Search Documents

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

By Michael P. Sudbury

Non-ferrous slags are granulated and stockpiled as an alternative to pit cooling or transporting molten slag to a dump. The chemical composition of such slag is determined by the pyrometallurgical process in which it is produced, while the size distribution is set by safety concerns or a desire to reduce wear of pumps, pipelines and other equipment. Relatively few operations give consideration to the effect of granulation conditions on other properties of the granulate as the material is typically accumulated on the smelter site. It is becoming recognized that slag has many potential commercial uses and carries much of the energy applied to the smelting operation. This paper outlines the findings of extensive work to identify uses for granulated non-ferrous slag, the importance of preparation conditions on the properties, impediments to more extensive use of granulated slag, the real costs of slag stockpiling and the opportunities for further productive research.

Jan 1, 2006

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005

By Liang Sha

In this study, adsorption of copper by chemically modified orange peel was investigated. A conspicuous change occurs in the surface morphology of the biomass due to modification, which is depicted by SEM images. Equilibrium isotherms and kinetics were obtained and the effects of various factors, including solution pH, contact time, initial metal ions concentration and temperature, were studied by batch experiments. Kinetics was found to be best-fit pseudosecond- order equations. Equilibrium was better described by Langermuir isotherms rather than Freudlich isotherms. At 25?, pH5.30, the maximum adsorption capacity was 70.67mg?g-1 . With increase of temperature, adsorption efficiency decreased. The biosorbent was suitable for repeated use for more than five cycles.

Jan 1, 2009

By C. E. M. Meskers

Electronic and Electric Equipment contains a range of components made of a wide variation of metals, plastics and other substances. Up to 60 elements can be found in complex electronic equipment: base metals, precious metals and special metals in circuit boards and batteries. Because of its amount WEEE represents a considerable metal resource with a higher special and precious metal content than found in ores. The Umicore integrated smelter and refinery recovers and supplies back to the market 17 different metals from EEE. Pre-treated materials enter state of the art, material and energy efficient metallurgical processes for environmentally sound recovery of metals and treatment of off gasses and hazardous substances. The organics in the feed function as reducing agent and alternative energy source during smelting for precious metal recovery. Lithium-ion batteries are treated using a dedicated process. As a result the environmental footprint of metals produced from EEE is much smaller than primary production.

Jan 1, 2009

By J. W. Bridge

Triaxial compression tests at various confining pressures and temperatures, as well as tangent modulus tests using ultrasonic waves, were conducted for wax-coated granular composite materials. The material used is a surface for Thoroughbred horse racing. The purpose of these tests is to examine how track shear strength and tangent modulus at a range of loads respond to changing temperatures. Previous work has shown that a wide range of operational temperatures are experienced which have been reproduced in the lab. Using differential scanning calorimetry, it is confirmed that these operational temperatures correspond to distinct thermal transition regions for the wax that is used to coat the sand in these surfaces. Preliminary results show that both shear strength and tangent modulus are sensitive to temperature changes with maximum strength and modulus correlating with major DSC wax transition regions.

Jan 1, 2010

By J. R. Goode

Up to one half of neodymium and praseodymium production, key ingredients in permanent magnets, is produced illegally. About 60% of cobalt production, critical in lithium-ion batteries and other applications, comes from central African states, and much of it is produced illegally. Tantalum, important in modern electronics, is also primarily sourced from central Africa and, again, much of it illegally. Illegal mineral production, as exemplified here, is often used to fund armed conflict. Furthermore, it is typically conducted with scant regard for human rights and environmental protection. It also leads to depressed prices which in turn limits the possibility of legitimate producers entering the market. Systems of traceability and provenance, along with cooperative supply chain participants can limit the production of illegitimate material and thereby improve conditions in the countries of origin and reduce downward pressure on prices.

