Search Documents

By Lindaura de Souza Cândido d’Ávila, Robert Nogueira de Azevedo, Itavahn Alves da Silva, Mariana Carvalho Araújo

The present study aims at the reduction of the dolomitic limestone by the addition of lime added with high MgO (magnesium oxide) content in the sintering process. To verify the feasibility of the use of additive lime as an alternative source of magnesium oxide, sintering tests were carried out at pot grate with different percentages of additive lime addition and with proportional reduction of the calcite lime dosage, evaluating the effects on the sintering process. The results showed that the additive lime is a good source of MgO for consumption in the sintering process of iron ore.

Oct 1, 2019

By Gleison Vinicius Ricardo, Luiz Cláudio von Sperling Cotta, Artur Frederico Fonseca da Cruz, Evandro José de Castro Lopes

Binders are important raw materials in the iron ore pelletizing process. The bentonite, most usual, has been used in plants of this process since the forties due to its good performance in the agglomeration of ultrafine ore, although the silicon content in bentonite impairs the total iron content of the pellet, reducing its market value. This article studies the bentonite consumption reduction and improvement of the chemical quality of pellets by the addition of an organic binder in the productive process of Vale Vargem Grande pelletizing plant. By evaluation of variables as, drop test of green pellet, green pellet, dry pellet and fired pellet compressive strength tests, tumble index, percentage fraction of lower than 5 mm and total iron content in fired pellets, it was possible to approve the technical availability of the organic binder auxiliary in Vargem Grande pelletizing process. Nonetheless the positive influence of total iron content increase due to the reduction of bentonite consumption, it could also verify no impact on the physical quality of the pellets under the same production rhythm, approving once again the use of organic binders in pelletizing process.

Oct 1, 2019

By Chengjia Shang

Aiming at greatly increasing efficiency and saving budget, higher strength and larger-diameter pipes have been developed and applied for constructing long distance pipeline projects in China. At the same time, in order to produce pipeline steel with high strength, high toughness and excellent DWTT performances, it is critical to refine austenite grain by static recrystallization rolling. Therefore, this paper focuses on the brief introduction of development of pipeline projects in China and also on the basics research in the field of static recrystallization during austenite processing of Nb-bearing steel.

Oct 1, 2019

By Renato Cortes, Claudia Lopes, Ewerton Campos, ALEXANDRE CALDELLAS BARBOSA

São diversas as razões para se utilizar a realidade virtual (RV) em treinamentos, dentre elas pode-se destacar a redução de custos, redução de riscos ao ambiente e envolvidos e também a possibilidade de reproduzir ou simular situações impossíveis, muito complexas ou ainda em outro lugar ou até mesmo em outro espaço temporal. Nesse trabalho será apresentado um estudo exploratório sobre o uso de RV, realizado uma pesquisa de mercado e apresentado o estudo de caso de como a ArcelorMittal Tubarão vem trabalhando essa tecnologia nos seus treinamentos corporativos no ano de 2019. A aceitação da tecnologia pelos empregados nos treinamentos foi acima de 98% e também foi demonstrado que além de aumentar a atratividade e a retenção do conhecimento, os ganhos foram ligados também a redução de riscos, redução de tempo de treinamento, experimentação de situações críticas, redução de custos, ou seja aumentou a eficiência e eficácia do treinamento.

Oct 1, 2019

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By Delio Amorim

Industry 4.0 concepts is the new biggest challenge on the industry nowadays and every company in every industry in every part of the globe is looking to implement this somehow on their factories and machines. To do that on the newest long rolling mills, that brings already onboard state-of-the-art technologies, is for sure a challenge of machinery builder industry, but how to become the long rolling mills built on 70’s, 80’s or 90’s part of this innovation process and connected to the new trends? This is the main mission here, to show some examples of applications that goes in this direction.

Oct 1, 2019

By Leandro Moraes da Silva Graciotti, Lorenzo Bortolon Scandian

Este artigo tem como premissa apresentar o quadro evolutivo referente a Segurança do Trabalho no Terminal de Produtos Siderúrgicos (TPS) do porto de Praia Mole bem como mostrar as novas ferramentas e tecnologias aplicadas ao processo portuário para garantir a perenidade das operações. Neste documento apresentaremos o Terminal de Produtos Siderúrgicos, sua estrutura de funcionamento, e as operações executadas. Em seguida, explicitaremos as ferramentas de gestão de segurança utilizadas e suas tecnologias. Por fim, exibir-se-á os impactos provenientes dos recursos e ações de segurança executadas, enfatizando a importância da tecnologia em conjunto com a segurança do trabalho no TPS.

