Search Documents

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

By A. J. Vietti

"Drought conditions and the possible lack of sufficient raw water supply are a constant reminder to the Southern African diamond miner of the need to minimize raw (new) water input while maintaining or expanding mine throughput.Since water input volume is directly related to water output (loss) volume, mainly to the tailings, it is obviously beneficial to dewater the tailings as much as possible. However, this may not always be as easily achieved as first thought. Owing to the unique mineralogy of each kimberlite deposit and the unique chemical profile of each raw water source, dewatering of the slurry is not a standard process that can be applied equally across the entire diamond industry.This paper presents a first-step strategy that kimberlite diamond mine operators should consider and apply to meet and exceed their watersaving targets. Introduction A common metric for measuring water use efficiency in a metallurgical plant is the amount of raw water used per ton of head feed treated (m3/t). The metric includes all water recycled from the dewatering process and from the tailings storage facility (TSF), and the only inputs are tons of ROM ore and cubic metres of raw water make-up to replace water lost to evaporation, seepage, and lock-up at the TSF (Figure 1).The volume of new raw water available to the process is not unlimited and a maximum monthly allowance is typically set during the mine permitting process. Consequently, if the volume of water lost exceeds the volume of new water available or alternatively, in times of drought where the allowable volume is unavailable, the plant has no other option but to reduce throughput.However, if the plant operator is able reduce the volume of water lost to the TSF, the plant will have additional capacity to either increase tonnage throughput or sustain nameplate capacity during periods of severe drought. The obvious conclusion, therefore, is to reduce the volume of water lost to the tailings by improving the efficiency of the dewatering process (typically gravity thickening) simply by increasing the density of the tailings being discharged. In practice, however, the unique mineralogy of each kimberlite deposit and the chemical profile of the raw water source used imply that at some mine sites, solid/liquid separation (or settling) of tailings slurries at the dewatering process is more easily achieved than at others. In these cases, simple practical steps such as firstly improving the flocculant reagent make-up and dosing control, and secondly focusing on thickener discharge control, are the only requirements for enhancing water recovery at the dewatering circuit. At other mine sites however, solid/liquid separation of the tailings may not be achieved at all, in which case efforts to increase water recovery by improving reagent dosage and thickener control would be fruitless unless the colloidal properties of the thickener feed slurry are modified."

Feb 1, 2019

By R. Burger, M. Masukawa

Cato Ridge Alloys (CRA) is a joint venture company between Assmang of South Africa, Mizushima Ferro Alloy Company (MZK) and Sumitomo Corporation from Japan. Negotiations for the formation of the company started in 1992 with the joint venture agreement signed on the 19th September 1996. MZK was to supply the technical know how for the production of Medium and Low Carbon FeMn while Assmang was to manage the day to day activities of the company. Sumitomo Corporation was to act as facilitator between Assmang and MZK and, together with Ore and Metal are responsible for the marketing of the refined products. The conceptual design of the plant started in December 1996 and the first charge of molten high carbon ferromanganese metal was charged on the 19th January 1998. Problems experienced during the initial startup period were addressed resulting in substantial operational improvements. A build-up in the stock of fine metal was addressed through the development of a process to remelt the fine metal, the development of a market for fine metal and the upgrading of the crushing and screening plant to reduce the generation of fine metal. The mass yield from High Carbon Ferromanganese to Refined Ferromanganese was increased through the implementation of statistical process control, changes to the blowing patterns and the development of a sampling device for taking samples during the process. Converter refractory consumption was reduced. This was achieved on the converter by improving the cooling of the converters with the installation of cooling fans and cooling fins. The heating schedule of the converters was changed for improved refractory life. Production schedules were modified to allow cooling of the refractory between low carbon erromanganese charges. Additional changes made to improve operations were: ? Changing from mehanite casting trays to metal fines beds. ? Installation of sonic horns in the baghouse to prevent the bridging of dust. ? Improved welding on the lance tips.

