Search Documents

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran, J. Zoric

A methodology for building pragmatic physics-based models is here adapted to predict the erosion of ladle linings in the steel industry, in order to support operators when deciding whether the lining can be used safely for another heat. A defective lining may allow 140 t of molten steel to spill, with disastrous consequences for workers and plant. The adopted work flow for the development, challenges faced, and some model results are presented. One key learning outcome is that model development should allow time for maturing the process understanding, as well as for many iterations by ‘questions-responses and actions’ at various stages in the model development. Good interaction between the development team and industry case owner is an important success factor. Combining or extending the model with the use of machine learning and cognition-related methods, such as knowledge graphs and self-adaptive algorithms, is discussed.

Apr 16, 2024

By C. Snyman, M. Le Roux, Q. P. Campbell, S. Engelbrecht

Due to the ultrafine particle size required for effective processing of chromite ores, dewatering of the concentrates presents a challenge. It is not uncommon for the ore to have elevated moisture contents even after dewatering, which must be reduced to required levels of between 8% and 10% by mass for further processing. Contact sorption drying has shown promise in test work on fine coal. This method was used to study the dewatering of chromite on a laboratory scale using 3 mm spherical activated alumina ceramic beads as a sorbent. Three different sorbent-to-chromite mass ratios, namely 0.5:1, 1:1, and 2:1, were tested with different process conditions, including dewatering in a stationary and a rotatingl bed. The experimental work showed that it was possible to achieve the target moistures in less than 10 minutes, irrespective of the sorbent-to-chromite ratio used. Ratios of 1:1 or higher, however, proved to be the best. The sorbent reusability at mass ratios of 1:1 and 2:1 were therefore tested. With a 1:1 mass ratio, the sorbents could be reused for three cycles, while with 2:1 ratio, the number of cycles increased to six. The sorbent-to-chromite mass ratio used had a significant influence on the required contact time and the reusability of the sorbents.

Oct 3, 2023

By J. Petersen, M. Reuter, E. Asselin, M. Becker, N. Uys

In order to meet society’s ever-increasing demand for metals and address the numerous technical, economic and environmental challenges within the current mining context, a holistic approach to process design, which is grounded in mineralogy, is needed. This would ensure that the impact of varying process mineralogy (and associated chemistry) on technical considerations and the associated economic implications and environmental consequences are taken into account upfront. This investigation focuses on the commodity zinc due to its strategic value coupled with limited resource availability and the wide variety of substantially different process technologies in existence. As the most commonly processed zinc ores contain zinc sulphides, the mineralogy/chemistry of these ores and their associated process routes will be discussed. The findings have been generated through the analysis of two case studies, Teck’s Trail Operations (British Columbia, Canada) and Hudbay Minerals’ Flin Flon Operations (Manitoba, Canada). The flotation of zinc sulphide ores to produce concentrates with varying mineralogy, represents the starting point for both case studies. The hydrometallurgical process routes for the further refining of zinc and other valuable metals include roast-leach-electrowinning (RLE), and zinc pressure leaching (ZPL). The effect of process route choices on primary metal recovery (Zn), coproduction of other base metals (Cu, Pb), potential for other valuable metal production (Ag, Au) including less well known, but increasingly important trace elements (In, Ge), and the production of other by-products (H2SO4, S0) are discussed. The economic and environmental implications of these aspects will also be considered. It is concluded that a quantitative modelling approach must be taken where waste management is integrated into process system design and simulation as a key unit operation. Keywords: Zinc Sulphide Processing; Design Decisions; Mineralogy

Jan 1, 2020

By Roger A. Blais, Michel David

"Matheron's geoslalislical method for the estimation of ore reserves has been developed to the point at which real-life problem may be handled effectively. The steps involved in the method are:(i) obtalning the variogram,(ii) fitting a model, and(iii) producing block estimates.All three steps may cause difficulty, and would-be users need a deep understanding of the theory if failure is to be avoided.To illustrate these points, specific cause are considered:(i) two almost equidimensional porpbyry deposits, one drilled randomly and the other regularly; and(ii) two iron formation, one drilled extensively and being mined, while the other is still at the stage of early estimation."

