readily procurable than in a consolidated effort where so many different conditions are sure to arise demanding cognizance, and in many cases requiring to be incorporated in the scheme of things. In the case of a number of mines being administered to form a central source, that source not having had anything to do with the bringing into being of the institutions over which it presides, we find some of the mines well equipped with facilities to properly screen and load the coal, while in others the facilities are not so good, but are doing their share towards delivering a product that will pass muster and in such quantities that they can be counted on.

Jan 1, 1930

By L Abrahamsson

This paper describes results from a gender study for a new mine in Pajala, a small community in northern Sweden. Using a gender perspective, the study examines migration, education, local culture, the labour market, and work organisation as problems and opportunities in the regional context for the planned mine. The most obvious ‘gender issue’ for the Swedish mining industry is the very low percentage of employed women, which is even lower among mining workers. To recruit the best people, a company actively needs to attract both women and men; however, the mining companies find it difficult to recruit women as cultural, labour market and educational traditions as well as the mining companies’ own cultures often make it difficult for women to find work in the mining industry.The Torneå river valley, the region surrounding Pajala, has a gender-segregated labour market and gender-stereotyped culture and few young women live in this traditional and oldish region. Many young people leave the region and this is especially true for women. Compared to the rest of Sweden, there is a low educational level, especially among the men. In the mining companies, as in many other male homosocial workplaces, the workplace culture has strong connections to a certain type of traditional masculinity (laddishness, a kind of ‘macho-style’) and for a long time this has excluded women. ‘Gender’, however, is not only a question of recruiting women to a male-dominated industry. An organisation that discriminates according to gender can become inflexible, hindering communication, learning, innovations and change processes. In mining companies, this can manifest itself in hesitant attitudes among the miners about safety as well as organisational and technological development.This study found that companies establishing a presence in this region should develop a strategy for how to deal with and manage the risks and opportunities in the surrounding society (the regional culture) as well as inside the company (the mining culture). This need to be strategic will also be required of future mining companies as they will face higher demands on safety, gender equality, and technology to become modern, efficient and lean organisations.

Nov 22, 2011

By W. A. Calhoun, M. M. Fine

"One of the most important wartime activities of the Bureau of Mines was the search for new sources of mineral necessary to the prosecution of the war. Part of that effort was in the form of metallurgical service extended to other government agencies engaged in purchasing and stock piling some of the more critical and strategic materials.Fluorite was one of the materials stock piled by the Metals Reserve Company. The fluorite was usually in the form of coarse metallurgical con¬centrate purchased in the United States and abroad. The material was stock¬piled to insure an adequate reserve of fluorite for the metallurgical industries. The domestic production of metallurgical fluorite containing a minimum effective calcium fluoride content of 55 percent,4/ however, gradually increased until production was at least equal to consumption. The stock-piled metallurgical fluorite, therefore, soon became a surplus commodity.On the other hand, the supply of acid-grade fluorite, containing a minimum of 97.5 percent calcium fluoride and n maximum of 1.5 percent silica,5/ was never entirely adequate. Increased consumption of acid-grade material in the aluminum, petroleum, and chemical industries kept that material on the critical list during the war.Under the circumstances, it was felt that a study of the possibility of producing acid-grade fluorite from the metallurgical stock piles would be of some benefit to the war effort. Consequently, samples of fluorite from several of the Metals Reserve Company stock piles were tested by the Bureau of Mines at the request of the War Production Board.Two groups of samples were submitted for testing. One consisted of metallurgical fluorite purchased from Mexico and stock-piled in the El Paso and Laredo, Texas, stock piles of the Metals Reserve Company. The second group of samples was from the stock piles at Gila, N. Mex.The sample submitted from the El Paso stock pile consisted of about 5,000 pounds of minus 4-inch material. Mineralogically, the sample consisted of fluorite contaminated by calcite, chert, quartz, and small amounts of iron and alumina. Although some of the fluorite was reasonably free from gangue at minus 1-inch, much of it remained locked in sizes as fine as 65-mesh.The Laredo sample was about 5,000 pounds of material from five different piles. The samples from each stock pile, A to E, inclusive, were analyzed separately to determine whether the grade of the material in the piles varied markedly. As there was little difference in the analyses, the samples were combined in proportion to the tonnage represented to make a composite sample for testing. The composite sample consisted of fluorite with small amounts of quartz, calcite, and barite. Most of the fluorite was the dark-colored, opaque variety. A small amount of iron-oxide staining was present, and traces of muscovite, clay, pyrite, and tourmaline were noted. The quartz was present as crystals in vugs, and as finely disseminated grains in the fluorite. The druzy quartz and the calcite were free at minus 10-mesh, but the disseminated grains, some of which were 1 to 15 microns in size, were not entirely free at minus 270-mesh. A petrographic estimate indicated that 65 percent of the silica was locked in the 150- to 200-mesh."

Jun 1, 1946

By Paolo Toscano, Dave Hall

"This paper discusses the project history, process design and layout of the Rainy River Gold Project mill. The circuit consists of a 55 x 83 primary crusher, 15 MW SAG mill and 15 MW ball mill. Both mills are twin pinion with LSS and VFD drives. A pebble crusher is located in the process plant with bypass and stockpile options. Gravity concentration followed by 30 hours of leach residence, carousel CIP, carbon recovery, cyanide destruction and tails disposal in a 1,428 hectare tailings management area (TMA).The Rainy River Gold Project is located approximately 65 km northwest of Fort Frances in north western Ontario. The project is scheduled to be commissioned and reach commercial production in mid-2017. Expected cost is $US877M and is comprised of an open pit mine, process plant, tailings management area and supporting infrastructure. The process plant is designed to produce gold/silver Dore’ bars.The project has been developed on the following timeline:• 1967 – First exploration• 1994 – 17 zone discovered• 2004 – 433 Zone discovered• 2005 – Rainy River Resources Ltd. purchases property • 2006 - ODM zone discovered• 2007 - Cap Zone discovered• 2008 - First NI-43-101 Resource completed• 2012 - PEA completed & Intrepid Zone discovered• 2013 - New Gold acquires Rainy River Resources• 2014 - Updated feasibility study completed & Environmental Assessment report submitted• 2015 - Detailed Engineering >95% complete, EA approved and construction commencesThe property is accessed by provincial highway 600 and is within 17 km of 230 kV power line and railway sidings. Key project criteria are summarized as follows:"

Jan 1, 2016

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011