Search Documents

By A. Roca, G. Ríos, I. Ruíz, M. Cruells

Flash Smelting Furnace (FSF) hot dust-laden is cooled in a waste heat boiler (WHB) and then dedusted in electrostatic precipitators (ESP’s) before being treated, together with the Peirce Smith Converters off-gases, in the sulfuric acid plants for SO2 removal. FSF dust is sulfated by SO2 and O2 in the WHB. Typically, 70% of the dust from the FSF drops in the WHB while the remainder is caught in the ESPs. The collected dust is recycled to the FSF for Cu recovery. Some smelters have developed hydrometallurgical treatments to recover Cu from the dust; impurities, such as As and Bi, are bled as leach plant residues. This paper presents a study (laboratory scale), of leaching the FSF dust, generated in Atlantic Copper Smelter using the weak acid bleed from the gas scrubbing/cooling section (GSCS) of sulfuric acid plants. Leaching was performed with 0.5 mol L-1 sulfuric acid concentration, 60ºC, and a solid/liquid ratio 1/3. After leaching, H2O2 was used for arsenic and iron oxidation. pH was adjusted for precipitation of arsenic and iron as scorodite or as scorodite and arsenical jarosite. The precipitation was carried out at 95ºC during 3-6 h. Liquids after precipitation are suitable for subsequent treatments of electrolysis. INTRODUCTION The copper smelter dusts are usually recirculated totally or partially to the flash furnace. This practice increases the amount of impurities feeding the furnace. Some authors have developed processes for treatment of these materials for copper and zinc recovery and for arsenic, antimony and bismuth inertization. The processes for the treatment of copper smelter dusts can be pyrometallurgical (Yu, 1987; Carter, Vance, Aldridge, Zaw, & Khoe, 1994; Fu, Jiang &Wang, 2000), hydrometallurgical, or mixed processes (Yin et al, 1992; Mulale, Mwema, & Mashala, 1999; Gorai, Jana, & Khan, 2002). Hydrometallurgical processes have been extensively studied and, in some cases, applied to an industrial scale. The most important chemical reagent proposed for leaching the dusts has been sulfuric acid (Roman-Moguel, Plascencia, Pérez, & Garcia, 1995; Gabb, & Evans, 1997; Larouche, 2001; Morales, Cruells, Roca, & Bergó, 2010; Cáceres, Cruells, Morales, & Roca, 2012; Ecometales, 2013; Yang, Fu, Liu, Chen, & Zhang, 2017). Processes developed in alkaline media, and in some cases with the presence of sulfide, have also been carried out (Gabler, & Jones, 1988; Morales, Hevia, & Cifuentes, 2009; Alguacil, Garcia-Diaz, Lopez, Rodriguez, & Alonso, 2013), as well as by using a bioleaching process (Massinaie, Oliazadeh, & Seyed Bagheri, 2006; Bakhtiari, Atashi, Zivdar, Seyedbagheri, & Fazaelipoor, 2011).

Jan 1, 2019

By John C. Stankus, Xiaoting Li

"Underground structures such as square/arch steel sets, king beam structure, etc. are widely used for the roof support in underground mines. In designing and calculating the required carrying capacities of these underground structures, how to identify the potential rock loads on the structures over long term is a challenging question for ground control engineers. Based on design practices of both surface and underground structures, the authors have designed and applied appropriate load factors in underground structural design projects to accommodate different rock types, entry/intersection dimensions, roof geologic conditions, availability of roof bolts and water, etc. Classification of load (reduction) factors for large-span underground intersections are presented for reference. Success of designed underground structures in effectively controlling roof stability over years indicates the applicability of the load factor concept for underground structural design, and its same significance as of the load factor specifications in ASCE/SEI 7-10, ANSI/AWC NDS (2015), and AASHTO LRFD Bridge Design Specifications (2012). The load factor concept will facilitate ground control engineers to appropriately utilize popular structural design software, such as RISA-3D or -2D to efficiently design and analyze underground structures.LOAD FACTORS IN STRUCTURE DESIGN APPLICATIONSIn structures, loads cause stresses, deformations, and displacements. Assessment of their effects is carried out by the methods of structural analysis with the help of load factors. Loads can be increased or decreased by load factors to meet the requirement that design strength be higher than maximum loads. For example, in designing a staircase, a dead load factor may be 1.2 times the weight of the structure, and a live load factor may be 1.6 times the maximum expected live load based on the Load and Resistance Factor Design (LRFD) method. These two “factored loads” are combined (added) to determine the “required strength” of the staircase. Some typical load (adjustment) factors used for structural design are as follows:"

