Search Documents

By S. A. Shuey, P. Taylor

The recycling of electronic waste (e-waste) tends to be a rather complex undertaking when considering the intimate bonding of materials in the average printed circuit board. The development of a recycling process is further complicated when considering the wide variety of products being generated under the heading of “electronics” as well as the constant change in materials of construction coupled with the speed at which electronics are changing. CSM researchers have undertaken a survey of the current state of pyrometallurgical processing of e-waste. This base-line will set the stage for the development of new recycling technology at CSM.

Jan 1, 2004

By C. Strachan

This paper presents an evaluation of tailings dam incidents from the 1994 USCOLD Tailings Dam Committee report. Comparisons are also made with water storage dam incidents from USCOLD reports and recent tailings dam incidents. The evaluation results show that tailings dam incidents are due to a number of factors including overtopping, static and seismic instability, seepage and internal erosion, and foundation conditions, and that no particular type of tailings dam or operational condition is more susceptible to incidents. In addition, the results confirm that tailings dams should be located, designed, operated, and reclaimed with a thorough knowledge of site conditions, mill operation, site monitoring, and tailings characteristics.

Jan 1, 1999

By P. Harris, G. Groenmeyer, L. Parolis

The effect of molecular weight, charge and the presence of the cations Ca2+, Mg2+and K+ on the adsorption of carboxymethyl cellulose on pure talc obtained from Balmat, New York have been investigated. Higher adsorption densities were obtained in the presence ofCa2+ and Mg2+ ions than with K+ ions and higher ionic strength solutions resulted in higher adsorption densities. Changing the molecular weight did not influence the adsorption however increasing the charge (DS) of the polymers resulted in lower adsorption densities.

Jan 1, 2004

By Y. P. Chugh

During late 2010, a scientifically founded water spray system was developed for continuous miners (CM) (Patent Pending) that reduces respirable dust exposure for miner operator by about 30%. It includes engineered sprays around the cutting drum, outer bit-ring sprays, chassis sprays and side cutter boom sprays. About 3.6 ? 4.5m (12-15 ft) behind these sprays is additional sprays that spatially cover the area between the CM chassis and the mine roof and ribs. The spray system uses approximately the same volume of water as currently used on CMs with similar operating pressures. An Illinois mine decided to implement these concepts on a CM during rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric sampling and real-time monitoring using multiple personal dust monitors (PDMs). The average results based on about 105 cuts show about 30% and 20% reduction in dust exposure for the miner operator, and the haulage unit operator. Visibility in the mining areas was also significantly improved. The coal company has already decided to implement the system on all their CMs.

Jan 1, 2012

By T. M. Biddle

If an accident occurs at a mine, the mining company, its parent and affiliates, and its supervisory employees may face substantial -- and sometimes unexpected -- liabilities and costs. This presentation surveys the likely sources for post-accident exposure, including wrongful death and personal injury claims, mine closure/operational disruptions, and government civil and criminal actions against the company and its employees.

Jan 1, 1986

By C. G. Tester

Automatic tripper control systems can be reliable and as such are suitable for use in the mining industry. Proper application of fundamental engineering principles provides the means for the reliability. Some of the principles are: (1) Be sure the system designer designs a system that does the job operations people want done; (2) Use sound logic design practices to avoid internal electrical problems; (3) The design must be maintenance oriented; and (4) Use good quality components. I would like to discuss a tripper control installation at Kennecott Copper Corporation, Chino Mines Division, in Hurley, New Mexico, and how these principles apply to this tripper control system. First, however, I will expand on the principles to clarify just what is meant. First, "Be sure the system designer designs a system that does the job operations people want done.? Operator acceptance is often the key to the success or failure of an automatic control system. One of the best ways I know of to get operator acceptance is to give him a system that he wants. I don't mean to imply that if bad practices or procedures exist that they should be incorporated in the control system. I do think that many designers feel they haven't done their job if the control system doesn't do things drastically different than the old manual method. Good engineering principles dictate that the job should be done right and if the manual method was right it can very likely be right for the automatic method.

Jan 1, 1973

By Jeff Easton, J Johnson, D. Foot

The Mina Santa Rosa mine in Panama was the victim of a mine closure 24 years ago that left the community in dire straits. The mine showed the potential resources of greater than 1M ounces of gold and 4.5M ounces of silver. Veragold Mining Company decided to reopen the mine and address all the issues that were involved in the startup of an historic mine. This paper provides methods to restore the community trust, provide a transparent process, and develop an environmentally sound flowsheet. Immense scrutiny surrounded the Tailings Storage Facility, and the company developed a plan focused on paste thickening and surface stacking to eliminate the need for a conventional tailings’ facility. Paste thickener principles and benefits are also provided.

Feb 1, 2024

By Pooyan Asadollahi, Praveen Krishna, Michael Joye

"Durability design for underground structures is an increasing focus of designers and owners in the underground construction industry. Many owners have expanded their requirements for durability design, with specific requirements for structure lifecycle and designer certification of structural durability. This paper describes current trends and best practices including: defining the underground structure lifecycle, historically durable underground structures, design methods for underground structure durability built of reinforced concrete, and durability of materials. Criteria to be used for defining end of structure life and owner’s maintenance responsibilities are crucial to lifecycle contract requirements. Current practices of several major owners are presented. Design methods are presented including United States code requirements. Current best practices for enhancing the durability of materials used in underground construction are discussed including: low permeability concrete, steel reinforcement concrete cover, the use of steel fiber, and testing for verification. INTRODUCTION Durability design is increasingly being recognized as an essential component of good design practice. Infrastructure owners recognize that to serve the public interest, constructed facilities must be lasting and durable. The public understands that structures with limited service life result in increased costs and add to their daily inconvenience with frequent repair and reconstruction. Engineers are increasingly asking not only is the structure strong enough but will it last for generations. Durability design requirements are no longer just adherence to some accepted practices, but are based on analytical approaches, with results that can challenge our beliefs in what construction materials and details result in a durable structure. This paper describes current industry requirements and practices for durability design of underground structures, and offers some suggestions regarding future trends and developments. SERVICE LIFE DEFINITION The service life of a structure is the sum of the time to onset of deterioration, called initiation period (ti), and the subsequent time period of deterioration ending when the structure is no longer functional, called propagation period (tp). Figure 1 shows a conceptual service life diagram. These time periods can be substantially affected by the level of maintenance performed during the life of the structure."

