Search Documents

By S. Assemi

Interaction forces between a hydrophilic silica particle and an air bubble were measured by atomic force microscopy using simplified model systems with deionized water and dilute KCl solutions. Contributions from the hydrodynamic force were minimized by using a low piezo speed. Particle-bubble separation distance and the bubble spring constant were calculated from linear regression of the piezo extension versus cantilever deflection. The bubble surface potential was then estimated from fitting the AFM-measured forces to the Hogg-Healy-Fuerstenau (HHF) model, using the surface element integration (SEI) method. Surface potentials obtained for the bubble at a low applied force were comparable with the literature data, suggesting that the simplified model used here can give a reasonable estimation of the bubble surface potential under moderate applied forces. Interaction forces between a silica particle and an air bubble were also measured at different locations on the air bubble surface. The force curves obtained at the edges of the bubble fitted very well to the theoretical force curves regardless of the applied force, while curves obtained at the center and halfway to the center, were more difficult to fit, in particular at higher applied forces (> 13 nN), suggesting that force curves obtained at the edges of the air bubble might be less prone to deformation effects.

Jan 1, 2008

By J. L. Carr

Every year, severe injuries and fatalities occur when a miner is struck or pinned by a continuous mining machine, shuttle car, scoop or other piece of mobile mining equipment. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Although hundreds of these systems are installed and in use in operating coal mines, the influence that coal has on the electromagnetic fields associated with these systems has never been rigorously quantified. NIOSH researchers have conducted tests to measure whether the proximity of coal has a significant influence on a popular design of proximity detection system. The system tested utilizes a low frequency magnetic field generator that would be mounted on the mining machine. At the NIOSH Safety Research Coal Mine in Pittsburgh, researchers measured the performance of a simplified proximity detection system of this type first on the surface then underground at varying distances from a coal face. Analysis of these measurements shows that the presence of coal does not have a measurable impact. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By J. P. Brady

A major spontaneous combustion incident occurred in the sealed goaf of the SL3 Panel; Southland Colliery in 2003 resulting in the loss of a longwall and sealing of the mine. The most important issue for the new owners, Yancoal Australia Pty. Ltd, was to effectively manage the atmosphere in the fire affected sealed area. This atmosphere comprised of flammable gases, the products of combustion and excessive levels of oxygen due to pressure differentials across the panel isolation seals with a potential ignition source associated with the residual spontaneous combustion event. The challenges were met in the first instance by the erection of pressure balance chambers with limited success. The problem was not solved until the pressure chambers were pressurized using a Floxal Nitrogen Plant supplied by Air Liquide Australia. Given the success of this approach on a small scale, a higher capacity Air Liquide Floxal Unit was acquired to manage spontaneous combustion at the recommencement of longwall mining operations. This provided the ability to pressurize pressure chambers that were installed in the Maingate Seals behind the face of the adjacent Longwall Block effectively preventing the ingress of oxygen and permitting the goaf to self inert in a reasonable time period. This paper summarizes a new proactive method of mitigating the risks associated with active and sealed goaves. Proactive management of these areas using low flow nitrogen into pressure chambers to maintain a positive pressure has eliminated typical reliance in explosion proof or explosion resistance seals as the primary control.

Jan 1, 2009

By S. S. Sephton

Sintering as applied to agglomeration of ferrous fines has shown little growth in the United States in recent years. The general concensus was that most of the existing facilities would remain in production at a reduced tonnage to dispose of and recover solid waste from steel plants. Further growth for ferrous sintering technology was not in sight in the United States and in the early sixties expansion came to a virtual standstill, however, we witnessed a rapid emergence of a tremendous pelletizing industry. On other continents, due to different raw materials supply and capital structure, sintering technology continued to grow, with a more cautious development of pelletizing installations. In the U.S. the diminishing supply of good quality, high grade coarse ore resulted in eventual disappearance of high grade ore fines for sintering. The finely divided concentrates produced from lower grade ores were not amenable to this type of agglomeration, but were more suitable for pelletizing. Furthermore, pellets seemed to possess all the features of an ideal blast furnace feed; namely pellets are free flowing, uniform in size, strong, with extremely uniform chemical composition and good reducibility. Importance and demand for such well stabilized furnace feed further increased as size of newly installed blast furnaces continued to grow. The in- creasing demand for a uniform, stabilized burden coincided with the effort to produce a fully beneficiated burden for smelting, thus reverting the blast furnace to its primary function of smelting.