Jan 1, 2004

By D. G. Krige

Using chip sample data and spatial structure parameters from a large mined-out section of a South African gold mine the advantages to be gained from a regular underground borehole drilling programme have been investigated for short- and medium- to long-term planning based on block valuations. The results have been compared with the current position, which relies invariably on the extrapolation of limited peripheral sampling data from raises, gullies or stope faces. Some preliminary work has also been done regarding the implications of such underground drilling on costs used for the present pay limit calculations. The results of the study, though preliminary, show that the net advantage of advance regular underground drilling could be substantial and that a more intensive follow-up research is warranted.

Jan 1, 2003

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By H. Preßlinger, H. Hiebler, K. Klepp, W. Posch, M. Mayr

It was investigated in which form sulphur is bonded in ladle slags. For this purpose, the mineralogical phases of the ladle slags were qualitatively and quantitatively evaluated by means of a microprobe. This slag characterization allowed reconstructing the bonding of sulphur into the phases of the ladle slag. Moreover, the reaction process with regard to the ionic theory as well as the structural formula for the mechanism of sulphur bonding were discussed. The bonding of sulphur into calcium aluminate slags is determined by the sulphide ion content in the slag as well as by the ratio of (CaO)/(Al2O3). Calcium sulphide separates only if the slag contains a large number of sulphide ions. When Ca12Al14O33is separated, the sulphide ion is successively integrated into the lattice. The crystal lattice of Ca12Al14O33is characterized by an open, three-dimensional anionic network composed of aluminium-oxygen tetrahedrons linking the edges. In this network, large interstitial spaces are formed, which may be filled with calcium ions on the one hand and statistically with a free oxygen or sulphide ion on the other hand. Key Words: ladle slag, structure, phases, calcium sulphide, calcium aluminate, desulphurization

Jan 1, 2004

By S. R. Sankaranarayanan, T. Sowmya

Slags and fluxes used in metallurgical processes are typically made up of oxides (especially silicates), with additions of fluoride and carbonaceous matter. Despite the efforts made towards understanding the role of slags in various processes, little information is available on the structure of these slags. Tools such as X-ray diffraction, spectroscopy, and electron microscopy could be used for this purpose. This paper is based on an ongoing spectroscopic and structural investigation of slags and related materials. Spectroscopic studies of various commercial slags (predominantly ferrous), ores, glass and related materials, covering a wide range of compositions, have been carried out to understand the structure. The infrared spectra were recorded, predominantly, using FTIR spectrometer (Bruker IFS 66U) spanning 4000 to 100 cm-1using the KBr pellet method. The resolution was typically 4 cm-1. The spectral outputs have been compiled in terms of bands present (corresponding to different bonds) and then compared with the typical bands expected for such bonds. Efforts are in progress to identify the trends with respect to the chemical composition?for example, the effects of SiO2, Al2O3, and non-bridging oxygens. Data obtained so far indicate some trends such as (i) a shift in the Si-O band (969 to 1099 cm-1) towards a higher wave number with increasing silica content (almost 2 to 92 weight percentage) and (ii) further strong shifts as a function of the alumina content. These are being further investigated structurally and in terms of chemical composition/parameters. Keywords: slags, silicates, structure, spectroscopic analysis, shifting of bands

Jan 1, 2004

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By W. Bryszewski

As a result of strategic analysis in respect of the needs for air quality management a new advanced and holistic approach to air quality management process was introduced in the North West Province (NWP) of South Africa. The process is based on the principle of co-operative management. It involves both active participation of all Interested and Affected Parties (I&AP) and the holistic approach to solving problems with the underlying principles of shared ownership and sustainable development. The process consists of the followings phases: ? Industrial process quantification ? Quantification of impacts ? Formulation of the required control measures ? Definitions of certificate conditions ? Implementation of an adequate compliance management system at company level ? Ongoing co-operative air quality and system management with the strategic objective of continuous improvements The system has been successfully introduced in the North Province and proved to be an effective management tool and aids assurance of sustained environmental ability to cope with the pressure of industrial developments. The benefits and effectiveness are discussed using Hernic Ferrochrome as an example. Hernic Ferrochrome is one of the first companies, which successfully implemented this system.