Jan 1, 2016

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989

By A. Martikainen

Field tests concerning a fog mesh method for fog removal are discussed. The first tests were performed at the Pyhäsalmi Mine, Finland. As this study gave promising results, further studies were completed at the Orivesi Mine. The results of these most recent field tests are presented and the two studies are compared. The Orivesi test set consisted of four materials. These included air filter fabric, fibrous filter fabric, a plastic greenhouse mesh, and an aluminium mosquito net. The variation of the Orivesi results was more noticeable than what was found previously. The best fog removal effect of all tests was achieved with the aluminium mosquito net, while the plastic green-house mesh performed worst. The humidity reduction by aluminium net was more profound than any of its precedents. More mesh materials will be tested in the near future.

Jan 1, 2007

By M. N. Chandraprabha

This paper discusses the role of mineral-adapted acidiphilic microorganism Acidithiobacillus ferrooxidans on the beneficiation of arsenopyrite containing multisulfides (pyrite and chalcopyrite). Adaptation to minerals altered the surface properties of the microorganism. Bacterial adaptation to arsenopyrite and controlled bacterial adhesion to mineral surfaces lead to selectivity in arsenopyrite separation. Bioremoval of arsenic ions (both arsenite and arsenate ions) by Acidithiobacillus ferrooxidans is also discussed.

Jan 1, 2009

In the present study, we have investigated the conditions for the formation of bubble clusters and the effect of well-defined agitation on the stability of clusters. A specially designed cell was used in which bubble clusters could be formed at the surface of a porous block in a fluidized bed of relatively coarse hydrophobic silica particles. The clusters then rose through a flow field of known turbulent characteristics. The size of the clusters before and after passing through the turbulent zone were measured using a high speed camera. The influence of shear rate on the deformation of the bubble clusters was investigated. The results showed that the Kolmogarov microscale was much smaller than the maximum cluster size, suggesting that the breakage of the clusters was mainly due to interaction with clusters in the inertial convection sub-range.

Jan 1, 2009

By Andy Alder

The aim of this paper is to provide an overview and details of good practice, from a United Kingdom perspective, in the development and implementation of major tunnel and underground infrastructure projects. In doing so, it draws on a broad base of project management theory. A central theme is that successful project delivery is dependent on detailed planning of the complete project delivery process, forming an effective team that works well together and the proper management of risk. The role of partnering in forming a strong project coalition is described. Particular emphasis is given to the integration of design and construction, and the role of the designer throughout the construction phase. The implementation of risk management in the design and construction of tunnel works is discussed, and recommendations are made on how risk, value and constructability can be integrated in project delivery. Recent practice in project procurement, particularly in the use of innovative collaborative forms of contract are described, and details of particular provisions for joint management of risk and problem resolution are provided. Finally, the relevance of the ITIG Code of Practice for Risk Management of Tunnel Works to good practice in project delivery is highlighted throughout the paper.

By Y. Wang

China is a big mining country with a long mining tradition and history. At present, there are nearly 200,000 different mines and 21 million workers. The total production value of mining makes up 6% of GNP. With the development of economy, the mining industry has played a more important role in our economic market, supplying more than 95% non-reusable energy, 85% of industrial and agricultural raw materials, over 75% of fertilizers and 30% industrial and agricultural water.

Jan 1, 2001

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By C. S. Wageman

Staying competitive in the highly aggressive Powder River Basin is a challenge facing all operators. Any advantage that a mine utilizes to improve productivity and reduce costs could mean the difference in the tight spot coal market. Technological advances in mining equipment and data acquisition at the Eagle Butte Mine in Gillette, Wyoming result in productivity gains and increased maintenance awareness. A new overburden haulage truck fleet with an onboard payload and fault monitoring system interacts via telemetry with the loading shovel and PC's located in production and maintenance offices, enabling staff to monitor production and maintenance on a real-time basis. This paper will describe the system and highlight the benefits realized as a result of its implementation.

Jan 1, 1996

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By M. C. Roberts

Currently, mineral producers are suffering through a major downturn in prices for their products, even though it has only been a few years since they were enjoying high prices. From an historical perspective, the current situation is another of the cyclical down-turns that often reoccur every 5 to 7 years or so. This paper uses time trend decomposition techniques to identify the cycles and statistical methods to find the duration of these cycles for a variety of mineral prices. Given some idea of how long and severe these cycles typically are, the mining industry can better plan to weather the downturns and take advantage of the upturns. For example, timing investments in new projects to take advantage of the cyclical upturns can dramatically improve project profitability.

Jan 1, 2000

By J. Winterton

Cripple Creek and Victor Gold Mining Co. is developing a full-scale pad injection program as part of the overall operational plan for the Valley Leach Facility. As part of the development process the mechanics of the injection methodology are evaluated in the context of physical injection measurements, outcome from geophysical monitoring, and gold leaching theory. The results indicate that hydraulic fracturing analogies advanced heretofore do not accurately describe injection phenomena in unconsolidated and noncohesive material typical of leach pads. A new interpretation is presented and extended to define operational strategies for maximizing gold production.

Feb 27, 2013

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000