Jan 1, 2019

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By G. A. Gamble

"The inlet air velocity profile of any surface mine ventilation fan is an important factor when designing the connecting ductwork from the mine shaft collar to the fan. Deficient fan performance can be the result of ductwork that adds unnecessary pressure loss and/or adversely influences the fan inlet air conditions (velocity profile). The need for optimized inlet air conditions begins with discussing the process of performance testing during the development of the fan performance curve. Additional discussions include design of the shaft collar connection and the connecting ductwork. A preferred design of ductwork for parallel fan installations will be illustrated.INTRODUCTIONThe inlet air velocity profile of any surface installed mine ventilation fan is one of the most important factors to consider when designing the connecting ductwork from the mine shaft collar to the fan. Oftentimes deficient fan performance can be traced to poorly designed ductwork that adds unnecessary pressure loss and/or adversely influences the fan inlet air conditions (velocity profile). Such designs may lead to added power requirement, excessive vibration and noise, and reduced fan performance.Understanding the need for optimized inlet air conditions begins with discussing the process utilized when factory testing takes place during the development of the fan performance curve.Additional discussions include design considerations for the shaft collar connection, the connecting ductwork, and fan inlet. Illustrations of cost savings and pressure losses will be included for audience consideration. The design of ductwork for parallel fan installations on the surface is another issue that requires consideration. A preferred method will be illustrated.The selection of accessory components, such as self-closing doors, can also add to the potential for reduced fan performance. Several components will be discussed.An elementary presentation of the Air Movement and Control Association (AMCA) Standard 201 “Fans and Systems” will be included to provide background for those audience members that want additional technical explanations of the need for a uniform inlet air velocity profile at the fan inlet."

Jan 1, 2019

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay, Cicek Sena, Zhao Haochen

"Analysis of Longwall Pillar Stability (ALPS) and Analysis of Retreat Mine Pillar Stability (ARMPS) treat the pillar as a passive structure that is designed to carry overburden dead-weight. This dead-weight is calculated by simple rules based on the geometry of the mining, such as “tributary area theory,” “pressure arch theory,” and “abutment angle theory.” Although the pressure arch loading approach indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology of the overburden in load calculations. The relationship between successful pillar layouts and overburden geology can be incorporated into the load calculation by using the Ground Response Curve (GRC) approach.This paper introduces the GRC modeling methodology to investigate the effect of overburden geology and excavation geometry on load transfer mechanisms using seven field measurement case studies from four U.S. mines. It was also shown that the modeling methodology used to derive GRC in this study approximates mining-induced stresses and deformations within 5% of the values measured in the field.INTRODUCTIONFrith and Reed (2017) stated that current state-of-the-art pillar design methods ignore the overburden mechanics and use estimated dead-weight of overburden to compute pillar sizes. In the United States and around the world, overburden loading is typically estimated by simple geometric rules, generally with the tributary area theory (TAT). The specific overburden mechanics, structural competence of the overburden strata, geology, in situ stresses, and overburden/pillar interactions are typically ignored. However, these important mechanical responses affect the stability of the mine pillars and openings; therefore, they also affect the safety of the mine workers.Research conducted by the National Institute for Occupational Safety and Health (NIOSH) after the Crandall Canyon mine disaster (Esterhuizen, Mark, and Murphy, 2010) showed that small panel width-to-depth ratios and stiff-strong overburden result in a reduction of the observed pillar loads, much smaller than the TAT estimate. In fact, as a response to the Crandall Canyon disaster, Mark (2010) implemented a pressure arch loading approach into the latest ARMPS program to recognize the inherently greater stability of narrow panels at depth. The pressure arch approach is a first logical step to introducing non-tributary area loading into the practical ARMPS program. Although the pressure arch loading indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology and mechanical response of overburden in the load calculations."