Jan 1, 1973

The ability to track miners and communicate with them while they work in underground coal mines is important during normal daily operation, and critical in emergency conditions. This was evident during recent incidents at underground coal mines worldwide. Communication with miners and the knowledge of their location is of great importance for rescue efforts and the preservation of life. Numerous technologies have been developed, adapted and deployed to meet tracking requirements of the Mine Improvement and New Emergency Response (MINER) Act of 2006. Evaluating the performance of these systems has proven to be dif?cult for mine operators, system manufacturers and regulatory agencies. The MINER Act requires operators to improve accident preparedness by developing an emergency response plan speci?c to each mine. With the recent implementation of the provisions of the MINER Act of 2006, all underground coal mines in the United States are subject to the mandates of legislation concerning communication and tracking system installation. As of June 2011, 203 new or revised tracking and/or communication systems had been approved by the U.S. Mine Safety and Health Administration (MSHA), with nearly 50 other systems or revisions in the approval process (MSHA, 2011). At that time, the available approved systems for underground coal mine use included these types: ? Leaky feeder communication systems. ? Fixed node-based communications and/or tracking systems. ? Wireless node-based communications and/or tracking systems. ? Medium frequency (MF) communication systems. ? Communication system peripherals. Other types of tracking systems have since been developed and some manufacturers are seeking approval for use in this application. Some of the new products include through-the-earth (TTE) systems and various radio frequency (RF) adaptations. New technologies that are currently being developed and deployed in other industrial applications should also be considered, including acoustical, optical, inertial and hybrid technologies. To date, no uniform method has been employed in the industry to effectively compare and evaluate the performance of installed systems. Neither industry operators nor regulatory agencies can accurately assess the capabilities of installed systems in the continuously changing mine environment. There is a need for a uniform evaluation method that provides the ability to assess how different systems and technologies perform in various mining applications, and whether they can satisfy the regulatory requirements.

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level. It is situated in a wide east-west valley. Minera Peñasquito, S.A. de C.V., wholly owned subsidiary of Goldcorp Inc. has operated twin SABC-flotation lines since June 2010. Each line is capable of processing 50,000 tonne per day using a SABC grinding circuit followed by flotation to produce lead and zinc concentrates. The addition of a Polysius Polycom HPGR 2417 with dual 3,000 kW drives to reduce the crushed pebbles produced by the SAG mills was planned to increase production to 65,000 tonne per day per line. The production has been limited to 100,000 tpd due to operating issues in the grinding circuit. The operating issue has been the amount of pebbles generated by the SAG mills is significantly less than originally planned. This paper describes the planned installation of a crushed augmented feed to maximize utilization of the HPGR capacity. This coupled with full utilization of the SAG and Ball Mill available energies there is the potential to achieve a 50% total capacity increase from the grinding circuit.

Jan 1, 2012

By G. Daws, N. Woodward, A. Oxley

Many mines around the world have been seeking ways to achieve sustainable developments and reduce operating costs. Rockbolting is a technology that needs to be considered as it provides a means of reducing operating costs and improving safety whilst allowing improved production to be achieved. The problem is how to introduce this technology in the knowledge that a successful outcome will be achieved. Rockbolting is a complete package and not only includes the consumable materials but also training, production of Codes of Practice, Monitoring Schemes, Refinement of Design and long term management of the systems. This paper explains the methods that have been applied for its successful introduction and discusses several case studies. It does not give fine detail but is intended to allow decision makers to gain a basic understanding of the method used to successfully introduce rockbolting to a mine.