Oct 1, 2019

By José Aparecido Pereira

The innovative methodology developed by the author allows the elaboration of an Angle Roll Pass Design based on the practical observations of the rolling process and applies mathematical criteria, using the Ekelund´s formula supported by Advanced Excel tools (Reach Goal, PROCV-PROCH, Macros) and AutoCad. The first step is the definition of the number of stands, roll dimensions, gear boxes reduction, initial stock, average reductions, spread factors, finishing speed and type of grooves. For each pass are calculated: bite angle, spread, section reduction, lost and gain of temperature, separating force, speed, torque and motor power. After these calculations and checking of the parameters, the program calculates the dimensions of the passes transforming the flat passes into shaped ones. With these dimensions it is possible to draw the grooves using AutoCad and check section reductions. This methodology was already used for the development of a new project and also to check the parameters of existing ones, with comparison of the results and has shown to be reliable in real and tested projects. It is an innovative process that is not available in known literature.

Oct 1, 2019

By Antônio Augusto de Morais Piau, Miguel Araujo de Vasconcelos Filho, Bruno Mynelly Galdino de Sousa

Sludges and dusts generated by steel mills usually cause environmental problems and has a high cost solution. This presentation offers a different aproach to the problem with a solution that not only solves the enviromental issue but also brings great savings to the mill. This technology, reuses dusts and sludges in the sintering process, after they are mixed to the right composition.

Oct 1, 2019

By Bruno Deves Flores, Alessandro Gums, Eduardo Osório, Matheus Teixeira Fraga, Anderson Azevedo Agra, Janaína Machado, Antônio Cezar Faria Vilela, Anderson Nicolodi

A utilização de carvão vegetal em substituição a outros materiais de origem fóssil na produção de coque é uma das alternativas para mitigar as emissões de CO2 na siderurgia. Contudo, a inserção de carvão vegetal na coqueificação apresenta fortes limitações, as quais estão principalmente associadas à sua elevada reatividade ao CO2. Assim, o presente estudo visou investigar alternativas para diminuir a reatividade do carvão vegetal. Para isso foram investigados os efeitos da temperatura de pirólise, desmineralização e impregnação por alcatrão. Os resultados mostraram que o aumento da temperatura de pirólise diminui a reatividade do carvão vegetal. Essa mesma tendência foi também observada ao se remover os componentes inorgânicos do carvão vegetal e ao se impregnar a sua estrutura com alcatrão. A associação dos tratamentos térmico, de desmineralização e impregnação com alcatrão resultou em reduções de reatividade na ordem de até 6 vezes a do material inicial.

Oct 1, 2019

By Henrique Silva Furtado, Flaviani Marculano Marchesi, Silas Gambarine Soares, Elton Volkers do Espírito Santo, Felipe Fardin Grillo, Heitor Cristo Clem de Oliveira

Devido ao aumento da restrição do teor de enxofre nos aços torna-se necessário investigar a eficiência do processo de dessulfuração de ferro gusa. Portanto, o objetivo deste trabalho é empregar diferentes matérias-primas e fundentes como cal calcítica, sodalita, pré-cal, mistura padrão, fluorita, escória de KR, borra de alumínio e B2O3, a fim de encontrar a composição com maior eficiência de dessulfuração, relacionando-a ao fator de dessulfuração, obtido pela termodinâmica computacional. Os testes foram realizados a 1350°C, em uma atmosfera inerte com agitação constante. Os resultados mostraram que a mistura com maior eficiência foi aquela com 69% de cal, 5% de sodalita, 15% de pré-cal, 6% de escória KR e 5% de B2O3.

Oct 1, 2019

By Lucas Gonçalves Generoso, Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, Gustavo Serrano dos Santos, Gustavo Alexandre da Costa Manso

O Alto-Forno 3 da Usiminas iniciou sua atual campanha em 1999. Projetada para durar 15 anos de operação, previa-se uma produção de 41 Mt de gusa. A partir de 2008, iniciaram as avarias mais significativas no sistema de refrigeração, possibilitando a entrada de água e os consequentes distúrbios operacionais. Buscando estender a atual campanha até 2021, a Usiminas realizou, dentre outras atividades de preservação, duas trocas de staves, em 2015 e 2018. Neste trabalho, são apresentados o planejamento e os principais procedimentos relacionados à parada operacional do alto-forno para a segunda troca de staves, com foco nas atividades operacionais que permitiram a redução do nível da carga até 25,1 metros em relação ao stock line. Destacam-se os cuidados e o êxito no abaixamento de carga até o nível das ventaneiras e a metodologia de troca de staves adotada. Por fim, a previsão de extensão da campanha em 7 anos, possibilitará atingir uma produção acumulada de 53,5 Mt, superando em 12,5 Mt o valor projetado.