Jan 1, 2014

By F. Petersen, W. van Dyk, J. Bonsu, A. Isafiade

"This paper aims to demonstrate how a systemic approach can be applied to the analysis of the causes of accidents in South African mines. The accident analysis framework used was developed previously by the authors from the combination of the Mark III version of the Swiss Cheese model, Incident Cause Analysis Method (ICAM), the Nertney Wheel model, and safety management principles. Data on 91 accidents occurring from 2010 to 2012 at the site of a platinum mine in South Africa were used to populate the newly developed framework. The results obtained show that while routine violations (45% of all accidents analysed) were the most common form of human error, problems in the physical environment of workers were the most common workplace factor (39.6% of all accidents analysed). Furthermore, inadequate leadership was found to be the most common systemic factor responsible for accidents (51.6% of all accidents analysed). Some workplace factors were more commonly associated with particular unsafe acts than others, and some systemic factors were more associated with particular workplace factors than others. The outcome of this study demonstrates that systemic factors, rather than human errors and violations, are the chief causes of accidents in the mining sector. IntroductionThe mining industry is a very important sector of the South African national economy. A major factor threatening the sustainability of this industry is mining accidents, which frequently result in injuries or deaths, destruction of property, and pollution of the environment. In the past, mining accidents have led to the shutdown and threat of shutdown of mines (Ryan, 2008; Mail and Guardian, 2011). The country stands the risk of incurring significant losses if the mining industry continues to experience shutdowns. In 2012, the mining sector accounted for R262.7 billion (equivalent to US$32.83 billion) representing 8.3% of GDP directly, on a nominal basis (Chamber of Mines of South Africa, 2013).Mining safety is a global concern and has attracted significant international attention. This has precipitated various studies into different aspects of mining. Unfortunately, human error has been blamed for the majority of these accidents. A study by the US Bureau of Mines found that human error is the cause of almost 85% of all accidents (Patterson and Shappell, 2008). In Australia, it is the cause of two out of every three occupational accidents (Patterson and Shappell, 2008). Various mining companies maintain that they run efficient systems, and hence the behavioural problems of workers are to blame for most accidents. An understanding of accident causality could be a major step in the quest to reduce accidents. Only with a good understanding of the accident process can effective remedies can be designed."

Jan 1, 2017

Fathi Habashi, Chalcopyrite. Its chemistry and metallurgy. New York, McGraw-Hill, 1978. 165 pp. RI9,95. Loss prevention and safety promotion The Proceedings of the 2nd International Symposium on Loss Prevention and Safety Promotion in the Process Industries, Heidelberg, 6th to 9th September, 1977, are now available. Chemical reaction engineering The Proceedings of the 4th International/6th European Symposium on Chemical Reaction Engineering (4th ISCRE) held at Heidelberg, Federal Republic of Ge rmany, from 6th to 8th April, 1976, are available from DECHEMA Deutsche Gesellschaft fur Chemisches Apparatewesen, P.O.B. 970146, D-6000 Frankfurt/ Main, West Germany, at the price of DMlOO plus postage and packing. Books received The Institution of Mechanical Engineers Proceedings Volume 190. Tribos abstracts on friction lubrication wear. Published by BHRA Fluid Engineering, Cranfield, Bedford MK 43 OAJ England. Price £30 (UK), US$72 (Europe), Seawater corrosion handbook, edited by M. M. Schumaker. Noyes Data Corporation Publicity Department, Mill Road at Grand Ave., Park Ridge, NJ 07656. 494 pp. Australian mineral industry quarterly 31(1) 1978 and 31(2) 1978. Bureau of Mineral Resources, Geology and Geophysics, Box 378, Canberra City, ACT 2601 Australia. Subscriptions $8, individual number $2. Mineral and NIM reports Report no. 1996 The extraction of gold from chloride solutions. (10th Nov., 1978). Report no. 1898 Batch and pilot-plant tests on M erensky Reef ore from the Western Platinum Mine. (8th Jun., 1977; reissued 30th Jan., 1979). Report no. 1920 A mineralogical investigation of Mamatu'an and Wessels manganese ores. (15th Sep., 1977; reissued 3rd Jan., 1979). Report no. 1978 The preparation and certification of a referencesample of magnetite ore. (22nd Dec., 1978). Report no. 1998 Electrode response to the addition of zinc during the cementation of gold. (25th Jan., 1979). Report no. 2002 The spectrochemical determination of phosphorus, magnesium, and iron in phosphate rocks and sulphuric acid leach liquors. (26th January, 1979). Report no. 1992 The use of emission spectrometry for the determination of impurities in metals. (24th Jan., 1979). Report no. 2003 An electrodeless conductivity meter of improved sensitivity and reliability. (28th Feb., 1979). Report no. 2005 The spectrometric analysis of manganese-bearing materials with particular reference to ferromanganese slags and metals. (16th Mar., 1979). Report no. 2006 An examination of procedures for the analysis of dry powders by atomic-absorption spectrophotometry. (28th Feb., 1979). Report no. 2007 The instrumentation and computerization of a 25 MV.A submerged -arc furnace. (25th Mar., 1977; reissued 16th Mar., 1979). Corrosion The International Corrosion Council has decided to hold the next Internat ional Congress on Corrosion in Mainz, Federal Republic of Germany, from 6th to 11th September, 1981. Process control The First European Symposium on Real -time Datahandling and Process Control will be held in West Berlin from 23rd to 25th October, 1979. Geomechanics The 28th Geomechanics Colloquy, organized by the Oosterreichische Gesellschaft fur Geomechanik, is to be held at Salzburg on 18th and 19th October, 1979. Geosta tistics A short course on 'Geostatistics for exploration and production planning' is being conducted by the Applied Earth Sciences Department, Stanford University, California, from 27th to 31st August, 1979. Business administration The Twelfth Executive Development Programme of the Graduate School of Business Administration, University of the Witwatersrand, is to be held from 9th July to 17th August, 1979. The engineer and the law A series of four meetings on the above subject is being conducted by the Measurement, Computation and Control SubCommittee of The South African Institute of Electrical Engineers. Lead smelter for South Africa? The National Institute for Metallurgy and Gold Fields of South Africa are making a comprehensive joint investigation of the technical and economic viability of an integrated lead smelter. Conference on titanium The Fourth International Conference on Titanium will be held from 19th to 22nd May, 1980, in Kyoto, Japan.