Jan 1, 2011

By G. W. Johnston

INTRODUCTION For many years mining at the Stobie mine of the Inco Metals Co. consisted mainly of fill-type mining for higher grade ores and block caving or blasthole open stope mining for lower grade ores. Open stope mining, although quite favorable in the initial stoping phase, has always presented problems in the pillar recovery phase, especially at depth. In 1966, sublevel caving was introduced. This method is ideally suited for low-grade ore and can be applied very successfully to intermediate or higher grade ores providing proper controls are enforced. Sublevel caving has three distinct advantages: it is highly adaptable to mechanization; it recovers the ore in one operation; and it provides adequate ground sup¬port and safety regardless of mining depth. This method does, however, make extra demands, particularly for new types of supporting services. The constant presence of rock makes quality control of the grade of the ore being extracted essential. Increased de¬velopment, different types of ventilation, roadways, and maintenance are only a few of the many changes re¬quired. The care and maintenance of the fleets of diesel equipment and the modification of equipment is a con¬stant challenge. CHOICE OF SUBLEVEL CAVING The question arises, why mine by sublevel caving? Fig. 1 shows a typical problem encountered by the open stope or blasthole mining method. Near the surface there is little or no ground support problem. As mining progresses to an intermediate depth, however, ground failure starts to occur in the supporting pillars. If open mining is carried beyond this point, the critical depth is soon reached, accompanied by hanging wall caving, ex¬tensive pillar failure, and the danger of losing control of the mining cycle. The rock caved from the hanging wall mixes with and dilutes the ore being extracted from the blasthole stopes. Ore losses occur when pillar failure pre¬vents drilling and development of part of the ore. The interruption to the mining cycle causes serious curtail¬ment in production until ground failure is controlled and the mining method changed to adapt to the new conditions. Having recognized the limitations of open stope min¬ing, alternatives were sought. The first alternative (Fig. 2) was to fill the open stopes with sand fill be¬fore extensive pillar deterioration occurred, recover the pillar ore by fill mining, and then convert to total fill mining below. If the ore grade is high enough it can support the costly fill method. Recovery will be at a much slower rate and will therefore extend over a longer period of time. On the other hand, sublevel caving gives complete primary mining recovery in a short time and is very adaptable to mechanization, which is now a necessity to combat spiralling labor costs and give greater produc¬tivity per man. Sublevel caving is ideally suited as a mining method for low-grade ore bodies which eventually reach a criti¬cal depth for open stope mining. DEVELOPMENT The development phase comes first and of course its main purpose is to gain access to the ore and provide a route for ore removal from the mine. Initially a 20% inclined service ramp is driven in the footwall rock (Figs. 3, 4, and 5). It is preferable to start at the top of a mining block and drive the ramp down¬ grade so gravity can assist in mucking the blasted de¬velopment round, and also access can be gained more quickly to the initial production area. The ramp nor¬mally turns at 3.1 rad (180°) about every 152.4 m (500 ft) to keep it reasonably close to the rock disposal

Jan 1, 1982

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By S. M. Smouse

Total world energy consumption is projected to continue its strong growth of recent years. Because coal is the most abundant fossil fuel, it will likely remain an important energy source, particularly for power generation, into at least the early years of the next millennium. Clean coal technologies are available today that can economically reduce air pollution, primarily SO2 NOx and particulates, and for the higher efficiency technologies, CO2, from power generation. U.S. Department of Energy analyses show that the adoption of clean coal technologies could decrease carbon emissions worldwide while creating a strong export market with attendant creation of jobs in the U.S.

Jan 1, 1998

By M. G. Eiselein, R. A. Smith, C. H. Sheerin

FMC Gold's Paradise Peak Mine was one of the top two producers of mercury metal in North America in 1988 and 1989. As a by-product, elemental mercury is produced from cyanide soluble mercury minerals, primarily to reduce the health risks incurred with the refining of precious metal precipitate containing elemental mercury and mercury amalgams. A discussion of the design, primarily the Merrill-Crowe units, and permitting for the safe production of mercury will be presented. Additionally, laboratory testwork to determine the effect of mercury on reagent requirements in the Merrill-Crowe process will be discussed.

Jan 1, 1990

There are multiple stages in a mining operation that a mining engineer has to draw polygons to be used as operation guidelines. These polygons are drawn by hand and based on engineer?s experience. However, having automatic procedures for forming the shapes can increase the quality and decrease the efforts required. These shapes need to be homogenous in grades and rock types so that the quality and dilution of material sent to the plant can be estimated with the good approximation. In this paper, a clustering algorithm with shape control is introduced which can provide reasonable guidelines for all the aforementioned shapes by manipulating its parameters. At the end, implementations of the algorithm on a small part of a gold deposit with different mining strategies is presented and evaluated based on homogeneity of grade, rock types and determined destinations as well as the shape.

Feb 27, 2013

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968

By M. Z. A. Bakar

To investigate the differences in the radial drag pick cutting performance in dry and saturated sandstone, a suite of linear rock cutting test was performed using linear rock cutting machine (LRCM). Experimental results of 50 data passes, incorporating 350 data cuts were used to compute cutting, normal and side forces required for determination of other performance related parameters. Although the forces required to cut the dry and saturated rock were in congruence for most of the spacing and depths of cut combinations; but the overall averaged cutting and normal forces for saturated rock cutting were found to be 9.9% and 9.4% respectively higher than the dry rock cutting. The increase in the overall averaged forces was attributed to strength variability of one of the saturated block affecting the overall forces. The side forces experienced a negligible drop in saturated rock cutting. An increase of 28% and 9% in the actual and nominal specific energy values respectively was also recorded when cutting saturated rock as compared to the dry rock cutting. The increase in saturated rock specific energy is attributed to production of large amount of fines and few large sized chips directly contributing towards increase in specific energy. The optimum s/d ratio for dry rock tests was found to lie between 6 and 8 whereas for saturated rock cuts this value lied between 5 and 9.