Jan 1, 2019

By V. Prostakova, M. Shevchenko

The copper smelting gas / slag / matte / metal / solids system with the Cu-Fe-Ca-Si-O-S major elements has been a long-term focus of the present overall research program using integrated experimental and modelling approach for the phase equilibria characterisation and development of a thermodynamic database. A systematic investigation of phase equilibria of slag systems in equilibrium with Cu metal is providing information for systems where copper coexists in slag with lead, zinc, and aluminium oxides as major components. Experimental studies involve high-temperature equilibration of synthetic samples; rapid quenching; and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). Particularly important feature of the present study a wide range of temperatures (660-1670°C) being characterised that reveals major inconsistencies in the existing thermodynamic description of the multicomponent system, and allows to establish the thermodynamic properties from phase equilibria in a reliable way. FactSage-based thermodynamic modelling is integrated with experimental research. Initial thermodynamic assessments are used to identify priorities for experiments, planned to provide specific data for thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved, in particular in the PbO-Cu2O-SiO2, ZnO-Cu2O-SiO2, and Cu2O-CaO- Al2O3 systems in equilibrium with metallic Cu. INTRODUCTION Slags high in lead and copper are generated in primary metal production in the smelting of lead sulfide concentrates and in pyrometallurgical metal recycling systems. The compositions of these slags are varied due to increased fraction of recycled materials in the feed as well as introduction of previously unused chemical elements to modern technology. Therefore, their processing becomes chemically more complex; in that way they contain a large number of different metals. These slags form complex non-ideal solutions (with possible formation of several immiscible slags) that can coexist with stoichiometric solids, solid solutions, mattes and molten metal depending on the bulk composition and process conditions. Predicting the outcomes of smelting and refining processes is becoming increasingly difficult. To assist in the optimisation of these metallurgical processing operations, a comprehensive research program is underway to develop accurate thermodynamic databases for these non-ferrous process systems.

Jan 1, 2019

By H. Henao, F. Canales

The present work evaluated the use of copper ore flotation tails as flux in the process of smelting copper concentrates. For this purpose, experimental and simulated liquidus lines were obtained at different ratios of tail/flux. Experimental variables included temperature, partial pressure of oxygen and sulfur dioxide and the conditions of tridymite or spinel saturation. The results indicate the feasibility of replacing the flux by increasing the temperature of the smelting process by 20°C. Results of simulation using FactSage and HSC confirm that the required increase in temperature can be achieved by increasing the flow of concentrate, enrichment of oxygen or increasing the matte grade. INTRODUCTION In the pyro-metallurgical process of copper production, the smelting stage produces two liquid phases, a sulphide phase rich in copper and another composed mainly of oxides called slag. The slag phase is the product of oxidation of the iron contained in the flotation concentrate. The smelting process which is carried out at temperatures of 1250°C, require the addition of silica as a flux and the injection of air enriched in oxygen (Schlesinger 2011). Currently, one of the most important aspects of the mining industry is the minimization of costs, the optimization of the use of available resources and the reduction of environmental impact. Under this context, the use of flotation tails from as a flux in the copper smelting process has the potential of reduced production costs and generate an environmental benefit by reduce the disposal amount of this waste material Regarding the use of copper tails as flux in the copper smelting process, a thermodynamic simulation study using the FactSage software had been reported in the literature (Parra et al., 2011). The results indicated an increase of 35°C in the temperature the liquidus for the equilibrium matte/spinel and a subsequent requirement of energy in the process of approximately 350 [MJ/ton slag]. Given that the calculated viscosity remains in the same order of magnitude, the melting temperature is a more relevant parameter for the evaluation of the use of tailings as flux.