Jan 1, 1979

By W. K. Brinsden

In August 1965, the late Mr Alan Smith, then Mill Superintendent at Gold Mines of Kalgoorlie (GMK), Australia, asked me to investigate the planting of vegetation on the GMK slimes dams in order to ease the dust problem in urban and industrial areas-a problem that is caused largely by dust from these barren slimes dams. My early sources of information were the comprehensive papers in various issues of the Journal of The South African Institute of Mining and Metallurgy. However, the climate of Johannesburg differs from that of Kalgoorlie. The average Johannesburg rainfall, which falls mostly in summer, is 730 mm, and the average maximum summer temperature is 26°C (top 34°C). The winters are cool, the average maximum being 18°C (low -7°C). Kalgoorlie, on the other hand, receives, on average, 257 mm of sporadic rainfall, has hot dry summers with an average maximum of 35°C (top 45°C), and cool winters with an average maximum of 18°C (low -2°C). My obvious choice was to look at established trees growing on the GMK lease. A number of Athel pines were growing vigorously adjacent to the Oroya mining and geology offices and also on a nearby sand dump. The Athel pine (Tamarix aphylla), which is native to North Africa, Asia, and India, was originally introduced into Australia in 1936 by Mr Essington Lewis, then manager of BHP. His cuttings were planted in Whyalla, where some difficulty had been experienced in finding trees and shrubs that would flourish despite the district's low rainfall. In August 1965, cuttings of approximately 20 cm length and 1 cm diameter were taken from the GMK trees, stripped of leaves, and placed in jars of water in the sun. When the cuttings had sprouted both leaves and roots, they were planted in local soil in tins (about 20 cm high and 10 cm in diameter), and watered daily. In October 1965, when the new shoots were about 8 cm long, the trees were transplanted onto a lower flat section¬approximately 30 m wide, 30 m long, and 2 m high-of the Trafalgar slimes dam. No additional soil or fertilizer was used, and the trees were planted in their tins, the bases of which had been removed (the tin would eventually rust away). A few common varieties of non-prickly cactus and two native salt bush (spp Atriplex) were also planted, but did not survive, probably because of the acidity of the slime. During the summer of 1965/1966, Kalgoorlie's rainfall was 88 per cent above the average, and this probably helped the trees to survive. The moisture content was usually about 2,5 per cent from about 10 cm below the surface, and the pH value of the slime (d80 approximately 75 µm) was about 6. The trees were watered twice a week for the first four months and then left untended. By 1974 they had grown to only about 0,7 m, which indicated that their growth in slime was very slow. Other Athel pines were planted on the wall of the dam, but did not survive beyond 1974, probably because of the steep (about 500) slope and the hardness of the walls, which were initially formed by hand-shovelling of the slime as the height of the dam was raised. Five of the six Athel pines planted in 1965, which probably reached maturity (approximately 5 m in height) in 1981-16 years after being planted-have survived. In the early 1980s, waste rock had to be dumped on the dam, but the management of KMA (now KCGM) took care to ensure that the trees were not buried. Trials are being conducted on other tailings dams so that the performance of cuttings taken from the trees on Trafalgar dam can be compared with that of cuttings taken at various sites in Western Australia. It might also be worth while for an attempt to be made to strike cuttings from Trafalgar dam in pots containing different mixtures of soil and slime.