By Youliang He

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By A. E. M. Warner

In co Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

The effect of rare earth element Y (0-2.0at.%) on the microstructure of TiAl alloys at the as cast and rapidly solidified conditions has been investigated. The results show that the addition of Y greatly refined the microstructure of TiAl alloys at both conditions. The refinement is more significantly with higher Y content. The refinement of Y in the cast alloys is attributed to that the strip-shaped Y-rich phase locating on the grain boundaries impedes the grain growth during solidification. In the rapidly solidified alloys, Y-rich phase dispersing uniformly as spherical particles in the matrix acts as heterogeneous nucleation sites which increases the nucleation rate of ??phase during the ????phase transformation, and produces a refined initial microstructure during solidification. Higher cooling rate restricts the grain growth during subsequent cooling.

Jan 1, 2010

By P. Ret, E. Üstiindag, R. Dieckmann, R. Subramanian, S. L. Sass

"Partial reduction reactions in the Ni-AI-O system, starting with the spinel compound NiAI20 4, are used to form metal-ceramic microstructures. By suitable choice of processing parameters, such as reduction temperature, oxygen partial pressure and time, two different morphologies of nearly pure Ni particles, equiaxed and rod-like, form within a ceramic matrix, which is either a-A12O3 or a metastable ""defect spinel"". Electron microscopy studies were performed for microstructural characterization, phase identification and chemical analysis. The fracture toughness of the Ni-AI2O 3 mixture was significantly improved with respect to that of the original spinel phase. The important issues that must be addressed to form useful metal-ceramic microstructures by partial reduction reactions rue discussed. It is shown that cracking at the original spinel grain boundaries, likely due to the large volume changes associated with the reduction reaction, can be avoided by the addition of small amounts of ZrO2• Initial results illustrating effect of ZrO2 on the microsuuctures are presented.IntroductionEngineering materials used in load bearing circumstances, particularly under extreme conditions (e.g. high temperatures or stresses), generally are formulated with complex microsuuctures. Such composite-like materials can possess properties unobtainable by either of the individual constituents. With metal-ceramic composites, for example, a material can be obtained with an optimum combination of the low density and high strength of the ceramic, and the toughness of the metal. For high temperature service, where demanding conditions are often present, for example, inside jet turbine engines, a successful new material must have low density, high Young's modulus as well as good oxidation resistance, strength, fracture toughness, creep and fatigue resistance. The candidates include intermetallic compounds, and metal-ceramic, intermetallic-ceramic and ceramic-ceramic composites."

Jan 1, 1994

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades. EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized.

Jan 1, 2003

By M. Hochenhofer

Keywords: desulfurization, mathematical model, slag reaction To produce ferroalloys like ferro-nickel for alloying purposes in a quality that meets the requirements of today?s steel industry, refining processes like desulfurization and dephosphorization are indispensable. The performance of desulfurization-treatment by slag reaction depends on various parameters, such as: sulfide capacity and viscosity of the slag, sulfur distribution between metal and slag, activity of sulfur in melt and movement of melt. Within this work, the combined influences of these parameters on the desulfurization of a ferro-nickel alloy were examined. As a basis for this examination, a mathematical model, based on data from plant trials, was created. This model demonstrates the relationship between desulfurization rate and initial values of the above mentioned parameters. With this model the relevant parameters were evaluated and assessed concerning their influence on desulfurization.

Jan 1, 2005

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By M. I. Zinigrad

A model of an ideal associated solution is presented. This model takes into account the existence of complexes of various compositions, sizes and geometries and allows calculating thermodynamic properties and phase diagrams of binary alloys. The model has been used formerly to calculate thermodynamic parameters and the position of the liquidus line for binary eutectic systems and also those having a stable compound in the solid phase. In all the cases the model parameters were not adjusted rather estimated from melting temperatures of the components. The recent studies dealt with the influence of arbitrary-stoichiometry associates on the equilibrium thermodynamic properties of liquid alloys. The application of the model to eutectic systems and systems having an unlimited solubility in solid and liquid states close to liquidus has been considered. It was shown that if the difference in melting temperatures of the components was small, different types of fusibility diagrams were possible: eutectic diagrams, cigar-shaped diagrams or diagrams with upper or lower azeotropic points. Peritectic transformations could take place when the difference in melting temperatures of the components was large. The present work is devoted to calculation of phase diagrams and thermodynamic properties of binary systems on the basis of chrome.