Jan 1, 2019

By J. Gonzales

For this paper, blending is conceived as a linear process that takes a proportion from one stockpile or location and mixes it with another proportion from another stockpile or location, with the aim of obtaining a set of attributes in the final combination that satisfies a given quality standard. A blending class is the combination of ore attributes and grade limits that should be stockpiled in order to achieve the target quality for the process Plant. Current literature considers the number of blending classes in the Open Pit Scheduling Problem as fixed; however, this paper shows how to define specific blending classes for a given deposit so that the schedule can be solved with Sequential Linear Programming. Finally, a practical application in a Peruvian copper mine is shown, involving four ore attributes: alteration code, arsenic, oxide content and copper grade. INTRODUCTION In copper ore deposits, blending for quality has not been a typical issue as it was for coal and iron ore; however, current copper deposits in the world are becoming geologically and chemically more complex than in the past and is not uncommon to have quality standards involving up to four attributes, introducing an additional complexity to the mine scheduling process [1]. In order to solve the Open Pit Scheduling Problem with multiple ore quality constraints, two assumptions are necessary [2]: - Grade constraints are defined only by specifying an upper and lower limit; - Ore attributes in stockpiles are pre-determined, i.e., the upper and/or lower grade limits defining each stockpile are already known at the time of setting the schedule. Assuming each ore attribute is classified as high, medium or low, and there are four attributes to be controlled in the target ore quality, the number of possible blending classes would be 3^4 = 81. This number is impractical to manage in Operations, and increases the complexity at the time of running the schedule; therefore, a more efficient way of classifying ore is required. Note that in practice, one blending class can be split into more than one stockpile location due to physical capacity constraints. Therefore, the number of stockpiles could even be more than 81. BLENDING CLASSES DETERMINATION For a given set of ore grades with lower and upper limits to be achieved, one has to find all feasible ore classes such that when blended, their grades will lie within those limits.

Jan 1, 2019

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By T. Braun

In 1911, a young mining engineer named Bartlett Thane assembled a large claim block, 4 miles southeast of Juneau, Alaska. Across the Gastineau Channel on Douglas Island, the Alaska Treadwell Gold Mining Company had, by 1904, produced gold valued at more than three times the purchase price of Alaska in 1867 (Kelly, 2010). Thane knew his deposit was lower grade than other mines or prospects in the area; however, if the deposit was developed on a large-scale, the trend and size of the deposit made the project potentially economic. In 1911, Thane developed a business plan for the project and successfully attracted investor interest. In 1912, Daniel C Jackling visited the property at the request of an east coast investment group. Upon inspection of 5 years of production records for the Perseverance Mine, Jackling saw an opportunity to apply the low-grade/high volume milling technology which was widely adopted to the copper porphyry deposits of the southwestern U.S. With a design capacity of 6,000 tons per day (5,454 tonnes/day), Jackling’s innovative mill design would require high volume underground mining methods and the power of two new hydroelectric projects. By 1915, the Alaska Gastineau Mining Company was in full production. Between 1915 and 1919, the mine and mill set production records for haulage and throughput. The hydroelectric projects proved to be successful engineering marvels. Operational difficulties related to ore grade, refractory elements and labor shortages interrupted production on an increasing basis. In 1921, the mining company permanently shut down operations. INTRODUCTION The Juneau Gold Belt begins at Windham Bay near the southern end of Stephens Passage and extends approximately 100 miles north to Berners Bay (Figure 1). The first large-scale and sustained underground mine, operated by the Alaska Treadwell Gold Mining Company in the late 1880’s, established the Juneau-Douglas area as the regional hub for transportation and development. In the mid-1890’s, the combined population of Juneau and Douglas reached approximately 3,000 residents, largely driven by employment and support demands of several small to mid-size underground gold mines in the region. By 1904, the value of the cumulative gold production of the Alaska Treadwell was five times greater than the purchase price of Alaska in 1867 (Kelly, 2010). By the turn of the 20th century, economic growth in the Juneau-Douglas area relied on supplies delivered from the lower 48. Passenger and freight shipping lines required 3 to 4 days to make the one-way trip from Seattle to Juneau. Established shipping routes required experienced crews due to navigation hazards and adverse weather conditions. Even with precautions at the time, steam ships and freighter vessels experienced breakdowns or encounters with natural hazards that resulted in damage or in some cases, sinking. Interestingly, with no roads or railroads connecting Juneau to other communities in southeast Alaska, Juneau still relies on seaborn shipping in the 21st century.