Jan 1, 2012

By M. M. Gadde

Recent regulatory changes in the United States make it mandatory to conduct structural analysis of coal mine seals used to isolate abandoned workings from active mining areas. Different loading criteria are available for seal design depending on whether gob composition is actively monitored and maintained or not and whether the gob conditions lead to deflagration or detonation type loading. Since the loads involved in seal designs are dynamic in nature, the structural analysis must be made using dynamic stress analysis techniques. However, because of the significant complexities involved in conducting dynamic analyses, some designers use approximate simplified techniques to address the design problem. In this paper two such simplified methods are critically evaluated for their suitability to design coal mine seals. The benefits and limitations of the simplified methods are also outlined. Some comparisons are made to show the differences between sophisticated three dimensional dynamic analyses and the simplified methods and to delineate the problems associated with the latter approaches.

Jan 1, 2009

By D Beahm

Introduction The Energy Metals Corporation (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin including the JAB Property, one of several potential properties being planned for development as a satellite facility to the greater Antelope Uranium Project. A National Instrument 43-101 Technical Report has been completed for the JAB property. This report estimates total measured and indicated mineral resources on the property totaling 3,555,022 pounds U3O8 contained in 2,400,875 tons at an average grade of 0.073 % U3O8 at a .25 GT cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB Property is located in Sections 13, 14, 15, 16, 21, 22, and 23, Township 26 North, Range 94 West, approximately Latitude 42o 14’ North and Longitude 108o 00’ West (Figure 1, Location Map). This property consists of unpatented mining lode claims and Wyoming State mineral leases comprising approximately 2,100 acres.

Jan 1, 2007

By R. Adsero

The analysis of equipment trends in AUSIMM?s Revision of Monograph 19; Australasian Mining and Metallurgy Operating Practices (AMMOP) in the paper by Dight et al (in press) raised some interesting and in parts disturbing trends in the Open Cut Mining Industry. According to the US Bureau of Labour Statistics the US mining and petroleum industries? productivity is down by 12% since 2004 while the Australian Bureau of Statistics shows the productivity of the Australian mining industry is down by 34% since 2001. In terms of open cut equipment median output for draglines is down by 15% since 2003; electric rope shovels are down by 41% since 2003; hydraulic excavators are down by 39% since 2008; front end loaders are down by 39% since 2007 and trucks are down by 41% since 2006. Clearly the boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top 10% by annual output per unit of input) has declined but not by as much as the median (eg. shovels down by 8%, excavators down by 19% and FEL?s down by 5%). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one will be crucial to reversing the decline in open cut equipment performance.

Feb 27, 2013

By Steve Kral

The timing was right for SME to celebrate its 50th anniversary in February as a member society of AIME. The mining industry is in the midst of a commodities boom that appears to have legs. Not only is the demand for metals, construction materials and the like increasing in developing nations, but developed nations have also seen the demand for those materials increase at impressive rates. So, in addition to networking and seeing old friends, attendees at the SME Annual Meeting and Exhibit in Denver, CO. Feb. 25-28, had several reasons to enjoy the week — a healthy industry and their society’s landmark anniversary. This annual meeting was held jointly with the Colorado Mining Association’s (CMA) 109th National Western Mining Conference.

Jan 1, 2007

By H. Walqui

This paper describes operating gains resulting from standardizing operating and maintenance practices to improve the performance of the pebble crushing circuit at he Empire Concentrator. Past efforts have led to improved operating time but no additional throughput gains. New Operating standards and checklists were developed and introduced. The content and frequency of the review process indicators was then changed to take advantage of the new practices resulting in an increased feed rate and availability through the pebble crushing circuit.

Feb 27, 2013

By J. S. Stachulak

The Diesel Emissions Evaluation Program (DEEP), a research consortium formed in 1997 by Canadian mining companies, labour unions, and provincial and federal government departments, completed its work by mid-2006. This program, in which Vale Inco participated with both direct funding and in-kind contributions, investigated the ability of currently available technology to significantly reduce underground concentrations of diesel particulate matter (DPM) with high efficiency and low maintenance over a long-term period (years of life).While DEEP?s testing showed that engine maintenance is a critical component for lowering DPM, it was clear that reduction of DPM to the very low target levels of ~0.05 mg/m3 was not possible with maintenance alone. The best candidate technology for achieving low DPM levels was particulate filter systems. Furthermore, successful deployment of such systems was highly dependent on removing them from having to rely on human intervention for their regeneration. The search continues within Vale Inco to identify a reliable and rugged system.

Jan 1, 2009