Jan 1, 2004

By R. Boom, J. Halder, B. Snoeijer, B. Deo, A. Overbosch

Operational data of BOF and the slag samples for different starting conditions of phosphorus(0.06–0.26 per cent P) and silicon content (0.3–1.2 per cent Si) of hot metal have been analysed. The contribution of parameters that are well known to affect phosphorus distribution at tap, like basicity, temperature, FeO content of slag, slag mass etc., is investigated through the models of ionic theory of slag, optical basicity, regular solution approach and molecular theory of slag. The best overall results are obtained by the model based on molecular theory of slag in which several operational parameters are also incorporated. The investigations of different slag samples, based on optical, SEM, EPMA and X-ray studies, reveal the effect of MgO and Al2O3on slag morphology and phosphorus distribution in different phases. It is important to consider phosphorus distribution ratio in the solid and liquid part of slag. The solid part of slag, which is mostly dicalciumsilicate, can contain up to 5 per cent phosphorus. The phosphorus content of the liquid part of slag may depend upon the phosphorus content of hot metal or phosphorus load of slag. It is found that incorporation of effect of dicalciumsilicate in the model improves the accuracy of prediction. For better process control, the addition of iron ore towards the end of blow must be avoided while treating high phosphorus hot metal or during the production of ultra low phosphorus steels. Keywords: steelmaking, BOF, phosphorus distribution, slag morphology, MgO, Al2O3,dicalciumsilicate, process control, models

Jan 1, 2004

By B. Genc

"The risk of spontaneous combustion is well known in the South African coal mining industry. In the coming years it is very possible that the incidence of spontaneous combustion will increase from current levels, due to factors such as an increased rate of mining, re-working of previously mined seams, more stooping and total extraction for underground mines, and higher stripping ratios for surface mines, leading to more spoils. It is also fairly certain that coal mining will face tougher environmental emissions legislation in the near future. To determine the areas where the risks of spontaneous combustion are high, it is necessary to improve on our current laboratory procedures for testing and evaluating coal samples, combining the results with site and field data, and if necessary revising the laboratory rating system to refine our understanding of South African conditions.Currently, laboratory tests are conducted in order to determine both the Wits-EHAC index and the crossing-point temperature which, when combined, give an indication of the spontaneous combustion propensities of the coal samples. This procedure has enabled the establishment of a database of results to review and evaluate South African coal seams. Using this database, the high-risk areas in terms of spontaneous combustion are identified. Tests have been undertaken for five consecutive years, between 2008 and 2012. In total, 119 coal samples from different coal seams and production coalfields have been analysed and classified through a series of laboratory tests. A comprehensive database of these results is available, and is continually being updated as new test results are added. This database will continue to expand, and to provide the basis for an improved risk evaluation methodology for spontaneous combustion"