Jan 1, 2019

By Ronald Ticona, Anaani Huaman, Andrea Lucero

Mine-to-mill optimization begins with a clear understanding and ongoing assessment of blasting, crushing, and grinding operations. Modification of blasting practices to optimize feed size can increase a mine’s throughput. However, this is only an initial step. To optimize the entire process and fully utilize downstream equipment, fragmentation must be measured at critical points along the size reduction circuit

Jan 1, 2019

By Michael Boyle, John Zeni

"The Blind shaft boring method is a mechanised process of excavating large diameter vertical shafts downward from the surface. It is a rotary drilling technique eliminating any requirement for personnel to enter the shaft or access underground workings during drilling and lining phases. Excavated material is delivered to surface carried by a flow of circulating fluid through the centre of drill rods. The drill assembly is suspended from a large A-frame rig and powerful winch at ground level providing vertical thrust to a hard rock cutter head. INTRODUCTION The Southern Coalfields Ventilation Shaft was constructed at a mine, 45 km north-west of Wollongong. The 5 m finished diameter (6.2 m drilled) shaft reaches a final drilled depth of 517 m, the deepest, fully lined blind bored vent shaft to date in Australia. Operated by a mining company in the Southern Coalfields, the expanding mine required a new ventilation shaft and associated surface infrastructure to service future operations. An assessment of future ventilation requirements for the coal seam operations identified a need to improve the capacity and reliability of the existing underground ventilation system in order to ensure a safe and efficient underground working environment. Installation of the new upcast ventilation shaft was determined to be the most cost effective and reliable solution to provide adequate ventilation for underground operations. The completed shaft is smooth and fully lined with steel/concrete composite liners that are hydrostatically sealed. The shaft lining is designed to meet the mine ventilation requirements for a service life of 20 years. The shaft intersects the top of the working section of the coal seam at approximately 513 m of depth. This includes the shaft collar depth and shaft bottom profiled intake section.PROJECT METHODOLOGY AND INDUSTRY BEST PRACTICE The shaft was drilled using the blind bore method, an innovative construction technique and an alternative to the traditional methods of sinking deep and large diameter shafts, such as raise boring and conventional drill and blast shaft sinking. The blind bore method allows the shaft to be drilled from the surface down without anyone having to enter the shaft or the mine during the construction process. This is by far the safest method of shaft construction and is especially suitable for difficult ground conditions where there may be unstable or water-charged strata. As this method involves drilling from the surface downward, shafts can be completed ahead of the underground mine development. Thus, allowing underground operations to focus on development and production without the conflicts of managing ventilation priority for underground contractors and mucking out spoil from excavation workings."

Jan 1, 2019

By J. Fox, K. Kocsis

"Planning for sustainable cooling potential requires protected space to successfully maintain chilled propylene glycol in storage until needed. Stored propylene glycol should be judiciously cared for, safely kept from the ill effects of heat, in order to remain useful for bulk air cooling. Minimizing the chilled temperature of the propylene glycol reservoir tanks means that atmospheric conditions will be monitored closely during the chilling phase. Storage facilities would maintain restricted airflow while minimizing possibilities for heat transfer during the storage phase. Sustainable cooling systems could reduce or eliminate the need for mechanical cooling if installed with favorable conditions. Storing the cooling potential from the winter months is what this new design is all about.INTRODUCTIONIn most subsurface, bulk air-cooling methods, the main source of potential cooling energy comes from cold-water applications. This paper investigates the practical use of harvested, chilled propylene glycol as the source of cooling potential. Propylene glycol is chosen as the cooling storage liquid refrigerant since its chemical make-up is intrinsically safe to fresh water supplies and will not harm underground workers should a leak occur in the closed cooling circuit. Harvesting the cold of winter is a meaningless endeavor without proper thermal planning for the storage of the cooling potential in cold refrigerant.PROPYLENE GLYCOL STORAGE RESERVOIRA new design for a closed refrigerant bulk air cooling system employing propylene glycol as the refrigerant is presented as the main design topic of this paper. Given that a deep and hot mine will need to be considered safe and productive, a cost-effective cooling system is desired in order for the mining operation to be considered sustainable. For underground mines at northern latitudes, cooling applied to fresh air is only required 3 to 4 months of the year. During winter, ambient atmospheric conditions can be harnessed and stored for use at a later time.The basis of this sustainable design uses very cold ambient air that is circulated around galvanized steel refrigerant reservoir tanks. The propylene glycol reservoir tanks are arranged in a concrete walled pit, or tank farm, excavated in bedrock. During the coldest months, the tank farm will be exposed to the open air. As the seasons change the tank farm will be covered with insulation to maintain the maximum cooling potential for use during the warmest months of the year."