Oct 1, 2019

By Andrea Codutti, Gianni Tiussi, Andrea Tonnicchi, Morris Codarin

Essar Algoma Steel, Canada, awarded Danieli Transimissions a strategic order for the upgrade of the main drive spindles belonging to the most loaded stands of the Hot Strip Mill, F1-F2, F5 and F6. Featuring special heavy duty design and advanced torque monitoring system, these spindles replace existing competitors’ grease lubricated design with the efficient continuous oil lubricated solution to withstand the tough working conditions, increase life expectations and provide room for a product mix extension. The first couple of spindles have been installed in September 2017 by the expert Service team and are showing already good and reliable performance. Progressively all the others are being installed.

Oct 1, 2019

By Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, José Eduardo da Silva Moreli, Beatriz Fausta Gandra, Adriano Cesar Carvalhido

No atual cenário siderúrgico, o prolongamento da campanha de um alto-forno tem sido prática usual em diversas empresas. Nesse contexto, a Usiminas tem realizado diversas ações de preservação dos altos-fornos, conciliando com a manutenção da competitividade. Particularmente, o Alto-Forno 3 da Usina de Ipatinga passou por duas trocas de staves, em 2015 e 2018, totalizando a substituição de 68 peças. No presente trabalho é apresentado o planejamento e a execução do retorno operacional após a 2ª troca de staves, destacando as contingências adotadas e lições aprendidas face às ocorrências que impactaram o cumprimento do cronograma previsto. Essa intervenção possibilitará a postergação da reforma para 2021, em alinhamento com as diretrizes da empresa e garantindo uma estabilidade operacional, fundamental para os cumprimentos e superação das metas.

Oct 1, 2019

By Božidar Šarler, Umut Hanoglu

A rolling simulation system has been developed to calculate the macroscopic rate of deformation, stress, strain, and temperature fields by using a novel meshless method. The model is based on two-dimensional traveling slice assumption. The slices are aligned towards the rolling direction. The initial size of the billet, bloom or slab and the geometry of the grooves at each rolling stand, the distances between the rolling stands, and continuous or reverse rolling can be arbitrarily considered. The purpose of this paper is to complement these development by predicting and visualizing also the grain size of steel over the strand cross-section for each position in the rolling mill. The grain size models have been in one-way coupled to the macroscopic calculations. First the critical strain for dynamic recrystallization is being checked. If the calculated strain is higher than that, considering also the time for meta-dynamic recrystallization, dynamic or meta-dynamic grain size calculations are carried out. If the strain is too low then only the static recrystallization is considered together with its required time. Finally, austenite grain size and ferrite grain size are calculated respectively as the steel cools down. The listed physical models are based on collection of empirical relations found in literature. The user of the system is free to choose or create the model he wants with his own parameters. The simulation system has been coded as a user friendly computer application for an industrial use based on C# and .NET framework and runs on regular PCs. The computational time for a rolling simulation is usually less than one hour and can thus be straightforwardly used for optimization of the rolling mill design in a reasonable time.

Oct 1, 2019

By José Fagundes Junior, Cleudson dos Santos Rego, Bruno Bastos da Silva Murad, Vitor Borlot Borba

Since the startup in 2002, the Hot Strip Mill at ArcelorMittal Tubarão has increased gradually the coil output as the customers demand new and more resistant dimensionally challenging (thinner and/or wider) steel grades. As a critical feature for customer applications, improvements have been carried out aiming a higher thickness performance and reduction of internal losses while still meeting the more restrict tolerances booked by the customers. This paper presents the recent thickness performance evolution since 2017 and the main actions deployed to improve it.

Oct 1, 2019

By Fabrício Domith Rodrigues, Marcelo Moreira Furst Gonçalves, Leonardo José Silva de Oliveira, Luiz Fernando Andrade de Castro

Eventualmente é necessário ajustar a largura de placas via processo de oxicorte. Contudo, o processo de corte convencional a frio não é recomendado para algumas qualidades de aço por gerar susceptibilidades às trincas na seção de corte. Para contornar a ocorrência de trincas no corte convencional foi desenvolvida e aplicada na Usiminas uma nova técnica de oxicorte em placas com base na utilização de duplo maçarico. Após otimização dos parâmetros de velocidade e posição dos maçaricos foi possível obter temperaturas da ordem de 200°C, homogeneamente distribuídas ao longo da seção de corte, favorecendo o ajuste dimensional sem trincas. Com a implementação industrial, verificou-se índices superiores a 85% de aprovação de placas e, consequentemente, o aproveitamento de placas que anteriormente não eram destinadas a geração de produtos laminados.