Jan 1, 2015

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

By C. C. Pretorius

3D seismic surveys have become a well-accepted method of imaging sub-surface geology in the Bushveld Basin. Because both the seismic sources and receivers are placed at surface, most surveys are limited to imaging faults with >=7 m throw. However, some areas such as shaft infrastructure can benefit from the ability to detect smaller structures prior to shaft sinking. Borehole radar and logs such as the acoustic televiewer can identify these structures in the shaft barrel, but not within -200 m from the shaft. Therefore, Anglo Platinum has developed the method of high-resolution 3D vertical seismic profiles (VSPs) for structural sterilization of shaft sites prior to shaft sinking. VSPs utilize a surface source and sub-surface receivers deployed down a borehole. This means that seismic energy goes through the near surface only once, and therefore suffers less frequency loss than when both source and receivers are on surface. Furthermore, VSPs can record 3 component (3C) data which comprises P wave, Sh (horizontal) and Sv (vertical) wavemodes. Because S waves travel at about 0.6 of the velocity of a P wave, shorter wavelengths and therefore higher resolutions are possible using S wave data. VSPs were first used in their one dimensional, zero offset, mode to correlate borehole geology with seismic stratigraphy within seismic surveys. This showed that VSPs record -30% higher frequencies than surface seismic surveys. The program then applied two dimensional VSPs to the problem of imaging geological structure close to a borehole. 2D VSPs confirmed that high frequency results could be achieved, and that this enabled a more accurate image of the Merensky Reef than could be achieved by surface seismic data. Finally, the program has achieved the successful recording and processing of 3D VSP data, with both compressional and shear wavemodes giving a high resolution structural result. Although P wave data gives -30% frequency improvement over surface seismic surveys, S wave data can give as much as 80% improvement, further improving the structural image achieved. The high fixed costs of VSP surveys mean that they should ideally be run in multi-client batches, which can reduce the per borehole cost by up to 50%. Their application is anticipated to be on high value capital infrastructure with a geological risk from faults which are not imaged by surface seismics-generally in the sub-7 m range. Keywords VSP, 3D seismic, bushveld, platinum, resolution, imaging, shear waves, shaft sinking.

Jan 1, 2011

By C. -J. Rick

By implementing a converter downstream of the reduction furnace it is possible to broaden the product range significantly. The converter can also successfully be used to strip furnace slag from chromium oxide. Some process alternatives and their economical, practical and environmental implications are studied using process models developed based on UHT?s long experience in stainless steelmaking, stainless steel process control and charge chrome refining. Keywords Charge chrome, converter refining, ferrochromium products, process design.

Jan 1, 2010

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014

By J. Saunders, N. Pretorius, G. Krafft, T. P. Katakwa

Imagine being able to see all the future planned mining activities in real time. This is exactly what SIMS (Short Interval Management System) will enable you to do. SIMS is a real time short interval control system that continuously measures and sets optimised plans for mining production processes. The system utilises algorithm-based software that takes resources (people, equipment, tasks, and workplaces) and gives you the best achievable plan. The algorithm was developed using methods found in the field of metaheuristics. A metaheuristic is a strategy to designed to efficiently search for optimal or near optimal solutions to problems that are very complex computationally. (Glover, 1986) There are several algorithms that have been developed to solve optimisation problems which are difficult to solve using traditional techniques. This has given rise to a field called evolutionary computing. (Simon, 2013) Examples of these techniques are genetic algorithms, particle swarm optimisation, and ant colony optimisation. These methods are used to solve problems in a variety of fields. As an example, Kok and Lane (2012) used particle swarm optimisation for equipment allocation in a mechanised underground mining environment. The first SIMS deployment took place in a platinum underground tabular mechanised mine near Burgersfort (province?) from 2017-2019. This included the development from a paper-based system to a fully operational online system. SIMS then moved to a second site and is currently being tested in a second platinum underground tabular mechanised mine in South Africa. Full deployment of the system is currently being phased in. SIMS was built in response to issues that have been plaguing the mining industry for years. These issues are all aligned into one major problem statement: how can we optimise mining production processes without compromising safety? This product was developed by combining years of mining experience with software development. SIMS is based on a four-pillar concept. Safety, productivity, accountability, and business improvement. SIMS uses a set of pre-configured mining and production rules, and with the resources that are available, to determine valid short term production plans. A background algorithm then determines the optimum plan to be executed. The system continuously produces a set of job cards that are pushed to respective operators on their allocated tablets. The management portal component allows you to view and manage all current and planned work on any connected device available. This allows real time visibility of completed, current, and planned work to operators, service departments and management, i.e., seeing into the future.