Jan 1, 2019

By P. Rosario

"Current industry practice for HPGR assessment and sizing relies on conducting a series of tests using pilot-scale machines with roll diameters of 700 mm to 1000 mm. Substantial amounts of sample are required for such pilot test programs, typically 1 to 10 tonnes of the sample is needed depending on the level of study and complexity of the resource. Collection of large quantities of representative samples during the early stage development is challenging and expensive, thus significantly hinders the HPGR technology from being incorporated into early-stage designs. A robust and reliable laboratory test is therefore needed to allow a fair consideration of HPGR for early stage projects. With support from the Canadian Mineral Industry Research Organization (CAMIRO), the NBK Institute of Mining Engineering at the University of British Columbia (UBC) developed a suite of Piston Press bench-scale tests that correlated to pilot and full scale HPGR operating information (Davaanyam, 2015; Davaanyam et al, 2015; McClintock, 2018). The Piston Press Tests (PPTs) are capable of assessing the HPGR technology at the scoping, pre-economic analysis (PEA), and pre-feasibility (PFS) stages of project development. This paper will briefly describe the theory on which the PPTs are based, and then presents a case study conducted for a copper deposit to show how the PPTs are being used for scoping and pre-feasibility level studies. Specifically, the PPTs are being used to provide information for preliminary sizing and selection of an HPGR and to assess the effect of ore variability on HPGR performance. The results are also applied to developing HPGR circuit designs and can be incorporated in simulation so that optimum design parameters can be selected.INTRODUCTION It is widely accepted that high pressure grinding rolls (HPGRs) offer a viable energy-efficient solution for the modern comminution flowsheet design. Table 1 summarizes selected examples of HPGR applications in the hard rock mining industry. The main benefits of HPGRs are energy savings which leads to lower operating costs, and its stable operating characteristics that can better cope with variations in ore hardness when compared to the conventional SAG mill-based comminution circuits."

Jan 1, 2019

By Mark Van Dyke, Ted Klemetti, Joe Wickline

"The identification and mitigation of adverse geologic conditions are critical to the safety and productivity of underground coal mining operations. To anticipate and mitigate adverse geologic conditions, a formal method to evaluate geotechnical factors must be established. Each mine is unique and has its own separate approach for defining what an adverse geological condition consists of. The collection of geologic data is a first critical step to creating a geological database to map these hazards efficiently and effectively. Many considerations must be taken into account, such as lithology of immediate roof and floor strata, seam height, gas and oil wells, faults, depressions in the mine floor (water) and increases in floor elevation (gas), overburden, streams and horizontal stress directions, amongst many other factors.Once geologic data is collected, it can be refined and integrated into a database that can be used to develop maps showing the trend, orientation, and extent of the adverse geological conditions. This information, delivered in a timely manner, allows mining personnel to be proactive in mine planning and support implementations, ultimately reducing the impacts of these features. This paper covers geologic exploratory methods, data organization, and the value of collecting and interpreting geologic information in coal mines to enhance safety and production.The implementation of the methods described above have been proven effective in predicting and mitigating adverse geologic conditions in underground coal mining. Consistent re-evaluation of data collection methods, geologic interpretations, mapping procedures, and communication techniques ensures continuous improvement in the accuracy of predictions and mitigation of adverse geologic conditions. Providing a concise record of the work previously done to track geologic conditions at a mine will allow for the smoothest transition during employee turnover and transitions. With refinements and standardization of data collection methods, such as those described in this paper, along with improvement in technology, the evaluation of adverse geologic conditions will evolve and continue to improve the safety and productivity of underground coal mining."

