Search Documents

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011

By H. Copur

Roadheaders have become widely used in underground mining and tunneling operations because they offer the flexibility to excavate soft- to medium-strength rock formations. A critical issue in successful roadheader application is the ability to develop accurate and reliable estimates of machine production capacity and the associated bit costs. Increased pressure to improve productivity and lower costs in the mining and civil construction industries has been the driving force behind the more wide- spread use of mechanical excavation systems. This has caused both industries to move away from the conventional drill and blast methods. Additional benefits of mechanical mining include improved safety, reduced ground support requirements and fewer personnel. These advantages, coupled with recent enhancements in machine performance and reliability, have resulted in mechanical miners taking a larger share of the rock excavation market. Roadheaders are the most widely used underground partial-face excavation machines for soft- to medium- strength rocks, particularly for sedimentary rocks. They are used for development and production in soft rock mining (main haulage drifts, roadways and crosscuts), particularly in coal, industrial minerals and evaporitic rocks. In civil construction, roadheaders are used to excavate railways, roadways, and sewer and diversion tunnels in soft ground conditions. They are also used to enlarge and rehabilitate underground structures. Their ability to excavate almost any profile opening also makes them attractive to those mining and civil construction projects where various opening sizes and profiles are needed. In addition to their high mobility and versatility roadheaders are generally low capital cost systems com- pared with most other mechanical excavators. Because of higher cutting-power density due to a smaller cutting drum, roadheaders can excavate rocks harder and more abrasive than continuous miners and borers.

Jan 1, 1998

By Michael L. Ogilvie

The proportion of underground coal production as a percentage of overall Australian production has fallen in the last 10 years, with underground production remaining more or less static at about 53 Mt (58 million st). However, underground coal mining remains a viable industry in Australia, due to use of modern longwall mining systems. In 1993-1994, 26 longwalls were in operation, with total production exceeding 39 Mt/a (43 million stpy). Some of these longwalls achieve productivity levels approaching efficient opencut operations, and in some cases, they exceed them. These high-production longwall mines are not without problems when depth and distances from outcrop increase and the gas content of the seams approaches or exceeds critical limits. When gas content of a coal seam exceeds 6 m3/t (233 cu ft/st), gas flows into the mine may be sufficient to interrupt production from time to time.

Jan 1, 1995

By R. P. Killmeyer, W. W. Wen, B. K. Parekh

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen-bowl centrifuge for the dewatering and reconstitution of column -flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine clean-coal slurry from the column flotation con¬centrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free flowing granularform, while the untreated products were wet, sticky and difficult to handle. Test results indicated that the average moisture contents of the dewatered coal products were 35.7%, 35.5%, 32.6%, 29.9% and 26.5% (by weight) with Orimulsion additions of 0.0%, 0.7%, 3.2%, 4.8% and 6.4% (by weight), respectively. The handleability and dust reduction of the dewatered coal products were also vastly improved.

Jan 1, 2000

By Richard L. Stotlar

Introduction During the last decade, the metallic minerals segment of the industry could be categorized as a "feast-or-famine" business. It is no secret that metallic minerals are cyclical. Employment opportunities greatly depend on the supply and demand for its mineral products. It is also not unusual for there to be a lag between the industry's manpower requirements and academia's ability to produce new graduates. Due to this lag, there will be years with manpower shortages, as in the mid-1970s. At other times, supply will exceed demand. The question is where will the jobs be in the years to come? This presentation will review reasons why employment opportunities have declined within the metallic minerals industry. It will also predict future demand for mineral engineering graduates. And it will outline strategies for obtaining an employment offer. Historical Review - Employment From 1977 through 1983, about 75% of all metal mining employees were directly engaged in production activities, down from 83% in 1965. This decline reflects increased use of labor saving equipment, and more government regulation and foreign competition. Metal mining's employment decreased from 74,000 jobs in 1982 to fewer than 68,000 in 1983 - an 8% decline. The overall industry is having these problems because of the general downturn in the economy. For example, at the beginning of this decade, US automobile and steel industries were in trouble. Interest rates were too high and volatile. This adversely affected construction, housing starts, and manufacturing. All these industries, being large users of base metals, drastically affected the metals industry. US copper companies are still having problems. Reports indicate that many copper employers have cut production, laid-off workers, and permanently closed mines, refineries, and smelters. A decline in the demand for US produced metal products, such as copper, obviously affects some mineral engineering employment opportunities. Other factors to consider when looking at employment opportunities and why it has become difficult for US metal producers to compete in the world market include: • The grades of ore bodies of many US minerals are considerably lower than the grades of ores being mined elsewhere in the world. • The grades of ore bodies currently being mined in the US are steadily declining. • Foreign producers are largely government controlled and are not necessarily subject to the realities of supply and demand. • US environmental regulations have considerably added to production costs. Foreign producers in most countries do not have to worry about these additional costs. • US mines are getting deeper. This adds to the cost of production because of the increasing distance the ore has to be transported. • Plants and equipment are outdated. Many companies find themselves operating with equipment and plants that need modernizing or replacing. This obviously hinders competitive productivity. • Labor and management have had problems. Work stoppages in certain mining businesses and high wage and benefit costs in relation to foreign producers place US producers at a disadvantage. • Much land is unavailable. The US government owns most of the land considered to have the best potential for minerals development. Most of this land is unavailable for mining or exploration. Therefore, it appears that finding employment with a company whose primary business is mining and processing most metals, such as copper, in the US will be quite restricted and competitive. Future Demand It is difficult to anticipate what key employment opportunities within the next few years will be available to mineral engineering graduates. The Engineering Manpower Commission estimated that US engineering schools awarded 72,471 undergraduate degrees in 1983 vs. 66,990 in 1982. This was the eighth consecutive year in which the number of baccalaureates awarded has increased. On a brighter note, the US government's Occupational Outlook Quarterly stated that the growth rate through 1995 for all engineers is an encouraging 49% over present levels. The estimated number of engineers employed in 1982 is 1.2 million. The numerical in-