Sep 1, 2021

By A. D. Storrie

An underground wet shotcrete trial was completed last year to determine the effectiveness of wet shotcrete as an alternative support mechanism to dry shotcrete in the kimberlite environment. The wet shotcrete was manufactured at the underground batch plants, transported to site using an agiecar and transferred to the shotcrete pump. The wet shotcrete is pumped to the nozzle where compressed air at 7 bar and an accelerator, Meyco SA 160, is added and enables the shotcrete to be placed successfully onto the tunnel wall. No tunnel guard was previously placed on the sidewall and hangingwall. Geotechnical testing indicates that the Grace fibre performed extremely well with the energy absorption tests at 7 kg/m3and 8kg/m3where both achieved over the mine requirement of 750joules. The Grace fibre and wet shotcrete mix also achieved a compressive strength in excess of 55 MPa, well above the 45 MPa requirement for Premier Mine. The recommended wet shotcrete mix design is therefore based upon: [Material/ CriteriaQuantity/m3Units ?Lafarge 42.5 Duratech500kg ?Condensed silica fume40kg ?Rayton Sand1.558Ton ?Delvocrete stabilizer 103.6litres ?Glenium 27CH5.4litres ?Meyco TCC 7355litres ?Water230litres ?Meyco SA16025litres ?Fibre8kg ?Cement/Water Ratio2.35? ?Water/Cement Ratio0.43? ?Flow615 mm] If the wet shotcrete system is implemented there is a potential for Premier Mine to make major savings. In South Africa there are two suitable wet shotcrete machines available for the mining industry, the Spreymec, manufactured by Tamrock and the Fermel/Meyco wet shotcrete machine. The Spreymec is a fully imported machine. The Fermel component is manufactured in South Africa and the Meyco shotcrete components are imported and supported by MBT (Master Builder Technologists) in South Africa. The Fermel/Meyco machine is assembled in South Africa. Premier Mine has allocated some R2, 100,000 towards the implementation of the wet shotcrete system. If implementation is successful there should be an internal rate of return gain of 76% with regard to this project.

Jan 1, 2001

By Vinay Kumar Agrawal, Rama Nath Praharaj

IMFA Group is the largest producer of Charge chrome not only in India but also in Asia. This Group has plants situated at Therubali and at Choudwar. They also have a Thermal power plant at Choudwar which not only caters to the power requirement of Choudwar plant but also supplies power to Therubali. The plants are fed for Chromite ore through the captive mines namely Nuasahi Chromite mines (40.47 Ha) , Bangur Chromite mines(37.34Ha), Sukinda chromite mines (116.76 Ha), Mahagiri Chromite Mine(73.777 Ha) and Chingudipal Chromite mines (26.62 Ha). Nuasahi Chromite Mine, which is situated in Keonjhar district, is an underground mine and is based upon best technological advancements in the industry. The underground mining operation is certified under ISO-9002, ISO-14001and OHSAS 18001. This not only shows the concern for the quality, environment but also for the health of the employees. The Nuashahi is the first chromite mine to backfill the opencast excavations created during the last 50 years and carry out the production from underground area below the opencast workings. This paper deals with the state of art technology of sub-level open stopping in thin ore bodies. The under-ground mine openings was started in the year 1997. In next four years the production of chromite from underground was started.(2001). At present the mine is in a good shape with several running stopes. Today it is producing around 10,000 Mt per month of chromite. The development of the mine is carried out with an average of 200 mtr per month of tunneling. The mine is having a mechanical ventilator having a capacity of24000 M3 per hour at 50mm water gauge, thus feeding sufficient air for the persons working in underground. The mine is being dewatered through a most modern positive suction sump, having a capacity of 500 cum and operated with 120 HP pumps. After commissioning of this sump in the year 2003, the mine has taken a quantum jump in production with remarkable saving in power consumption.

Jan 1, 2007