Jan 1, 2019

By M. Choy, A. Kadiayi, E. Magdzinski

"Design of engineering controls to limit occupational noise exposure rely on accurate calculation inputs. Sound in mines can carry considerable distances. Mine ventilation engineers rely on noise propagation calculations to estimate silencer performance criteria for key mine fan installations that are often in proximity to occupied areas of a mine and can remain in service for decades. The blasted and rockbolted walls of hard rock mining tunnels have unique acoustical properties. Underground testing in an operating metal mine in Sudbury, Canada was performed and results processed to characterize noise propagation in mines, with the goal of improving the accuracy of noise calculations.INTRODUCTIONAs mine operators continue to improve and promote workplace safety, addressing noise at fixed infrastructure locations is observed as increasingly common. Underground fans are important to consider in this context, as they are typically loud, in proximity to occupied and sensitive workplaces, and operate nearly continuously. Predicting noise propagation from ventilation fans within underground mines has long been a challenge, with few available resources documenting acoustical properties as calculation inputs. Other factors in addition to rock face absorption properties include tunnel geometry and distance from the fan, which play critical roles in characterizing the noise level at any given point away from the fan. By understanding and establishing methods to better predict noise dissipation along underground mining tunnels, engineers can design noise controls with a greater degree of precision and confidence to effectively protect workers from over exposure to noise.This paper investigates classical methods of predicting reverberant room and direct field noise propagation. These prediction methods are then compared to noise measurements taken within the Fraser Mine of Glencore’s Sudbury Integrated Nickel Operations (Sudbury INO) Measurements were taken at a depth of ~881 m (2,889 ft), along an ~300 m (984 ft) long blasted hard rock mining tunnel. The noise along the mine tunnel resulted from the intakes of two 900 kW (1,200 hp) ventilation fans with a combined exhaust capacity of 300 m3/s (630,000 cfm)."

Jan 1, 2019

By E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Leadership is a critical component to an organization’s safety culture and influences the ways that health and safety is enacted on site. Therefore, it is not surprising that improving leadership will also improve safety. Worker perceptions of management practices are shaped through unique leader-employee interactions over time. However, few details are known about the communicative support (i.e., emotional, informational, and tangible) offered by supervisors and its impact on miners’ perceptions and performance. Using pre and post-interview data with 20 supervisors and 48 workers during six-week interventions, researchers identified positive and negative instances of supervisor support and its implications on worker performance. This paper highlights the common support tactics offered by supervisors and desired by workers to help practitioners identify ways to improve their safety culture and subsequently, the proactivity and compliance of their workforce. INTRODUCTION Supervisory leadership is a critical component to the effective implementation of an organization’s health and safety management system (HSMS). Specifically, supervisors serve as representatives of an organization and their actions are indicative of the organization’s safety culture (Eisenberger et al. 1986). Senior management has been shown to serve as a frame of reference for guiding safe behaviors in the workplace (Mearns et al. 1998) and, more recently, research has related supervisory enforcement to workers’ safety compliance (Petitta et al., 2017). Therefore, it is not surprising that by improving leadership, perceptions of management and subsequent safety outcomes are likely to improve as well (Zohar, 2002). Perceptions of management are shaped through unique leader-employee interactions over a period of time (Hofmann and Morgeson, 2004, 1999). How these unique interactions impact worker performance, however, remains unexamined. As a result, understanding how supervisor-employee relationships operate in high-risk environments is unclear (Mirza and Isha, 2017; Denis et al., 2010). A starting point to better recognize the idiosyncrasies of these relationships is by way of examining the communicative support offered by front-line management and received by industry workers. To this end, this paper uses pre- and post-interview data to study the communicative aspects of supervisor-employee interactions at mine sites. The analysis uses a social support framework to identify positive and negative instances of supportive communication. From interview data with 20 managers and 48 mineworkers, data emerged that shows how supervisors’ unique types of support contribute to workers’ perceptions, motivation, and follow-through of safe work behavior.