Jan 1, 1991

By R. Pretorius, N. Mautsa

In a cobalt precipitation plant, phosphoric acid is used to eliminate excess uranium from the pregnant leach solution, resulting in a cobalt hydroxide product that has little uranium contamination. However, the amount of phosphoric acid added must be monitored and controlled to avoid financial and sustainability impacts and to prevent negative impacts on the final product quality. One possible solution to this problem is the use of online residual phosphorus measurement techniques to regulate the addition. By continuously monitoring the residual phosphorus levels in the solution, the plant can adjust dosing in real time to maintain the target residual phosphorus level. As a result, the cobalt precipitation plant can improve phosphorus level control, lowering the risk of overdosing, and ensuring consistent product quality. This approach can also improve process efficiency, reduce operational costs, and have a positive environmental impact

Jan 1, 2023

By N. du Preez, J. Christie, F. Crundwell

Precipitation is a key process in the recovery of copper and cobalt. While there is a wealth of experience in operating precipitation steps, improving their performance remains challenging. Chemically, the reaction might be controlled by reaction kinetics, be limited by oxygen mass transfer, or be at equilibrium. In this paper, we examine these different operating regimes and demonstrate how they can be identified from plant operating data, process modelling, and pilot plant test work

Jan 1, 2023

By M. Asghari, R. Amiri, A. Haratian, M. Noue Parast, S. Haji

Today the roller screen has a wide range of applications in the steel-making industry. It is used for screening of green pellets before using the kiln. Since the appropriate size of a green pellet is -16+9 mm, there are different gaps between rollers that make green pellets classified in three categories: -9 mm (undersize), -16+9 mm (onsize) and +16mm (oversize). The efficiency of a roller screen is specified according to the weight percent of undersize in onsize as a fine material, and weight percent of onsize in oversize (loss). This efficiency is influenced by different operational parameters such as roller diameter, roller speed, and roller gap, material type of rollers and inclination of roller screen. This study investigates the effect of different material types of rollers in efficiency of Ardakan roller screens, located in the Yazd province of Iran. The rollers of the existing roller screens in this pelletising plant are made of polyurethane which according to this investigation, has a maximum lifetime of about six months. Operating the polyurethane rollers beyond its lifetime generates serious problems such as high wear of rollers, and consequently, material buildup on the roller surface which then significantly decreases the roller screen efficiency. So, after examining different roller materials, stainless steel 304 with higher surface roughness to help pellets move properly on the roller screen surface was selected as a solution to this problem. The new roller screen was constructed by Fakoor Meghnatis Spadana (FMS) and replaced the previous one. In this way, the maximum capacity of the roller screen was increased about 17% and the roller screen efficiency was increased about 15%. Keywords: Roller screen, green pellets, efficiency, onsize, operational parameters