Jan 1, 2006

By Qingwei Wang

Heavy metal-containing wastewater from hydrometallurgical processes of lead-zinc was treated by biologics in a 200 m3/h industrial scale experiment. The result shows that Zn concentration declined from 50.28 mg/L~240.81 mg/L to 0.21 mg/L~1.98 mg/L, Pb from 1.00 mg/L~13.47 mg/L to 0.083 mg/L~0.71 mg/L, Cu from 0.24 mg/L~2.38 mg/L to 0.059 mg/L~0.40 mg/L, Cd from 2.12 mg/L~23.47 mg/L to 0.011 mg/L~0.071 mg/L and As from 0.50 mg/L~6.00 mg/L to 0.005 mg/L~0.10 mg/L. The concentrations of the above heavy metals in the treated water were lower than that in Integrated Wastewater Discharge Standard (GB8978~1996) in China. Furthermore, the treated wastewater was recycled and reused in smelter plant. Zinc content in hydrolytic sludge reached up to 34.04%, which indicates that this sludge can be used to recover valuable metals.

Jan 1, 2010

By Shadia J. Ikhmayies

The SnO2/CdS/CdTe thin film solar cells were fabricated on glass substrates by using the spray pyrolysis (SP) technique for the deposition of the SnO2 and CdS layers and vacuum evaporation for the CdTe layer. The transmittance curves were used to investigate the interdiffusion in the two interfacial regions SnO2/CdS and CdS/CdTe by taking the first derivative of the absorbance as a function of wavelength. The appearance of new bandgaps around the bandgaps of SnO2:F, CdS:In and CdTe layers is a strong evidence on the interdiffusion in the two interfacial regions and/or the formation of quantum dots.

Jan 1, 2010

By Kenneth McGowan

"The aluminum industry is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating accounts for 25% of the energy consumed to manufacture aluminum. Consequently, the generation of this energy results in the production of a significant amount of CO2 (over 3.75 million metric tons in 2003)1. As a result, the Aluminum Industry Technology Roadmap of 2003 listed the development of improved refractory materials as a goal to reduce energy use and decrease greenhouse gas creation. The result of a R&D effort addressing this desire is the development of patented microporous refractory materials for metal contact applications in all furnace areas including the belly band. It has been demonstrated that this material can reduce energy consumption up to 38% in furnaces and significantly reduce heat loss in launder and trough systems. Furthermore the material developed is non-wetting and remains un-penetrated by metal throughout its lifetime. The material does not contribute to the formation of corundum. As a result, the energy efficiency of an older lining remains intact compared to standard refractory materials which may have an initial high insulating value (such as lightweights and board) or standard dense refractory (even with penetration inhibitors) both of which show a rapid increase in thermal conductivity as the refractory is penetrated with aluminum and formed corundumIntroductionThe aluminum industry is the second largest producer of metal in the United States, behind the iron and steel industry. It is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating is required to melt, hold, purify, alloy, and heat treat the metal and accounts for 25% of the energy consumed to manufacture aluminum. As such, process heating is the second largest energy consuming operation. Smelting, which utilizes an electrolytic reduction process is the largest energy consuming operation1.Most process heating is accomplished through the use of fossil fuels, either directly or indirectly. The choice of fuel is dependent on a plant’s location and fossil fuel availability. Table I shows the processes impacted by refractories and the calculated BTU’s generated by usage of the respective fuels as well as the Metric Tons (MT) of metal passed through each process in 20001."

Jan 1, 2009

By S. Eck

In previous work the influence of the casting speed on the flow field and the shape of the solidification front in an industrial 0.82 x 0.25 x 0.8 m³ bronze caster had been investigated. Both numerical and experimental model represented 1:1 the real caster geometry. A comparison of the results of both numerical and experimental models for the flow during the casting process showed a good agreement in the qualitative velocity fields (flow direction and vortex formation). This work represents a parameter study of the numerical model with variations of the turbulence conditions at the inlet in order to clarify their influence on the flow field in the caster. In order to find the best boundary condition at the inlet, the numerical calculations for water have been compared with the measured flow fields in the water model. The new boundary conditions were then applied to the numerical model of the bronze casting process.

Jan 1, 2009