Jan 2, 1985

By C. A. Rowland

The use of the Bond Work Index to size industrial grinding equipment is well known. Its use to measure grinding efficiency was presented by C.A. Rowland, Jr. at an AIME meeting in 1976. However, due to a bureaucratic error, the paper was never submitted for publication. This metric has nevertheless been adopted by industry as a widely used standard. The purpose of this paper is to re-present and update the application of this tool as a standard for measuring grinding circuit efficiency. Definition ?standard, n. something established for use as a rule or basis of comparison in measuring or judging capacity, content, extent, value, quality, etc.; as standards of weight and measure? (Webster, 1958).

Jan 1, 2008

By George M. Leonard

Mineral commodities on National Forest System lands contribute to the nation's well being. Access to these commodities is dependent on public perceptions of the effects of mineral operations on other resources. An outlook is described which the Forest Service believes is essential to the minerals industry if it plans to continue seeking minerals on National Forest and Grasslands.

Jan 1, 1991

By W. Z. Choi

A combined size reduction- liberation model of grinding has been developed to predict the product size distribution for both free and locked particles. The model is an extension of the population balance model for size reduction. Locked (or composite) particles have been subdivided into discrete classes of different compositions to obtain more detailed information. The model has been tested on a sphalerite ore from Tennessee. Liberation data have been obtained using an areal scanning technique on microscope images of polished particle mounts.

Jan 1, 1985

By D. Gignac, P. A. Studemeister, H. Koza

Two epiclastic horizons in an Archean volcanic sequence host the gold occurrences on the Dunraine property near Wawa, Ontario, Canada. The Grace horizon of cherty and pelitic tuff strikes north-northwest and dips east. Native gold occurs with arsenopyrite in bedlike and podlike bodies of quartz lenses and stringers set in a pelitic matrix. The Parkhill horizon of lithic graywacke with associated flow-breccia strikes southwest and dips south. Native gold occurs with minor sulfides in similar bodies of quartz erratic within the Parkhill horizon. The auriferous bodies occupy paleotopographic channels and troughs within the two horizons. The former producers are the Parkhill mine with 1689 kg (54,300 oz) Au, Darwin mine with 473 kg (15,200 oz) Au, and Van Sickle mine with 48 kg (1536 oz) Au between 1902 and 1944. The gold occurrences are syndepositional with the host volcanic sediments laid during a pause in explosive volcanism. Fumaroles along steep gullies on the flank of a subaqueous volcanic center precipitated aprons of auriferous silica-sulfide mud. Downslope slumping resulted in exhalative debris flows; gold concentrated in flexures and depressions along stumpage channels. Renewed explosive volcanism covered the auriferous sediments with pyroclastic tuffs, arresting the slumping of in situ fumarolic deposits.

Jan 9, 1985

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

Samples collected during the exploration phase of mining represent baseline conditions at the site. As such, they can be very important in forecasting potential environmental impacts should mining proceed, and can become measurements against which future changes are compared. Constituents in stream water draining mined and mineralized areas tend to be geochemically, spatially, and temporally variable, which presents challenges in collecting both exploration and baseline water-quality samples. Because short-term (daily) variations can complicate long-term trends, it is important to consider recent findings concerning geochemical variability of stream-water constituents at short-term timescales in designing sampling plans. Also, adequate water-quality information is key to forecasting potential ecological impacts from mining. Therefore, it is useful to collect baseline water samples adequate for geochemical and toxicological modeling. This requires complete chemical analyses of dissolved constituents that include major and minor chemical elements as well as physicochemical properties (including pH, specific conductance, dissolved oxygen) and dissolved organic carbon. Applying chemical-equilibrium and appropriate toxicological models to water-quality information leads to an understanding of the speciation, transport, sequestration, bioavailability, and aquatic toxicity of potential contaminants. Insights gained from geochemical and toxicological modeling of water-quality data can be used to design appropriate mitigation and for economic planning for future mining activities.