Jan 1, 2020

By M. de Paiva Bueno, G. Barakos, S. Luukkanen, K. Luolavirta

Lifelong development of skills and knowledge of mining professionals has been recognised worldwide as a challenge for the development of a sustainable mining sector. Practical training and learning over the mine value chain are among the key components of this knowledge building. However, the number of available mining sites for continuous education in real-life conditions is limited; also the specifications for practical training are not clearly defined. The project MINETRAIN was developed to (i) evaluate the potential of the shortly-closing Pyhäsalmi Mine, in Finland, as an educational and training underground facility, and thus, prolong the utility of the existing modern mine site, and to (ii) develop and test practical training programs for mining and mining industry related professionals. Pyhäsalmi facilities enable training among all disciplines related to the overall mine value chain and hence, the project has potential in providing education for sustainable management of any phase of mining operations. The philosophy underpinning the MINETRAIN approach to mining activities is to assist the clients in minimising the technical and financial risks by providing a competitive and skilled personnel asset while optimising the value drivers in their operations. As a first major step of the project, a pilot training course, involving basic-level online theory and hands-on training at the Pyhäsalmi mine site, was undertaken in summer 2019. Feedback from the pilot test group of mining professionals has proved to be very positive. The comments from the participants strongly emphasised the added value of the practical onsite training for improved understanding in the large scale picture of mining on the entire value chain. As a second phase of the project, a new test course was launched in June 2020. The second MINETRAIN course focuses on new technologies and digitisation in mining. Keywords: Lifelong learning, mining education, mine value chain, research and education mine, educational research project

Jan 1, 2020

By M. Arlandi-Rodríguez, and A. García-Berrocal, A. Alonso-Jiménez, C. Lopez-Jimeno

Spain is a major producer of dimension stone, which is one of the most important industrial sectors in the northwest of Spain. This justifies the maintenance of these industries, although the technical and environmental requirements for their continuity are increasingly demanding. The main target of this paper is to present a new methodology in order to obtain k-ratio stress values on the basis of flat jack measurements and finite element numerical back- analysis with Rocscience© RS2 software. Continuous iterations were performed to try to find a relationship between the k₀ and the measured stress in the tunnel roof and sidewalls. It focuses on technical aspects of the method for designing mine chambers in the slate industry that were previously mined by open pit methods. The size of the chambers impacts the operating cost, and the dimensioning of a correct support ensures better efficiency and safety. Correct knowledge of the k₀ therefore is critical for the design of the support. The proposed new method entails a simplification of the classical procedure for estimating the k-ratio.

Sep 1, 2022

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

By D. Odendaal, S. Bharat, R. D. Cromarty

The aim of this investigation was to determine the effect of high-temperature heat treatment on the electrical resistivity of charcoal. Samples of two different wood types (eucalyptus and black wattle) were pyrolised in a retort at a temperature of 700°C and the resulting charcoals heat-treated in an induction furnace at temperatures from 800°C to 1800°C and residence times from 60 to 120 minutes. After cooling, the resistivities of the samples were measured at room temperature using the four-point probe technique. It was found that as the heat treatment temperature increased the electrical resistivity of the charcoal decreased, approaching an asymptotic value at higher temperatures. Longer residence times decreased the resistivity, but this effect was not pronounced.

Oct 3, 2023

By M. Z. Emad, S. Raza, K. Jalil, M. A. Raza, M. U. Khan, S. A. Saki

Dimension stone mining is Increasing because of growing demand from the building and construction industries. Diamond wire saw cutting is a popular dimension stone mining technique around the world. Estimation of the production cost for this method is critical for these operations. n this research a production cost model was developed for the mining of granite using a diamond wire saw. Cost and production data were collected from a granitic dolerite operation in Pakistan for a 4.5-year period, and analysed to identify the cost components. Fuel (34%), labour (15%), consumables (40%), and maintenance (5%) were found to be the four major cost components in this operation. A regression-based dimension stone production cost model incorporating statistically significant variables was developed. The data presented a strong correlation of production cost with fuel, labour, and consumables costs. Finally, a production cost model based on the consumption cost of diamond wire is presented. The model was verified using actual production cost data, which indicated 95% (R2 = 0.95) variance in the data between the predicted and actual production cost values. The model may help field engineers in computing their dimension stone operational cost during the cutting phase.

Nov 6, 2023

By C. E. More

Some observations on 'ancient' mining at Phalaborwa C. E. MORE. B.A. (Pretoria) (Visitor) A brief account is given of historical references to the Phalaborwa area, the first being to the mountain of copper and iron sought by Francois de Cuiper in 1725. These are followed by a description of several finds in the area, which are related to finds described in the literature and to Bantu tradition on the subject. Phalaborwa is one of the earliest known mining sites in the Republic of South Africa, Loolekop having been a mining centre, as shown by carbon-14 dating, since 770 A.D.