Jan 1, 2019

By J. Weyer

"Threshold limit values (TLVs) for NO and NO2 have been reduced drastically in 2016. Emissions of diesel engines have been reduced in the last decades. In many cases this is not enough to stay under required TLVs. Remaining gas in the blasted rock is set free during loading and transport. At the end, only a combination of measures with a further reduction of diesel motor emission, replacement of diesel driven vehicles by electric equipment, new explosives with reduced NO and NO2 production, changes in the organization and effective ventilation measures can ensure that the TLVs are not exceeded. KEYWORDS Blasting fumes, Gas measurement, Gases, Threshold Limit Value (TLV) SHORT HISTORY OF EXTRACTION OF RAW MATERIALS The extraction of raw materials—besides haulage and transport—is one of the main processes in mining and tunneling. The principal objective is the creation of a material which can be transported from the place of extraction (face) to another place for further processing or direct use. Furthermore, recently a desired grain size distribution has become more important. A revolutionary development took place in the course of centuries. With the use of primitive tools like shovels, chisel and iron in the 12th/13th century in Freiberg, ore mines performances of 12 16 cm per man and week could be reached in cross section of 1 m2. Recalculated with an assumed average density, this is a performance of 0.006 t/h. With the introduction of black powder into the subsurface in 1627 by Caspar Weindl in the city of Schemnitz (nowadays Banska Stiavniza), performances increased. A part of the hard extraction work was now done by the explosives. But first in 1767, it was recognized in a mine in Freiberg that more than 1 hole could be drilled (hand-drilling) and blasted. This discovery was so important that a plate with an inscription describes this event. The performance was increased more than 10 times compared to the extraction with chisel and iron. Since this time, drilling and blasting has been the most important innovation force for the increase of the performance. Problems with noxious blasting fumes led to the construction of the first tunneling machine by Henry Joseph Mouse in 1846 (beside shield machines from 1825) (Stack, 1982)). The triumph of mining machines started only interrupted by the two world wars. The development of hard rock boring machines (including roadheaders) was enforced after 1945. An almost complete extraction by hard rock boring machines was predicted for the turn of the millennium. And, indeed, one could find powerful machines in Canadian potash mines which were able to mine 1000 t of potash in 1 hour. That was an increase in the performance by several powers of ten. But already in the 1980s, it was recognized that the ambiguous goal could not be reached. Problems with wear of the tools, radius of curves, minimal length of openings, size and costs of the machines led to a more or less parity between drilling and blasting on one side and machines on the other side, of course depending on the field of use. For this reason, drilling and blasting is still the dominant extraction technology for raw materials. In the development of drilling and blasting technologies, the focus was mainly on the improvement of the safety but also on the increase of the blasting power and performance. Examples are tests for the increase of the power of ANFO explosives which were carried out in the 1970s and 1980s, in the former teaching mine “Reiche Zeche”. In the 1980s vehicles for loading and mixing of ANFO explosives have been developed, the blasting cab sensitivity of ANFO has been increased, emulsion explosives have been developed and up to now further developments like PMMA LOX EX explosives are on the way. At the turn of the millennium, 6 million t/a explosives have been used worldwide. Annual rates of increase of 2% have been predicted (Weyer, 1999). Meanwhile the focus changed from an increase of the performance"

Jan 1, 2019

By H. M. Lizama, R. L. Stephens

Secondary leaching of previously leached supergene copper ore has been developed and implemented at Teck’s Quebrada Blanca operations. This consists of using in-situ leaching techniques aided by geophysics to recover the residual metal value from dormant copper leaching heaps. These heaps of crushed and agglomerated ore had been leached 20 years previously but still contained significant copper values. The concept was first tested on a 3,200 m² sector, where injection wells introduced leaching solution into a production zone and electro-resistivity tomography was used to track solution movement within. Operating parameters such as well spacing and injection flow rates were determined. Copper recovery and leaching performance were evaluated based on solution and metallurgical balances. Both ferric leaching and bacterial leaching were enhanced through strategies to pull air into the heap. Positive results from the initial test prompted a larger, industrial pilot test on a 60,000 m² area and 97 injection wells. This larger test obtained a copper recovery of 30% in 457 days. Secondary recovery is now being implemented to all of the abandoned heaps at Quebrada Blanca and has become a production stream. This technology has the potential of wide application to mature copper heap leach operations, and Teck has patented the process and associated methodologies. INTRODUCTION Heap leaching of copper secondary sulphides has been carried out at Quebrada Blanca (QB) since 1994. Ore from the supergene deposit was crushed and agglomerated prior to leaching. Originally, the ore was leached in 6 m lifts stacked one on top of another, known as a static pad configuration. However, in 1998, after the second lift, the operation changed to a dynamic pad configuration; the ore was leached in a single lift and the resulting residues were removed to make way for fresh ore (Yáñez, Ahlborn, & Ramos, 2007). The first two static lifts were left in place and served as a foundation for the dynamic lifts above. Those two buried lifts of leached residues, some 16.8 million tonnes and covering an area of approximately 0.71 million m², remained buried under the dynamic pad.

Jan 1, 2019

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019