Jan 1, 2011

By D. Stone, R. Pakalnis, B. Seymour

Most mines using backfill routinely carry out quality control (QC) testing of backfill mixes with unconfined compression test cylinders. This is true for paste operations, hydraulic fill operations, and cemented rockfill operations worldwide. However, a large number of mines simply do not prepare and test the backfill samples in a consistent manner and fail to properly analyze or interpret the test results. Conventional concrete test criteria are not applicable given the differences in the mix constituents and the fact that a large number of the backfill QC test cylinders typically fail to achieve the target strength. Standard industry practices are needed to improve the analysis and interpretation of QC test results and to provide a better means of determining if the backfill is achieving its intended target strength. This paper will attempt to lay the groundwork for standard industry practices and will address several key questions raised by operators, such as how laboratory test data compares to in-stope performance, and how many QC tests should fail before a red flag should be raised. INTRODUCTION Although paste backfill is widely used throughout the mining industry, cemented rockfill (CRF) remains as the backfill of choice in places like Nevada where very poor ground conditions mandate the use of underhand mining. The safety and stability of undercut entries beneath backfill is a function of the quality of the cemented fill, which is typically assured through routine quality control testing. In the absence of a backfill quality standard, most mines rely on concrete standards to design and interpret their backfill quality control programs. In the USA, these standards are developed and published by organizations such as the American Society of Testing and Materials (ASTM) and the American Concrete Institute (ACI). However, the application of these standards to cemented backfills can be very difficult owing to the high degree of variability in backfill mixes and the resulting variability in test results. To illustrate, the concrete industry standards denote that an acceptable (passing) test result occurs when the average strength of the duplicate test cylinders exceeds the target strength and no single test result deviates from the target strength by more than 10% (ACI 214R). Remedial measures must be taken if three consecutive tests fail. With mine backfills, it is safe to say that these criteria are rarely achievable. A further, more dramatic example is the accepted coefficient of variation for concrete QC cylinders. According to ACI 214R, the coefficient of variation (CV) should range from below 3% (excellent rating) to above 6% (poor rating). However, if this analysis method is applied to several backfill QC databases from operating mines, coefficients of variation are calculated on the order of 50%. Clearly, there is a need to develop better industry practices for assessing the quality of mine backfill and to assist mine operators with the interpretation of test results and the development of action plans in the event of undesired outcomes.

Jan 1, 2019

The last decade has seen the use of powerful computerized Mine-Wide Monitoring (MWM) systems for detecting hazardous conditions in underground coal mines. Recently, the U.S. Bureau of Mines and Jim Walter Resources, Inc. (JWR) expanded the scope of MWM system to include ground control. Single-point extensometers were installed in each of 30 intersections along a tailgate entry. These instruments monitored the rate of roof sag, a sensitive indicator of roof instability. Data were collected by the mine's own computerized MWM system. The paper describes the successful integration of ground control instruments into MWM, the data reduction procedures, and the identification of several hazardous areas.

Jan 1, 1994

By D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore, and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement, and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risk, the effectiveness of caps and covers, and provide information to aid in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs), and lysimeters. Many of the monitoring devices can be linked to a datalogger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1997

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population.

Jan 1, 1984

By S. S. Peng

A well designed mining plan is one which minimizes the cost and the mining induced problems and maximizes the recovery of the coal reserve. In order to minimize the negative effects on surface structures caused by ground subsidence process due to underground mining activities, two kinds of practices are commonly employed by the mine operators. One is the support techniques which leaves an area of coal un-mined or partially mined beneath the structure to be supported. The other is the protection techniques which protect the structure when it is subsiding with ground taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting techniques, the only currently available method in the U.S. is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However; The size of the support area designed by this method will be excessively large resulting in wasteful use of coal reserve when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for de-signing the support area. This method is based on a large amount of subsidence data collected throughout a number of major U.S. coal fields and the authors' experience with monitoring and protecting surface structures undermined by longwall panels. It considers the critical deformation in-dices that a structure can tolerate, and depth and height of underground extraction. The support area designed by this new method will not only assure the safety of the structure to be supported but also maximize the extraction of the coal reserve.

Jan 1, 1993

By I. A. Tinto

Labrador City is located in the southwestern portion of Newfoundland-Labrador, approximately 965 kilometers north-east of Montreal. The mine and beneficiation complex of the Iron Ore Company of Canada, known as the Carol Project, is situated 535 metres above sea level in a climatic region characterized by cold winters and short, cool summers. History The iron Ore Company of Canada commenced work in the area in 1949, however, it was not until 1958 that the decision was made to proceed with mining operations. The ore body consists of Specular Hematite (Fe203) and Magnetite (Fe304) with small quantities of Limonite and Geothite. The average grade of the ore bodies is 39% iron.

Jan 1, 1985

Contents

Jan 1, 1985