Jan 1, 1974

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By L. A. Balzan, M. Kalicinski, F. Nieuwenhuys

GEOSCANs on belt analysers have been widely utilised in iron ore for nearly two decades. Since the first installations in 2003, the availability of accurate and reliable grade data has become standardised across iron ore mines in the Northern Cape, where various streams are monitored continuously to ensure the optimal functioning of plants. Assmang Khumani has been at the forefront of technology adoption and has implemented 19 GEOSCANs at various locations throughout the plant, monitoring run-of-mine, stockyard feed, beneficiation plant feeds, and products. Over the years, collaborative advances in the technology have allowed for numerous benefits and gains to be made. In recent times, there has been a concerted effort on the development of analysis for phosphorus in the material flows, and based on Scantech's experience in the phosphate industry, this element has now been calibrated to achieve statistically acceptable and repeatable accuracies for real time analysis of this element on many of Khumani's GEOSCAN analysers. This paper provides an overview of GEOSCAN use at Khumani, while focusing on the development of phosphorus analysis. A case study of analysis results is presented for a range of analysers that have been calibrated for this element, as well as a discussion on the benefits obtained as a result of this analysis. Keywords: Online analysis, real-time, process control

Jan 1, 2020

By E. Arghavani, S. H. Amiri, S. Zare, F. Sepehri, M. Ramezanizadeh

Mineral processing plants include different stages like crushing, grinding, classification and concentration, all of which have partially affect the final product. To identify and solve the related problems of each stage, process audition should be carried out continuously to find the major solutions of improving product and decreasing the maintenance and operating costs. The Iranian Gohar-Zamin iron ore beneficiation plant consists of equipment such as gyratory and cone crushers, high pressure grinding rolls (HPGR), ball mill, dry and wet double-deck vibrating screens, hydrocyclones cluster, magnetic drum separators, thickener and horizontal vacuum belt filters. The defects of initial design as well as current non-standard operating conditions of equipment were monitored and detected and the opportunities for process optimisation were presented as follows: establishing the control loop of power draw for cone crushers, the modification of feeding chute in cone crushers to minimise the non-uniform wear of parts, removing segregation in the fresh feed bin and screen’s circulating load chute in order to provide the proper feed to HPGR, reducing wear rate on HPGR rolls surfaces, decreasing the amount of rejected materials in screen, equalising the solid content and particle size distribution (PSD) of feed in all magnetic drum separators and equalising the PSD of hydrocyclones overflow. This paper provides a guideline for the mineral processing industry to focus its efforts on process design to deliver the efficiency with minimum capital costs. Keywords: Process audition, gyratory crusher, cone crusher, HPGR, screening, hydrocyclones, magnetic drum separators

Jan 1, 2020

By M. J. Latva-Kokko, CA Snyders, J. R. Peltola, M. K. Kostiainen

It is well known that carbon management is essential for minimising soluble gold losses in carbonin- leach (CIL) and carbon-in-pulp (CIP) circuits. Even so, carbon measurements remain predominantly a manual operation with a low amount of control and automation around CIL and CIP reactors. Carbon inventory, i.e. knowing the carbon concentration in each reactor, is crucial for good carbon management. CarbonSense, a novel in-situ measurement system, was therefore developed for continuous monitoring of the carbon concentration in each reactor and paves the way for more advanced control in gold operations. The carbon management and optimisation system is based on Outotec® HSC Sim dynamic process simulations where each process component is modelled in detail. Generated models are validated with real data from a particular operation. The simulator will allow for the carbon control sequence to be realistically tested and the efficiency optimised by controlling the feed and discharge pumps in a hazard- and risk-free process environment. Furthermore, by combining CarbonSense and Outotec® gold courier (online soluble gold measurements) continuous feed-forward and feedback information can be obtained. The optimiser will then define the best running parameters based on the cost function of gold production versus intrinsic factors such as utility costs and adsorption time. Eventually, the application can be installed parallel with a real process island and it can be continuously calibrated with real-time process data. The dynamic model will then create future predictions for the entire process island. The example case presents a CIL circuit, which is simulated using Outotec® HSC Chemistry Sim and operated through Outotec® ACT (Advanced Control Tool) application. Keywords: Carbon-in-leach, CIL, CarbonSense, carbon management, automated control, simulation

Jan 1, 2020