Oct 1, 2019

By Baoliang Xiao, Hui Pan, Yajun Hui, Kun Liu

The microstructure, properties, strengthening mechanism and work hardening mechanism of 600MPa grade high ductility hot-rolled sheet steel for automotive square tube were investigated by utilizing optical microscopy, scanning electron microscopy and transmission electron microscopy. The results show that the microstructures of low C-low Mn-Nb and Ti microalloyed steel (Steel A) and high C-high Mn-Nb microalloyed steel (Steel B) are composed of ferrite and a small amount of pearlite. Compared with steel B, the size of ferrite and pearlite of steel A is finer, while the size of the second phase precipitates is larger. The mechanical properties of the two tested steels are similar before tube forming, except that the yield ratio of steel A is higher. Steel A has/exhibits significant work hardening after tube forming; the yield strength and tensile strength increase by 45 MPa and 26 MPa, respectively, while the elongation decrease by 6.0 percent. The yield strength and tensile strength of steel B increase by 22 MPa and 10 MPa, respectively, and the elongation decrease by 4.0 percent. The grain refinement strengthening is the dominant strengthening mechanism, accounting for 52.9 to 61.8 percent of the total yield strength; the solid solution strengthening is the second strengthening mechanism, accounting for 17.2 to 25.3 percent, while the precipitation strengthening and dislocation strengthening contribute little to the yield strength. The dislocation strengthening increase by 82 MPa of steel A after tube forming, which is higher than that of steel B. Therefore, steel B has a low work hardening rate that is more suitable for manufacturing automotive square tube for secondary tube forming.

Oct 1, 2019

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz

Embora a resistência ao desgaste seja geralmente a principal propriedade avaliada decorrente da adição de terceiros elementos em ligas Al-Sn, não somente os fenômenos tribológicos são responsáveis pela deterioração gradual das peças, mas também os fenômenos relacionados à corrosão. Dessa forma, o presente estudo objetiva analisar o efeito de características microestruturais formadas durante a solidificação transiente da liga Al-9%Sn-5%Zn na resistência à corrosão em solução 0,06M NaCl investigada por polarização potenciodinâmica e espectroscopia de impedância eletroquímica. Foi observada uma morfologia microestrutural caracterizada por dendritas da fase α-Al com concentrações de Zn tanto na matriz dendrítica quanto em regiões ricas em Sn localizadas nos contornos interdendríticos. A evolução dos espaçamentos dendríticos primários (λ1) também foi correlacionada com parâmetros térmicos de solidificação. Finalmente, constatou-se que a amostra com microestrutura mais grosseira, ou seja, λ1 = 89,6 μm, apresentou comparativamente menor densidade de corrente de corrosão e maior resistência à polarização.

Oct 1, 2019

By Marcus Weldon

We are at the beginning of an era of profound transformation and human progress — a new industrial revolution. This “Automation of Everything” era will be brought about by digital interfaces, data analysis and control of the physical world through networks employing the Nokia Bell Labs Future X1 architecture — networks to support the digitization and connection of everything and everyone with the goal of automating much of life. The interconnection of robots, machines, drones, sensors, processing platforms and people through Future X networks will provide transformative tools for the automation and optimization of factories and warehouses, ports, electric grids, transportation networks, food, healthcare, construction, logistics and supply chain, emergency response, mining, and other physical industries. To date, the level of automation has been modest at best. Automating these physical industries — industries that account for 70 percent of the US Gross Domestic Product, for example — has the potential to drive significant increases in the world’s economic productivity.2 Realizing the potential of this next industrial revolution will require billions of wirelessly connected endpoints for high fidelity physical-to-digital conversion, millisecond response times to tightly control and coordinate machines and robots, and intelligent analysis to optimize real-time decisions — tasks beyond the reach of current networks. Increased levels of automation are already being achieved through the use of 4G advanced wireless access technologies. The untethering of sensors and actuators in industrial environments through the low-latency, high-bandwidth, high-reliability, and massive scale provided by 5G wireless access will complete this evolution, providing an unprecedented ability to digitize, analyze, comprehend and manipulate the physical world at a scale never previously thought possible. These new capabilities will enable us to create digital models of the physical world with ever higher levels of fidelity, further enhancing our ability to improve operational efficiencies and increase productivity and worker safety. Doing this will require a dramatic evolution in network architecture toward massively distributed cloud control and baseband capacity to achieve the required ultra-low latency and ultra-high bandwidth for industrial and infrastructure automation services — the Future X architecture. In early 2019, Nokia Bell Labs will publish a sequel to “The Future X Network: A Bell Labs Perspective”. “Future X for Industries: A Nokia Bell Labs Perspective” will explore how the Future X architecture will automate many of the world’s physical industries, including chapters devoted to electric power, cities, rail, mining, public safety, manufacturing, ports, logistics and supply chain, and an overarching chapter devoted to securing this highly automated world. To give you a small taste of the feast that’s to come, we’re sharing with you an initial installment — “Future X for Industries: Mining” — the Nokia Bell Labs view of how mining will be transformed through a Future X architecture..

Oct 1, 2019